With the development of power plants towards high power and intelligent operation direction,the vibrations or failures of blades,especially the last stage blades in steam turbines,happen more frequently due to the uns...With the development of power plants towards high power and intelligent operation direction,the vibrations or failures of blades,especially the last stage blades in steam turbines,happen more frequently due to the unstable operating conditions brought by flexible operation.A vibration measuring method for the shrouded blades of a steam turbine based on eddy current sensors with high frequency response is proposed,meeting the requirements of non-contact heath monitoring.The eddy current sensors produce the signals which are related to the area changing of every blade’s shroud resulting from the rotation of stator.Then an improved blade tip timing(BTT)technique is proposed to detect the vibrations of shrouded blades by measuring the arrival time of each area changing signal.A structure of eddy current sensors is developed in steam turbines and an amplitude modulation/demodulation circuit is designed to improve the response bandwidth up to 250 kHz.Vibration tests for the last stage blades of a steam turbine were carried out and the results validate the efficiency of the improved BTT technique and the high frequency response of the eddy current sensors presented.展开更多
Localized nature of damage in structures requires local measurements for structural health monitoring. The local measurement means to measure the local, usually higher modes of the vibration in a structure. Three fund...Localized nature of damage in structures requires local measurements for structural health monitoring. The local measurement means to measure the local, usually higher modes of the vibration in a structure. Three fundamental issues about the local measurement for structural health monitoring including (1) the necessity of making local measurement, (2) the difficulty of making local measurement and (3) how to make local measurement are addressed in this paper. The results from both the analysis and the tests show that the local measurement can successfully monitor the structural health status as long as the local modes are excited. Unfortunately, the results also illustrate that it is difficult to excite local modes in a structure. Therefore, in order to carry structural health monitoring into effect, we must (1) ensure that the local modes are excited, and (2) deploy enough sensors in a structure so that the local modes can be monitored.展开更多
A new type optical fiber sensor--Tip timing Sensor is introduced in this paper. It is mostly used in vibration measurement of turbine blade, which can realize real-time and non-contact measurement.
An instnmaent awakened by means of vibration for single hydraulic prop pressame measuring is described in this paper. The principle and implementation of this metlmd are introduced in detail. The instnznent uses the h...An instnmaent awakened by means of vibration for single hydraulic prop pressame measuring is described in this paper. The principle and implementation of this metlmd are introduced in detail. The instnznent uses the hgh-perftmnance single chip C8051F310 as its MCU and vibration sensor as its awaking device. It has such advantages as small vohane and low power consmnption, and moreover it could resolve the problem that traditional pressure measming instrument on single hydraulic prop can＇t be used in coal mine.展开更多
This paper proposes a novel seismometer-type absolute displacement sensor aimed at detecting earthquake waves with a large magnitude and long period. However, since the measuring range of the displacement sensor is hi...This paper proposes a novel seismometer-type absolute displacement sensor aimed at detecting earthquake waves with a large magnitude and long period. However, since the measuring range of the displacement sensor is higher than its natural frequency, it is difficult to detect low frequency vibrations below 1 Hz using a conventional a seismic-type displacement sensor. In order to provide an absolute displacement detection which is capable of lowering the natural frequency and enlarging the detectable amplitude without causing structural defects, the relative signals of displacement, velocity, and acceleration between a detected object and the auxiliary mass of the sensor are fed back into the sensor. In addition, phase lag compensation is inserted to adjust phase angles, which are of a frequency of 1 Hz. According to simulation results, a detection range from 0.1 Hz to 50 Hz is expected. It has been demonstrated that the developed sensor with a small size and light weight has a detection range of from 0.5 Hz to 50 Hz for absolute displacement and velocity. As an additional advantage, the measurement displacement amplitude has been expanded to about 20 dB. This sensor is available to use for the active control method. of flexible structures like high rise buildings using the LQ control展开更多
The intelligent structural health monitoring method, which uses a fiber Bragg grating （FBG） sensor, is a new approach in the field of civil engineering. However, it lacks a reliable FBG-based accelerometer for takin...The intelligent structural health monitoring method, which uses a fiber Bragg grating （FBG） sensor, is a new approach in the field of civil engineering. However, it lacks a reliable FBG-based accelerometer for taking structural low frequency vibration measurements. In this letter, a fiextensional FBG-based accelerometer is proposed and demonstrated. The experimental results indicate that the natural frequency of the developed accelerometer is 16.7 Hz, with a high sensitivity of 410.7 pm/g. In addition, it has a broad and flat response over low frequencies ranging from 1 to 10 Hz. The natural frequency and sensitivity of the accelerometer can be tuned by adding mass to tailor the sensor performance to specific applications. Experimental results are presented to demonstrate the good performance of the proposed FBG-based accelerometer. These results show that the proposed accelerometer is satisfactory for low frequency vibration measurements.展开更多
A dual-frequency distributed Bragg reflector （DBR） fiber laser based sensor is demonstrated for low-frequency vibration measurement through the Doppler effect. The response of the proposed sensor is quite linear and...A dual-frequency distributed Bragg reflector （DBR） fiber laser based sensor is demonstrated for low-frequency vibration measurement through the Doppler effect. The response of the proposed sensor is quite linear and is much higher than that of a conventional accelerometer. The proposed sensor can work down to 1 Hz with high sensitivity. Therefore, the proposed sensor is very efficient in low-frequency vibration measurement.展开更多
基金National Natural Science Foundation of China(No.51775377)National Key Research and Development Plan(No.2017YFF0204800)+2 种基金Natural Science Foundation of TianJin City(No.17JCQNJC01100)Young Elite Scientists Sponsorship Program by Cast of China(No.2016QNRC001)Open Project of Key Laboratory of Underwater Information and Control(No.6142218081811)
文摘With the development of power plants towards high power and intelligent operation direction,the vibrations or failures of blades,especially the last stage blades in steam turbines,happen more frequently due to the unstable operating conditions brought by flexible operation.A vibration measuring method for the shrouded blades of a steam turbine based on eddy current sensors with high frequency response is proposed,meeting the requirements of non-contact heath monitoring.The eddy current sensors produce the signals which are related to the area changing of every blade’s shroud resulting from the rotation of stator.Then an improved blade tip timing(BTT)technique is proposed to detect the vibrations of shrouded blades by measuring the arrival time of each area changing signal.A structure of eddy current sensors is developed in steam turbines and an amplitude modulation/demodulation circuit is designed to improve the response bandwidth up to 250 kHz.Vibration tests for the last stage blades of a steam turbine were carried out and the results validate the efficiency of the improved BTT technique and the high frequency response of the eddy current sensors presented.
文摘Localized nature of damage in structures requires local measurements for structural health monitoring. The local measurement means to measure the local, usually higher modes of the vibration in a structure. Three fundamental issues about the local measurement for structural health monitoring including (1) the necessity of making local measurement, (2) the difficulty of making local measurement and (3) how to make local measurement are addressed in this paper. The results from both the analysis and the tests show that the local measurement can successfully monitor the structural health status as long as the local modes are excited. Unfortunately, the results also illustrate that it is difficult to excite local modes in a structure. Therefore, in order to carry structural health monitoring into effect, we must (1) ensure that the local modes are excited, and (2) deploy enough sensors in a structure so that the local modes can be monitored.
文摘A new type optical fiber sensor--Tip timing Sensor is introduced in this paper. It is mostly used in vibration measurement of turbine blade, which can realize real-time and non-contact measurement.
文摘An instnmaent awakened by means of vibration for single hydraulic prop pressame measuring is described in this paper. The principle and implementation of this metlmd are introduced in detail. The instnznent uses the hgh-perftmnance single chip C8051F310 as its MCU and vibration sensor as its awaking device. It has such advantages as small vohane and low power consmnption, and moreover it could resolve the problem that traditional pressure measming instrument on single hydraulic prop can＇t be used in coal mine.
文摘This paper proposes a novel seismometer-type absolute displacement sensor aimed at detecting earthquake waves with a large magnitude and long period. However, since the measuring range of the displacement sensor is higher than its natural frequency, it is difficult to detect low frequency vibrations below 1 Hz using a conventional a seismic-type displacement sensor. In order to provide an absolute displacement detection which is capable of lowering the natural frequency and enlarging the detectable amplitude without causing structural defects, the relative signals of displacement, velocity, and acceleration between a detected object and the auxiliary mass of the sensor are fed back into the sensor. In addition, phase lag compensation is inserted to adjust phase angles, which are of a frequency of 1 Hz. According to simulation results, a detection range from 0.1 Hz to 50 Hz is expected. It has been demonstrated that the developed sensor with a small size and light weight has a detection range of from 0.5 Hz to 50 Hz for absolute displacement and velocity. As an additional advantage, the measurement displacement amplitude has been expanded to about 20 dB. This sensor is available to use for the active control method. of flexible structures like high rise buildings using the LQ control
基金supported by the National Natural Science Foundation of China (Nos. 60727004 and 61077060)the National High Technology Research and Development Program of China (Nos. 2007AA03Z413 and 2009AA06Z203)+1 种基金the International S&T Cooperation Project of MOST of China (No. 2008CR1063)the Key Scientific and Technological Research Project of Shaanxi Province,China (Nos. 20092KC01-19 and 2008ZDGC-14)
文摘The intelligent structural health monitoring method, which uses a fiber Bragg grating （FBG） sensor, is a new approach in the field of civil engineering. However, it lacks a reliable FBG-based accelerometer for taking structural low frequency vibration measurements. In this letter, a fiextensional FBG-based accelerometer is proposed and demonstrated. The experimental results indicate that the natural frequency of the developed accelerometer is 16.7 Hz, with a high sensitivity of 410.7 pm/g. In addition, it has a broad and flat response over low frequencies ranging from 1 to 10 Hz. The natural frequency and sensitivity of the accelerometer can be tuned by adding mass to tailor the sensor performance to specific applications. Experimental results are presented to demonstrate the good performance of the proposed FBG-based accelerometer. These results show that the proposed accelerometer is satisfactory for low frequency vibration measurements.
基金Acknowledgment This work was supported by the National Natural Science Foundation of China （Grant Nos. 11474133 and 61235005）, Natural Science Foundation of Guangdong Province of China （No. 2014A030310419）, and the Guangzhou Key Collaborative Innovation Foundation of China （No.
文摘A dual-frequency distributed Bragg reflector （DBR） fiber laser based sensor is demonstrated for low-frequency vibration measurement through the Doppler effect. The response of the proposed sensor is quite linear and is much higher than that of a conventional accelerometer. The proposed sensor can work down to 1 Hz with high sensitivity. Therefore, the proposed sensor is very efficient in low-frequency vibration measurement.
