Micro milling is a flexible and economical method to fabricate micro components with three-dimensional geometry features over a wide range of engineering materials. But the surface roughness and micro topography alway...Micro milling is a flexible and economical method to fabricate micro components with three-dimensional geometry features over a wide range of engineering materials. But the surface roughness and micro topography always limit the performance of the machined micro components. This paper presents a surface generation simulation in micro end milling considering both axial and radial tool runout. Firstly, a surface generation model is established based on the geometry of micro milling cutter. Secondly, the influence of the runout in axial and radial directions on the surface generation are investigated and the surface roughness prediction is realized. It is found that the axial runout has a significant influence on the surface topography generation. Furthermore, the influence of axial runout on the surface micro topography was studied quantitatively, and a critical axial runout is given for variable feed per tooth to generate specific surface topography. Finally, the proposed model is validated by means of experiments and a good correlation is obtained. The proposed surface generation model o ers a basis for designing and optimizing surface parameters of functional machined surfaces.展开更多
Structure design and fabricating methods of three-dimensional (3D) artificial spherical compound eyes have been researched by many scholars. Micro-nano optical manufacturing is mostly used to process 3D artificial c...Structure design and fabricating methods of three-dimensional (3D) artificial spherical compound eyes have been researched by many scholars. Micro-nano optical manufacturing is mostly used to process 3D artificial compound eyes. However, spherical optical compound eyes are less at optical performance than the eyes of insects, and it is difficult to further improve the imaging quality of compound eyes by means of micro-nano optical manufacturing. In this research, nonhomogeneous aspheric compound eyes (ACEs) are designed and fabricated. The nonhomogeneous aspheric structure is applied to calibrate the spherical aberration. Micro milling with advantages in processing three-dimensional micro structures is adopted to manufacture ACEs. In order to obtain ACEs with high imaging quality, the tool paths are optimized by analyzing the influence factors consisting of interpolation allowable error, scallop height and tool path pattern. In the experiments, two kinds of ACEs are manufactured by micro-milling with different too path patterns and cutting parameter on the miniature precision five-axis milling machine tool. The experimental results indicate that the ACEs of high surface quality can be achieved by circularly milling small micro-lens individually with changeable cutting depth. A prototype of the aspheric compound eye (ACE) with surface roughness (Ra) below 0.12 p.m is obtained with good imaging performance. This research ameliorates the imaging quality of 3D artificial compound eyes, and the proposed method of micro-milling can improve surface processing quality of compound eyes.展开更多
Surface modification,as a promising approach to improve biocompatibility of biomaterials,has captured extensive close attention among many researchers.Here,micro-milling technology was used in constructing pyramid mic...Surface modification,as a promising approach to improve biocompatibility of biomaterials,has captured extensive close attention among many researchers.Here,micro-milling technology was used in constructing pyramid micro-structures on the surface of Ti-6Al-4Vimplant.Cutting parameters,including spindle speed,feed rate and depth of cut,were optimized to control the generation of burrs.In addition,low melting point alloy was selected to extend the boundary of the workpiece as supporting material to prevent the generation of top burrs.The surface topographies were characterized using scanning electron microscope and laser scanning microscope.Results showed that the dimension of burrs decreased with the decrease of depth of cut,and the size of burrs decreased with the increase of feed rate.Moreover,burrs nearly not appeared on both sides of the micro-grooves machined with low melting point alloy(LMPA)coating.Pyramid micro-structure on the workpiece surface was built successfully by combining optimized cutting parameters(S=35kr/min,Vf=60mm/min,ap=5μm)and LMPA coating.展开更多
Tool wear and breakage of the micro-milling tool is an important problem for high speed machining of hardened steel die and mould. Dry milling of S136 hardened steel is carried out using TiA1N coated carbide micro-end...Tool wear and breakage of the micro-milling tool is an important problem for high speed machining of hardened steel die and mould. Dry milling of S136 hardened steel is carried out using TiA1N coated carbide micro-end mill (Ф2 mm). The effect of cutting speed, feed per tooth and radial depth of cut on cutting force is analyzed. Cutting parameters adapting to dry machining and strategy optimized for higher rate of material removal with lower cutting force are attained. Results of SEM observation show that the main failure patterns of micro-end mill are breakage of tool tip, wear and drop-off of surface coating, micro-chipping, and breakage of flank.展开更多
Short tool life and rapid tool wear in micromachining of hard-to-machine materials remain a barrier to the process being economically viable. In this study, standard procedures and conditions set by the ISO for tool l...Short tool life and rapid tool wear in micromachining of hard-to-machine materials remain a barrier to the process being economically viable. In this study, standard procedures and conditions set by the ISO for tool life testing in milling were used to analyze the wear of tungsten carbide micro-end-milling tools through slot milling conducted on titanium alloy Ti-6 Al-4 V. Tool wear was characterized by flank wear rate,cutting-edge radius change, and tool volumetric change. The effect of machining parameters, such as cutting speed and feedrate, on tool wear was investigated with reference to surface roughness and geometric accuracy of the finished workpiece. Experimental data indicate different modes of tool wear throughout machining, where nonuniform flank wear and abrasive wear are the dominant wear modes. High cutting speed and low feedrate can reduce the tool wear rate and improve the tool life during micromachining.However, the low feedrate enhances the plowing effect on the cutting zone, resulting in reduced surface quality and leading to burr formation and premature tool failure. This study concludes with a proposal of tool rejection criteria for micro-milling of Ti-6 Al-4 V.展开更多
Taking the minimum chip thickness effect,cutter deflection,and spindle run-out into account,a micro milling force model and a method to determine the optimal micro milling parameters were developed.The micro milling f...Taking the minimum chip thickness effect,cutter deflection,and spindle run-out into account,a micro milling force model and a method to determine the optimal micro milling parameters were developed.The micro milling force model was derived as a function of the cutting coefficients and the instantaneous projected cutting area that was determined based on the machining parameters and the rotation trajectory of the cutter edges.When an allowable micro cutter deflection is defined,the maximum allowable cutting force can be determined.The optimal machining parameters can then be computed based on the cutting force model for better machining efficiency and accuracy.To verify the proposed cutting force model and the method to determine the optimal cutting parameters,micro-milling experiments were conducted,and the results show the feasibility and effectiveness of the model and method.展开更多
Based on microscope and image processing, a new method of auto tool setting for micro milling was presented. Firstly, a realtime image of tool setting area was obtained by microscope and CCD camera, then image process...Based on microscope and image processing, a new method of auto tool setting for micro milling was presented. Firstly, a realtime image of tool setting area was obtained by microscope and CCD camera, then image processing was carried out on this image and the gap between the tool and workpiece was calculated. The gap measurement was sent to motion controlling card to make the tool approach to the surface of workpiece. These steps were repeated until the gap is zero, which means that tool setting was finished. Moreover, a reliability verification test was conducted. Results indicated that the precision of tool setting is satisfactory.展开更多
The quality factor(Q factor)is a crucial performance parameter for resonators.In this paper,a novel release method for highquality micro fused silica shell resonators with teeth-like tines with good surface morphology...The quality factor(Q factor)is a crucial performance parameter for resonators.In this paper,a novel release method for highquality micro fused silica shell resonators with teeth-like tines with good surface morphology is proposed.This method is based on femtosecond laser-assisted chemical etching.First,the optimal energy range of femtosecond laser modification is obtained through mechanism analysis.Second,the optimal parameters for a straight line and arc pattern are determined by optimizing the average output power,processing speed,and processing spacing.The results demonstrate why edge breakage in rounded corners is easy under different parameters.Finally,according to these conclusions,the processing is performed on a micro fused silica shell resonator with a Q factor exceeding 6 million.In addition,subsurface damage is rare throughout the fabrication process,and the surface roughness of the released cross section reaches the nanometer level.The improved Q factor helps suppress mechanical thermal noise and reduce zero bias and zero bias drift,constituting the primary method for enhancing the performance of the resonant gyroscope.展开更多
Micro milling is a machining method of high precision and efficiency for micro components and features.In order to study the surface quality of single crystal materials in micro milling,the two-edged cemented carbide ...Micro milling is a machining method of high precision and efficiency for micro components and features.In order to study the surface quality of single crystal materials in micro milling,the two-edged cemented carbide tool milling cutter with 0.4 mm diameter was used,and the orthogonal experiment was completed on the micro-milling of single crystal aluminum material.Through the analysis of statistical results,the primary and secondary factor which impacting on surface quality were found as follows:spindle speed,feed rate,milling depth.The ideal combination of optimized process parameters were obtained,when the spindle speed was 36000 r/min,the milling depth was 10μm,the feed rate was 80μm/s,which made the milling surface roughness is 0.782μm and minimal.Single crystal materials removal mechanism were revealed,and the influence of cutting parameters on micro-milling surface were discussed,the reason of tool wear was analyzed.Those provide a certain theoretical and experimental basis for micro milling of single crystal materials.展开更多
Micro milling has many advantages in fabricating three-dimensional(3D) structure in micrometer scale. The micro milling machine tool with high positioning accuracy is of great importance for getting micro structure wi...Micro milling has many advantages in fabricating three-dimensional(3D) structure in micrometer scale. The micro milling machine tool with high positioning accuracy is of great importance for getting micro structure with high profile precision and good surface quality. Meanwhile, the method of position error compensation is a good way to improve the accuracy of the micro milling machine tools. In this paper,a software method is adopted to compensate the positioning error and improve the positioning accuracy. According to error cancellation theory,the compensation values are generated and compensation tables are built to adjust the positioning error in the NC system based on Industrial Motion and Automation Control( IMAC). The positioning accuracy of linear motor is ± 0. 3 μm without backlash after compensation. In order to verify the effectiveness of compensation on the machining performance,concave spherical surfaces are processed on the micro milling machine tool. The experimental results show that the profile radius error of the spherical surface machined with compensation decreases more than 60%.展开更多
The applications of micro-machining have increased drastically in the last ten years. However, tools with less than 1mm diameter using for micro-mills have very short and unpredictable life when they are used to cut h...The applications of micro-machining have increased drastically in the last ten years. However, tools with less than 1mm diameter using for micro-mills have very short and unpredictable life when they are used to cut hard metals. In this study, preliminary design of experiment (DOE) test program was conducted to investigate and identify the factors affecting tool wear at the micro-scale with hard material. Analysis of variance (ANOVA) and Taguchi method were efficient to determine appropriate cutting condition and the effect of parameters. A simple model was also developed to predict the width of slots on the workpiece along the cutting length. The obtained results can provide the basic guidelines for parameter setting of micro-end-milling with hard material.展开更多
Based on the study of existing typical micro-milling tools and the actual demand for micro-milling tools, the P3 design principle and design flow for ultra-hard micro-milling tool were introduced to give basic guidanc...Based on the study of existing typical micro-milling tools and the actual demand for micro-milling tools, the P3 design principle and design flow for ultra-hard micro-milling tool were introduced to give basic guidance for the optimization of micro-milling tools. Then, according to the P3 design flow, the manufacturing process of polycrystalline diamond(PCD) micro-milling tool was proposed, and the PCD micro-milling tool with diameter of 0.5 mm was developed. Finally, the micro-milling test on the slot was carried out to study the milling performance of PCD micromilling tool.展开更多
A human face with complex 3D structure is machined with a modified fix-length compensation method in this paper.The fast development of MEMS (Micro Electromechanical Systems) has strongly enhanced the application of n...A human face with complex 3D structure is machined with a modified fix-length compensation method in this paper.The fast development of MEMS (Micro Electromechanical Systems) has strongly enhanced the application of new harder work materials.As a low cost,flexible,good repeatable machining process with negligible process forces,micro-EDM milling is well suited for freeform metallic micro structures.A major problem in micro-EDM milling of complex 3D structure is the electrode wear.A new CAM system based on the UG software platform is developed in order to get good accuracy and higher efficiency.A correction coefficient is introduced and deduced for the modified fix-length compensation method.Using this method a human face with complex 3D stricter is machined successfully by micro-EDM milling.展开更多
Vibration-assisted machining(VAM) has the advantages of extending tool life,reducing cutting force and improving the surface finish.Implementation of vibration assistance with high frequency and amplitude is still a c...Vibration-assisted machining(VAM) has the advantages of extending tool life,reducing cutting force and improving the surface finish.Implementation of vibration assistance with high frequency and amplitude is still a challenge,especially for a micro-milling process.In this paper,a new 2D vibration stage for vibration-assisted micro-milling is developed.The kinematics of the milling process with vibration assistance is modeled,and the effects of vibration parameters on the periodic tool-workpiece separation(TWS) is analyzed.The structure of the vibration stage is designed with flexure hinges,and two piezoelectric actuators are used to drive the stage in two directions.An amplifier is integrated into the vibration stage,and the dynamics of the whole vibration system are identified and analyzed.Micro-milling experiments are conducted to determine the effects of vibration assistance on cutting force and surface quality.展开更多
In this article, the results obtained from a study carried out on the some elements-incorporated diamond-like carbon (DLC) films are reported. All the films were deposited using plasma-based ion implantation (PBII) te...In this article, the results obtained from a study carried out on the some elements-incorporated diamond-like carbon (DLC) films are reported. All the films were deposited using plasma-based ion implantation (PBII) technique. The deposited films were annealed at 400℃, 650℃ and 900℃ in an air atmosphere for 1 hour. The effects of adding hydrogen, silicon/oxygen and silicon/nitrogen into the DLC film on chemical composition, friction coefficient and corrosion resistance were investigated. The films coated micro end mills performance was also assessed. The results indicate that all the films showed almost constant atomic contents of C, Si, O and N until annealing at 400℃. However, the films were completely destroyed at 650℃ with the increased Si and O contents, while the C content decreased. The incorporation of silicon/oxygen and silicon/nitrogen into the DLC exhibited lower values of friction coefficients than the hydrogenated DLC (DLC and H-DLC) before and after annealing at 400℃, whereas all the films presented the same values of friction coefficients after annealing at 650℃ due to the completely destroy of the films. Furthermore, the incorporation of silicon/nitrogen into the DLC also exhibited better corrosion resistance and unbroken micro end mills performance on their surfaces. Thus, the incorporation of silicon/nitrogen into the DLC film can be considered beneficial in improving the micro end mills performance.展开更多
基金Supported by Engineering and Physical Sciences Research Council(Grant No.EP/M020657/1)National Natural Science Foundation of China(Grant No.51505107)Project of Natural Scientific Research Innovation Foundation in Harbin Institute of Technology(Grant No.HIT.NSRIF.2017029)
文摘Micro milling is a flexible and economical method to fabricate micro components with three-dimensional geometry features over a wide range of engineering materials. But the surface roughness and micro topography always limit the performance of the machined micro components. This paper presents a surface generation simulation in micro end milling considering both axial and radial tool runout. Firstly, a surface generation model is established based on the geometry of micro milling cutter. Secondly, the influence of the runout in axial and radial directions on the surface generation are investigated and the surface roughness prediction is realized. It is found that the axial runout has a significant influence on the surface topography generation. Furthermore, the influence of axial runout on the surface micro topography was studied quantitatively, and a critical axial runout is given for variable feed per tooth to generate specific surface topography. Finally, the proposed model is validated by means of experiments and a good correlation is obtained. The proposed surface generation model o ers a basis for designing and optimizing surface parameters of functional machined surfaces.
基金Supported by National Natural Science Foundation of China(Grant No.50935003)National Numerical Control Major Projects of China(Grant No.2013ZX04001000215)
文摘Structure design and fabricating methods of three-dimensional (3D) artificial spherical compound eyes have been researched by many scholars. Micro-nano optical manufacturing is mostly used to process 3D artificial compound eyes. However, spherical optical compound eyes are less at optical performance than the eyes of insects, and it is difficult to further improve the imaging quality of compound eyes by means of micro-nano optical manufacturing. In this research, nonhomogeneous aspheric compound eyes (ACEs) are designed and fabricated. The nonhomogeneous aspheric structure is applied to calibrate the spherical aberration. Micro milling with advantages in processing three-dimensional micro structures is adopted to manufacture ACEs. In order to obtain ACEs with high imaging quality, the tool paths are optimized by analyzing the influence factors consisting of interpolation allowable error, scallop height and tool path pattern. In the experiments, two kinds of ACEs are manufactured by micro-milling with different too path patterns and cutting parameter on the miniature precision five-axis milling machine tool. The experimental results indicate that the ACEs of high surface quality can be achieved by circularly milling small micro-lens individually with changeable cutting depth. A prototype of the aspheric compound eye (ACE) with surface roughness (Ra) below 0.12 p.m is obtained with good imaging performance. This research ameliorates the imaging quality of 3D artificial compound eyes, and the proposed method of micro-milling can improve surface processing quality of compound eyes.
基金supported by the National Natural Science Foundations of China(Nos.51175306,51425503)the Tai Shan Scholar Foundation,the Fundamental Research Funds for the Central Universities(No.2014JC020)the Opening fund of State Key Laboratory of Nonlinear Mechanics
文摘Surface modification,as a promising approach to improve biocompatibility of biomaterials,has captured extensive close attention among many researchers.Here,micro-milling technology was used in constructing pyramid micro-structures on the surface of Ti-6Al-4Vimplant.Cutting parameters,including spindle speed,feed rate and depth of cut,were optimized to control the generation of burrs.In addition,low melting point alloy was selected to extend the boundary of the workpiece as supporting material to prevent the generation of top burrs.The surface topographies were characterized using scanning electron microscope and laser scanning microscope.Results showed that the dimension of burrs decreased with the decrease of depth of cut,and the size of burrs decreased with the increase of feed rate.Moreover,burrs nearly not appeared on both sides of the micro-grooves machined with low melting point alloy(LMPA)coating.Pyramid micro-structure on the workpiece surface was built successfully by combining optimized cutting parameters(S=35kr/min,Vf=60mm/min,ap=5μm)and LMPA coating.
文摘Tool wear and breakage of the micro-milling tool is an important problem for high speed machining of hardened steel die and mould. Dry milling of S136 hardened steel is carried out using TiA1N coated carbide micro-end mill (Ф2 mm). The effect of cutting speed, feed per tooth and radial depth of cut on cutting force is analyzed. Cutting parameters adapting to dry machining and strategy optimized for higher rate of material removal with lower cutting force are attained. Results of SEM observation show that the main failure patterns of micro-end mill are breakage of tool tip, wear and drop-off of surface coating, micro-chipping, and breakage of flank.
基金the Engineering and Physical Sciences Research Council (EP/M020657/1) for the support for this work
文摘Short tool life and rapid tool wear in micromachining of hard-to-machine materials remain a barrier to the process being economically viable. In this study, standard procedures and conditions set by the ISO for tool life testing in milling were used to analyze the wear of tungsten carbide micro-end-milling tools through slot milling conducted on titanium alloy Ti-6 Al-4 V. Tool wear was characterized by flank wear rate,cutting-edge radius change, and tool volumetric change. The effect of machining parameters, such as cutting speed and feedrate, on tool wear was investigated with reference to surface roughness and geometric accuracy of the finished workpiece. Experimental data indicate different modes of tool wear throughout machining, where nonuniform flank wear and abrasive wear are the dominant wear modes. High cutting speed and low feedrate can reduce the tool wear rate and improve the tool life during micromachining.However, the low feedrate enhances the plowing effect on the cutting zone, resulting in reduced surface quality and leading to burr formation and premature tool failure. This study concludes with a proposal of tool rejection criteria for micro-milling of Ti-6 Al-4 V.
基金Project(NSC98-2221-E-033-047)supported by National Science Council
文摘Taking the minimum chip thickness effect,cutter deflection,and spindle run-out into account,a micro milling force model and a method to determine the optimal micro milling parameters were developed.The micro milling force model was derived as a function of the cutting coefficients and the instantaneous projected cutting area that was determined based on the machining parameters and the rotation trajectory of the cutter edges.When an allowable micro cutter deflection is defined,the maximum allowable cutting force can be determined.The optimal machining parameters can then be computed based on the cutting force model for better machining efficiency and accuracy.To verify the proposed cutting force model and the method to determine the optimal cutting parameters,micro-milling experiments were conducted,and the results show the feasibility and effectiveness of the model and method.
基金Supported by National Natural Science Foundation of China (No. 50935003)
文摘Based on microscope and image processing, a new method of auto tool setting for micro milling was presented. Firstly, a realtime image of tool setting area was obtained by microscope and CCD camera, then image processing was carried out on this image and the gap between the tool and workpiece was calculated. The gap measurement was sent to motion controlling card to make the tool approach to the surface of workpiece. These steps were repeated until the gap is zero, which means that tool setting was finished. Moreover, a reliability verification test was conducted. Results indicated that the precision of tool setting is satisfactory.
基金supported by the National Natural Science Foundation of China Regional Innovation and Development Joint Fund Key Support Project(Grant No.U21A20505)the National Natural Science Foundation of China(Grant Nos.62204261 and 52205613)。
文摘The quality factor(Q factor)is a crucial performance parameter for resonators.In this paper,a novel release method for highquality micro fused silica shell resonators with teeth-like tines with good surface morphology is proposed.This method is based on femtosecond laser-assisted chemical etching.First,the optimal energy range of femtosecond laser modification is obtained through mechanism analysis.Second,the optimal parameters for a straight line and arc pattern are determined by optimizing the average output power,processing speed,and processing spacing.The results demonstrate why edge breakage in rounded corners is easy under different parameters.Finally,according to these conclusions,the processing is performed on a micro fused silica shell resonator with a Q factor exceeding 6 million.In addition,subsurface damage is rare throughout the fabrication process,and the surface roughness of the released cross section reaches the nanometer level.The improved Q factor helps suppress mechanical thermal noise and reduce zero bias and zero bias drift,constituting the primary method for enhancing the performance of the resonant gyroscope.
文摘Micro milling is a machining method of high precision and efficiency for micro components and features.In order to study the surface quality of single crystal materials in micro milling,the two-edged cemented carbide tool milling cutter with 0.4 mm diameter was used,and the orthogonal experiment was completed on the micro-milling of single crystal aluminum material.Through the analysis of statistical results,the primary and secondary factor which impacting on surface quality were found as follows:spindle speed,feed rate,milling depth.The ideal combination of optimized process parameters were obtained,when the spindle speed was 36000 r/min,the milling depth was 10μm,the feed rate was 80μm/s,which made the milling surface roughness is 0.782μm and minimal.Single crystal materials removal mechanism were revealed,and the influence of cutting parameters on micro-milling surface were discussed,the reason of tool wear was analyzed.Those provide a certain theoretical and experimental basis for micro milling of single crystal materials.
基金Sponsored by the National Natural Science Foundation of China(Grant No.50935003)
文摘Micro milling has many advantages in fabricating three-dimensional(3D) structure in micrometer scale. The micro milling machine tool with high positioning accuracy is of great importance for getting micro structure with high profile precision and good surface quality. Meanwhile, the method of position error compensation is a good way to improve the accuracy of the micro milling machine tools. In this paper,a software method is adopted to compensate the positioning error and improve the positioning accuracy. According to error cancellation theory,the compensation values are generated and compensation tables are built to adjust the positioning error in the NC system based on Industrial Motion and Automation Control( IMAC). The positioning accuracy of linear motor is ± 0. 3 μm without backlash after compensation. In order to verify the effectiveness of compensation on the machining performance,concave spherical surfaces are processed on the micro milling machine tool. The experimental results show that the profile radius error of the spherical surface machined with compensation decreases more than 60%.
文摘The applications of micro-machining have increased drastically in the last ten years. However, tools with less than 1mm diameter using for micro-mills have very short and unpredictable life when they are used to cut hard metals. In this study, preliminary design of experiment (DOE) test program was conducted to investigate and identify the factors affecting tool wear at the micro-scale with hard material. Analysis of variance (ANOVA) and Taguchi method were efficient to determine appropriate cutting condition and the effect of parameters. A simple model was also developed to predict the width of slots on the workpiece along the cutting length. The obtained results can provide the basic guidelines for parameter setting of micro-end-milling with hard material.
基金Supported by the National Natural Science Foundation of China(No.50935003)Science and Technology Support Project of Jiangsu Province,China(No.BE2012172)
文摘Based on the study of existing typical micro-milling tools and the actual demand for micro-milling tools, the P3 design principle and design flow for ultra-hard micro-milling tool were introduced to give basic guidance for the optimization of micro-milling tools. Then, according to the P3 design flow, the manufacturing process of polycrystalline diamond(PCD) micro-milling tool was proposed, and the PCD micro-milling tool with diameter of 0.5 mm was developed. Finally, the micro-milling test on the slot was carried out to study the milling performance of PCD micromilling tool.
基金Funded by the National Natural Science Foundation of China (No.50635040)
文摘A human face with complex 3D structure is machined with a modified fix-length compensation method in this paper.The fast development of MEMS (Micro Electromechanical Systems) has strongly enhanced the application of new harder work materials.As a low cost,flexible,good repeatable machining process with negligible process forces,micro-EDM milling is well suited for freeform metallic micro structures.A major problem in micro-EDM milling of complex 3D structure is the electrode wear.A new CAM system based on the UG software platform is developed in order to get good accuracy and higher efficiency.A correction coefficient is introduced and deduced for the modified fix-length compensation method.Using this method a human face with complex 3D stricter is machined successfully by micro-EDM milling.
基金supported by NSERC-Discovery FundsRGPIN-2018-04911partly supported by China Scholarship Council.
文摘Vibration-assisted machining(VAM) has the advantages of extending tool life,reducing cutting force and improving the surface finish.Implementation of vibration assistance with high frequency and amplitude is still a challenge,especially for a micro-milling process.In this paper,a new 2D vibration stage for vibration-assisted micro-milling is developed.The kinematics of the milling process with vibration assistance is modeled,and the effects of vibration parameters on the periodic tool-workpiece separation(TWS) is analyzed.The structure of the vibration stage is designed with flexure hinges,and two piezoelectric actuators are used to drive the stage in two directions.An amplifier is integrated into the vibration stage,and the dynamics of the whole vibration system are identified and analyzed.Micro-milling experiments are conducted to determine the effects of vibration assistance on cutting force and surface quality.
文摘In this article, the results obtained from a study carried out on the some elements-incorporated diamond-like carbon (DLC) films are reported. All the films were deposited using plasma-based ion implantation (PBII) technique. The deposited films were annealed at 400℃, 650℃ and 900℃ in an air atmosphere for 1 hour. The effects of adding hydrogen, silicon/oxygen and silicon/nitrogen into the DLC film on chemical composition, friction coefficient and corrosion resistance were investigated. The films coated micro end mills performance was also assessed. The results indicate that all the films showed almost constant atomic contents of C, Si, O and N until annealing at 400℃. However, the films were completely destroyed at 650℃ with the increased Si and O contents, while the C content decreased. The incorporation of silicon/oxygen and silicon/nitrogen into the DLC exhibited lower values of friction coefficients than the hydrogenated DLC (DLC and H-DLC) before and after annealing at 400℃, whereas all the films presented the same values of friction coefficients after annealing at 650℃ due to the completely destroy of the films. Furthermore, the incorporation of silicon/nitrogen into the DLC also exhibited better corrosion resistance and unbroken micro end mills performance on their surfaces. Thus, the incorporation of silicon/nitrogen into the DLC film can be considered beneficial in improving the micro end mills performance.