Studies on the Behaviors of PbSO_4/Pb and PbO_2/PbSO_4 Electrodes Prepared from Lead Carbonate by Powder Microelectrode Technique

The behaviors ot PbSO4/Pb and PbO4/PbSO4 electrode prepared from PbCO3 have been examined using powder microelectrode(PME) technique and cyclic voltammetry(CV). Firstly, PMEs parked with Pb- CO3 transformed into PtSO4 PME in 1. 0 mol/L H2SO4 solution at 30 C, and then the PbSO4 in the PMEs were formed to Pb or PbO2 using an unsymmetrical signal(Qa/Qe for PbSO4/Pb electrode and Qe/Qa for PsO2/ PbSO4 electrode being 0. 1-0. 3) in 2. S mol/L H2SO4 solution. The results show that the CV characteristic of either PbSO4/Pb or PsO2/PbSO4 PME prepared from PhCO3 are as good as that of both electrodes made from lead oxide powder produced by ball mill.

Sulfidation roasting of lead and zinc carbonate with sulphur by temperature gradient method

In order to enhance the lead and zinc recovery from the refractory Pb-Zn oxide ore, a new technology was developed based on sulfidation roasting with sulphur by temperature gradient method. The solid-liquid reaction system was established and the sulfidation thermodynamics of lead and zinc carbonate was calculated with the software HSC 5.0. The effects of roasting temperature,molar ratio of sulphur to lead and zinc carbonate and reaction time in the first step roasting, and holding temperature and time in the second roasting on the sulfidation extent were studied at a laboratory-scale. The experimental results show that the sulfidation extents of lead and zinc are 96.50% and 97.29% under the optimal conditions, respectively, and the artificial galena, sphalerite and wurtzite were formed. By the novel sulfidizing process, it is expected that the sulphides can be recovered by conventional flotation technology.

Highly reversible lead-carbon battery anode with lead grafting on thecarbon surface

A novel C/Pb composite has been successfully prepared by electmless plating to reduce the hydrogenevolution and achieve the high reversibility of the anode of lead-carbon battery （LCB）. The depositedlead on the surface of C/Pb composite was found to be uniform and adherent to carbon surface. Becauselead has been stuck on the surface of C/Pb composite, the embedded structure suppresses the hydrogenevolution of lead-carbon anode and strengthens the connection between carbon additive and sponge lead.Compared with the blank anode, the lead-carbon anode with C/Pb composite displays excellent charge-discharge reversibility, which is attributed to the good connection between carbon additives and leadthat has been stuck on the surface of C/Pb composite during the preparation process. The addition of CIPb composite maintains a solid anode structure with high specific surface area and power volume, andthereby, it plays a significant role in the highly reversible lead-carbon anode.

Spallation Yield of Neutrons Produced in Thick Lead Target by 400 MeV/u Carbon Ions

Measurement of the neutron yield is performed at a primary energy of 400 MeV/u carbons for the Pb target.Water-bath activation-foil method is used in a moderation measurement with Au foils to detect the moderated neutrons. The neutron yield is determined to be 18.4±2.1 per carbon by integrating the neutron flux over the entire water volume. The corresponding simulation values are performed by Geant4 code with three models to compare with the experimental results. The comparison shows that the calculated result with the INCL model is in good agreement with the experimental data.

Zero-valent iron doped carbons readily developed from sewage sludge for lead removal from aqueous solution

Low-cost but high-efficiency composites of iron-containing porous carbons were prepared using sewage sludge and ferric salts as raw materials. Unlike previous time- and energy-consuming manufacturing procedures, this study shows that pyrolyzing a mixture of sludge and ferric salt can produce suitable composites for lead adsorption. The specific surface area, the total pore volume and the average pore width of the optimal composite were 321 m^2/g, 0.25 cm^3/g, and 3.17 nm, respectively. X-ray diffraction analysis indicated that ferric salt favored the formation of metallic iron, while Fourier transform infrared spectroscopy revealed the formation of hydroxyl and carboxylic groups. The result of batch tests indicated that the adsorption capacity of carbons activated with ferric salt could be as high as 128.9 mg/g, while that of carbons without activation was 79.1 mg/g. The new manufacturing procedure used in this study could save at least 19.5 k J of energy per gram of activated carbon.

A study of differential potentiometric stripping analysis for lead and cadmium with Nafion coated carbon fibre electrode

The differential potentiometric stripping analysis (DPSA) with Nafion coated carbon fibre electrode has been studied, and a method to determine lead and cadmium in urine directly has been attempted. The effect of various experimental parameters on the DPSA response is discussed. The experimental conditions include 0.2M sodium perchlorate, deposition potential of-1.0 or -1.1 V and using 20 ppm mercuric ion as oxidizing agent. The response of the signal is in linear relation with the concentrations of lead and cadmium respectively up to 0.5 ppm. The electrode coated with Nafion film alleviates the interference from organics in urine samples.