The even and transparent nanometer TiO2 thin films named DegussaP25 as photocatalysis deposited on the surface of diffusers of solar light pipe were prepared by sol-gel processing.The rugged side of the diffusers of s...The even and transparent nanometer TiO2 thin films named DegussaP25 as photocatalysis deposited on the surface of diffusers of solar light pipe were prepared by sol-gel processing.The rugged side of the diffusers of solar light pipe was coated evenly with DegussaP25 solution for the quality of 1.75 g.The experiments had showed that when the coated side was away from the sun the lighting degree may be reduced compared with that facing the sun.The average reduction was only 3.03%,which would not have a significant impact on lighting.Diffusers are important parts of a light pipe which can diffuse light evenly to the place needed to be illuminated.The experiments showed that in a sunny summer day under the direct sunlight,the solar light pipe combined with photocatalysis could reduce the formaldehyde volume fraction in a box of 0.1 m3 from 1.0×10-6 to 0.16×10-6.After 1 h of photodegradation the formaldehyde volume changed from 1.0×10-6 down to 0.1×10-6 with faster and more complete degradation of formaldehyde.The rate of degradation under cloudy and partly cloudy conditions was slower than that under sunny conditions.It was slower in winter than in summer under sunny conditions.The experimental results also showed that the performance of photocatalysis combined with diffusers of light pipe had better effect in a small space.The performance in large space,such as open space,will be the next work in the future,which will be a great challenge.展开更多
The following article has been retracted due to the fact that it cannot be accepted as Duplicate Publication. The Editorial Board takes a very strong respect to the author’s situation on this matter. This paper publi...The following article has been retracted due to the fact that it cannot be accepted as Duplicate Publication. The Editorial Board takes a very strong respect to the author’s situation on this matter. This paper published in Journal of Power and Energy Engineering Vol.3 No.4, April 2015, has been removed from this site.展开更多
This work aims to improve the thermal performance of a light emitting diode(LED) module by employing a novelly assembled heat pipe heat sink. The heat pipe was embedded into the heat sink by a phase change expansion a...This work aims to improve the thermal performance of a light emitting diode(LED) module by employing a novelly assembled heat pipe heat sink. The heat pipe was embedded into the heat sink by a phase change expansion assembly(PCEA) process, which was developed by both finite element(FE) analysis and experiments. Heat transfer performance and optical performance of the LED modules were experimentally investigated and discussed. Compared to the LED module with a traditionally assembled heat pipe heat sink, the LED module employing the PCEA process exhibits about 20% decrease in the thermal resistance from the MCPCB to the heat pipe. The junction temperature is 4% lower and the luminous flux is 2% higher. The improvement in the thermal and optical performance is important to the high power LED applications.展开更多
基金supported by the National Natural Science Foundation of China (Grant No.50476036)
文摘The even and transparent nanometer TiO2 thin films named DegussaP25 as photocatalysis deposited on the surface of diffusers of solar light pipe were prepared by sol-gel processing.The rugged side of the diffusers of solar light pipe was coated evenly with DegussaP25 solution for the quality of 1.75 g.The experiments had showed that when the coated side was away from the sun the lighting degree may be reduced compared with that facing the sun.The average reduction was only 3.03%,which would not have a significant impact on lighting.Diffusers are important parts of a light pipe which can diffuse light evenly to the place needed to be illuminated.The experiments showed that in a sunny summer day under the direct sunlight,the solar light pipe combined with photocatalysis could reduce the formaldehyde volume fraction in a box of 0.1 m3 from 1.0×10-6 to 0.16×10-6.After 1 h of photodegradation the formaldehyde volume changed from 1.0×10-6 down to 0.1×10-6 with faster and more complete degradation of formaldehyde.The rate of degradation under cloudy and partly cloudy conditions was slower than that under sunny conditions.It was slower in winter than in summer under sunny conditions.The experimental results also showed that the performance of photocatalysis combined with diffusers of light pipe had better effect in a small space.The performance in large space,such as open space,will be the next work in the future,which will be a great challenge.
文摘The following article has been retracted due to the fact that it cannot be accepted as Duplicate Publication. The Editorial Board takes a very strong respect to the author’s situation on this matter. This paper published in Journal of Power and Energy Engineering Vol.3 No.4, April 2015, has been removed from this site.
基金Projects(51375177,U1401249,51405161)supported by the National Natural Science Foundation of ChinaProject(2014M560659)supported by the Postdoctoral Science Foundation of ChinaProject(2014B090901065)supported by the Science and Technology Planning Project for Industry-University-Research Cooperation in Guangdong Province,China
文摘This work aims to improve the thermal performance of a light emitting diode(LED) module by employing a novelly assembled heat pipe heat sink. The heat pipe was embedded into the heat sink by a phase change expansion assembly(PCEA) process, which was developed by both finite element(FE) analysis and experiments. Heat transfer performance and optical performance of the LED modules were experimentally investigated and discussed. Compared to the LED module with a traditionally assembled heat pipe heat sink, the LED module employing the PCEA process exhibits about 20% decrease in the thermal resistance from the MCPCB to the heat pipe. The junction temperature is 4% lower and the luminous flux is 2% higher. The improvement in the thermal and optical performance is important to the high power LED applications.
