The center cutter of a hard rock tunnel boring machine(TBM) is installed on the cutterhead at a small radius and thus bears complex side force.Given this fact,the formation mechanism and change law of the side force s...The center cutter of a hard rock tunnel boring machine(TBM) is installed on the cutterhead at a small radius and thus bears complex side force.Given this fact,the formation mechanism and change law of the side force suffered by the center cutter were studied.Based on the rock shear failure criterion in combination with the lateral rolling width,a model for predicting the average side force was set up.Besides,a numerical analysis model of the rock fragmentation of the center cutter was established,and the instantaneous load changing features were investigated.Results shows that the inner side of the center cutter can form lateral rolling annulus in rock during the rotary cutting process.The smaller the installation radius is,the greater the cutter side force will be.In a working condition,the side force of the innermost center cutter is 11.66 k N,while it decreases sharply when installation radius increases.Variation tends to be gentle when installation radius is larger than 500 mm,and the side force of the outermost center cutter is reduced to 0.74 k N.展开更多
The surface profile behavior of workpieces sawn has been investigated. Six species were sawn under the condi-tion of four different kinds of cutting speed by the band saw. The real surface profile of a sawn workpiecc ...The surface profile behavior of workpieces sawn has been investigated. Six species were sawn under the condi-tion of four different kinds of cutting speed by the band saw. The real surface profile of a sawn workpiecc is composed of twosections, which arc the additivity of the waviness of filtered wave and roughness curve. The roughness of center line avernge aswell as amplitude decrease with the increasing of cutting speed for different kinds of species used in the experiment.展开更多
The nesting problem involves arranging pieces on a plate to maximize use of material. A new scheme for 2D ir- regular-shaped nesting problem is proposed. The new scheme is based on the NFP (No Fit Polygon) algorithm a...The nesting problem involves arranging pieces on a plate to maximize use of material. A new scheme for 2D ir- regular-shaped nesting problem is proposed. The new scheme is based on the NFP (No Fit Polygon) algorithm and a new placement principle for pieces. The novel placement principle is to place a piece to the position with lowest gravity center based on NFP. In addition, genetic algorithm (GA) is adopted to find an efficient nesting sequence. The proposed scheme can deal with pieces with arbitrary rotation and containing region with holes, and achieves competitive results in experiment on benchmark datasets.展开更多
基金Project (2013CB035401) supported by the National Basic Research Program of ChinaProject (51475478) supported by the National Natural Science Foundation of ChinaProject (2012AA041803) supported by the High-Tech Research and Development Program of China
文摘The center cutter of a hard rock tunnel boring machine(TBM) is installed on the cutterhead at a small radius and thus bears complex side force.Given this fact,the formation mechanism and change law of the side force suffered by the center cutter were studied.Based on the rock shear failure criterion in combination with the lateral rolling width,a model for predicting the average side force was set up.Besides,a numerical analysis model of the rock fragmentation of the center cutter was established,and the instantaneous load changing features were investigated.Results shows that the inner side of the center cutter can form lateral rolling annulus in rock during the rotary cutting process.The smaller the installation radius is,the greater the cutter side force will be.In a working condition,the side force of the innermost center cutter is 11.66 k N,while it decreases sharply when installation radius increases.Variation tends to be gentle when installation radius is larger than 500 mm,and the side force of the outermost center cutter is reduced to 0.74 k N.
文摘The surface profile behavior of workpieces sawn has been investigated. Six species were sawn under the condi-tion of four different kinds of cutting speed by the band saw. The real surface profile of a sawn workpiecc is composed of twosections, which arc the additivity of the waviness of filtered wave and roughness curve. The roughness of center line avernge aswell as amplitude decrease with the increasing of cutting speed for different kinds of species used in the experiment.
基金Project (No. 60573146) supported by the National Natural ScienceFoundation of China
文摘The nesting problem involves arranging pieces on a plate to maximize use of material. A new scheme for 2D ir- regular-shaped nesting problem is proposed. The new scheme is based on the NFP (No Fit Polygon) algorithm and a new placement principle for pieces. The novel placement principle is to place a piece to the position with lowest gravity center based on NFP. In addition, genetic algorithm (GA) is adopted to find an efficient nesting sequence. The proposed scheme can deal with pieces with arbitrary rotation and containing region with holes, and achieves competitive results in experiment on benchmark datasets.
