Structural design of mid-infrared waveguide detectors based on InAs/GaAsSb superlattice

In the realm of near-infrared spectroscopy,the detection of molecules has been achieved using on-chip waveguides and resonators.In the mid-infrared band,the integration and sensitivity of chemical sensing chips are often constrained by the reliance on off-chip light sources and detectors.In this study,we demonstrate an InAs/GaAsSb superlattice mid-infrared waveguide integrated detector.The GaAsSb waveguide layer and the InAs/GaAsSb superlattice absorbing layer are connected through evanescent coupling,facilitating efficient and highquality detection of mid-infrared light with minimal loss.We conducted a simulation to analyze the photoelectric characteristics of the device.Additionally,we investigated the factors that affect the integration of the InAs/GaAs⁃Sb superlattice photodetector and the GaAsSb waveguide.Optimal thicknesses and lengths for the absorption lay⁃er are determined.When the absorption layer has a thickness of 0.3μm and a length of 50μm,the noise equiva⁃lent power reaches its minimum value,and the quantum efficiency can achieve a value of 68.9%.The utilization of waveguide detectors constructed with Ⅲ-Ⅴ materials offers a more convenient means of integrating mid-infra⁃red light sources and achieving photoelectric detection chips.

Singular optical propagation properties of two types of one-dimensional anti-PT-symmetric periodic ring optical waveguide networks

Two types of one-dimensional(1D)anti-PT-symmetric periodic ring optical waveguide networks,consisting of gain and loss materials,are constructed.The singular optical propagation properties of these networks are investigated.The results show that the system composed of gain materials exhibits characteristics of ultra-strong transmission and bidirectional reflection.Conversely,the system composed of loss materials demonstrates equal transmittance and reflectance at some frequencies.In both the systems,a new type of total reflection phenomenon is observed.When the imaginary part of the refractive indices of waveguide segments is smaller than 10-5,the system shows bidirectional transparency with the transmittance tending to be 1 and reflectivity to be smaller than 10-8 at some bands.When the refractive indices of the waveguide segments are real,the system will be bidirectional transparent at the full band.These findings may deepen the understanding of anti-PT-symmetric optical systems and optical waveguide networks,and possess potential applications in efficient optical energy storage,ultra-sensitive optical filters,ultra-sensitive all-optical switches,integrated optical chips,stealth physics,and so on.

Simultaneous guidance of electromagnetic and elastic waves via glide symmetry phoxonic crystal waveguides

A phoxonic crystal waveguide with the glide symmetry is designed,in which both electromagnetic and elastic waves can propagate along the glide plane at the same time.Due to the glide symmetry,the bands of the phoxonic crystal super-cell degenerate in pairs at the boundary of the Brillouin zone.This is the so-called band-sticking effect and it causes the appearance of gapless guided-modes.By adjusting the magnitude of the glide dislocation the edge bandgaps,the bandgap of the guided-modes at the boundary of the Brillouin zone,can be further adjusted.The photonic and phononic guided-modes can then possess only one mode for a certain frequency with relatively low group velocities,achieving single-mode guided-bands with relatively flat dispersion relationship.In addition,there exists acousto-optic interaction in the cavity constructed by the glide plane.The proposed waveguide has potential applications in the design of novel optomechanical devices.

Asymptotic analysis on bright solitons and breather solutions of a generalized higher-order nonlinear Schrödinger equation in an optical fiber or a planar waveguide

We study a generalized higher-order nonlinear Schr¨odinger equation in an optical fiber or a planar waveguide.We obtain the Lax pair and N-fold Darboux transformation(DT)with N being a positive integer.Based on Lax pair obtained by us,we derive the infinitely-many conservation laws.We give the bright one-,two-,and N-soliton solutions,and the first-,second-,and Nth-order breather solutions based on the N-fold DT.We conclude that the velocities of the bright solitons are influenced by the distributed gain function,g(z),and variable coefficients in equation,h1(z),p1(z),r1(z),and s1(z)via the asymptotic analysis,where z represents the propagation variable or spatial coordinate.We also graphically observe that:the velocities of the first-and second-order breathers will be affected by h1(z),p1(z),r1(z),and s1(z),and the background wave depends on g(z).

Single-photon scattering and quantum entanglement of two giant atoms with azimuthal angle differences in a waveguide system

We theoretically investigate coherent scattering of single photons and quantum entanglement of two giant atoms with azimuthal angle differences in a waveguide system.Using the real-space Hamiltonian,analytical expressions are derived for the transport spectra scattered by these two giant atoms with four azimuthal angles.Fano-like resonance can be exhibited in the scattering spectra by adjusting the azimuthal angle difference.High concurrence of the entangled state for two atoms can be implemented in a wide angle-difference range,and the entanglement of the atomic states can be switched on/off by modulating the additional azimuthal angle differences from the giant atoms.This suggests a novel handle to effectively control the single-photon scattering and quantum entanglement.

Unveiling the in-plane anisotropic dielectric waveguide modes in α-MoO_(3) flakes

The unique in-plane and out-of-plane anisotropy of α-MoO_(3) has attracted considerable interest with regard to potential optoelectronic applications. However, most research has focused on the mid-infrared spectrum, leaving its properties and applications in the visible and near-infrared light spectrum less explored. This study advances the understanding of waveguiding properties of α-MoO_(3) by near-field imaging of the waveguide modes along the [100] and [001] directions of α-MoO_(3) flakes at 633 nm and 785 nm. We investigate the effects of flake thickness and documented the modes' dispersion relationships, which is crucial for tailoring the optical responses of α-MoO_(3) in device applications. Our findings enhance the field of research into α-MoO_(3), highlighting its utility in fabricating next-generation optoelectronic devices due to its unique optically anisotropic waveguide.

Super energy flows in a waveguide filled with air and left-handed materials

The phenomena of super energy flows are studied theoretically and numerically in a parallel-plate waveguide which is filled with two layered equally-thick different media, i.e. air and specific left-handed materials （LHM） with εr1 = -1/（1 ＋δ） ＋iγ and μr1 = -（1 ＋ δ） ＋ iγ. In this special waveguide, two-directional super-energy flows are excited by a three-dimensional horizontal electric dipole at the same time, which has transmission patterns different from those of two-dimensional source and three-dimensional vertical electric dipole. We also show that the retardation and loss in LHM are sensitive to the amplitude of super power densities, and the dimensions of waveguide determine the propagating modes, which makes super energy flows more practical.

Generation of broadband polarization-orthogonal photon pairs via the dispersion-engineered thin-film lithium niobate waveguide

Broadband photon pairs are highly desirable for quantum metrology,quantum sensing,and quantum communication.Such sources are usually designed through type-0 phase-matching spontaneous parametric down-conversion(SPDC)that makes the photon pairs hard to separate in the frequency-degenerate case and thus limits their applications.In this paper,we design a broadband frequency-degenerate telecom-band photon pair source via the type-II SPDC in a dispersion-engineered thin-film lithium niobate waveguide,where the polarization modes of photon pairs are orthogonal and thus are easily separated deterministically.With a 5-mm-long waveguide,our design can achieve a bandwidth of 5.56 THz(44.8 nm),which is 8.6 times larger than that of the bulk lithium niobate,and the central wavelength can be flexibly adjusted.Our design is a promising approach towards high-quality integrated photon sources and may have wide applications in photonic quantum technologies.

Monolithically Integrating a 180° Bent Waveguide into a III-Nitride Optoelectronic On-Chip System

GaN-based devices have developed significantly in recent years due to their promising applications and research potential.A major goal is to monolithically integrate various GaN-based components onto a single chip to create future optoelectronic systems with low power consumption.This miniaturized integration not only enhances multifunctional performance but also reduces material,processing,and packaging costs.In this study,we present an optoelectronic on-chip system fabricated using a top-down approach on a III-nitride-on-silicon wafer.The system includes a near-ultraviolet light source,a monitor,a 180°bent waveguide,an electro-absorption modulator,and a receiver,all integrated without the need for regrowth or post-growth doping.35 Mbit/s optical data communication is demonstrated through light propagation within the system,confirming its potential for compact GaN-based optoelectronic solutions.

Selective Impact of Dispersion and Nonlinearity on Waves and Solitary Wave in a Strongly Nonlinear and Flattened Waveguide

The waveguide which is at the center of our concerns in this work is a strongly flattened waveguide, that is to say characterized by a strong dispersion and in addition is strongly nonlinear. As this type of waveguide contains multiple dispersion coefficients according to the degrees of spatial variation within it, our work in this article is to see how these dispersions and nonlinearities each influence the wave or the signal that can propagate in the waveguide. Since the partial differential equation which governs the dynamics of propagation in such transmission medium presents several dispersion and nonlinear coefficients, we check how they contribute to the choices of the solutions that we want them to verify this nonlinear partial differential equation. This effectively requires an adequate choice of the form of solution to be constructed. Thus, this article is based on three main pillars, namely: first of all, making a good choice of the solution function to be constructed, secondly, determining the exact solutions and, if necessary, remodeling the main equation such that it is possible;then check the impact of the dispersion and nonlinear coefficients on the solutions. Finally, the reliability of the solutions obtained is tested by a study of the propagation. Another very important aspect is the use of notions of probability to select the predominant solutions.

Active Cancelation of Acoustic Noise in Waveguides by Standard Control Task Decision Usage

Cybernetic decision variants were analyzed in order to use for physical task of active noise cancelation. 10 dB mean active noise cancellation is demonstrated in two decades frequency band by usage of cybernetic decision for acoustical duct physical scale model. The used decision was found on minimization of acoustical field power transfer function from the beginning of waveguide to their end.

Wave propagation in parallel-plate waveguides filled with nonlinear left-handed material

A theoretical investigation of field components for transverse electric mode in the parallel-plate waveguides has been studied. In this analysis two different types of waveguide structures have been discussed, i.e., （a） normal good/perfect conducting parallel-plate waveguide filled with nonlinear left-handed material and （b） high-temperature-superconducting parallel-plate waveguide filled with nonlinear left-handed material. The dispersion relations of transverse electric mode have also been discussed for these two types of waveguide structures.

Influence of Waveguide Properties on Wave Prototypes Likely to Accompany the Dynamics of Four-Wave Mixing in Optical Fibers

In this article, we study the impacts of nonlinearity and dispersion on signals likely to propagate in the context of the dynamics of four-wave mixing. Thus, we use an indirect resolution technique based on the use of the iB-function to first decouple the nonlinear partial differential equations that govern the propagation dynamics in this case, and subsequently solve them to propose some prototype solutions. These analytical solutions have been obtained;we check the impact of nonlinearity and dispersion. The interest of this work lies not only in the resolution of the partial differential equations that govern the dynamics of wave propagation in this case since these equations not at all easy to integrate analytically and their analytical solutions are very rare, in other words, we propose analytically the solutions of the nonlinear coupled partial differential equations which govern the dynamics of four-wave mixing in optical fibers. Beyond the physical interest of this work, there is also an appreciable mathematical interest.

Waveguide Bragg Grating for Fault Localization in PON

Femtosecond laser direct inscription is a technique especially useful for prototyping purposes due to its distinctive advantages such as high fabrication accuracy,true 3D processing flexibility,and no need for mold or photomask.In this paper,we demonstrate the design and fabrication of a planar lightwave circuit(PLC)power splitter encoded with waveguide Bragg gratings(WBG)using a femtosecond laser inscription technique for passive optical network(PON)fault localization application.Both the reflected wavelengths and intervals of WBGs can be conveniently tuned.In the experiment,we succeeded in directly inscribing WBGs in 1×4 PLC splitter chips with a wavelength interval of about 4 nm and an adjustable reflectivity of up to 70% in the C-band.The proposed method is suitable for the prototyping of a PLC splitter encoded with WBG for PON fault localization applications.

Guided Modes in a Four-Layer Slab Waveguide with Dispersive Left-Handed Material

A four-layer slab waveguide including left-handed material is investigated numerically in this paper. Considering left-handed material dispersion, we find eight TE guided modes as frequency from 4 GHz to 6 GHz. The fundamental mode can exist, and its dispersion curves are insensitive to the waveguide thickness. Besides, the total power fluxes of TE guided modes are analyzed and corresponding new properties are found, such as: positive and negative total power fluxes coexist;at maximum value of frequency, we find zero total power flux, etc. Our results may be of benefit to the optical waveguide technology.

TM modes in asymmetric slab waveguides with left-handed material

Three-layer slab waveguide with left-handed materials （LHM） is discussed using the Maxwell＇s equations and their equations of dispersion relation for TM modes are obtained. By seeking the power of the slab waveguide, their equations of effective thickness for TM modes are obtained. Furthermore, the interrelated equations for right-handed materials （RHM） slab waveguide are introduced and their curves plotted. To find new properties for LHM slab waveguide, the equations and their curves for the LHM and RHM slab waveguide are compared respectively.

Experimental observation of topological large-area pseudo-spin-momentum-locking waveguide states with exceptional robustness

Unlike conventional topological edge states confined at a domain wall between two topologically distinct media,the recently proposed large-area topological waveguide states in three-layer heterostructures,which consist of a domain featuring Dirac points sandwiched between two domains of different topologies,have introduced the mode width degree of freedom for more flexible manipulation of electromagnetic waves.Until now,the experimental realizations of photonic large-area topological waveguide states have been exclusively based on quantum Hall and quantum valley-Hall systems.We propose a new way to create large-area topological waveguide states based on the photonic quantum spin-Hall system and observe their unique feature of pseudo-spin-momentum-locking unidirectional propagation for the first time in experiments.Moreover,due to the new effect provided by the mode width degree of freedom,the propagation of these large-area quantum spin-Hall waveguide states exhibits unusually strong robustness against defects,e.g.,large voids with size reaching several unit cells,which has not been reported previously.Finally,practical applications,such as topological channel intersection and topological energy concentrator,are further demonstrated based on these novel states.Our work not only completes the last member of such states in the photonic quantum Hall,quantum valley-Hall,and quantum spin-Hall family,but also provides further opportunities for high-capacity energy transport with tunable mode width and exceptional robustness in integrated photonic devices and on-chip communications.

High Power 808nm AlGaAs/GaAs Quantum Well Laser Diodes with Broad Waveguide

The 808nm laser diodes with a broad waveguide are designed and fabricated.The thickness of the Al_ 0.35 - Ga_ 0.65 As waveguide is increased to 0.9μm.In order to suppress the super modes,the thickness of the Al_ 0.55 Ga_ 0.45 As cladding layers is reduced to only 0.7μm while keeping the transverse radiation losses of the fundamental mode below 0.2cm -1 .The structures are grown by metal organic chemical vapour deposition.The devices show excellent performances.The maximum output power of 10.2W in the 100μm broad-area laser diodes is obtained.

Ridge Waveguide Electro-Optic Polymer Modulator with a New Kind of Corona Poled Crosslinkable Polyurethane

A polymer electro optic modulator has been fabricated with the functional layer acting as a kind of corona poled crosslinkable polyurethane. The three optical layers, namely waveguide, photolithography and oxygen are fabricated by spin coating. With the Reactive Ion Etching method, the ridge of the waveguide is constructed. With light at 1 31μm being fiber coupled to waveguide, the mode and the modulation properties of these devices are demonstrated in a micron control system.

Low-Microwave Loss Coplanar Waveguides Fabricated on High-Resistivity Silicon Substrate

Three kinds of coplanar waveguides （CPWs） are designed and fabricated on different silicon substrates---common low-resistivity silicon substrate （LRS）, LRS with a 3μm-thick silicon oxide interlayer, and high-resistivity silicon （HRS） substrate. The results show that the microwave loss of a CPW on LRS is too high to be used, but it can be greatly reduced by adding a thick interlayer of silicon oxide between the CPW transmission lines and the LRS.A CPW directly on HRS shows a loss lower than 2dB/cm in the range of 0-26GHz and the process is simple,so HRS is a more suitable CPW substrate.