Effect of Bi/Si Ratio of BiBSi Glass on Its Structure, Properties and Laser Sealing Shear Strength for Vacuum Glazing

The low-melting glass of Bi2O_(3)-B2O_(3)-SiO_(2)(BiBSi)system was used for the first time for laser sealing of vacuum glazing.Under the condition of constant boron content,how the structure and properties vary with Bi/Si ratio in low-melting glass was investigated.In addition,the relationships between laser power,low-melting glass solder with different Bi/Si ratios and laser sealing shear strength were revealed.The results show that a decrease in the Bi/Si ratio can cause a contraction of the glass network of the low-melting glass,leading to an increase of its characteristic temperature and a decrease of its coefficient of thermal expansion.During laser sealing,the copper ions in the low-melting glass play an endothermic role.A change in the Bi/Si ratio will affect the valence state transition of the copper ions in the low-melting glass.The absorbance of the low-melting glass does not follow the expected correlation with the Bi/Si ratio,but shows a linear correlation with the content of divalent copper ions.The greater the concentration of divalent copper ions,the greater the absorbance of the low-melting glass,and the lower the laser power required for laser sealing.The shear strength of the low melting glass solder after laser sealing was tested,and it was found that the maximum shear strength of Z1 glass sample was the highest up to 2.67 MPa.

Memristive feature and mechanism induced by laser-doping in defect-free 2D semiconductor materials

Memristors as non-volatile memory devices have gained numerous attentions owing to their advantages in storage,in-memory computing, synaptic applications, etc. In recent years, two-dimensional(2D) materials with moderate defects have been discovered to exist memristive feature. However, it is very difficult to obtain moderate defect degree in 2D materials, and studied on modulation means and mechanism becomes urgent and essential. In this work, we realized memristive feature with a bipolar switching and a configurable on/off ratio in a two-terminal MoS_(2) device(on/off ratio ~100), for the first time, from absent to present using laser-modulation to few-layer defect-free MoS_(2)(about 10 layers), and its retention time in both high resistance state and low resistance state can reach 2×10^(4) s. The mechanism of the laser-induced memristive feature has been cleared by dynamic Monte Carlo simulations and first-principles calculations. Furthermore, we verified the universality of the laser-modulation by investigating other 2D materials of TMDs. Our work will open a route to modulate and optimize the performance of 2D semiconductor memristive devices.

Multipass welding of thick section steels using autogenous CO2 laser welding and CO2 laser-MIG hybrid welding

Laser multipass welding techniques for thick section steels have been developed using a new type of UV combined narrow groove. The shape and sizes at the bottom of groove are determined by analyzing the plasma behavior using high speed photographic equipment. A stable autogenous CO2 laser welding process and greater penetration are generated at the root pass because of strong reduction of the plasma volume. According to the waveforms of welding current and arc voltage, and the interaction between the arc and the laser induced plasma, a suitable groove angle is obtained. Laser-double MIG hybrid welding process is studied and the optimum distances between the laser and two arcs are determined. By using autogenous CO2 laser welding, CO2 laser-MIG hybrid welding and laser-double MIG hybrid welding, 28 mm thick steel plates are welded with four passes. The welds produced are assessed by X-ray. No crack is found and there is only a small amount of pores. The experimental results show that the multipuss welding procedures proposed can realize the joining of thick section steels with high efficiency and good quality.

Electrokinetic-mechanism of water and furfural oxidation on pulsed laser-interlaced Cu_(2)O and CoO on nickel foam

The electrocatalytic oxidation of biomass-derived furfural(FF)feedstocks into 2-furoic acid(FA)holds immense industrial potential in optics,cosmetics,polymers,and food.Herein,we fabricated Co O/Ni O/nickel foam(NF)and Cu_(2)O/Ni O/NF electrodes via in situ pulsed laser irradiation in liquids(PLIL)for the bifunctional electrocatalysis of oxygen evolution reaction(OER)and furfural oxidation reaction(FOR),respectively.Simultaneous oxidation of NF surface to NiO and deposition of CoO and/or Cu_(2)O on NF during PLIL offer distinct advantages for enhancing both the OER and FOR.CoO/NiO/NF electrocatalyst provides a consistently low overpotential of~359 m V(OER)at 10 m A/cm^(2),achieving the maximum FA yield(~16.37 m M)with 61.5%selectivity,79.5%carbon balance,and a remarkable Faradaic efficiency of~90.1%during 2 h of FOR at 1.43 V(vs.reversible hydrogen electrode).Mechanistic pathway via in situ electrochemical-Raman spectroscopy on CoO/NiO/NF reveals the involvement of phase transition intermediates(NiOOH and CoOOH)as surface-active centers during electrochemical oxidation.The carbonyl carbon in FF is attacked by hydroxyl groups to form unstable hydrates that subsequently undergo further oxidation to yield FA products.This method holds promise for large-scale applications,enabling simultaneous production of renewable building materials and fuel.

Effects of RFTVR and CO2 laser on symptoms improvement, QOL and vas of patients with early laryngeal cancer

Objective: To study the effect of RFTVR and CO2 laser on the improvement of symptoms, QOL and vas of patients with early laryngeal cancer. Methods: In this study, 120 patients with laryngeal cancer diagnosed and treated from January 2015 to December 2016 were taken as research objects. All patients were randomly divided into observation group and control group, 60 patients in each group. Patients in observation group were treated with RFTVR, and patients in control group were treated with new-type fiber-optic CO2 laser. The patients in the two groups were treated with cisplatin injection. The differences of perioperative indexes, swallowing function, pronunciation function, survival period, QOL score and VAS score between the two groups were compared. Results: There was no significant difference in the amount of intraoperative bleeding, operation time and hospitalization time between the two groups (P > 0.05);the correct swallowing of the observation group was significantly higher than that of the control group. After treatment, jitter, shimmer and HNR of the two groups were significantly improved, and jitter and shimmer of the observation group were significantly lower than that of the control group, and HNR was significantly higher than that of the control group (P < 0.05) The QOL score and VAS score of the two groups were significantly improved, and the QOL score of the observation group was significantly higher than that of the control group and the VAS score was significantly lower than that of the control group (P < 0.05);the total survival period and tumor free survival period of the observation group were significantly higher than that of the control group. Conclusion: Compared with CO2 laser treatment, the swallowing function and voice function of patients treated by low temperature plasma radiofrequency ablation were significantly improved, and the life quality of patients was significantly improved by prolonging the survival period of patients..

Investigations on MoS_(2)plasma by infra-red pulsed laser irradiation in high vacuum

MoS_(2)targets were irradiated by infra-red(IR)pulsed laser in a high vacuum to determine hot plasma parameters,atomic,molecular and ion emission,and angular and charge state distributions.In this way,pulsed laser deposition(PLD)of thin films on graphene oxide substrates was also realized.An Nd:YAG laser,operating at the 1064 nm wavelength with a 5 ns pulse duration and up to a 1 J pulse energy,in a single pulse or at a 10 Hz repetition rate,was employed.Ablation yield was measured as a function of the laser fluence.Plasma was characterized using different analysis techniques,such as time-of-flight measurements,quadrupole mass spectrometry and fast CCD visible imaging.The so-produced films were characterized by composition,thickness,roughness,wetting ability,and morphology.When compared to the MoS_(2)targets,they show a slight decrease of S with respect to Mo,due to higher ablation yield,low fusion temperature and high sublimation in vacuum.The pulsed IR laser deposited Mo Sx(with 1<x<2)films are uniform,with a thickness of about 130 nm,a roughness of about 50 nm and a higher wettability than the MoS_(2)targets.Some potential applications of the pulsed IR laser-deposited Mo Sx films are also presented and discussed.

Pulsed laser interference patterning of transition-metal carbides for stable alkaline water electrolysis kinetics

We investigated the role of metal atomization and solvent decomposition into reductive species and carbon clusters in the phase formation of transition-metal carbides(TMCs;namely,Co_(3)C,Fe_(3)C,TiC,and MoC)by pulsed laser ablation of Co,Fe,Ti,and Mo metals in acetone.The interaction between carbon s-p-orbitals and metal d-orbitals causes a redistribution of valence structure through charge transfer,leading to the formation of surface defects as observed by X-ray photoelectron spectroscopy.These defects influence the evolved TMCs,making them effective for hydrogen and oxygen evolution reactions(HER and OER)in an alkaline medium.Co_(3)C with more oxygen affinity promoted CoO(OH)intermediates,and the electrochemical surface oxidation to Co_(3)O_(4)was captured via in situ/operando electrochemical Raman probes,increasing the number of active sites for OER activity.MoC with more d-vacancies exhibits strong hydrogen binding,promoting HER kinetics,whereas Fe_(3)C and TiC with more defect states to trap charge carriers may hinder both OER and HER activities.The results show that the assembled membrane-less electrolyzer with Co_(3)C∥Co_(3)C and MoC∥MoC electrodes requires~2.01 and 1.99 V,respectively,to deliver a 10 mA cm−2 with excellent electrochemical and structural stability.In addition,the ascertained pulsed laser synthesis mechanism and unit-cell packing relations will open up sustainable pathways for obtaining highly stable electrocatalysts for electrolyzers.

Observation on clinical effect of botulinum toxin type A injection combined with low-energy CO2 fractional laser periocular rejuvenation treatment

Objective To investigate the clinical effect of botulinum toxin type A injection combined with low-energy CO2 fractional laser periocular rejuvenation treatment.Methods The clinical effect of botulinum type A injection alone and botulinum type A injection combined with low-energy CO2 fractional laser was compared in 96 patients who needed to receive periocular rejuvenation treatment from April 2018 to April 2019.Results After the combined low-energy CO2 fractional laser treatment was given on the basis of botulinum toxin type A injection,the follow-up global aesthetic improvement scale(GAIS)scores of the observation group were 86.78±4.67,80.31±3.66,76.94±4.03 and 40.59±4.78.The global aesthetic improvement of the dynamic and static wrinkles was obvious.The total effective rate was 93.7%.The total satisfaction rate of the patients was 95.8%,which was higher than that of the control group(P<0.05).The clinical efficacy was significant.Conclusion The application of the combined periocular rejuvenation treatment can improve the dynamic and static wrinkles simultaneously with remarkable rejuvenation effect,increase the effective rate of treatment and enhance the patients'satisfaction.

Clinical study of treatment of facial scar with ultrapulse CO2 laser and Erbium fractional laser

Objective To observe the effect of uitrapulse CO2 laser combined with Erbium fractional laser on treatment facial scars. Methods Total 70 cases with facial scars were treated with ultrapulse CO2 laser combined with Erbium fractional laser for 3 times with 2 ～ 3 months interval. Firstly,scar resurfacing was performed

Role of processing parameters on relative density,microstructure and mechanical properties of selective laser melted titanium alloy

The relationships between the selective laser melting(SLM)processing parameters including laser power,scanning speed and hatch space,the relative density,the microstructure,and resulting mechanical properties of Ti-6Al-2Zr-1Mo-1V alloy were investigated in this work.The result shows that laser power acts a dominant role in determining the relative density in comparison with scanning speed and hatch space.The optimal SLM process window for fabricating relative density>99%samples is located in the energy density range of 34.72 J·mm^(-3)to 52.08 J·mm^(-3),where the laser power range is between 125 W and 175 W.An upward trend is found in the micro-hardness as the energy density is increased.The optimum SLM processing parameters of Ti-6Al-2Zr-1Mo-1V alloy are:laser power of 150 W,scanning speed of 1,600 mm·s^(-1),hatch space of 0.08 mm,and layer thickness of 0.03 mm.The highest ultimate tensile strength,yield strength,and ductility under the optimum processing parameter are achieved,which are 1,205 MPa,1,099 MPa,and 8%,respectively.The results of this study can be used to guide SLM production Ti-6Al-2Zr-1Mo-1V alloy parts.

Thulium laser treatment for bladder cancer

Recent innovations in thulium laser techniques have allowed application in the treatment of bladder cancer.Laser en bloc resection of bladder cancer is a transurethral procedure that may offer an alternative to the conventional transurethral resection procedure.We conducted a review of basic thulium laser physics and laser en bloc resection procedures and summarized the current clinical literature with a focus on complications and outcomes.Literature evidence suggests that thulium laser techniques including smooth incision,tissue vaporization,and en bloc resection represent feasible,safe,and effective procedures in the treatment of bladder cancer.Moreover,these techniques allow improved specimen orientation and accurate determination of invasion depth,facilitating correct diagnosis,restaging,and reevaluation of the need for a second resection.Nonetheless,large-scale multicentre studies with longer follow-up are warranted for a robust assessment.The present review is meant as a quick reference for urologists.

Effect of laser characteristics on the weld shape and properties of penetration laser weld of BT20 titanium alloy

The laser beam welding of BT20 titanium alloy was conducted to investigate the weld shape, microstructures and properties. The full penetration weld characteristics produced by CO_2 laser and by YAG laser were compared. The results show that the full penetration weld of YAG laser welding closes to “X” shape, and weld of CO_2 laser welding is “nail-head” shape. Those result from special heating mode of laser deep penetration welding. The tension strength of CO_2 laser and YAG laser joints equal to that of the base metal, but the former has better ductility. All welds consist mainly of the acicular α phase and a few β phase in microstructure. The dendritic crystal of CO_2 laser weld is a little finer than YAG laser weld. According the research CO_2 laser is better than YAG laser for welding of BT20 titanium alloy.

Observation and optimization of 2 μm mode‐locked pulses in all‐fiber net anomalous dispersion laser cavity

We integrally demonstrate 2μm mode-locked pulses performances in all-fiber net anomalous dispersion cavity.Stable mode-locking operations with the center wavelength around 1950–1980 nm can be achieved by using the nonlinear polarization rotation structure and properly designing the dispersion management component.Conventional soliton is firstly obtained with a total anomalous dispersion cavity.Due to the contribution of commercial ultra-high numerical aperture fibers,net dispersion is reduced to-0.077 ps2.So that stretched pulse with 19.4 nm optical bandwidth is obtained and the de-chirped pulse-width can reach 312 fs using extra-cavity compression.Under pump power greater than 890 mW,stretched pulse can evolve into noise-like pulse with 41.3 nm bandwidth.The envelope and peak of such broadband pulse can be compressed with up to 2.2 ps and 145 fs,respectively.The single pulse energy of largely chirped stretched and noise-like pulse can reach 1.785 nJ and 1.53 nJ,respectively.Furthermore,extra-cavity compression can also contribute to a significant increase of peak power.

Simulation of Patterns and Qualitative Analysis of Pattern Rotation in an End-Pumped Nd：YVO4 Laser

We simulate some laser output patterns observed in our previous experiment employing superposition of Laguerre- Gaussian modes. The rotating pattern is qualitatively analysed from the point of contemporary spatial burning hole effect of the lasing crystal.

Microstructure of TA2/TA15 graded structural material by laser additive manufacturing process

TA2/TA15 graded structural material（GSM） was fabricated by the laser additive manufacturing（LAM） process. The chemical composition, microstructure and micro-hardness of the as-deposited GSM were investigated. The results show that the TA2 part of exhibiting near-equiaxed grains was Widmanst？tten α-laths microstructure. The TA15 part containing large columnar grains was fine basket-weave microstructure. The graded zone was divided into four deposited layers with 3000 μm in thickness. As the distance from the TA2 part increases, the alloy element contents and the β phase volume fraction increase, the α phase volume fraction decreases and the microstructure shows the evolution from Widmanst？tten α-laths to basket-weave α-laths gradually. The micro-hardness increases from the TA2 part to the TA15 part due to the solid solution strengthening and grain boundary strengthening.

Synthesis of Y_2O_3 particle enhanced Ni/TiC composite on TC4 Ti alloy by laser cladding

A Y2O3 particle enhanced Ni/TiC composite coating was fabricated in-situ on a TC4 Ti alloy by laser surface cladding. The phase component, microstructure, composition distribution and properties of the composite layer were investigated. The composite layer has graded microstructures and compositions, due to the fast melting followed by rapid solidification and cooling during laser cladding. The TiC powders are completely dissolved into the melted layer during melting and segregated as fine dendrites when solidified. The size of TiC dendrites decreases with increasing depth. Y2O3 fine particles distribute in the whole clad layer. The Y2O3 particle enhanced Ni/TiC composite layer has a quite uniform hardness along depth with a maximum value of HV1380, which is 4 times higher than the initial hardness. The wear resistance of the Ti alloy is significantly improved after laser cladding due to the high hardness of the composite coating.

Interface characteristics of Al_2O_3－13%TiO_2 ceramic coatings prepared by laser cladding

Al2O3-13%TiO2 （mass fraction） coatings, prepared by laser cladding on nickel-based alloy, were heated using high frequency induction sources. The coating microstructure and the interface between bond coating and ceramic coating were characterized by SEM, XRD and EDS. The results show that two-layer substructure exists in the ceramic coating： one layer evolving from fully melted region where the sintered grains grow fully; another layer resembling the liquid-phase-sintered structure consisting of three-dimensional net where the melted Al2O3 particles are embedded in the TiO2-rich matrix. The mechanism of the two-layer substructure formation is also explained in terms of the melting and flattening behavior of the powders during laser cladding processing. The spinel compounds NiAl2O4 and acicular compounds Cr2O3 are discovered in the interface between bond coating and ceramic coating. It proves that the chemical reactions in the laser cladding process will significantly enhance the coating adhesion.

Diagnostics of laser-induced plasma on carbon-based polymer material using atomic and molecular emission spectra

Time-integrated optical emission analysis of laser-induced plasma on Teflon is presented.Plasma was induced under atmospheric pressure air using transversely excited atmospheric CO_(2) laser pulses.Teflon is a C-based polymer that is,among other things,interesting as a substrate for laser-induced breakdown spectroscopy analysis of liquid samples.This study aimed to determine the optimal experimental conditions for obtaining neutral and ionized C spectral lines and C2 and CN molecular band emission suitable for spectrochemical purposes.Evaluation of plasma parameters was done using several spectroscopic techniques.Stark profiles of appropriate C ionic lines were used to determine electron number density.The ratio of the integral intensity of ionic-to-atomic C spectral lines was used to determine the ionization temperature.A spectral emission of C2 Swan and CN violet bands system was used to determine the temperature of the colder,peripheral parts of plasma.We critically analyzed the use of molecular emission bands as a tool for plasma diagnostics and suggested methods for possible improvements.

Sub-pixel extraction of laser stripeand itsapplication in laser plane calibration

For calibrating the laser plane to implement 3D shape measurement, an algorithm for extracting the laser stripe with sub-pixel accuracy is proposed. The proposed algorithm mainly consists of two stages： two-side edge detection and center line extraction. First, the two-side edge of laser stripe is detected using the principal component angle-based progressive probabilistic Hough transform and its width is calculated through the distance between these two edges. Secondly, the center line of laser strip is extracted with 2D Taylor expansion at a sub-pixel level and the laser plane is calibrated with the 3D reconstructed coordinates from the extracted 2D sub-pixel ones. Experimental results demonstrate that the proposed method can not only extract the laser stripe at a high speed, nearly average 78 ms/frame, but also calibrate the coplanar laser stripes at a low error, limited to 0.3 mm. The proposed algorithm can satisfy the system requirement of two-side edge detection and center line extraction, and rapid speed, high precision, as well as strong anti-jamming.

Morphology and Mechanical Properties of PS/Al_2O_3 Nanocomposites Based on Selective Laser Sintering

Selective laser sintering （SLS） is a new process to prepare the polystyrene （PS）/Al2O3 nanocomposites. In this paper, with different laser power and other processing parameters unchanged, the morphology, density and mechanical properties of the sintered specimens were investigated. It was found that nano-sized inorganic particles are uniformly located in the PS matrix and the maximum density of the sintered specimens with pure PS powder reaches 1.07 g/cm^3, higher than 1.04 g/cm^3 that of the sintered specimens with mixture powder. Due to strengthening and toughness of the nano-sized Al2O3 inorganic particles, the maximum notched impact strength and tensile strength of the sintered part mixed with nano-sized inorganic particles are improved greatly from 7.5 to 12.1 kJ/m^2 and from 6.5 to 31.2 MPa, respectively, under the same sintering condition.