Damage Evolution of Ballastless Track Concrete Exposed to Flexural Fatigue Loads:The Application of Ultrasonic Pulse Velocity,Impact-echo and Surface Electrical Resistance Method

In order to clarify the fatigue damage evolution of concrete exposed to flexural fatigue loads,ultrasonic pulse velocity(UPV),impact-echo technology and surface electrical resistance(SR) method were used.Damage variable based on the change of velocity of ultrasonic pulse(Du) and impact elastic wave(Di)were defined according to the classical damage theory.The influences of stress level,loading frequency and concrete strength on damage variable were measured.The experimental results show that Du and Di both present a three-stages trend for concrete exposed to fatigue loads.Since impact elastic wave is more sensitive to the microstructure damage in stage Ⅲ,the critical damage variable,i e,the damage variable before the final fracture of concrete of Di is slightly higher than that of Du.Meanwhile,the evolution of SR of concrete exposed to fatigue loads were analyzed and the relationship between SR and Du,SR and Di of concrete exposed to fatigue loads were established.It is found that the SR of concrete was decreased with the increasing fatigue cycles,indicating that surface electrical resistance method can also be applied to describe the damage of ballastless track concrete exposed to fatigue loads.

Grain boundary engineering for enhancing intergranular damage resistance of ferritic/martensitic steel P92

Ferritic/martensitic(F/M)steel is widely used as a structural material in thermal and nuclear power plants.However,it is susceptible to intergranular damage,which is a critical issue,under service conditions.In this study,to improve the resistance to intergranular damage of F/M steel,a thermomechanical process(TMP)was employed to achieve a grain boundary engineering(GBE)microstructure in F/M steel P92.The TMP,including cold-rolling thickness reduction of 6%,9%,and 12%,followed by austenitization at 1323 K for 40 min and tempering at 1053 K for 45 min,was applied to the as-received(AR)P92 steel.The prior austenite grain(PAG)size,prior austenite grain boundary character distribution(GBCD),and connectivity of prior austenite grain boundaries(PAGBs)were investigated.Compared to the AR specimen,the PAG size did not change significantly.The fraction of coincident site lattice boundaries(CSLBs,3≤Σ≤29)and Σ3^(n) boundaries along PAGBs decreased with increasing reduction ratio because the recrystallization fraction increased with increasing reduction ratio.The PAGB connectivity of the 6%deformed specimen slightly deteriorated compared with that of the AR specimen.Moreover,potentiodynamic polarization studies revealed that the intergranular damage resistance of the studied steel could be improved by increasing the fraction of CSLBs along the PAGBs,indicating that the TMP,which involves low deformation,could enhance the intergranular damage resistance.

Laser-induced damage on large-aperture fused silica gratings

Two sets of laser-damage experiments on large-aperture fused silica optics have been carried out in a high-power laser facility. Severe damage has been found on the grating which presented dense craters on the front surface. This phenomenon is quite different from other fused silica optics, which are damaged on the rear surface. The damage possibility due to the redeposition layer was ruled out by acid-etching the grating＇s front surface. The remarkable stimulated Brillouin scattering （SBS） effect was observed in grating and the reason for the front surface damage is thought to be the backward SBS.

Characteristics of Laser-Induced Surface and Bulk Damage of Large-Aperture Deuterated Potassium Dihydrogen Phosphate at 351 nm

Deuterated potassium dihydrogen phosphate damage performance at 351 nm is studied on a large-aperture laser system. Bulk and rear-surface damage are initiated under the 3ω fluences of 6.T J/cm2 and 33/cm2, and show different growth characteristics under multiple laser irradiations with the fluence of 6 J/cm2. The size and number of bulk damage keep unchanged once initiated. However, surface damage size also does not grow, while surface damage number increases linearly with laser shots. Different damage thresholds and growth behaviors suggest different formations of bulk and surface damage precursors. The cause of surface damage is supposed to be near-surface absorbing particles buried under the sol-gel coating.

Subsurface defect characterization and laser-induced damage performance of fused silica optics polished with colloidal silica and ceria

This paper mainly focuses on the influence of colloidal silica polishing on the damage performance of fused silica optics. In this paper, nanometer sized colloidal silica and micron sized ceria are used to polish fused silica optics. The colloidal silica polished samples and ceria polished samples exhibit that the root-mean-squared （RMS） average surface roughness values are 0.7 nm and 1.0 rim, respectively. The subsurface defects and damage performance of the polished optics are analyzed and discussed. It is revealed that colloidal silica polishing will introduce much fewer absorptive con- taminant elements and subsurface damages especially no trailing indentation fracture. The 355-nm laser damage test reveals that each of the fused silica samples polished with colloidal silica has a much higher damage threshold and lower damage density than ceria polished samples. Colloidal silica polishing is potential in manufacturing high power laser optics.

Laser-induced damage threshold in HfO_2/SiO_2 multilayer films irradiated by β-ray

Post-processing can effectively improve the resistance to laser damage in multilayer films used in a high power laser system. In this work, HfO_2/SiO_2 multilayer films are prepared by e-beam evaporation and then β-ray irradiation is employed as the post-processing method. The particle irradiation affects the laser induced damage threshold(LIDT),which includes defects, surface roughness, packing density and residual stress. The residual stress that is relaxed during irradiation changes from compressive stress into tensile stress. Our results indicate that appropriate tensile stress can improve LIDT remarkably. In view of the fact that LIDT rises from 8 J/cm^2 to 12 J/cm^2, i.e., 50% increase, after the film has been irradiated by 2.2×10^(13)/cm^2 β-ray, the particle irradiation can be used as a controllable and desirable postprocessing method to improve the resistance to laser induced damage.

Microstructure and 355 nm Laser-Induced Damage Characteristics of Al₂O₃Films Irradiated with Oxygen Plasma under Different Energy

Al2O3 films were prepared using electron beam evaporation at room temperature. The samples were irradiated with oxygen plasma under different energy. The variations in average surface defect density and root mean square (RMS) surface roughness were characterized using an optical microscope and an atomic force microscope. Surface average defect density increased after plasma treatment. The RMS surface roughness of the samples decreased from 1.92 nm to 1.26 nm because of surface atom restructuring after oxygen plasma conditioning. A 355 nm laser-induced damage experiment indicated that the as-grown sample with the lowest defect density exhibited a higher laser-induced damage threshold (1.12 J/cm2) than the other treated samples. Laser-induced damage images revealed that defect is one of the key factors that affect laser-induced damage on Al2O3 films.

Clinical characteristics, target organ damage and associate risk factors ofresistant hypertension determined by ambulatory blood pressure monitoringin patients aged ≥80 years

Objectives To investigate clinical characteristics, target organ damage, and the associated risk factors of the patients aged ≥ 80 yearswith true resistant hypertension （RH）. Methods Patients aged ≥ 80 years with hypertension （n = 1163） were included in this study. Theincluded participants attended a structured clinical examination and an evaluation of RH was carried out. The prevalence, clinical characteristicsand target organ damage of patients with RH were assessed. The associated clinical risk factors were analyzed by using logistic regression.Results The prevalence of RH diagnosis by 24-h ambulatory blood pressure monitoring assessment was 21.15%. End-diastolic left ven-tricular internal dimension, left ventricular mass index as well as prevalence of left ventricular hypertrophy were significantly greater in pa-tients with RH than in control group. The common carotid artery intimal media thickness, carotid walls thickness, common carotid arterydiameter and relative wall thickness were significant greater in RH group than in control. A relatively higher level of creatinine, estimatedglomerular filtration rate, microalbuminuria and retinal changes was found in RIt group than in control. A multivariate analysis showed thatpatients with a history of diabetes, higher body mass index （BMI） and lipid profiles were independent risk factors of RH. Conclusions Theprevalence of RH in patients aged ≥ 80 years was within the range of reported rates of the general population. Subjects with RH diagnosisshowed a higher occurrence of target organ damage than patients with well controlled blood pressure. Patients with diabetes, higher BMI andserum lipid profiles were independent risk factors for RH in patients aged ≥ 80 years.

Correlation of polishing-induced shallow subsurface damages with laser-induced gray haze damages in fused silica optics

Laser-induced damage in fused silica optics greatly restricts the performances of laser facilities. Gray haze damage,which is always initiated on ceria polished optics, is one of the most important damage morphologies in fused silica optics.In this paper, the laser-induced gray haze damages of four fused silica samples polished with CeO2, Al2O3, ZrO2, and colloidal silica slurries are investigated. Four samples all present gray haze damages with much different damage densities.Then, the polishing-induced contaminant and subsurface damages in four samples are analyzed. The results reveal that the gray haze damages could be initiated on the samples without Ce contaminant and are inclined to show a tight correlation with the shallow subsurface damages.

The effect of laser beam size on laser-induced damage performance

The influence of laser beam size on laser-induced damage performance, especially damage probability and the laser-induced damage threshold （LIDT）, is investigated. It is found that damage probability is dependent on beam size when various damage precursors with different potential behaviors are involved. This causes the damage probability and the LIDT to be different between cases under a large-apertnre beam and a small-aperture beam. Moreover, the fluenee fluctuation of the large-aperture laser beam brings out hot spots, which move randomly across the beam from shot to shot. Thus this leads the most probable maximum fluenee after many shots at any location on the optical component to be several times the average beam fluence, These two effects result in the difference in the damage performance of the optical component between the cases under a large-aperture and small-aperture laser.

Influence of Creep Strength of Weld on Interfacial Creep Damage of Dissimilar Welded Joint between Martensitic and Bainitic Heat-Resistant Steel

The mechanical properties, creep rupture strength, creep damage and failure characteristics of dissimilar metal welded joint （DMWJ） between martensitic （SA213T91） and bainitic heat-resistant steel （12Cr2MoWVTiB（G102）） have been investigated by means of pulsed argon arc welding, high temperature accelerated simulation, mechanical and creep rupture test, and scanning electronic microscope （SEM）. The results show that there is a marked drop of mechanical properties of undermatching joint, and low ductility cracking along weld/G102 interface is induced due to creep damage. Creep rupture strength of overmatching joint is the least. The mechanical properties of medium matching joint are superior to those of overmatching and undermatching joint, and creep damage and failure tendency along the interface of weld/G102 are lower than those of overmatching and undermatching joint after accelerated simulation for 500 h, 1 000 h, 1 500 h, and the creep rupture strength of medium matching joint is the same as that of undermatching joint. Therefore, it is reasonable that the medium matching material is used for dissimilar welded joint between martensitic and bainitic steel.

Laser-induced Damage of 355 nm High-reflective Mirror Caused by Nanoscale Defect

Al2O3/SiO2 multilayer high-reflective（HR） mirrors at 355 nm were prepared by electron beam evaporation, and post-irradiated with Ar/O mixture plasma. The surface defect density, reflective spectra, and laser-induced damage characteristics were measured using optical microscopy, spectrophotometry, a damage testing system, and scanning electron microscopy（SEM）, respectively. The results indicated that moderate-time of irradiation enhanced the laser-induced damage threshold（LIDT） of the mirror, but prolonged irradiation produced surface defects, resulting in LIDT degradation. LIDT of the mirrors initially increased and subsequently decreased with the plasma processing time. SEM damage morphologies of the mirrors revealed that nanoscale absorbing defects in sub-layers was one of the key factors limiting the improvement of LIDT in 355 nm HR mirror.

Damage Action of Alkali-resistant Glass Fiber in Cement-based Material

The compressive strength and flexural strength with the same strength class cement mortar of the alkali-resistant glass fiber cement mortar were tested in standard and hot-water curing condition, and the damage mechanism of alkali-resistant glass fiber was studied. The interaction mechanisms of the chemical erosion and physical injury in different curing conditions were studied in order to summarize the damage mechanism of alkali-resistant glass fiber in cement-based materials, and chloride diffusivity coefficient and porosity of cement mortar were tested in the different curing conditions. The experimental results are that the strength of cement based materials and fiber cement slurry interface zone were closely related, and heat curing could accelerate the hydration of cement, but inevitably enlarge the defect.

New Methodology for Evaluating Toughness of Composite Laminates-Investigation of Damage Resistance

The existing problems in toughened resin evaluation technology, particularly the disadvantage of the toughened resin identification method by CAI, is pointed out based on the point of view of composite structure design. It is proposed to evaluate the toughness of composites by both damage resistance and damage tolerance. Seven different toughness composites are investigated by impact and quasi\|static indentation tests. Based on experimental data analysis, the parameter that is most sensitive to the damage resistance is determined as the damage parameter. The parameter to evaluate the damage resistance and its measuring method are proposed.

Decoupling of DNA damage response signaling from DNA damages underlies temozolomide resistance in glioblastoma cells

Glioblastoma multiforme （GBM） is the most aggressive primary brain tumor in adults.Current therapy includes surgery,radiation and chemotherapy with temozolomide （TMZ）.Major determinants of clinical response to TMZ include methylation status of the O6-methylguanine-DNA methyltransferase （MGMT） promoter and mismatch repair （MMR） status.Though the MGMT promoter is methylated in 45% of cases,for the first nine months of follow-up,TMZ does not change survival outcome.Furthermore,MMR deficiency makes little contribution to clinical resistance,suggesting that there exist unrecognized mechanisms of resistance.We generated paired GBM cell lines whose resistance was attributed to neither MGMT nor MMR.We show that,responding to TMZ,these cells exhibit a decoupling of DNA damage response （DDR） from ongoing DNA damages.They display methylation-resistant synthesis in which ongoing DNA synthesis is not inhibited.They are also defective in the activation of the S and G2 phase checkpoint.DDR proteins ATM,Chk2,MDC1,NBS1 and gammaH2AX also fail to form discrete foci.These results demonstrate that failure of DDR may play an active role in chemoresistance to TMZ.DNA damages by TMZ are repaired by MMR proteins in a futile,reiterative process,which activates DDR signaling network that ultimately leads to the onset of cell death.GBM cells may survive genetic insults in the absence of DDR.We anticipate that our findings will lead to more studies that seek to further define the role of DDR in ultimately determining the fate of a tumor cell in response to TMZ and other DNA methylators.

Detecting Impact Damage in Carbon Fabric/epoxy-matrix Composites by Ultrasonic F-scan and Electrical Resistance Measurement

The status and the variation of electrical resistance of impacted carbon fiber/epoxy-matrix composites were studied by ultrasonic F-scan and electrical resistance measurement The experimental results shows that impact damage energy threshold value of carbon fabric/epoxy-matrix composites can determine by using ultrasonic F-scan. When the impact energy exceeds the threshold value, damage is generated in composites. Electrical resistance of impacted composites is changed owing to the contact of each carbon fiber unit in composites, which cause a change of the series-parallel in conductors. The veracity of detecting impact damage in composites can be improved in this case.

Graph theoretical analysis of limestone fracture network damage patterns based on uniaxial compression test

The topological attributes of fracture networks in limestone,subject to intense hydrodynamics and intricate geological discontinuities,substantially influence the mechanical and hydraulic characteristics of the rock mass.The dynamical evolution of fracture networks under stress is crucial for unveiling the interaction patterns among fractures.However,existing models are undirected graphs focused on stationary topology,which need optimization to depict fractures'dynamic development and rupture process.To compensate for the time and destruction terms,we propose the damage network model,which defines the physical interpretation of fractures through the ternary motif.We focus primarily on the evolution of node types,topological attributes,and motifs of the fracture network in limestone under uniaxial stress.Observations expose the varying behavior of the nodes'self-dynamics and neighbors'adjacent dynamics in the fracture network.This approach elucidates the impact of micro-crack behaviors on large brittle shear fractures from a topological perspective and further subdivides the progressive failure stage into four distinct phases(isolated crack growth phase,crack splay phase,damage coalescence phase,and mechanical failure phase)based on the significance profile of the motif.Regression analysis reveals a positive linear and negative power correlation between fracture network density and branch number to the rock damage resistance,respectively.The damage network model introduces a novel methodology for depicting the interaction of two-dimensional(2D)projected fractures,considering the dynamic spatiotemporal development characteristics and fracture geometric variation.It helps dynamically characterize properties such as connectivity,permeability,and damage factors while comprehensively assessing damage in rock mass fracture networks.

THE INVESTIGATION OF THE METAL DAMAGE AT THE CREEP BY THE METHOD OF ELECTRICAL RESISTANCE MEASURING

In this paper the method of damage measurement of metal structure at the creep is proposed.In contrast to other methods,it allows the measurement of this damage to be carried out in the process of creep test without unloading and cooling of specimens.Experimental damage curves during creep are obtained as a result of test data processing by the suggested method.The analysis of these curves leads to a conclusion that the material damage at repture is monotonically decreasing function of the applied stress.This conclusion is an experimental verification of the theoretical result,obtained earlier.

Evaluation of Impact Damage Tolerance in Carbon Fabric/epoxy-matrix Composites by Electrical Resistance Measurement

Impact damage tolerance is provided in intensity design on composites. The compression intensity of impacted composites requires more than 60% of its original intensity. The influence of impact on compressive intensity and electrical resistance of carbon fabric/epoxy-matrix composites was studied in this paper. The experimental results shows that impact can cause damage in composites, degenerate compressive intensity, and increase resistance. The electrical resistance change rate was used as an evaluation indicator of impact damage tolerance of composites. Impact damage, which results from the applying process of composites, can be identified in time by electrical resistance measurement. So, the safety performance of composites can also be improved.

Frost Resistance and Damage Velocity of Compressively Preloaded Concrete

The frost resistance and compressive strength degradation of concrete under the simultaneous action of compressive load and freeze-thaw cycles were experimentally investigated. Air-entrained and non-air-entrained specimens with different water/cement(w/c) ratios were subjected to different compressive stress by specially designed apparatus, while the specimens suffered freeze-thaw cycles. In order to track the strength degradation process, the nondestructive tests were carried out after each freeze-thaw cycle got the residual strength for each specimen. Based on the experimental data, a variable Kss was proposed to describe the damage velocity. Experimental results indicate that the deterioration processes are accelerated by the compressive loads, and the damage velocity increases with the increases of the preloading levels and w/c ratios. The air entrainment decreases the damage velocity and improves the frost resistance of non-air-entrained concrete, although it would reduce the compressive strength of concrete.