Energy-Saving and Control of General Indoor Lighting Elements Fed from a Micro-Controlled Hybrid Power Generation System

In this study, an off grid wind-solar hybrid power generation system was established at Afyon Kocatepe University to meet the energy need of lighting system of three different laboratories. It is planned to efficiently use the energy obtained from the designed hybrid power generation system. For this purpose, PIC 16F877 was used in controlling of lighting load of laboratories. The off-grid wind-solar hybrid power generation system consists of 570 W 24 V mono crystal solar panels, 600 W wind power generation system and accumulator groups. The load control circuit made with PIC 16F877 is designed in a manner that will control the lighting armature groups individually activate and deactivate the armature groups according to intensity of illumination in environment. Besides, separately from generation and storing units constituting the hybrid power generation system, data in kWh are recorded by means of software in 10 seconds intervals. With the obtained power generation and storing data, analyzing of power consumption data when the load control system in active or passive position is made. According to analysis results, with controlling of lighting load and using of energy obtained from off grid wind-solar hybrid power generation system, 20.6% energy saving has been ensured.

Application Strategy of PLC Technology in Energy-Saving Control of Tunnel Lighting

In this study,we investigated on the application of planar lightwave circuit(PLC)technology in energy-saving control of tunnel lighting.The application status of PLC in the field of energy saving followed by the necessity of energy saving in tunnel lighting was analyzed.Finally,the application of PLC in tunnel lighting energy-saving control around the three dimensions of system overall architecture design,control scheme,and program control process was investigated.The results showed that the system meets the requirements of control effect,robustness,and visual effect after trial operation,and is suitable for practical applications.

Application Strategies of Automatic Addressable Single-Lamp Control Technology in Tunnel Lighting

The article mainly studies the application strategy of automatic addressable single-lamp control technology in tunnel lighting.It encompasses an introduction to this technology,an analysis of the tunnel lighting system using automatic addressable single-lamp control technology,and outlines the main development direction for this technology in modern tunnel lighting.The aim is to offer insights that can inform the rational deployment of this technology,thereby enhancing the lighting control effectiveness in modern tunnels and meeting their specific lighting requirements more effectively.

Parameters Optimization and Energy-Saving of Highway Tunnel Backlighting with LED

In order to acquire the most energy-saving luminairedistribution-parameters(LDPs)of highway tunnel interior zone backlighting,the parameters optimization model(POM)of backlighting for tunnel interior zone was established.Yanlieshan tunnel of Jiujing highway was taken as an example for the optimization.The optimal LDPs of the backlighting system of the tunnel interior zone were obtained by the POM,a comparison between the optimization results and those of Yanlieshan tunnel’s actual lighting system was performed,which showed that the optimized backlighting system with LED lamps installed according to the optimized LDPs could save energy remarkablely even under full capacity lighting condition.Illuminance and illuminance uniformity of the tunnel road surface still met the lighting demands even the LED lamp’s luminance decreased by 30%.A backlighting simulation experiment with the optimized backlighting LDPs for Yanlieshan tunnel was accomplished in the software Dialux.The simulation results basically agreed with the optimization calculated results from the POM which proved the correctness of the backlighting POM.

Application of Energy-Saving Materials in Architectural Design

The conventional process of building construction is associated with issues such as the waste of construction materials and environmental pollution.Sustainable development highlights the importance of energy conservation and eco-friendly practices.It is essential to use energy-efficient and green materials in building designs to ensure the healthy growth of construction companies.This article discusses the advantages and principles of incorporating energy-saving materials in architectural design.It examines the strategies and critical control points for using energy-saving materials in architectural design,offering guidance for the sustainable development of the construction industry.

Analysis of Current Research and Future Development Trends of Applying Solar Energy in Street Lighting

In the context of promoting green energy transition and addressing climate change globally,solar energy,as a clean and renewable energy source,has gradually become a hot topic for research.Solar streetlight systems realize energy self-sufficiency and environment-friendly lighting by integrating photovoltaic power generation technology and efficient LED lighting technology.By comprehensively analyzing the current status of the application of solar streetlights at home and abroad,this paper discusses its technical advantages,market penetration,and challenges in its development.In terms of technical characteristics,this paper focuses on analyzing the key technologies such as energy conversion efficiency and intelligent control systems of solar streetlights.

Controller Design of Intelligent Lighting Network

Studied are the controller design and basic principles of intelligent lighting network. TI’s MSP430F123 is used as a main controller. By using the ZigBee modules(Xbee/Xbee-PRO) and the GSM module(SIM300C) for wireless communications, the lighting control is enabled to access wireless network. This system uses a mobile phone to achieve light on-off directly, which can accomplish wireless control of intelligent lighting in families.

Smart Street Lighting Control and Monitoring System for Electrical Power Saving by Using VANET

The huge amount of electrical power of many countries is consumed in lighting the streets. However, vehicles pass with very low rate in specific periods of time and parts of the streets are not occupied by vehicles over time. In this paper, we propose a system that automatically switches off the light for the parts of the streets having no vehicles and turns on the light for these parts once there are some vehicles that are going to come. Logically, this system may save a large amount of the electrical power. In addition, it may increase the lifetime of the lamps and reduce the pollutions. This system automatically controls and monitors the light of the streets. It can light only the parts that have vehicles and help on the maintenance of the lighting equipments. Vehicular Ad-Hoc Networks (VANET) make it possible to propose such system. VANET enables the possibility to know the presence of vehicles, their locations, their directions and their speeds in real time. These quantities are what are needed to develop this system. An advantage of using VANET is that there is no need to use specific network and equipments to design the system, but VANET infrastructure will be used. This decreases the cost and speed up the deployment of such system. This paper focuses on the proposal of different possible architectures of this system. Results show that the saved energy may reach up to 65% and an increase of the lifetime of the lamps of 53%.

Automotive Lighting Systems Based on Luminance/Intensity Grids: A Proposal Based on Real-Time Monitoring and Control for Safer Driving

The requirements for automotive lighting systems,especially the light patterns ensuring driver perception,are based on criteria related to the headlamps,rather than the light perceived by drivers and road users.Consequently,important factors such as pavement reflectance,driver age,or time of night,are largely ignored.Other factors such as presence of other vehicles,vehicle speed and weather conditions are considered by the Adaptive Driving Beam(ADB)and Adaptive Front-lighting System(AFS)respectively,though with no information regarding the visual perception of drivers and other road users.Evidently,it is simpler to simulate and measure the light emitted by the lamps than the light reflected by the pavement or emitted by other vehicles.However the current technology in cameras and light sensors,communication protocols,and control of Light Emitting Diodes(LED),combined with decision-making techniques applied to large amounts of data,can open a new era in the operation of headlamps and thus ensure the visual needs of drivers in real time and under actual road conditions.The solution lies in an interaction road-sensor-headlamp,which is not based on the light emitted by headlamps,but rather on the light perceived by the drivers.This study thus proposes a dual grid based on luminance and luminous intensity,which would manage the headlamps by optimizing driver perception and the safety of all road users.

Controlled LED Lighting for Horticulture: A Review

As energy gradually becomes a more valuable commodity, the desire for reduced energy losses strengthens. Lighting is a critical field on this matter, as it accounts for a large percentage of the global electricity consumption and modern lighting systems are greatly more efficient than incandescent, discharge, and fluorescent lights. Previous research has proven that plants do not require the entire visible spectrum but react only to specific wavelengths, making it possible to control their growth and yield via artificial lighting. The flexibility of control of Light Emitting Diode (LED) lights allows for the combination of great energy losses reduction and controlled plant growth, achieving the improvement of two major parameters in a single action. This review paper summarizes the current research on the effect different light wavelengths have on specific plant species and discusses the applications of LED lighting for horticulture, yield storage, and disease protection.

Design of Diversified Intelligent Control System for Energy-saving Optimization of Solar Greenhouse in North China

Intelligent greenhouse can promote the development of modern agriculture, realize the high quality and high yield of crops, and also bring greater economic benefits. In accordance with the climate conditions in northwest China, a set of intelligent control system for diversified environment of solar greenhouse was designed. The system divides the annual greenhouse control into six stages according to the optimal energy saving. It uses modern detection technology to collect the greenhouse environmental temperature, environmental humidity, soil humidity, CO_(2) concentration and illumination parameters under different working modes. It uses programmable logic control technology to realize the data processing of various parameters and the action control of rolling film, wet curtain fan and other actuators. It uses KingView monitoring software to realize the monitoring and manual control of greenhouse environment parameters. The operation results indicate that the control system runs stably and basically meets the control requirements.

Human-inspired lighting control in robot systems with the intention of glare avoidance

This paper presents some human-inspired strategies for lighting control in a robot system for best scene interpretation,where the main intention is to avoid possible glares or highlights occurring in images. It firstly compares the characteristics of human eyes and robot eyes. Then some evaluation criteria are addressed to assess the lighting conditions. A bio-inspired method is adopted to avoid the visual glare which is caused by either direct illumination from large light sources or indirect illumination reflected by smooth surfaces. Appropriate methods are proposed to optimize the pose and optical parameters of the light source and the vision camera.

Homeostasis Lighting Control System Using a Sensor Agent Robot

In this study, “homeostasis”, the function by which living things keep their constancy, was emulated as a lighting control for a building space. The algorithm we developed mimics the mechanisms of the endocrine and immune systems. The endocrine system transmits information entirely, whereas the immune system transmits information with a concentration gradient. A lighting control system using the proposed algorithm was evaluated in a simulation and experiment using a sensor agent robot. In this algorithm, a robot recognizes a person’s behavior and uses it to decide his or her preference as to the illuminance. The results indicate that the algorithm can be used to realize a comfortable lighting control in several situations.

Automated Smart Utilization of Background Lights and Daylight for Green Building Efficient and Economic Indoor Lighting Intensity Control

The ways which are used today in order to light houses, offices, and most of the indoor areas are inefficient as a lot of energy is consumed unnecessarily during the day time. Mainly this problem because the interior lighting design consider the worst case when the light service is at night, which is not always valid. Also in most cases the lighting system design relies on people to control the lights switching on and off. This problem is also one of the design concerns in Green Building. In this paper, a solution to this problem and a method for people’s comfort who use the indoor facilities in industrial buildings is presented. In the proposed smart lighting system, lights switch on automatically when there is somebody in the room or in the occupied space and switch off when there is no occupancy. In addition to this known technique, adjustment of the brightness level of the lights will be possible via the personal computer or any other smart device. In this method, for the illumination level in the area, where is needed to be controlled for better energy saving, the light automatically is measured by the sensor and considering the amount of background lights coming from outside, automatically the brightness of lights is controlled to reach the preset level that determined for that room. By the means of this method, it is possible to provide better user comfort, avoid human forcedness to switch the light on and off, and hence effective energy saving. Arduino controller is used to build the controller and to demonstrate the results. Economic analysis was done to calculate the percentage of the energy saving that can be obtained by implementing the proposed smart lighting controller. As an outcome of the economic analysis, energy saving norm for an office with a standard size was calculated.

Design and Implementation on the Wind and Light Complementary LED Lighting Controller based on Novel Base Board Packaging Technology

In this paper, we conduct theoretical research on design and implementation on wind and light complementary LED lighting controller based on the novel base board packaging technology. LED, as a kind of device can convert electric power into visible light directly the homomorphism of semiconductor devices, with high efficiency and small energy consumption, good light quality, use safety, long service life, green environmental protection, flexible control as this is common lamps and lanterns is incomparable advantage. Therefore, it is considered to be 21 century of a new generation of lighting source. Based on the superiority of LED, it is widely applied in many fields of lighting. To enhance the traditional solar based pure LED system, we enhance it with the combination of the wind power and the optimized controller that holds specific meaning.

Automobile light control system based on CAN bus and contactless switch

In order to solve the complex wiring and low reliability of conventional light control system,an automobile contactless switch light system is designed combined with Hall element and controller area network （CAN） bus technology.The processing system of electromagnetic compatibility controlled by CAN bus is improved to reduce the electromagnetic interference from the controller and other sources of interference.With Freescale＇s high-performance single-chip MC9S08DZ60 and CAN transceiver TJA1050,the overall circuit design and software design are presented.The test results show that the designed light control system is feasible.

Seam Tracking and Visual Control for Robotic Arc Welding Based on Structured Light Stereovision

A real-time arc welding robot visual control system based on a local network with a multi-level hierarchy is developed in this paper. It consists of an intelligence and human-machine interface level, a motion planning level, a motion control level and a servo control level. The last three levels form a local real-time open robot controller, which realizes motion planning and motion control of a robot. A camera calibration method based on the relative movement of the end-effector connected to a robot is proposed and a method for tracking weld seam based on the structured light stereovision is provided. Combining the parameters of the cameras and laser plane, three groups of position values in Cartesian space are obtained for each feature point in a stripe projected on the weld seam. The accurate three-dimensional position of the edge points in the weld seam can be calculated from the obtained parameters with an information fusion algorithm. By calculating the weld seam parameter from position and image data, the movement parameters of the robot used for tracking can be determined. A swing welding experiment of type V groove weld is successfully conducted, the results of which show that the system has high resolution seam tracking in real-time, and works stably and efficiently.

Structured Light 3D Vision Based on Laser Scanning Space-encoding and Its Synchro Control

This paper presents the principle and mathematic model for the 3D depth map method based on space encoding images performed by modulating scanning structuredlight according to time sequences,and the synchro control among the camera,laser diode modulation and scanning polyhedron.

Multicenter randomised controlled trial comparing the high definition white light endoscopy and the bright narrow band imaging for colon polyps

AIM To compare high definition white light endoscopy and bright narrow band imaging for colon polyps' detection rates. METHODS Patients were randomised to high definition white light endoscopy(HD-WLE) or the bright narrow band imaging(b NBI) during withdrawal of the colonoscope. Polyps identified in either mode were characterised using b NBI with dual focus(b NBI-DF) according to the Sano's classification. The primary outcome was to compare adenoma detection rates(ADRs) between the two arms. The secondary outcome was to assess the negative predictive value(NPV) in differentiating adenomas from hyperplastic polyps for diminutive rectosigmoid lesions.RESULTS A total of 1006 patients were randomised to HD-WLE(n = 511) or b NBI(n = 495). The mean of adenoma per patient was 1.62 and 1.84, respectively. The ADRs in b NBI and HD-WLE group were 37.4% and 39.3%, respectively. When adjusted for withdrawal time(OR = 1.19, 95%CI: 1.15-1.24, P < 0.001), the use of b NBI was associated with a reduced ADR(OR = 0.69, 95%CI: 0.52-0.92). Nine hundred and thirty three polyps(86%) in both arms were predicted with high confidence. The sensitivity(Sn), specificity(Sp), positive predictive value and NPV in differentiating adenomatous from non-adenomatous polyps of all sizes were 95.9%, 87.2%, 94.0% and 91.1% respectively. The NPV in differentiating an adenoma from hyperplastic polyp using b NBI-DF for diminutive rectal polyps was 91.0%.CONCLUSION ADRs did not differ between b NBI and HD-WLE, however HD-WLE had higher ADR after adjustment of withdrawal time. b NBI surpassed the PIVI threshold for diminutive polyps.