期刊文献+
共找到45,640篇文章
< 1 2 250 >
每页显示 20 50 100
Interphase migration and enrichment of lead and zinc during copper slag depletion
1
作者 Jun HAO Zhi-he DOU +2 位作者 Xing-yuan WAN Ting-an ZHANG Kun WANG 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2024年第9期3029-3041,共13页
An interphase migration and enrichment model of lead and zinc during molten copper slag depletion was established.The occurrence of various components in copper slag was predicted using sulfur-oxygen potential calcula... An interphase migration and enrichment model of lead and zinc during molten copper slag depletion was established.The occurrence of various components in copper slag was predicted using sulfur-oxygen potential calculations and confirmed through high-temperature experiments.The recovery rate of copper can reach 90.13%under the optimal conditions of 1200°C,an iron to silicon mass ratio of 1.0,3 wt.%ferrous sulfide,and a duration of 45 min.Lead(54.07 wt.%)and zinc(17.42 wt.%)are found in the flue dust as lead sulfate,lead sulfide,and zinc oxide,while copper matte contains lead(14.44 wt.%)and zinc sulfide(1.29 wt.%).The remaining lead and zinc are encapsulated as oxides within the fayalite phase. 展开更多
关键词 depletion lead copper slag STIRRING ZINC
下载PDF
A short overview of the lead iodide residue impact and regulation strategies in perovskite solar cells
2
作者 Eng Liang Lim Zhanhua Wei 《Journal of Energy Chemistry》 SCIE EI CAS CSCD 2024年第3期504-510,I0012,共8页
Lead iodide(PbI2) is a vital raw material for preparing perovskite solar cells(PSCs),and it not only takes part in forming the light absorption layer but also remains in the grain boundary as a passivator.In other wor... Lead iodide(PbI2) is a vital raw material for preparing perovskite solar cells(PSCs),and it not only takes part in forming the light absorption layer but also remains in the grain boundary as a passivator.In other words,the PbI2 content in the precursor and as formed film will affect the efficiency and stability of the PSCs.With moderate residual PbI2,it passivates the bulk/surface defects of perovskite,reduces the interfacial recombination,promotes the perovskite stability,minimizes the device hysteresis,and so on.Deficient PbI2 residue will reduce the interfacial passivation effect and device performance.In addition to facilitating the non-radiative recombination,over PbI2 residue can also lead to electronic insulation in the grain boundary and deteriorate the device performance.However,the impact and regulation of PbI2 residue on the device performance and stability is still not fully understood.Herein,a comprehensive and detailed review is presented by discussing the PbI2 residue impact and its regulation strategies(i.e., elimination,facilitation and conversion of the residue PbI2) to manipulate the PbI2 content,distribution and forms.Finally,we also show future outlooks in this field,with an aim to help further the progression of high-efficiency and stable PSCs. 展开更多
关键词 lead iodide RESIDUE REGULATION Perovskite solar cells Efficiency Stability
下载PDF
In-situ defect passivation assisted three-step printing of efficient and stable formamidine-lead bromide solar cells
3
作者 Hang Yang Tao Zhou +6 位作者 Haoyu Cai Wenjian Shen Hao Chen Yongjun Liu Juan Zhao Yi-Bing Cheng Jie Zhong 《Journal of Energy Chemistry》 SCIE EI CAS CSCD 2024年第9期396-405,共10页
Perovskite solar cells(PSCs)emerge as the most promising photovoltaics(PV)for their high performance and potential convenient cost-effective production routes comparing to the sophomore PV technologies.The printed PSC... Perovskite solar cells(PSCs)emerge as the most promising photovoltaics(PV)for their high performance and potential convenient cost-effective production routes comparing to the sophomore PV technologies.The printed PSCs with simplified device architecture and fabrication procedures could further enhance the competitive strength of PSC technology.In this work,we present an in-situ defect passivation(ISDP)assisted full-printing of high performance formamidine-lead bromide(FAPbBr_(3))PSCs.Only three rapid printing steps are involved for electron transporting layer(ETL),perovskite and carbon to form a complete solar cell on the low-cost fluorine-doped tin oxide(FTO)substrate.Long-chain polymer monomethyl ether polyethylene glycol is particularly utilized as the ISDP passivator,leading to conformal coating on the rough FTO and defect passivation for both ETL and perovskite during printing.A high efficiency of 10.85%(certified 10.14%)and a high V_(oc)up to 1.57 V are achieved for the printed device.The unencapsulated PSCs maintain above 90%of the initial efficiency after continuously heating at 85℃for 1000 h and over 80%of the efficiency after the maximum power point tracking for 3500 h.The fully printed semitransparent PSCs with carbon grids(CGs)show average visible light transmittance over 33%and an efficiency of 8.81%. 展开更多
关键词 Formamidinium lead bromide Fully printed Lowcosts Carbon electrode SEMITRANSPARENT
下载PDF
Cooperative composites anchored with single atom Pb and carbon confined PbO nanoparticles for superior lead-carbon batteries
4
作者 Puqiang He Yi Yang +4 位作者 Hui Huang Jing Huang Hongbiao Wang Yapeng He Zhongcheng Guo 《Journal of Energy Chemistry》 SCIE EI CAS CSCD 2024年第10期486-497,I0010,共13页
The mitigation of sulphation and parasitic hydrogen evolution is considered as prominent research emphasis for the development of lead-carbon batteries(LCBs)in large-scale energy storage applications.Here,cooperative ... The mitigation of sulphation and parasitic hydrogen evolution is considered as prominent research emphasis for the development of lead-carbon batteries(LCBs)in large-scale energy storage applications.Here,cooperative Pb-C composites consisting of single atom Pb and carbon-encapsulated PbO nanoparticles were prepared by freeze-drying technique and pyrolytic reduction to address above obstacles.The innovative use of Pb^(2+)to cross-link sodium alginate enabled a uniform distribution of Pb in the composites,generating Pb-C-PbO three-phase heterostructure.Experimental analysis and theoretical calculations revealed the synergistic interactions between single-atom Pb and PbO nanoparticles in suppressing parasitic hydrogen evolution and promoting the adsorption of Pb atoms.The presence of monatomic Pb and PbO enhanced the affinity of the composites for the negative active materials and facilitated the transformation of the active materials from bulk into spherical shapes to enhance the specific surface area,thereby counteracting sulphation.Through the coordinated integration of various functionalities offered by Pb@C-x,the cycle life of the battery at HRPSoC reaches 7025 cycles,which is two times for LCB with pure carbon materials.Additionally,the discharge capacity increased from 3.52 to 3.79 Ah.This study provides substantial insights into the construction of Pb-C composites for LCBs to inhibit negative sulphation and hydrogen evolution. 展开更多
关键词 lead-carbon battery Negative sulphation Hydrogen evolution SINGLE-ATOM lead carbon composites
下载PDF
MiR-107-3p/Atp6v0e1 contributes to protective effects of two selenium-containing peptides,TSeMMM and SeMDPGQQ on lead-induced neurotoxicity
5
作者 Yong Fang Tianhang Huang +5 位作者 Jian Wu Xieqi Luo Fengjiao Fan Peng Li Jian Ding Xinyang Sun 《Food Science and Human Wellness》 SCIE CAS CSCD 2024年第4期2060-2067,共8页
Two selenium(Se)-containing peptides from Se-enriched rice,TSeMMM and SeMDPGQQ,possess neuroprotective potency against lead(Pb2+)-induced cytotoxicity.However,the crosstalk between mRNA and microRNAs(miRNA)involved in... Two selenium(Se)-containing peptides from Se-enriched rice,TSeMMM and SeMDPGQQ,possess neuroprotective potency against lead(Pb2+)-induced cytotoxicity.However,the crosstalk between mRNA and microRNAs(miRNA)involved in the neuroprotection mechanism remains to be elucidated.In this study,RNA-sequencing and miRNA-sequencing were used to independently identify differentially expressed mRNAs and small RNAs profiles in Pb^(2+)-treated primary fetal rat cortical neurons and then the correlated miRNA-mRNA target pairs were obtained.It was found that 34 mRNAs related to oxidative phosphorylation could be reversed by pretreatment of TSeMMM and SeMDPGQQ.The protective effect of TSeMMM and SeMDPGQQ was mediated by upregulation of miR-107-3p,which downregulates the ATPase H+transporting V0 subunit e1(Atp6v0e1)mRNA level.A zebrafish model was applied to verify the relevance between the targeted mRNA and miRNA by real-time quantitative PCR.The results indicated that miR-107-3p was a potential therapeutic target to achieve neuroprotection of Se-containing peptides via stimulation of Atp6v0e1. 展开更多
关键词 lead Se-containing peptides NEUROPROTECTION miRNA
下载PDF
Epicatechin attenuates lead(Pb)-induced cognitive impairment in mice:regulation on Nrf2 signaling pathway,and interference on the interaction between Pb with albumin
6
作者 Dai Cheng Qianqian Yu +2 位作者 Kexin Zhu Dingdong Bu Zijian Wu 《Food Science and Human Wellness》 SCIE CSCD 2024年第2期1065-1078,共14页
Epicatechin(EC)was used in this study to antagonize the cognitive dysfunction caused by lead(Pb)exposure in mice.Eight-week-old male Kunming mice were treated with PbCl_(2)(20 mg/kg)and/or EC(50 mg/kg)by gavage admini... Epicatechin(EC)was used in this study to antagonize the cognitive dysfunction caused by lead(Pb)exposure in mice.Eight-week-old male Kunming mice were treated with PbCl_(2)(20 mg/kg)and/or EC(50 mg/kg)by gavage administration for 4 weeks.Morris water maze test showed that EC could improve memory dysfunction induced by Pb.EC antagonized Ca^(2+)overload,activated Nrf2 signaling pathway and reduced the accumulation of Pb in the brain and serum,which suggested that EC might alter Pb distribution in mice.In vitro,spectroscopic analysis,potentiometric titration and docking studies were applied to inquiry into the interaction between bovine serum albumin(BSA)and Pb^(2+)in presence or absence of EC.EC was proved to chelate Pb^(2+)and reduced the interaction between BSA and Pb^(2+).In summary,EC might protect Pb-induced cognitive impairment by activating Nrf2 signaling pathway,and suppressing Pb accumulation via interference on the binding of Pb to albumin. 展开更多
关键词 lead EPICATECHIN Bovine serum albumin Interaction Oxidative stress
下载PDF
Universal Encapsulation Adhesive for Lead Sedimentation and Attachable Perovskite Solar Cells with Enhanced Performance
7
作者 Xuehao Zhu Haoyu Cai +7 位作者 Cong Bai Zhengzhe Wu Wenjian Shen Yiming Xiong Juan Zhao Fuzhi Huang Yibing Cheng Jie Zhong 《Energy & Environmental Materials》 SCIE EI CAS CSCD 2024年第3期303-310,共8页
In this work,a modified polyurethane adhesive(PUA)was prepared to realize a convenient encapsulation strategy for lead sedimentation and attachable perovskite solar cells(A-PSCs).The modified PUA can completely self-h... In this work,a modified polyurethane adhesive(PUA)was prepared to realize a convenient encapsulation strategy for lead sedimentation and attachable perovskite solar cells(A-PSCs).The modified PUA can completely self-heal within 45 min at room temperature with an efficient lead ion-blocking rate of 99.3%.The PUA film can be coated on a metal electrode with slight efficiency improvement from 23.96%to 24.15%.The thermal stability at 65℃and the humidity stability at 55%relative humidity(RH)are superior to the devices encapsulated with polyisobutylene.The PUA film has strong adhesion to the flexible substrate and the initial efficiency of the flexible perovskite module(17.2%)encapsulated by PUA remains 92.6%within 1825 h.These results suggest that PUA encapsulation is universal for rigid and flexible PSCs with enhanced stability and low lead hazards.Moreover,it was found that flexible PSCs can be well attached to various substrates with PUA,providing a facile route for the A-PSCs in various scenarios without additional encapsulation and installation. 展开更多
关键词 ADHESIVE attachable device flexible module lead leakage POLYURETHANE
下载PDF
Seasonal Characteristics of Forecasting Uncertainties in Surface PM_(2.5)Concentration Associated with Forecast Lead Time over the Beijing-Tianjin-Hebei Region
8
作者 Qiuyan DU Chun ZHAO +6 位作者 Jiawang FENG Zining YANG Jiamin XU Jun GU Mingshuai ZHANG Mingyue XU Shengfu LIN 《Advances in Atmospheric Sciences》 SCIE CAS CSCD 2024年第5期801-816,共16页
Forecasting uncertainties among meteorological fields have long been recognized as the main limitation on the accuracy and predictability of air quality forecasts.However,the particular impact of meteorological foreca... Forecasting uncertainties among meteorological fields have long been recognized as the main limitation on the accuracy and predictability of air quality forecasts.However,the particular impact of meteorological forecasting uncertainties on air quality forecasts specific to different seasons is still not well known.In this study,a series of forecasts with different forecast lead times for January,April,July,and October of 2018 are conducted over the Beijing-Tianjin-Hebei(BTH)region and the impacts of meteorological forecasting uncertainties on surface PM_(2.5)concentration forecasts with each lead time are investigated.With increased lead time,the forecasted PM_(2.5)concentrations significantly change and demonstrate obvious seasonal variations.In general,the forecasting uncertainties in monthly mean surface PM_(2.5)concentrations in the BTH region due to lead time are the largest(80%)in spring,followed by autumn(~50%),summer(~40%),and winter(20%).In winter,the forecasting uncertainties in total surface PM_(2.5)mass due to lead time are mainly due to the uncertainties in PBL heights and hence the PBL mixing of anthropogenic primary particles.In spring,the forecasting uncertainties are mainly from the impacts of lead time on lower-tropospheric northwesterly winds,thereby further enhancing the condensation production of anthropogenic secondary particles by the long-range transport of natural dust.In summer,the forecasting uncertainties result mainly from the decrease in dry and wet deposition rates,which are associated with the reduction of near-surface wind speed and precipitation rate.In autumn,the forecasting uncertainties arise mainly from the change in the transport of remote natural dust and anthropogenic particles,which is associated with changes in the large-scale circulation. 展开更多
关键词 PM_(2.5) forecasting uncertainties forecast lead time meteorological fields Beijing-Tianjin-Hebei region
下载PDF
Seismic evaluation of frequency influence and resonant behavior for lead rubber bearing isolated rigid rectangular liquid tanks
9
作者 Jyoti Ranjan Barik Kishore Chandra Biswal 《Earthquake Engineering and Engineering Vibration》 SCIE EI CSCD 2024年第4期973-994,共22页
The seismic behavior of a partially filled rigid rectangular liquid tank is investigated under short-and longduration ground motions.A finite element model is developed to analyze the liquid domain by using four-noded... The seismic behavior of a partially filled rigid rectangular liquid tank is investigated under short-and longduration ground motions.A finite element model is developed to analyze the liquid domain by using four-noded quadrilateral elements.The competency of the model is verified with the available results.Parametric studies are conducted for the dynamic parameters of the base-isolated tank,using a lead rubber bearing to evaluate the optimum damping and time period of the isolator.The application of base isolation has reduced the total and impulsive hydrodynamic components of pressure by 80 to 90 percent,and base shear by 15 to 95 percent,depending upon the frequency content and duration of the considered earthquakes.The sloshing amplitude of the base-isolated tank is reduced by 18 to 94 percent for most of the short-duration earthquakes,while it is increased by 17 to 60 percent for the majority of the long-duration earthquakes.Furthermore,resonance studies are carried out through a long-duration harmonic excitation to obtain the dynamic behavior of non-isolated and isolated tanks,using a nonlinear sloshing model.The seismic responses of the base-isolated tank are obtained as higher when the excitation frequency matches the fundamental sloshing frequency rather than the isolator frequency. 展开更多
关键词 lead rubber bearing frequency domain resonant inputs long-duration excitation
下载PDF
Hot carrier cooling in lead halide perovskites probed by two-pulse photovoltage correlation spectroscopy
10
作者 Yuqing Huang Chaoyu Guo +9 位作者 Lei Gao Wenna Du Haotian Zheng Da Wu Zhengpu Zhao Chu-Wei Zhang Qin Wang Xin-Feng Liu Qingfeng Yan Ying Jiang 《Chinese Physics B》 SCIE EI CAS CSCD 2024年第10期116-119,共4页
The next-generation hot-carrier solar cells,which can overcome the Shockley-Queisser limit by harvesting excessenergy from hot carriers,are receiving increasing attention.Lead halide perovskite(LHP)materials are consi... The next-generation hot-carrier solar cells,which can overcome the Shockley-Queisser limit by harvesting excessenergy from hot carriers,are receiving increasing attention.Lead halide perovskite(LHP)materials are considered aspromising candidates due to their exceptional photovoltaic properties,good stability and low cost.The cooling rate of hotcarriers is a key parameter influencing the performance of hot-carrier solar cells.In this work,we successfully detected hotcarrier dynamics in operando LHP devices using the two-pulse photovoltage correlation technique.To enhance the signalto-noise ratio,we applied the delay-time modulation method instead of the traditional power modulation.This advancementallowed us to detect the intraband hot carrier cooling time for the organic LHP CH_(3)NH_(3)PbBr_(3),which is as short as 0.21 ps.In comparison,the inorganic Cs-based LHP CsPbBr_(3)exhibited a longer cooling time of around 0.59 ps due to differentphonon contributions.These results provide us new insights into the optimal design of hot-carrier solar cells and highlightthe potential of LHP materials in advancing solar cell technology. 展开更多
关键词 two-pulse correlation spectroscopy lead halide perovskites hot carrier cooling ultrafast dynamics
下载PDF
CFD modeling of gas−liquid flow phenomenon in lead smelting oxygen-enriched side-blown furnace
11
作者 Zhen-yu ZHU Ping ZHOU +3 位作者 Xing-bang WAN Zhuo CHEN Ling ZHANG Shi-bo KUANG 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2024年第8期2671-2685,共15页
A validated numerical model was established to simulate gas−liquid flow behaviors in the oxygen-enriched side-blown bath furnace.This model included the slip velocity between phases and the gas thermal expansion effec... A validated numerical model was established to simulate gas−liquid flow behaviors in the oxygen-enriched side-blown bath furnace.This model included the slip velocity between phases and the gas thermal expansion effect.Its modeling results were verified with theoretical correlations and experiments,and the nozzle-eroded states in practice were also involved in the analysis.Through comparison,it is confirmed that the thermal expansion effect influences the flow pattern significantly,which may lead to the backward motion of airflow and create a potential risk to production safety.Consequently,the influences of air injection velocity and furnace width on airflow behavior were investigated to provide operating and design guidance.It is found that the thin layer melt,which avoids high-rate oxygen airflow eroding nozzles,shrinks as the injection velocity increases,but safety can be guaranteed when the velocity ranges from 175 to 275 m/s.Moreover,the isoline patterns and heights of thin layers change slightly when the furnace width increases from 2.2 to 2.8 m,indicating that the furnace width shows a limited influence on production safety. 展开更多
关键词 multiphase flow horizontal gas injection backward motion of airflow gas thermal expansion side-blown furnace lead smelting
下载PDF
Research on Leading Edge Erosion and Aerodynamic Characteristics of Wind Turbine Blade Airfoil
12
作者 Xin Guan Yuqi Xie +2 位作者 Shuaijie Wang Mingyang Li Shiwei Wu 《Fluid Dynamics & Materials Processing》 EI 2024年第9期2045-2058,共14页
The effects of the erosion present on the leading edge of a wind turbine airfoil(DU 96-W-180)on its aerodynamic performances have been investigated numerically in the framework of a SST k–ωturbulence model based on ... The effects of the erosion present on the leading edge of a wind turbine airfoil(DU 96-W-180)on its aerodynamic performances have been investigated numerically in the framework of a SST k–ωturbulence model based on the Reynolds Averaged Navier-Stokes equations(RANS).The results indicate that when sand-induced holes and small pits are involved as leading edge wear features,they have a minimal influence on the lift and drag coefficients of the airfoil.However,if delamination occurs in the same airfoil region,it significantly impacts the lift and resistance characteristics of the airfoil.Specifically,as the angle of attack grows,there is a significant decrease in the lift coefficient accompanied by a sharp increase in the drag coefficient.As wear intensifies,these effects gradually increase.Moreover,the leading edge wear can exacerbate flow separation near the trailing edge suction surface of the airfoil and cause forward displacement of the separation point. 展开更多
关键词 Wind energy wind turbine EROSION AIRFOIL leading edge erosion characteristics aerodynamic performance numerical simulation
下载PDF
Leading Pattern of Spring Drought Variability over East Asia and Associated Drivers
13
作者 赵庆红 杨崧 +1 位作者 田红瑛 邓开强 《Journal of Tropical Meteorology》 SCIE 2024年第1期1-10,共10页
Drought events have become more frequent and intense over East Asia in recent decades,leading to huge socioeconomic impacts.Although the droughts have been studied extensively by cases or for individual regions,their ... Drought events have become more frequent and intense over East Asia in recent decades,leading to huge socioeconomic impacts.Although the droughts have been studied extensively by cases or for individual regions,their leading variability and associated causes remain unclear.Based on the Standardized Precipitation Evapotranspiration Index(SPEI)and ERA5 reanalysis product from 1979 to 2020,this study evealuates the severity of spring droughts in East Asia and investigates their variations and associated drivers.The results indicate that North China and Mongolia have experienced remarkable trends toward dryness during spring in recent decades,while southwestern China has witnessed an opposite trend toward wetness.The first Empirical Orthogonal Function mode of SPEI variability reveals a similar seesawing pattern,with more severe dryness in northwestern China,Mongolia,North China,South Korea,and Japan but increased wetness in Southwestern China and southeast Asia.Further investigation reveals that the anomalously dry(wet)surface in North(Southwestern)China is significantly associated with anomalously high(low)temperature,less(more)precipitation,and reduced(increased)soil moisture during the previous winter and early spring,regulated by an anomalous anticyclone(cyclone)and thus reduced(increased)water vapor convergence.The spring dry-wet pattern in East Asia is also linked to cold sea surface temperature anomalies in the central-eastern Pacific.The findings of this study have important implications for improving the prediction of spring drought events in East Asia. 展开更多
关键词 DROUGHT leading pattern East Asia spring DRIVERS
下载PDF
Management of a patient with an unusual trajectory of a temporary trans-venous pacing lead
14
作者 Metesh Acharya Ethan Kavanagh +2 位作者 Sheena Garg Davorin Sef Fabio De Robertis 《World Journal of Cardiology》 2024年第6期314-317,共4页
Perforation of the right ventricle during placement of pacing wires is a welldocumented complication and can be potentially fatal.Use of temporary pacemaker,helical screw leads and steroids use prior to implant are re... Perforation of the right ventricle during placement of pacing wires is a welldocumented complication and can be potentially fatal.Use of temporary pacemaker,helical screw leads and steroids use prior to implant are recognised as risk factors for development of post-permanent pacemaker effusion.We reported an unusual case of pacing wire perforating interventricular septum into the left ventricle that occurred during the implant procedure performed in another institution.After the preoperative work-up and transfer to our tertiary cardiothoracic centre,the patient underwent successful surgical management.In conclusion,early recognition and timely diagnosis using advanced multimodality imaging can guide surgical intervention and prevent unfavourable consequences of device-related complications. 展开更多
关键词 Ventricular perforation lead perforation PACING
下载PDF
Conformity Assessment of Lead Aprons Used in Conventional Radiology: A Multi-Centre Survey in Togo
15
作者 Massaga Dagbé Bidamin N’timon +8 位作者 Ousmane Aminata Bah Pihou Gbandé Komi Awobanou Koku Adambounou Masamaesso Tchaou Abdoulatif Amadou Lantam Sonhaye Lama Kegdigoma Agoda-koussema Komlanvi Victor Adjénou 《Open Journal of Radiology》 2024年第2期55-63,共9页
Aim: Lead aprons are used to protect against scattered radiation from the patient during interventional procedures and certain special conventional radiological examinations. Given the importance of the role lead apro... Aim: Lead aprons are used to protect against scattered radiation from the patient during interventional procedures and certain special conventional radiological examinations. Given the importance of the role lead aprons are supposed to play in radiation protection, we propose to assess their conformity in medical imaging departments in public and religious hospitals in Togo. Materials and method: A multi-centre survey conducted from 26 November to 06 December 2021 in the radiology departments of public and religious health facilities in Togo. All aprons in use were included. The evaluation criteria were physical (visual), quantitative (radiographic) and qualitative (dosimetric). Results: We had registred 43 aprons among wich 27 (62.79%) leaded aprons were labelled non-compliant and 16 (37.21%) were labelled compliant. Of the aprons judged to be non-compliant, 70.37% were more than 10 years old and 96.30% showed defects on the radiographic images. The most common defects were vampire marks (18.64%), multiple folds (16.96%), cracks (16.96%), multiple cracks (15.25%), tears (8.47%), absence of lead (5.08%), holes (3.39%) and lead corrosion (1.69%). Defective aprons (62.96%) had at least two defects. The defects were of thoraco-abdomino-pelvic (74.07%), thoracic (14.82%) and abdomino-pelvic (11.11%) topography. For indirect exposure at 50 and 70 kilovolts, all the aprons had an attenuation factor greater than 90%. After dosimetric measurement, 13.95% of aprons had attenuation factors below 90% for indirect exposure at 100 kilovolts. Conclusion: The compliance of the leaded decks is trifactorial (physical, radiographic and dosimetric). However, there is no significant difference in X-ray attenuation capacity between defective and normal decks. 展开更多
关键词 lead Apron Compliance Radiation Protection RADIOLOGY TOGO
下载PDF
Exploring the Path of Party Building Leading League Construction in Colleges and Universities under the Pattern of Great Ideological and Political Education
16
作者 Yi SHENG Tao LI 《Asian Agricultural Research》 2024年第5期42-46,共5页
In accordance with the pattern of"great ideology and politics",the Party and youth League organizations assume the role of vanguard in the organization of colleges and universities.Simultaneously,they serve ... In accordance with the pattern of"great ideology and politics",the Party and youth League organizations assume the role of vanguard in the organization of colleges and universities.Simultaneously,they serve as a pivotal force in ideological and political education.In order to construct a comprehensive ideological and political framework encompassing the entire educational process,it is of paramount importance to identify an efficacious methodology for Party building leading League construction.This paper employs a comprehensive analysis to elucidate the pivotal role of Party building leading League construction in facilitating ideological and political education.It also illuminates the practical challenges encountered in the implementation of Party building leading League construction initiatives within colleges and universities.The article proposes a specific path for Party building leading League construction in colleges and universities based on three key aspects:cohesion of the consensus of Party building leading League building,establishment of the institutional system of Party building leading League construction,and creation of the model brand of Party building leading League construction.The aim is to promote in-depth development of Party building in colleges and universities and enhance the quality and effect of ideological and political education. 展开更多
关键词 Great ideological and political education pattern Party building in universities and colleges Party building leading League construction
下载PDF
Analysis of Oxygen Consumption in Lead and Zinc Metallurgy
17
作者 Lun Sheng Pengpeng Zhang 《Frontiers of Metallurgical Industry》 2024年第2期5-9,共5页
This article analyzes the role of oxygen in lead zinc metallurgy,including shortening the metallurgical process,promoting energy conservation and environmental protection,improving metallurgical strength,enhancing raw... This article analyzes the role of oxygen in lead zinc metallurgy,including shortening the metallurgical process,promoting energy conservation and environmental protection,improving metallurgical strength,enhancing raw material adaptability,and enhancing comprehensive recovery efficiency.This article introduces different lead zinc metallurgical processes and their oxygen consumption characteristics,including oxygen enriched side blowing lead smelting,oxygen bottom blowing lead smelting,oxygen enriched top blowing lead smelting,flash smelting lead,oxygen pressure leaching zinc smelting,and atmospheric pressure oxygen leaching zinc smelting.It is pointed out that oxygen enhanced metallurgy is the direction for the transformation and upgrading of lead zinc metallurgy. 展开更多
关键词 lead zinc metallurgy oxygen rich smelting oxygen pressure leaching energy conservation and emission reduction
下载PDF
MER联合Lead-DBS在帕金森病患者术后程控中的应用研究
18
作者 刘明辉 杨新超 +2 位作者 路小奇 田海港 郭效东 《临床研究》 2024年第7期11-14,共4页
目的探讨微电极记录(MER)联合多模态影像融合技术(Lead-DBS)多模态影像融合技术在帕金森病患者术后程控中的应用效果。方法选取中国人民解放军联勤保障部队第九八八医院2018年10月至2023年8月期间收治的60例帕金森病患者,随机将其分为... 目的探讨微电极记录(MER)联合多模态影像融合技术(Lead-DBS)多模态影像融合技术在帕金森病患者术后程控中的应用效果。方法选取中国人民解放军联勤保障部队第九八八医院2018年10月至2023年8月期间收治的60例帕金森病患者,随机将其分为对照组和观察组。对照组患者根据脑深部电刺激术(DBS)专家程控共识逐个触点程控,观察组患者根据MER联合术后Lead-DBS多模态影像融合技术进行程控。比较两组术中操作时间、术后症状改善情况、生活质量评分、不良情绪及并发症发生率。结果观察组术中操作时间少于对照组,差异具有统计学意义(P<0.05);干预前两组帕金森症状评分、帕金森病生活质量评分、不良情绪评分、并发症发生率差异均无统计学意义(P>0.05),干预后观察组帕金森症状评分、帕金森病生活质量评分、不良情绪评分、并发症发生率均低于对照组,差异均有统计学意义(P<0.05)。结论术中MER联合术后Lead-DBS多模态影像融合技术,结合患者症状针对性选择开机触点方法具有较高的可行性,可提高手术效率、改善患者预后,安全性良好。 展开更多
关键词 MER lead-DBS 帕金森病 术后程控
下载PDF
Mechanical and Electrical Properties of Some Sn-Zn Based Lead-Free Quinary Alloys
19
作者 Shihab Uddin Md. Abdul Gafur +1 位作者 Suraya Sabrin Soshi Mohammad Obaidur Rahman 《Materials Sciences and Applications》 2024年第7期213-227,共15页
Although there are many lead-free soldering alloys on the market, none of them have ideal qualities. The researchers are combining binary alloys with a variety of additional materials to create the soldering alloys’ ... Although there are many lead-free soldering alloys on the market, none of them have ideal qualities. The researchers are combining binary alloys with a variety of additional materials to create the soldering alloys’ features. The eutectic Sn-9Zn alloy is among them. This paper investigated the mechanical and electrical properties of Sn-9Zn-x (Ag, Cu, Sb);{x = 0.2, 0.4, and 0.6} lead-free solder alloys. The mechanical properties such as elastic modulus, ultimate tensile strength (UTS), yield strength (YS), and ductility were examined at the strain rates in a range from 4.17 10−3 s−1 to 208.5 10−3 s−1 at room temperature. It is found that increasing the content of the alloying elements and strain rate increases the elastic modulus, ultimate tensile strength, and yield strength while the ductility decreases. The electrical conductivity of the alloys is found to be a little smaller than that of the Sn-9Zn eutectic alloy. 展开更多
关键词 lead-Free Solder Strain Rate Ultimate Tensile Strength DUCTILITY Electrical Conductivity
下载PDF
MER联合Lead-DBS在帕金森病患者术后程控中的应用 被引量:1
20
作者 梁立志 孙玉玺 +4 位作者 周金山 程哲 代凤 束汉生 王大巍 《中国实用神经疾病杂志》 2023年第5期548-554,共7页
目的探索帕金森病患者术中微电极记录(MER)联合术后Lead-DBS多模态影像融合技术,结合患者症状针对性选择开机触点方法的可行性。方法依照脑深部电刺激术(DBS)术后程控方式的差异,分析80例接受DBS治疗的帕金森病(PD)患者病例资料,随机分... 目的探索帕金森病患者术中微电极记录(MER)联合术后Lead-DBS多模态影像融合技术,结合患者症状针对性选择开机触点方法的可行性。方法依照脑深部电刺激术(DBS)术后程控方式的差异,分析80例接受DBS治疗的帕金森病(PD)患者病例资料,随机分为2组。实验组患者术中MER联合术后Lead-DBS多模态影像融合技术,结合患者症状针对性选择开机触点进行程控;对照组患者根据DBS专家程控共识逐个触点程控。结果首次开机时间:对照组(136.30±11.81)min,实验组(86.05±7.05)min,2组比较差异有统计学意义(P<0.05),实验组开机时间明显缩短;首次程控不良反应次数:实验组(0.90±0.50)次,对照组(3.03±1.00)次,2组比较差异有统计学意义(P<0.05),实验组不良反应次数显著减少;药物“关”期情况下,术后开机与关机帕金森病评定量表第三部分(UPDRS-Ⅲ)评分改善率:实验组术后开机UPDRS-Ⅲ平均改善率为47.60%,对照组平均改善率为46.60%,差异无统计学意义(P>0.05),但实验组临床运动功能的改善程度优于对照组;帕金森病生活质量评分(PDQ-39)改善率:实验组术后开机平均改善率为47.60%,对照组平均改善率为46.60%,差异无统计学意义(P>0.05),实验组生活质量改善程度高于对照组;6个月内门诊程控次数:实验组(2.20±0.85)次,对照组(4.08±1.89)次,差异无统计学意义(P>0.05),实验组半年内门诊程控次数较对照组减少。结论患者术中MER联合术后Lead-DBS多模态影像融合技术,结合患者症状针对性选择开机触点的方法,具有安全,高效,开机不良反应少的优点,更倾向个体化治疗,可作为DBS术后程控新的尝试方案。 展开更多
关键词 微电极记录 脑深部电极植入术 lead-DBS 帕金森病 程控
下载PDF
上一页 1 2 250 下一页 到第
使用帮助 返回顶部