Effect of materials on the forming characteristics of laser-MIG hybrid welding process with filler wire for aluminum alloy

In this study,the test subjects included the aluminum alloys 2A14 and 5A06,as well as the welding wires ER2319 and ER5356,single laser welding,laser welding with filler wire,laser metal inert gas(laser-MIG)hybrid welding and laser-MIG hybrid welding with filler wire were carried out respectively to research the influence of aluminum alloy base material and welding wire on weld forming charac-teristics.The results show that:under the same test conditions,the penetration of the base material 5A06 is greater than that of 2A14,the maximum is about 51.3%,and the penetration filling ER5356 is greater than that of ER2319,the maximum is about 32.2%;for 2A14 alu-minum alloy,the penetration is basically unchanged after filling with ER5356,and there is a relatively large decrease after filling ER2319,the maximum is about 21.2%;for 5A06 aluminum alloy,the penetration decreases after filling both kinds of welding wire,the penetration achieved with filler wire ER2319 is lower than that of ER5356.At the same time,through the process of laser absorption in different metal materials,it was found that the differences in material composition led to different laser absorption rates,resulting in different energy utiliza-tion,which is an important reason for the correlation between aluminum alloy materials and laser-MIG hybrid welding with filler wire.

Stability of fiber laser-MIG hybrid welding of high strength aluminum alloy

The effect of fiber laser on MIG arc was investigated with 8 mm 7075-T6 high strength aluminum alloy as base material.The arc shape,droplet transfer form and electrical signal in the process of MIG welding and laser-MIG hybrid welding were analyzed.The stability of the hybrid welding process was evaluated by standard deviation analysis.The results show that with the increase of laser power,a large number of laser-induced plasma enters the arc column area,providing more conductive channels,which makes the heat of MIG arc more concentrated and the short circuit transition disappear.Due to the continuous effect of laser,the keyhole becomes a continuous electron emission source,and a stable cathode spot will be formed near the keyhole,which enhances the stability of MIG arc at the base current state.By using the method of standard deviation analysis,the voltage standard deviation of single MIG welding arc and laser-MIG hybrid arc within 4 seconds was calculated.The standard deviation of single MIG arc voltage was 1.05,and the standard deviation of MIG arc voltage in laser-MIG hybrid welding was 0.71–0.86,so the hybrid welding process was more stable.

CHARACTERISTICS OF DROPLET TRANSFER IN CO_2 LASER-MIG HYBRID WELDING WITH SHORTCIRCUITING MODE

LF6 aluminum alloy plates with 4.5 mm thickness are welded in this experiment. Welding is carried out by using the CO2 laser-MIG paraxial hybrid welding in fiat position. The experimental results indicate that the inherent droplet transfer cycle time of conventional MIG arc is changed due to the interaction between CO2 laser beam and MIG arc in the short-circuiting mode of laser-MIG hybrid welding. Because of the preheating action of CO2 laser to electrode and base material, the droplet transfer frequency of MIG arc is increased in the hybrid welding process. When laser power is increased to a certain degree, the droplet transfer frequency is decreased due to the effect of laser-induced keyhole. Furthermore, through analyzing the MIG welding current and arc voltage waveforms and the characteristics of droplet transfer in the hybrid welding process, the effect of laser energy and the action point between laser beam and arc on the frequency of droplet transfer and weld appearance is investigated in details.

Microstructure and mechanical properties of 6061 aluminum alloy laser-MIG hybrid welding joint

In this paper, 3 mm 6061 aluminum alloy sheets were welded by laser MIG hybrid welding. Based on the experiment, the best welding parameters were determined to ensure the penetration welding. The detailed microstructure,tensile and fatigue fracture morphology and surface fatigue damage of the welded joints were analyzed by optical microscope(OM), scanning electron microscope(SEM) and energy dispersive spectrometer(EDS). The results show that there are two main kinds of precipitates, one is the long Si rich precipitates at the grain boundaries, the other is the intragranular Cu rich precipitates. The tensile test results show that the tensile strength of the joint is 224 MPa, which is only 70.2% of the base metal. Through the analysis of tensile fracture, there are great differences in the formation of tensile dimple. In the tensile-tensile fatigue test with a stress rate of 0.1, the conditional fatigue limits of base metal and welded joint are 101.9 MPa and 54.4 MPa, respectively. By comparing the fatigue fracture of the welded joints under different stress amplitudes, it was found that the main factor leading to the fracture of the joint is porosity. Through further analysis of the pore defects, it was found that there are transgranular and intergranular propagation ways of microcracks in the pores, and the mixed propagation way was also found.

Mathematical analysis of the role of recoil pressure in weld pool dynamics during laser-MIG hybrid welding

A mathematical model was established to simulate the weld pool development and dynamic process in stationary iaser-MlG hybrid welding. Surface tension and buoyancy were considered to calculate liquid metal flow patter, moreover, typical phenomena of MIG welding, such as filler droplets impinging weld pool, electromagnetic force in the weld pool, and typical phenomena of laser beam welding, such as recoil pressure, Inverse Bremsstrahlung absorption, Fresnel absorption were all considered in the model. The laser beam and arc couple effect were introduced into this model by the plasma width during hybrid welding. The role of recoil pressure in the weld formation was discussed. Transient weld pool shape and complicated liquid metal velocity distribution from two kinds weld pool to an unified weld pool were calculated. The simulated weld bead geometry with consideration recoil pressure was in good agreement with experimental measurement.

Effect of Arc Energy on Morphology and Microstructure of Laser-MIG Hybrid Welded Joints of Invar Alloy

Laser-MIG hybrid welding experiments of 7 mm thick Invar alloy are carried out.The macro appearance of joints is observed and the influence of arc energy on the cross-section morphology is analyzed.The distribution of temperature field is simulated to explain the relationship between heat effect and microstructure.Besides,the average grain size of weld under different arc energies is quantitatively studied.The results indicate that welded joints with uniformity and good formation are obtained.The weld width and the weld seam area increase and the depth to width ratio decreases with the increase of arc heat input.The transition of columnar crystals to equiaxed crystals is observed from the fusion line to the weld center.It is found that the higher the arc energy,the coarser the columnar crystal.

Detection of butt weld of laser-MIG hybrid welding of thin-walled profile for high-speed train

Purpose–This study aims to solve the problem of weld quality inspection,for the aluminum alloy profile welding structure of high-speed train body has complex internal shape and thin plate thickness(2–4 mm),the conventional nondestructive testing method of weld quality is difficult to implement.Design/methodology/approach–In order to solve this problem,the ultrasonic creeping wave detection technology was proposed.The impact of the profile structure on the creeping wave detection was studied by designing profile structural test blocks and artificial simulation defect test blocks.The detection technology was used to test the actual welded test blocks,and compared with the results of X-ray test and destructive test(tensile test)to verify the accuracy of the ultrasonic creeping wave test results.Findings–It is indicated that that X-ray has better effect on the inspection of porosities and incomplete penetration defects.However,due to special detection method and protection,the detection speed is slow,which cannot meet the requirements of field inspection of the welding structure of aluminum alloy thin-walled profile for high-speed train body.It can be used as an auxiliary detection method for a small number of sampling inspection.The ultrasonic creeping wave can be used to detect the incomplete penetration welds with the equivalent of 0.25 mm or more,the results of creeping wave detection correspond well with the actual incomplete penetration defects.Originality/value–The results show that creeping wave detection results correspond well with the actual non-penetration defects and can be used for welding quality inspection of aluminum alloy thin-wall profile composite welding joints.It is recommended to use the echo amplitude of the 10 mm 30.2 mm 30.5 mm notch as the criterion for weld qualification.

Characteristic of laser-MIG hybrid welding with filling additional cold wire for aluminum alloy

The weld appearance, deposition rate, welding efficiency, stability of arc, laser keyhole characteristic, and weld property were studied by using a novel laser-MIG hybrid welding process with filling wire of aluminum alloy. The results were also compared with those by conventional laser-MIG hybrid welding process. It was found that with the suitable process parameters this novel welding process for aluminum alloy was stable and final weld bead had fine appearance. Compared to conventional laser-MIG hybrid welding process, during this novel welding process the stability of arc, the laser keyhole characteristic and the weld property were similar, while the keyhole cycle frequency and keyhole opening area had differences of 1.23% and 15.34%, respectively, and the welding efficiency increased by about 31% without increasing heat input.

The numerical simulation of laser-MIG hybrid welding for Invar alloy

Composites are widely applied to the manufacturing of aircraft in aviation. Forming of large-scale composite component in aircraft requires the corresponding mold with precise size. The laser-MIG hybrid welding has a significant advantage in the manufacturing of Invar mold for aircraft composites. This paper mainly introduces the application of the laser-MIG hybrid welding,and the distribution of thermal field and flow field on the Invar alloy laser-MIG hybrid three-layer welding is analyzed and discussed specifically.

Joint performance of CO2 laser-MIG hybrid welding 5083-H116 alloy

Laser-MIG hybrid welding process was dealt with 6 mm thick 5083Hl16 Al-Mg alloy plate in butt-joint configuration. Weld formation principle during hybrid welding was explained. The joint properties and microstructure characteristics of welded joints were analyzed by tensile tests, fractographs observed by optical microscopy and scanning electron microscopy （SEM）. Higher heat input could obtain better mechanical properties, and tensile strength and elongation reached 97.2%, 81% of the base metal, respectively. Fracture position traasited from fusion line to weld center in the higher heat input, and fracture location were only in the center of welded joints for the heat input relatively small.

Study of the Laser-MIG Hybrid Welded Al-Mg Alloy

The technology of laser-MIG hybrid welding is hotspot in welding researched field at present.It can improve the velocity of the welding,reduce the distortion of the welding,optimize the structure of the welding joint and etc..The 5052 aluminum alloy of the 10mm thick was welded by the laser-MIG hybrid welding.The structure,the alloy elements profile and the mechanical property of the welded joint are researched by the optical microscope,SEM,sclerometer and etc..The results showed:The medium thick Al alloy was welded in high speed by the laser-MIG hybrid welding.The appearance of the welding joint is well.The weld joint and the weld interface are fine.The intenerate region in the welding joint is small.The tensile strength in welding joint has achieved 94.4% of that in base metal.

Microstructure and mechanical performance of AZ31/6061 lap joints welded by laser-TIG hybrid welding with Zn-Al alloy filler metal

A series of Zn-xAl(x=0-35 wt.%)alloy filler metals were designed to join AZ31 Mg alloy to 6061 Al alloy by laser-TIG hybrid welding.The effect of Al content on the wettability of filler metals,microstructure evolution and strength of joint was investigated.The results indicated that the strength of joints was improved with the increase of Al content in filler metals.When Zn-15Al filler was used,the ultimate fracture load reached the maximum of 1475.3 N/cm,which was increased by 28%than that with pure Zn filler.The reason is that the Al element acts as a"reaction depressant"in filler metal,which contributes to inhibiting the dissolution of Mg base metal and the Mg-Zn reaction.The addition of appropriate quantity of Al element promoted the precipitation of Al-rich solid solution instead of Zn solid solution.The MgZn_(2) IMCs have lower lattice mismatch with Al solid solution than Zn solid solution,thus the strength of joints is improved.However,the excessive addition of Al caused the formation of brittle Mg32(Al,Zn)49 ternary compounds,leading to the deterioration of joint performance.

Beam oscillating parameters on pore inhibition,recrystallization and grain boundary characteristics of laser-arc hybrid welded AZ31 magnesium alloy

Oscillating laser-arc hybrid welding of AZ31B magnesium alloy was carried out,the effects of beam oscillation parameters on pore inhibition,microstructure,grain boundary characteristics and tensile properties were investigated.The results showed that the pore formation can be inhibited with oscillating frequency higher than 75 Hz and radius smaller than 0.5 mm.The columnar grains neighboring the fusion line can be broken by the beam oscillation behavior,while the grain growth was promoted with the increase of frequency or radius.It should be noted that the coincidence site lattice(CSL)boundaries were mainlyΣ13b andΣ29 boundaries,which were contributed by{10■2}tensile twins and{11■2}compression twins,respectively.The total fraction of CSL boundaries reached maximum at radius of 0.25 mm and frequency of 75 Hz,which was also confirmed as the optimized parameters.In this case,the elongation rate increased up to 13.2%,12.8%higher than that of the weld without beam oscillation.Finally,the pore formation and inhibition mechanisms were illustrated according to the state of melt flow and keyhole formation,the abnormal growth was discussed basing on secondary recrystallization,and the relationship among the pore formation,grain size,boundary characteristics and weld toughness were finally established.

Microstructure homogeneity and mechanical properties of laser-arc hybrid welded AZ31B magnesium alloy

Laser-arc hybrid welding of AZ31B magnesium alloy was carried out,the effects of welding parameters on weld formation,microstructure homogeneity and mechanical properties were investigated.The results showed that laser-arc hybrid welding was beneficial to improve the weld formation of magnesium alloy by inhibiting the defect of undercut and pores.The weld microstructure was mainly columnar grains neighboring the fusion line and equiaxed grains at the weld center.It was interesting that the grain size at the upper arc zone was smaller than that at the lower laser zone,with the difference mainly affected by laser power rather than welding current and welding speed.The welding parameters were optimized as laser power of 3.5 kW,welding current of 100 A and welding speed of 1.5 m/min.In this case,the weld was free of undercut and pores,and the tensile strength and elongation rate reached 252 MPa and 11.2%,respectively.Finally,the microstructure homogeneity was illustrated according to the heat distribution,and the evolution law of tensile properties was discussed basing on the weld formation and microstructure characteristics.

Microstructures and properties of welded joint of aluminum alloy to galvanized steel by Nd:YAG laser + MIG arc hybrid brazing-fusion welding

According to the differences in melting point between aluminum alloy and steel, 6013-T4 aluminum alloy was joined to galvanized steel by large spot Nd：YAG laser ＋ MIG arc hybrid brazing-fusion welding with ER4043（AlSi5） filler wire. The microstructures and mechanical properties of the brazed-fusion welded joint were investigated. The joint is divided into two parts of fusion weld and brazed seam. There is a zinc-rich zone at fusion weld toe, which consists of α（Al）-Zn solid solution and Al-Zn eutectic. The brazed seam is the Fe-Al intermetallic compounds （IMCs） layer of 2-4μm in thickness, and the IMCs include FeAl2, Fe2Al5 and Fe4Al13. FeAl2 and Fe2Al5 are located in the compact reaction layer near the steel side, and Fe4Al13 with tongue shape or sawtooth shape grows towards the fusion weld. The tensile strength of the joint firstly increases and then decreases as the welding current and laser power increase, the highest tensile strength can be up to 247.3 MPa, and the fracture usually occurs at fusion zone of the fusion weld. The hardness is the highest at the brazed seam because of hard Fe-Al IMCs, and gradually decreases along the fusion weld and galvanized steel, respectively.

Laser-weldable Si_p-SiC_p/Al hybrid composites with bilayer structure for electronic packaging

Laser-weldable Sip-SiCp/Al hybrid composites with high volume fraction （60%-65%） of SiC reinforcement were fabricated by compression moulding and vacuum gas pressure infiltration technology. Microscopic observation displayed that the Sip-SiCp/Al hybrid composites with bilayer structure were compact without gas pores and the intergradation between Sip/Al layer and SiCp/Al layer was homogeneous and continuous. Further investigation revealed that the Sip-SiCp/Al hybrid composites possessed low density （2.96 g/cm^3）, high gas tightness （1.0 mPa·cm^3）/s）, excellent thermal management function as a result of high thermal conductivity （194 W/（m·K） and low coefficient of thermal expansion （7.0×10^-6 K-1）. Additionally, Sip-SiCp/Al hybrid composites had outstanding laser welding adaptability, which is significantly important for electronic packaging applications. The gas tightness of components after laser welding （48 mPa·cm^3）/s） can well match the requirement of advanced electronic packaging. Several kinds of these precision components passed tests and were put into production.

Laser-pulsed MIG hybrid welding technology of A6N01S aluminum alloy

Welding research of A6N01S-T5 aluminum alloy profile for high-speed train was done by using laser-MIG hybrid welding and MIG welding individually. And the weld appearance,welding distortion,mechanical properties of the joints and microstructures were analyzed. The test results demonstrated that high-efficient welding for the profile can be achieved by using laser-MIG hybrid welding,the speed of which can be over 3. 0 m/min. The processing had a good gap bridging ability,even if the gap of the butt joint was up to 2. 0 mm,a good weld appearance can also be got. While the hybrid welding speed was greater than 2. 5 m/min,the welding distortion of the laser-tandem MIG hybrid joints was just about 33% of that of the MIG joints,but the welding efficiency was over 3 times of MIG welding. And tensile strength of the hybrid joints was 85% of that of A6N01S-T5 base metal,9% higher than that of the MIG joints. Fatigue properties was tested individually with pulsed tensile fatigue method in the condition of 1 × 10~7 lifetime. The test results demonstrated that the fatigue strength of the joints was a little lower than that of base material,which could be up to 115 MPa. But the fatigue strength of hybrid welding joints was 107. 5 MPa,which was 23% higher than 87 MPa of MIG welding joints.

Research on laser-arc hybrid welding technology for long-distance pipeline construction

In recent years, the research on pipeline laser-arc hybrid welding technology has been the important and difficult in the field of welding all over the world. China Petroleum Pipeline Research Institute Co. Ltd. has firstly developed pipeline laser-arc hybrid welding system in China, and executed the welding tests based on X70/X80 steel. Preliminary experiment results showed that hybrid welding could meet the requirements of related standards such as API1104,ASME,etc., the mechanical properties of girth seam are qualified in the case that there were no internal defects. With the development of high-power fiber laser and the continuous improvement of welding equipment, laser-arc hybrid welding technology for pipeline field welding will be available soon.

Microstructure and mechanical properties of the joint of 6061 aluminum alloy by plasma-MIG hybrid welding

Plasma-MIG {metal inert gas arc welding） hybrid welding of aluminum alloy with 6 mm thickness using ER5356 welding wire was carried out. The microstructures and mechanical properties of the welded joint were investigated by optical microscopy, X-ray diffraction （XRD） , energy dispersive spectroscopy （EDS） , tensile test, hardness test and scanning electron microscope （ SEM） were used to judge the type of tensile fracture. The results showed that the tensile strength of welded joint was 142 MPa which was 53. 6% o f the strength o f the base metal. The welding seam zone was characterized by dendritic structure. In the fusion zone, the columnar grains existed at one side of the welding seam. The fibrous organization was found in the base metal, and also in the heat affected zone （HAZ） where the recrystallization occurred. The HAZ was the weakest position of the welded joint due to the coarsening of Mg2Si phase. The type of tensile fracture was ductile fracture.

MODEL OF LASER-TIG HYBRID WELDING HEAT SOURCE

The welding mechanism of laser-TIG hybrid welding process is analyzed. Withthe variation of arc current, the welding process is divided into two patterns: deep-penetrationwelding and heat conductive welding. The heat flow model of hybrid welding is presented. As todeep-penetration welding, the heat source includes a surface heat flux and a volume heat flux. Theheat source of heat conductive welding is composed of two Gaussian distribute surface heat sources.With this heat source model, a temperature field is calculated. The finite element code MARC isemployed for this purpose. The calculation results show a good agreement with the experimental data.