Internal quantum efficiency drop induced by the heat generation inside of light emitting diodes (LEDs)

The reasons for low output power of AlGalnP Light Emitting Diodes （LEDs） have been analysed. LEDs with AlGaInP material have high internal but low external quantum efficiency and much heat generated inside especially at a large injected current which would reduce both the internal and external quantum efficiencies. Two kinds of LEDs with the same active region but different window layers have been fabricated. The new window layer composed of textured 0.5 μm GaP and thin Indium-Tin-Oxide film has shown that low external quantum efficiency （EQE） has serious impaction on the internal quantum efficiency （IQE）, because the carrier distribution will change with the body temperature increasing due to the heat inside, and the test results have shown the evidence of LEDs with lower output power and bigger wavelength red shift.

Controlled Growth of Large-Area Aligned Single-Crystalline Organic Nanoribbon Arrays for Transistors and Light-Emitting Diodes Driving

Organic field-effect transistors(OFETs) based on organic micro-/nanocrystals have been widely reported with charge carrier mobility exceeding 1.0 cm^2V^(-1)s^(-1), demonstrating great potential for high-performance, low-cost organic electronic applications. However, fabrication of large-area organic micro-/nanocrystal arrays with consistent crystal growth direction has posed a significant technical challenge. Here, we describe a solution-processed dip-coating technique to grow large-area, aligned 9,10-bis(phenylethynyl) anthracene(BPEA) and 6,13-bis(triisopropylsilylethynyl) pentacene(TIPSPEN) single-crystalline nanoribbon arrays. The method is scalable to a 5 9 10 cm^2 wafer substrate, with around 60% of the wafer surface covered by aligned crystals. The quality of crystals can be easily controlled by tuning the dip-coating speed. Furthermore, OFETs based on well-aligned BPEA and TIPS-PEN single-crystalline nanoribbons were constructed.By optimizing channel lengths and using appropriate metallic electrodes, the BPEA and TIPS-PEN-based OFETs showed hole mobility exceeding 2.0 cm^2V^(-1)s^(-1)(average mobility 1.2 cm^2V^(-1)s^(-1)) and 3.0 cm^2V^(-1)s^(-1)(average mobility2.0 cm^2V^(-1)s^(-1)), respectively. They both have a high on/off ratio(I_(on)/I_(off))>10~9. The performance can well satisfy the requirements for light-emitting diodes driving.

Very-High Color Rendering Index Hybrid White Organic Light-Emitting Diodes with Double Emitting Nanolayers

A very-high color rendering index white organic light-emitting diode(WOLED) based on a simple structure was successfully fabricated. The optimized device exhibits a maximum total efficiency of 13.1 and 5.4 lm/W at 1,000 cd/m2. A peak color rendering index of 90 and a relatively stable color during a wide range of luminance were obtained. In addition, it was demonstrated that the 4,40,400-tri(9-carbazoyl) triphenylamine host influenced strongly the performance of this WOLED.These results may be beneficial to the design of both material and device architecture for high-performance WOLED.

Synthesis and luminescent properties of polycrystalline Gd_2(MoO_4)_3:Dy^(3+) for white light-emitting diodes

Polycrystalline Gd2(MoO4)3:Dy3+ phosphors have been synthesized by high temperature solid-state reaction method. The phosphors were characterized with X-ray diffractometer, thermogravimetric analysis and different scanning calorimeter, scanning electron microscopy, and photoluminescence spectrofluorimeter. Several peaks at 351, 389, 425, 452, and 472 nm appeared in photoluminescence excitation spectrum, which matched well with the emission of the ultraviolet (UV) and blue-light emitting diode (LED) chips. Upon excitation at 389 nm UV light, intense emissions centered at 484, 575 and 668 nm were attributed to the transitions of 4F9/2→6H15/2, 4F9/2→6H13/2 and 4F9/2→6H11/2 of Dy3+, respectively. The chromaticity coordinates and correlative color temperatures have been calculated and presented in the Commission International de I’Eclairage (CIE) diagrams. The results indicated that Gd1.9(MoO4)3:Dy0.13+ with CIE coordinates of (x=0.38, y=0.41) and the correlative color temperature of 4134 K is a potential candidate for white LEDs.

Review of blue perovskite light emitting diodes with optimization strategies for perovskite film and device structure

Perovskite light emitting diodes(PeLEDs)have attracted considerable research attention because of their external quantum efficiency(EQE)of>20%and have potential scope for further improvement.However,compared to red and green PeLEDs,blue PeLEDs have not been extensively investigated,which limits their commercial applications in the fields of luminance and full-color displays.In this review,blue-PeLED-related research is categorized by the composition of perovskite.The main challenges and corresponding optimization strategies for perovskite films are summarized.Next,the novel strategies for the design of device structures of blue PeLEDs are reviewed from the perspective of transport layers and interfacial layers.Accordingly,future directions for blue PeLEDs are discussed.This review can be a guideline for optimizing perovskite film and device structure of blue PeLEDs,thereby enhancing their development and application scope.

Metal–organic–vapor phase epitaxy of InGaN quantum dots and their applications in light-emitting diodes

InGaN quantum dot is a promising optoelectronic material, which combines the advantages of low-dimensional and wide-gap semiconductors. The growth of InGaN quantum dots is still not mature, especially the growth by metal--organic- vapor phase epitaxy （MOVPE）, which is challenge due to the lack of, itin-situ monitoring tool. In this paper, we reviewed the development of InGaN quantum dot growth by MOVPE, including our work on growth of near-UV, green, and red InGaN quantum dots. In addition, we also introduced the applications of InGaN quantum dots on visible light emitting diodes.

Potential red-emitting phosphor GdNbO_4:Eu^(3+),Bi^(3+) for near-UV white light emitting diodes

A red-emitting phosphor GdNbO4：Eu3＋,Bi3＋ was prepared by a high temperature solid-state reaction technique. The phosphor was characterized by X-ray diffraction （XRD）, particle size analyzer and fluorescence spectrometer. The single phase of GdNbO4：Eu3＋,Bi3＋ was obtained at 1150~C and the average particle diameter was about 2.30 μm. Excitation and emission spectra reveal that the phosphor can be ef- ficiently excited by ultraviolet （UV） light （394 nm） and emit the strong red light of 612 nm due to the Eu3＋ transition of SD0~TF2. The opti- mum content of Eu3＋ doped in the phosphor GdNbOn：Eu3＋ is 20mo1%. The phosphor Gdo.80NbO4：0.20Eu3＋,0.03Bi3＋ shows much stronger photoluminescence intensity and better chromaticity coordinates （x=0.642, 0.352） than GdNbO4：Eu3＋. It is confirmed that Gdo.80NbO4：0.20Eu3＋,0.03Bi3＋ is a potential candidate for near-UV chip-based white light emitting diodes.

Near-infrared lead chalcogenide quantum dots:Synthesis and applications in light emitting diodes

This paper reviews the recent progress in the synthesis of near-infrared(NIR) lead chalcogenide(PbX;PbX = PbS,PbSe, PbTe) quantum dots(QDs) and their applications in NIR QDs based light emitting diodes(NIR-QLEDs). It summarizes the strategies of how to synthesize high efficiency PbX QDs and how to realize high performance Pb X based NIR-QLEDs.

PEROVSKITE SEMICONDUCTOR OPTOELECTRONIC DEVICES Rational molecular passivation for high-performance perovskite light-emitting diodes

Solution-processed metal halide perovskites (MHPs) have received significant interest for cost-effective, high-performance optoelectronic devices. In addition to the great successes in photovoltaics, their excellent luminescence and charge transport properties also make them promising for light emitting diodes (LEDs). To achieve high-efficiency perovskite LEDs (PeLEDs), extensive efforts have been carried out to enhance radiative recombination rates by confining the electrons and holes. In addition to enhancing radiative recombination rates, it is equally important to decrease the non-radiative recombination for improving the device performance. Passivation of the defects could be an efficient way for reducing the non-radiative recombination.

Organic Light Emitting Diodes with Lithium Contained Alq3 as Electron Injection Layer

lNovel lithium doped tris 8 hydroxylquinoline aluminium(Alq3:Li) layer is deposited between emission layer and electron injection aluminium electrode as an electron injection assistant layer in different organic light emitting diodes(OLED) to lower the electron injection barrier. In these devices, Alq3 is used as emission layer, and a bilayer film of N,N bis (1 naphhyl) N,N diphenyl 1,1 biphenyle 4,4' diamine(NPB) and 4,4,4' tris(3 methyl phenylphenylamino) triphenylamine( m MTDATA) used as hole transport layer(HTL). The electroluminescent performance of devices with different thicknesses of Alq3∶Li shows that the insertion of the lithium doped Alq3 layer can reduce the turn on voltage by at least 2 volts, and the stability of devices with this lithium doped Alq3 layer is improved too. It can also change the efficiency of devices. Compared with an ultra thin lithium fluoride(LiF) layer, Alq3∶Li sheet gives similar effects but higher efficiency and can be much thicker and hence it is easier to control the deposition.

Organic light emitting diodes using magnesium doped organic acceptor as electron injection layer and silver as cathode

Organic light emitting diodes employing magnesium doped electron acceptor 3, 4, 9, 10 perylenetetracarboxylic dianhydride （Mg：PTCDA） as electron injection layer and silver as cathode were demonstrated. As compared to Mg ： Ag cathode, the combination of the Mg ： PTCDA layer and silver provided enhanced electron injection into tris （8- quinolinolato） aluminium. The device with 1 ： 2 Mg ： PTCDA and Ag showed an increase of about 12% in the maximum current efficiency, mainly due to the improved hole-electron balance, and an increase of about 28% in the maximum power efficiency, as compared to the control device using Mg ： Ag cathode. The properties of Mg ： PTCDA composites were studied as well.

Temperature effects on photoluminescence of YAG:Ce^(3+) phosphor and performance in white light-emitting diodes

The well crystalline YAG：Ce^3＋ phosphor was synthesized by sold-state method, and the temperature dependence of excitation and emission spectra of YAG：Ce^3＋ phosphor were investigated in the temperature range from room temperature to 573 K. With temperature increasing, it was noted that the emission intensity of as-repared phosphors decreased considerably more rapidly when pumped by 460 nm than by 340 nm. The temperature-intensity curves under different excitation wavelengths were obtained using an Arrhenius function, and the corresponding activation energies were also obtained respectively. Thus, the experimental phenomenon was discussed in terms of nonradiative decay rate. The effects of as-prepared phosphors on the performance of the white LED with changing temperature were also studied.

Simulation on effect of metal/graphene hybrid transparent electrode on characteristics of GaN light emitting diodes

In order to decrease the Schottky barrier height and sheet resistance between graphene （Gr） and the p-GaN layers in GaN-based light-emitting diodes （LEDs）, some transparent thin films with good conductivity and large work function are essential to insert into Gr and p-GaN layers. In this work, the ultra-thin films of four metals （silver （Ag）, golden （Au）, nickel （Ni）, platinum （Pt）） are explored to introduce as a bridge layer into Gr and p-GaN, respectively. The effect of a different combination of Gr/metal transparent conductive layers （TCLs） on the electrical, optical, and thermal characteristics of LED was investigated by the finite element methods. It is found that both the TCLs transmittance and the surface temperature of the LED chip reduces with the increase of the metal thickness, and the transmittance decreases to about 80% with the metal thickness increasing to 2 nm. The surface temperature distribution, operation voltage, and optical output power of the LED chips with different metal/Gr combination were calculated and analyzed. Based on the electrical, optical, and thermal performance of LEDs, it is found that 1.5-nm Ag or Ni or Pt, but 1-nm Au combined with 3 layered （L） Gr is the optimal Gr/metal hybrid transparent and current spreading electrode for ultra-violet （UV） or near-UV LEDs.

A recent advances of blue perovskite light emitting diodes for next generation displays

The halide perovskite blue light emitting diodes(PeLEDs)attracted many researchers because of its fascinating optoelectrical properties.This review introduces the recent progress of blue PeLEDs which focuses on emissive layers and interlayers.The emissive layer covers three types of perovskite structures:perovskite nanocrystals(PeNCs),2-dimensional(2D)and quasi-2D perovskites,and bulk(3D)perovskites.We will discuss about the remaining challenges of blue PeLEDs,such as limited performances,device instability issues,which should be solved for blue PeLEDs to realize next generation displays.

Effect of light-emitting diodes with different color rendering indexes on the ocular tissues of rat

AIM:To compare the damage of light-emitting diodes(LEDs)with different color rendering indexes(CRIs)to the ocular surface and retina of rats.METHODS:Totally 20 Sprague-Dawley(SD)rats were randomly divided into four groups:the first group was normal control group without any intervention,other three groups were exposed by LEDs with low(LED-L),medium(LED-M),and high(LED-H)CRI respectively for 12 h a day,continuously for 4 wk.The changes in tear secretion(Schirmer I test,SIt),tear film break-up time(BUT),and corneal fluorescein sodium staining(CFS)scores were compared at different times(1 d before experiment,2 and 4 wk after the experiment).The histopathological changes of rat lacrimal gland and retina were observed at 4 wk,and the expressions of tumor necrosis factor-α(TNF-α)and interleukin-6(IL-6)in lacrimal gland were detected by immunofluorescence method.RESULTS:With the increase of light exposed time,the CFS value of each light exposed group continued to increase,and the BUT and SIt scores continued to decrease,which were different from the control group,and the differences between the light exposed groups were statistically significant.Hematoxylin-eosin(HE)results showed that the lacrimal glands of each exposed group were seen varying degrees of acinar atrophy,vacuoledistribution,increasing of eosinophil granules,etc.;the retina showed obvious reduction of photoreceptor cell layer and changes in retinal thickness;LED-L group has the most significant change in all tests.Immunofluorescence suggested that the positive expressions of TNF-αand IL-6 in the lacrimal glands of each exposed group were higher than those of the control group.CONCLUSION:LED exposure for 4 wk can cause the pathological changes of lacrimal gland and retina of rats,and increase the expression of TNF-αand IL-6 in lacrimal gland,the degree of damage is negatively correlated with the CRI.

Improved blue quantum dot light-emitting diodes via chlorine passivated ZnO nanoparticle layer

In blue quantum dot light emitting diodes(QLEDs),electron injection is insufficient,which would degrade device efficiency and stability.Herein,we employ chlorine passivated ZnO nanoparticles as electron transport layer to facilitate electron injection into QDs effectively.Moreover,it suppresses exciton quenching at the QD/ZnO interface by blocking charge transfer channel.As a result,the maximum external quantum efficiency of blue QLED was increased from 2.55%to 4.60%,and the operation lifetime of blue QLED was nearly 4 times longer than that of the control device.Our work indicates that election injection plays an important role in blue QLED efficiency and stability.

Efficiency droop alleviation in blue light emitting diodes using the InGaN/GaN triangular-shaped quantum well

The InGaN/GaN blue light emitting diode（LED） is numerically investigated using a triangular-shaped quantum well model,which involves analysis on its energy band,carrier concentration,overlap of electron and hole wave functions,radiative recombination rate,and internal quantum efficiency.The simulation results reveal that the InGaN/GaN blue light emitting diode with triangular quantum wells exhibits a higher radiative recombination rate than the conventional light emitting diode with rectangular quantum wells due to the enhanced overlap of electron and hole wave functions（above 90%） under the polarization field.Consequently,the efficiency droop is only 18% in the light emitting diode with triangular-shaped quantum wells,which is three times lower than that in a conventional LED.

New Rare-Earth Containing (Sr_(1-y)Eu_y)_2Al_2Si_(10)N_(14)O_4 Phosphors for Light-Emitting Diodes

Remarkable progress was made in the development of white-light-emitting diodes （LEDs）. White LEDs provided a light element having a semiconductor InGaN light-emitting chip （blue or UV LEDs） and luminescent phosphors. Here we reported the sialon s-phase of （Sr,Eu）2A12Si10N14O4. Eu^2＋ activator ions that were substituted for the strontium site represented a new type of yeUow-green phosphor that could be excited by blue LEDs used for application in the fabrication of white LEDs.

Effects of light-emitting diodes on tissue culture plantlets and seedlings of rice (Oryza sativa L.)

Light-emitting diodes(L EDs)are a new light source with low energy consumption and high photoelectric conversion efficiency,and they can satisfy the energy-saving needs of plant culture systems.However,the effects of LED light sources on rice tissue culture and rice seedling cultivation are poorly understood.This study aimed to evaluate the effects of LEDs on the growth of tissue culture plantlets and seedlings of the rice(Oryza sativa L.)cultivar Nipponbare.The best light source for rice tissue culture was different from that for rice seedling cultivation.Blue(B)LED light was the most appropriate light for rice tissue culture.Under a B LED light,the time required for callus proliferation,differentiation and regeneration was the shortest,and the frequency of plantlet ititin,dfferetiation and regeneration was the highest.Ablue:red(B:R)=1:1LED light facilitated the growth of rice seedlings and produced the highest chlorophyll and carotenoid contents and photosynthetic rates in the rice seedlings.Abundant photosynthetic products were more effectively generated in the rice seedlings under the B:R=1:1 LED and R LED lights than under the B LED light.B LED light is the most appropriate light for rice tissue culture plantlets and can be used as an alternative light source for rice tissue culture,and B:R=1:1 LED light facilitated the cultivation of robust rice seedlings and can be used as the primary light source for rice factory seedling cultivation.

Simulation study of blue InGaN multiple quantum well light-emitting diodes with different hole injection layers

InGaN-based light-emitting diodes with p-GaN and p-A1GaN hole injection layers are numerically studied using the APSYS simulation software. The simulation results indicate that light-emitting diodes with p-A1GaN hole injection layers show superior optical and electrical performance, such as an increase in light output power, a reduction in current leakage and alleviation of efficiency droop. These improvements can be attributed to the p-A1GaN serving as hole injection layers, which can alleviate the band bending induced by the polarization field, thereby improving both the hole injection efficiency and the electron blocking efficiency.