Underwater four-quadrant dual-beam circumferential scanning laser fuze using nonlinear adaptive backscatter filter based on pauseable SAF-LMS algorithm

The phenomenon of a target echo peak overlapping with the backscattered echo peak significantly undermines the detection range and precision of underwater laser fuzes.To overcome this issue,we propose a four-quadrant dual-beam circumferential scanning laser fuze to distinguish various interference signals and provide more real-time data for the backscatter filtering algorithm.This enhances the algorithm loading capability of the fuze.In order to address the problem of insufficient filtering capacity in existing linear backscatter filtering algorithms,we develop a nonlinear backscattering adaptive filter based on the spline adaptive filter least mean square(SAF-LMS)algorithm.We also designed an algorithm pause module to retain the original trend of the target echo peak,improving the time discrimination accuracy and anti-interference capability of the fuze.Finally,experiments are conducted with varying signal-to-noise ratios of the original underwater target echo signals.The experimental results show that the average signal-to-noise ratio before and after filtering can be improved by more than31 d B,with an increase of up to 76%in extreme detection distance.

基于CEEMDAN-VSSLMS的滚动轴承故障诊断

针对传统机械轴承故障诊断模型易受系统噪声干扰、特征识别效率低等问题,提出一种基于信号固有模式深度建模分析的轴承故障诊断方法。首先,将采集到的轴承振动信号进行噪声自适应完全经验模态分解(CEEMDAN),获得不同时间尺度的局部特征信号,使用相关系数判别并去除虚假模态分量,再利用可变步长最小均方算法(VSSLMS)对剩余IMF分量降噪并进行重构;然后,将降噪后的振动信号进行离散小波变换(DWT)得到时频谱图,并利用形态学开运算进行特征增强;最后利用改进GoogLeNet网络模型对特征图进行训练,通过Softmax分类器完成特征归类,从而实现轴承故障诊断。将提出的故障诊断方法应用于不同工况下的轴承故障数据集,试验结果表明,所提方法在噪声干扰下具有较高的诊断精度。

基于镜像修正FxLMS控制算法的船舶管路振动主动控制

针对船舶管路减振和抗冲击的需求,本文根据镜像修正自适应滤波算法,设计出了一种管路振动主动控制策略,能够有效地控制管路在低频下的振动,并且在次级通道发生突变时,控制系统可再次快速收敛,进行稳定控制。本文先对镜像修正自适应滤波算法进行理论研究,分析算法的迭代及控制过程;再通过仿真分别验证算法在不同参考信号输入下的收敛性及稳定性;最后搭建实验台架,通过试验验证算法的实际控制效果。试验结果表明:该控制策略在管路振动主动控制中能够降低15.37%的振动强度,比自适应滤波算法控制策略的控制效果好8.85%。所以镜像修正自适应滤波算法能够及时有效地进行管路振动控制。

一种基于动态门限与LMS算法相结合的多径干扰抑制算法

在船舰行驶过程中,信号的传输在岛屿反射与海面散射影响下易产生多径效应,使船舰的无线地空数据接收系统受到影响。为提高接收机的接收性能,首先完成了多径信道的建模,搭建了三径信道模型,并在此模型下,将动态门限法与最小均方(LMS)算法进行改进结合,并用此算法完成了信号处理的研究与仿真。仿真结果表明,所提算法优化方案可以提高在此种情况下信号接收系统的准确性。

基于sigmoid-sinh分段函数的变步长FxLMS算法

为改善滤波-x最小均方(filtered-x least mean square,FxLMS)算法在噪声主动控制时无法兼顾收敛速度和稳态误差的问题,提出了基于sigmoid-sinh分段函数的FxLMS(SSFxLMS)算法,并引入蚁狮算法对SFxLMS(sigmoid filtered-x least mean square)、ShFxLMS(sinh filtered-x least mean square)、SSFxLMS算法的参数进行优化。分别采用高斯白噪声和实测簇绒地毯织机噪声为输入信号,采用FxLMS、SFxLMS、ShFxLMS、SSFxLMS算法进行噪声主动控制仿真,对比分析这4种算法的性能。结果表明:与其他3种算法相比,采用SSFxLMS算法对高斯白噪声和簇绒地毯织机噪声进行控制时,误差信号的平均绝对值更小,平均降噪量与收敛速度也有大幅度提升。由此可知,SSFxLMS算法有效改善了FxLMS算法无法兼顾收敛速度和稳态误差的问题,研究结果为噪声主动控制算法设计提供了一定的参考。

基于改进变步长LMS算法的储能飞轮主动磁轴承-转子系统振动控制

针对储能飞轮主动磁轴承-转子系统的振动控制,在变步长最小均方差(LMS)算法的基础上采用一种改进的步长因子并对其可变参数和算法效果进行对比分析,改进算法在提高迭代收敛速度的同时还能保持一定的稳态误差。对基于有限铁木辛柯梁单元法建立的轴承-转子系统动力学模型的仿真结果表明,在转子的振动位移反馈信号进入控制器前,利用基于改进步长因子LMS算法的自适应滤波器可以有效识别并滤除与转子同频的信号分量,从而实现储能飞轮主动磁轴承-转子系统的不平衡振动控制。

Vibration Suppression for Active Magnetic Bearings Using Adaptive Filter with Iterative Search Algorithm

Active Magnetic Bearing(AMB) is a kind of electromagnetic support that makes the rotor movement frictionless and can suppress rotor vibration by controlling the magnetic force. The most common approach to restrain the rotor vibration in AMBs is to adopt a notch filter or adaptive filter in the AMB controller. However, these methods cannot obtain the precise amplitude and phase of the compensation current. Thus, they are not so effective in terms of suppressing the vibrations of the fundamental and other harmonic orders over the whole speed range. To improve the vibration suppression performance of AMBs,an adaptive filter based on Least Mean Square(LMS) is applied to extract the vibration signals from the rotor displacement signal. An Iterative Search Algorithm(ISA) is proposed in this paper to obtain the corresponding relationship between the compensation current and vibration signals. The ISA is responsible for searching the compensating amplitude and shifting phase online for the LMS filter, enabling the AMB controller to generate the corresponding compensation force for vibration suppression. The results of ISA are recorded to suppress vibration using the Look-Up Table(LUT) in variable speed range. Comprehensive simulations and experimental validations are carried out in fixed and variable speed range, and the results demonstrate that by employing the ISA, vibrations of the fundamental and other harmonic orders are suppressed effectively.

双曲正切函数的新型变步长LMS算法

针对自适应最小均方误差(Least Mean Square,LMS)滤波算法迭代步长在算法收敛速度、稳态误差间的折中问题,设计了一种基于双曲正切函数的新型变步长算法,算法以双曲正切函数为基础,建立步长因子μ(n)与误差信号e(n)的非线性函数关系,并引入参数α、β和m,设计了一种新的步长调整公式,使得在算法迭代初始阶段采用较大步长因子,达到更快的收敛速度,在接近收敛时采用较小的步长因子,获得更小的稳态误差。通过仿真分析了不同参数对算法性能的影响,与已有典型变步长算法相比,论文算法具有更快的收敛速度、更小的稳态误差和更优的追踪能力。

A novel dynamic step size LMS optimization scheme for interference reducing in FBMC-QAM

Filter bank multicarrier quadrature amplitude modulation(FBMC-QAM)will encounter inter-ference and noise during the process of channel transmission.In order to suppress the interference in the communication system,channel equalization is carried out at the receiver.Given that the con-ventional least mean square(LMS)equilibrium algorithm usually suffer from drawbacks such as the inability to converge quickly in large step sizes and poor stability in small step sizes when searching for optimal weights,in this paper,a design scheme for adaptive equalization with dynamic step size LMS optimization is proposed,which can further improve the convergence and error stability of the algorithm by calling the Sigmoid function and introducing three new parameters to control the range of step size values,adjust the steepness of step size,and reduce steady-state errors in small step sta-ges.Theoretical analysis and simulation results demonstrate that compared with the conventional LMS algorithm and the neural network-based residual deep neural network(Res-DNN)algorithm,the adopted dynamic step size LMS optimization scheme can not only obtain faster convergence speed,but also get smaller error values in the signal recovery process,thereby achieving better bit error rate(BER)performance.

基于LMS自适应滤波的雷达随队干扰抵消

随队干扰是雷达对抗中常用的干扰方式,通常通过遮盖目标回波信号而使雷达失去探测能力,因此需要加以抑制。随队干扰经常是非平稳的随机信号,在此情况下,文中利用最小均方(LMS)自适应滤波器得到干扰的估计并将其从雷达接收信号中消除,从而给出了一种基于LMS自适应滤波的雷达随队干扰抵消方法。首先,建立了雷达接收信号模型,包括主阵列天线接收信号和辅助阵元接收信号;然后,给出了基于LMS自适应滤波的干扰抵消原理,它实际上将辅助阵元接收信号输入自适应滤波器得到随队干扰估计,从主阵列天线接收信号中减去此干扰估计从而实现干扰抵消,通过分析抵消器的性能发现,除了辐射干扰的目标难以探测外,编队中其他目标的信干噪比都得到了提高;最后,给出了随队干扰抵消的仿真实例,验证了上述干扰抵消方法的良好效果。

A new method of lung sounds filtering using modulated least mean square—Adaptive noise cancellation

Advanced processing of lung sound (LS) recording is a significant means to separate heart sounds (HS) and combined low frequency noise from instruments (NI), with saving its characteristics. This paper proposes a new method of LS filtering which separates HS and NI simultaneously. It focuses on the application of least mean squares (LMS) algorithm with adaptive noise cancelling (ANC) technique. The second step of the new method is to modulate the reference input r1(n) of LMS-ANC to acquiesce combining HS and NI signals. The obtained signal is removed from primary signal (original lung sound recording-LS). The original signal is recorded from subjects and derived HS from it and it is modified by a band pass filter. NI is simulated by generating approximately periodic white gaussian noise (WGN) signal. The LMS-ANC designed algorithm is controlled in order to determine the optimum values of the order L and the coefficient convergence μ. The output results are measured using power special density (PSD), which has shown the effectiveness of our suggested method. The result also has shown visual difference PSD (to) normal and abnormal LS recording. The results show that the method is a good technique for heart sound and noise reduction from lung sounds recordings simultaneously with saving LS characteristics.

基于LMS滤波算法优化数控加工速度误差的应用

针对数控加工过程中速度误差导致加工精度低的问题,研究所加工零件的加工精度、切削加减速误差和切削加速度变化规律等,提出基于LMS滤波算法的数控加工速度误差优化。通过对非均匀有理B样条(NURBS)曲线进行仿真加工,对数控机床加工速度进行自适应控制。通过引入最小均方算法进行误差分析,从而提高插补速度精度,使数控机床加工误差降低、效率提高。通过实验测试对所提误差控制方法进行验证。结果表明:基于LMS滤波算法优化数控加工误差控制,不仅使数控机床加工速度得到提高,还有效解决了数控机床加工运动过程中存在的加工误差问题,使加工精度得到有效提升,证明所提加工误差控制方法具有一定可行性。

A Study of EM Algorithm as an Imputation Method: A Model-Based Simulation Study with Application to a Synthetic Compositional Data

Compositional data, such as relative information, is a crucial aspect of machine learning and other related fields. It is typically recorded as closed data or sums to a constant, like 100%. The statistical linear model is the most used technique for identifying hidden relationships between underlying random variables of interest. However, data quality is a significant challenge in machine learning, especially when missing data is present. The linear regression model is a commonly used statistical modeling technique used in various applications to find relationships between variables of interest. When estimating linear regression parameters which are useful for things like future prediction and partial effects analysis of independent variables, maximum likelihood estimation (MLE) is the method of choice. However, many datasets contain missing observations, which can lead to costly and time-consuming data recovery. To address this issue, the expectation-maximization (EM) algorithm has been suggested as a solution for situations including missing data. The EM algorithm repeatedly finds the best estimates of parameters in statistical models that depend on variables or data that have not been observed. This is called maximum likelihood or maximum a posteriori (MAP). Using the present estimate as input, the expectation (E) step constructs a log-likelihood function. Finding the parameters that maximize the anticipated log-likelihood, as determined in the E step, is the job of the maximization (M) phase. This study looked at how well the EM algorithm worked on a made-up compositional dataset with missing observations. It used both the robust least square version and ordinary least square regression techniques. The efficacy of the EM algorithm was compared with two alternative imputation techniques, k-Nearest Neighbor (k-NN) and mean imputation (), in terms of Aitchison distances and covariance.

基于LMS算法的短波通信数据干扰控制技术

短波通信原理简单,已广泛应用于大型无线通信系统。但在实际应用中,很多因素会影响短波通信,造成数据干扰,因此应采取有效的控制措施。基于此,分析短波通信的基本内容与主要特点,并在剖析短波通信干扰的基础上,分别从短波通信信号特征提取、干扰数据识别、数据干扰控制及实验测试4个方面,探讨基于最小均方(Least Mean Square,LMS)的短波通信数据干扰控制技术。

改善的LMS自适应算法在TDLAS甲烷检测的降噪研究

为进一步有效抑制检测系统的噪声,提高检测精度,研究了改善的最小均方差自适应算法在可调谐二极管激光吸收光谱甲烷浓度检测系统的降噪方法。通过基于TDLAS技术的matlab仿真实验,搭建的甲烷检测系统,选取1 653.72 nm的甲烷吸收峰位,分析LMS自适应算法中滤波阶数、步长因子和采样周期三者对噪声的关系,改善参数的选取以最佳的滤波效果进行降噪优化处理。研究表明在高频采样时刻收敛到最佳的滤波阶数和步长因子可对系统起到最优滤波效果。研究结果显示信噪比有效提升了94%,拟合优度R~2达到0.997,证明改善的LMS自适应滤波算法可以有效抑制噪声对二次谐波信号的影响。

基于优化模糊C-means算法的不平衡大数据分类研究

针对不平衡大数据的分类问题,提出一种优化模糊C-means算法的不平衡大数据分类算法。先计算C-means模糊交叉算子,定义优化函数,并求解大数据不平衡增益。利用Spark分类平台,确定大数据样本压缩模糊近邻值的取值范围,再通过放大近邻值的处理方式,定义不平衡阈向量,从而完善整个分类流程,完成基于优化模糊C-means算法的不平衡大数据分类方法的设计。实验结果表明,上述分类方法的应用,可将正例信息、负例信息的取样长度区间完全分离开来,能有效解决因不平衡大数据分类不精准造成的信息样本混淆的问题,符合实际应用需求。

基于LMS自适应滤波器的PMSM谐波抑制方法

为有效抑制电流谐波,在原有的PI控制器基础上,基于最小均方自适应滤波器(LMS-ANF)改造控制器结构,使得永磁同步电机特定次电流谐波得到抑制。通过在传统d,q坐标系矢量控制算法的基础上增加自适应滤波器模块,将采样得到的实际电流作为输入,提取、放大实际电流中的特定次谐波电流,通过PI调节器对谐波误差放大后的电流进行调节,得到控制电压,取得了良好的谐波抑制效果。通过仿真以及台架实验,证明了该控制策略对于抑制电流谐波的有效性。

MI-NLMS adaptive beamforming algorithm for smart antenna system applications

A Matrix Inversion Normalized Least Mean Square (MI-NLMS) adaptive beamforming algorithm was developed for smart antenna application. The MI-NLMS which combined the individual good aspects of Sample Matrix Inversion (SMI) and the Normalized Least Mean Square (NLMS) algorithms is described. Simulation results showed that the less complexity MI-NLMS yields 15 dB improvements in interference suppression and 5 dB gain enhancement over LMS algorithm, converges from the initial iteration and achieves 24% BER improvements at cochannel interference equal to 5. For the case of 4-element uniform linear array antenna, MI-NLMS achieved 76% BER reduction over LMS algorithm.

Cancellation for frequency offset in OFDM system based on TF-LMS algorithm

In an orthogonal frequency division multiplexing(OFDM) system,a time and frequency domain least mean square algorithm(TF-LMS) was proposed to cancel the frequency offset(FO).TF-LMS algorithm is composed of two stages.Firstly,time domain least mean square(TD-LMS) scheme was selected to pre-cancel the frequency offset in the time domain,and then the interference induced by residual frequency offset was eliminated by the frequency domain mean square(FD-LMS) scheme in frequency domain.The results of bit error rate(BER) and quadrature phase shift keying(QPSK) constellation figures show that the performance of the proposed suppression algorithm is excellent.

Active micro-vibration control based on improved variable step size LMS algorithm

The contradiction of variable step size least mean square(LMS)algorithm between fast convergence speed and small steady-state error has always existed.So,a new algorithm based on the combination of logarithmic and symbolic function and step size factor is proposed.It establishes a new updating method of step factor that is related to step factor and error signal.This work makes an analysis from 3 aspects:theoretical analysis,theoretical verification and specific experiments.The experimental results show that the proposed algorithm is superior to other variable step size algorithms in convergence speed and steady-state error.