In this paper we consider iteration of single-plateau functions,an important class of continuous functions with infinitely many forts,and investigate changes of number and length of plateaux under iteration.We use the...In this paper we consider iteration of single-plateau functions,an important class of continuous functions with infinitely many forts,and investigate changes of number and length of plateaux under iteration.We use the indices flatness,plateau limit and limit length to formulate those changes.Furthermore,we compute the flatness,plateau limit and limit length for all the nine types of single-plateau functions.展开更多
A method of ascertaining grade length limitation of freeways in mountain terrain is presented. The relationship models between 15 th percentile speeds and grades were built through the surveys and analyses of operatio...A method of ascertaining grade length limitation of freeways in mountain terrain is presented. The relationship models between 15 th percentile speeds and grades were built through the surveys and analyses of operation speeds on 7 typical sections of 3 freeways in mountain terrain. Using 15 thpercentile and 85 th percentile as speed limitations, the methods of determining admitted velocities were put forward according to the grades. Deceleration distances of longitudinal slopeways were analyzed utilizing the theories of vehicle. According to the results of analysis, grade length limitation was loosed. Finally the values of grade length limitation for freeways were put forward. The results could be used as references for freeway design.展开更多
A small cubic closed vessel with schlieren measurement technique combined with high-speed video camera were used to study limit flame properties under microgravity conditions at atmospheric pressure and room temperatu...A small cubic closed vessel with schlieren measurement technique combined with high-speed video camera were used to study limit flame properties under microgravity conditions at atmospheric pressure and room temperature.The rich flammability limit of C3H8/air was determined to be 9.2% C3H8.Stretched flame propagation speeds,stretched laminar burning velocities and unstretched laminar burning velocities near rich C3H8/air flammability limits were measured at different equivalence ratios.Outwardly propagating spherical flames were used to study the sensitivities of the flame propagation speeds and laminar burning velocities to flame stretch using Markstein lengths.Unstretched laminar burning velocity at rich flammability limit was determined to be 1.09cm/s.Lewis numbers were less than unity in rich C3H8/air and negative Markstein lengths were concluded.Absolute values of Markstein lengths were found to decrease linearly with equivalence ratios increase.展开更多
This article deals with two important issues in digital filter implementation: roundoff noise and limit cycles. A novel class of robust state-space realizations, called normal realizations, is derived and characteriz...This article deals with two important issues in digital filter implementation: roundoff noise and limit cycles. A novel class of robust state-space realizations, called normal realizations, is derived and characterized. It is seen that these realizations are free of limit cycles. Another interesting property of the normal realizations is that they yield a minimal error propagation gain. The optimal realization problem, defined as to find those normal realizations that minimize roundoff noise gain, is formulated and solved analytically. A design example is presented to demonstrate the behavior of the optimal normal realizations and to compare them with several well-known digital filter realizations in terms of minimizing the roundoff noise and the error propagation.展开更多
Arc-length-type and energy-type methods are two main strategies used in structural nonlinear tracing analysis, but the former is widely used due to the explicitness and clarity in conception, as well as the convenienc...Arc-length-type and energy-type methods are two main strategies used in structural nonlinear tracing analysis, but the former is widely used due to the explicitness and clarity in conception, as well as the convenience and reliability in calculation. It is very important to trace the complete load-deflection path in order to know comprehensively the characteristics of structures subjected to loads. Unfortunately, the nonlinear analysis techniques are only workable for tracing the limit-point-type equilibrium path. For the bifurcation-point-type path, most of them cannot secure a satisfactory result. In this paper, main arc-length-type methods are reviewed and compared, and the possible reasons of failures in tracing analysis are briefly discussed. Some improvements are proposed, a displacement perturbation method and a force perturbation method are presented for tracing the bifurcation-point-type paths. Finally, two examples are analyzed to verify the ideas, and some conclusions are drawn with respect to the arc-length-type methods.展开更多
In order to assess the effects of calibration data series length on the performance and optimal parameter values of a hydrological model in ungauged or data-limited catchments (data are non-continuous and fragmental ...In order to assess the effects of calibration data series length on the performance and optimal parameter values of a hydrological model in ungauged or data-limited catchments (data are non-continuous and fragmental in some catchments), we used non-continuous calibration periods for more independent streamflow data for SIMHYD (simple hydrology) model calibration. Nash-Sutcliffe efficiency and percentage water balance error were used as performance measures. The particle swarm optimization (PSO) method was used to calibrate the rainfall-runoff models. Different lengths of data series ranging from one year to ten years, randomly sampled, were used to study the impact of calibration data series length. Fifty-five relatively unimpaired catchments located all over Australia with daily precipitation, potential evapotranspiration, and streamflow data were tested to obtain more general conclusions. The results show that longer calibration data series do not necessarily result in better model performance. In general, eight years of data are sufficient to obtain steady estimates of model performance and parameters for the SIMHYD model. It is also shown that most humid catchments require fewer calibration data to obtain a good performance and stable parameter values. The model performs better in humid and semi-humid catchments than in arid catchments. Our results may have useful and interesting implications for the efficiency of using limited observation data for hydrological model calibration in different climates.展开更多
The current study performed a finite element analysis of the strain localization behavior of a voided ductile material using a non-local plasticity formulation in which the yield strength depends on both an equivalent...The current study performed a finite element analysis of the strain localization behavior of a voided ductile material using a non-local plasticity formulation in which the yield strength depends on both an equivalent plastic strain measurement (hardening parameter) and Laplacian equivalent. The introduction of gradient terms to the yield function was found to play an important role in simulating the strain localization behavior of the voided ductile material. The effect of the mesh size and characteristic length on the strain localization were also investigated. An FEM simulation based on the proposed non-local plasticity revealed that the load-strain curves of the voided ductile material subjected to plane strain tension converged to one curve, regardless of the mesh size. In addition, the results using non-local plasticity also exhibited that the dependence of the deformation behavior of the material on the mesh size was much less sensitive than that with classical local plasticity and could be succe展开更多
Pampus argenteus and Pampus chinensis form the high-value demersal Pomfret fishery of Bangladesh.But,due to a monotonic decline in catches over the last five years,it is essential to explore the current stock status c...Pampus argenteus and Pampus chinensis form the high-value demersal Pomfret fishery of Bangladesh.But,due to a monotonic decline in catches over the last five years,it is essential to explore the current stock status concerning the removal rate to ensure the sustainability of this fishery.Therefore,given the reliability and minimal data requirements,this study employed an extended Bayesian State-Space Surplus Production Model,JABBA(Just Another Bayesian Biomass Assessment),to assess the stock rigorously.The results revealed that the stock biomass of the Pomfret fishery in the final year of the time series is significantly lower than BMSY,the biomass required to produce MSY.Consequently,this study recommends a yearly catch limit(TAC)of 10,000 metric tons to prevent further depletion of the stock biomass.Furthermore,to avoid growth overfishing by allowing all immature fishes to reproduce at least once before being caught,this study also calculated the optimum length(Lopt)for catch for both species at which biologically maximum yield and revenue can be obtained.The estimated Lopt is 25 cm for P.argenteus and 30 cm for P.chinensis,and not to capture fishes with lengths lower than these limits,this study further calculated the minimum mesh size limits for gill and set bag nets is 7.5 cm.Though the mesh size regulation was estimated using length-based reference points derived from an empirical equation,this regulation can be used as an associate reference point when TAC is applied to assure the sustainability of this fishery.展开更多
基金supported by National Natural Science Foundation of China(Grant Nos.11501394,11771307 and 11726623)Science Research Fund of Sichuan Provincial Education Department(Grant No.15ZB0041)China Scholarship Council。
文摘In this paper we consider iteration of single-plateau functions,an important class of continuous functions with infinitely many forts,and investigate changes of number and length of plateaux under iteration.We use the indices flatness,plateau limit and limit length to formulate those changes.Furthermore,we compute the flatness,plateau limit and limit length for all the nine types of single-plateau functions.
基金Sponsored by the Specialized Research Fund for the Doctoral Program of High Education(Grant No.20030213030)
文摘A method of ascertaining grade length limitation of freeways in mountain terrain is presented. The relationship models between 15 th percentile speeds and grades were built through the surveys and analyses of operation speeds on 7 typical sections of 3 freeways in mountain terrain. Using 15 thpercentile and 85 th percentile as speed limitations, the methods of determining admitted velocities were put forward according to the grades. Deceleration distances of longitudinal slopeways were analyzed utilizing the theories of vehicle. According to the results of analysis, grade length limitation was loosed. Finally the values of grade length limitation for freeways were put forward. The results could be used as references for freeway design.
基金Supported by the Research Foundation of Beijing Institute of Technology(20070242004)
文摘A small cubic closed vessel with schlieren measurement technique combined with high-speed video camera were used to study limit flame properties under microgravity conditions at atmospheric pressure and room temperature.The rich flammability limit of C3H8/air was determined to be 9.2% C3H8.Stretched flame propagation speeds,stretched laminar burning velocities and unstretched laminar burning velocities near rich C3H8/air flammability limits were measured at different equivalence ratios.Outwardly propagating spherical flames were used to study the sensitivities of the flame propagation speeds and laminar burning velocities to flame stretch using Markstein lengths.Unstretched laminar burning velocity at rich flammability limit was determined to be 1.09cm/s.Lewis numbers were less than unity in rich C3H8/air and negative Markstein lengths were concluded.Absolute values of Markstein lengths were found to decrease linearly with equivalence ratios increase.
基金the National Nature Science Foundation of China (60774021)
文摘This article deals with two important issues in digital filter implementation: roundoff noise and limit cycles. A novel class of robust state-space realizations, called normal realizations, is derived and characterized. It is seen that these realizations are free of limit cycles. Another interesting property of the normal realizations is that they yield a minimal error propagation gain. The optimal realization problem, defined as to find those normal realizations that minimize roundoff noise gain, is formulated and solved analytically. A design example is presented to demonstrate the behavior of the optimal normal realizations and to compare them with several well-known digital filter realizations in terms of minimizing the roundoff noise and the error propagation.
基金The project supported by the Special Research Fund for Doctor Program of Universities (9424702)
文摘Arc-length-type and energy-type methods are two main strategies used in structural nonlinear tracing analysis, but the former is widely used due to the explicitness and clarity in conception, as well as the convenience and reliability in calculation. It is very important to trace the complete load-deflection path in order to know comprehensively the characteristics of structures subjected to loads. Unfortunately, the nonlinear analysis techniques are only workable for tracing the limit-point-type equilibrium path. For the bifurcation-point-type path, most of them cannot secure a satisfactory result. In this paper, main arc-length-type methods are reviewed and compared, and the possible reasons of failures in tracing analysis are briefly discussed. Some improvements are proposed, a displacement perturbation method and a force perturbation method are presented for tracing the bifurcation-point-type paths. Finally, two examples are analyzed to verify the ideas, and some conclusions are drawn with respect to the arc-length-type methods.
基金supported by the National Basic Research Program of China (the 973 Program,Grant No.2010CB951102)the National Supporting Plan Program of China (Grants No.2007BAB28B01 and 2008BAB42B03)the National Natural Science Foundation of China (Grant No. 50709042),and the Regional Water Theme in the Water for a Healthy Country Flagship
文摘In order to assess the effects of calibration data series length on the performance and optimal parameter values of a hydrological model in ungauged or data-limited catchments (data are non-continuous and fragmental in some catchments), we used non-continuous calibration periods for more independent streamflow data for SIMHYD (simple hydrology) model calibration. Nash-Sutcliffe efficiency and percentage water balance error were used as performance measures. The particle swarm optimization (PSO) method was used to calibrate the rainfall-runoff models. Different lengths of data series ranging from one year to ten years, randomly sampled, were used to study the impact of calibration data series length. Fifty-five relatively unimpaired catchments located all over Australia with daily precipitation, potential evapotranspiration, and streamflow data were tested to obtain more general conclusions. The results show that longer calibration data series do not necessarily result in better model performance. In general, eight years of data are sufficient to obtain steady estimates of model performance and parameters for the SIMHYD model. It is also shown that most humid catchments require fewer calibration data to obtain a good performance and stable parameter values. The model performs better in humid and semi-humid catchments than in arid catchments. Our results may have useful and interesting implications for the efficiency of using limited observation data for hydrological model calibration in different climates.
文摘The current study performed a finite element analysis of the strain localization behavior of a voided ductile material using a non-local plasticity formulation in which the yield strength depends on both an equivalent plastic strain measurement (hardening parameter) and Laplacian equivalent. The introduction of gradient terms to the yield function was found to play an important role in simulating the strain localization behavior of the voided ductile material. The effect of the mesh size and characteristic length on the strain localization were also investigated. An FEM simulation based on the proposed non-local plasticity revealed that the load-strain curves of the voided ductile material subjected to plane strain tension converged to one curve, regardless of the mesh size. In addition, the results using non-local plasticity also exhibited that the dependence of the deformation behavior of the material on the mesh size was much less sensitive than that with classical local plasticity and could be succe
文摘Pampus argenteus and Pampus chinensis form the high-value demersal Pomfret fishery of Bangladesh.But,due to a monotonic decline in catches over the last five years,it is essential to explore the current stock status concerning the removal rate to ensure the sustainability of this fishery.Therefore,given the reliability and minimal data requirements,this study employed an extended Bayesian State-Space Surplus Production Model,JABBA(Just Another Bayesian Biomass Assessment),to assess the stock rigorously.The results revealed that the stock biomass of the Pomfret fishery in the final year of the time series is significantly lower than BMSY,the biomass required to produce MSY.Consequently,this study recommends a yearly catch limit(TAC)of 10,000 metric tons to prevent further depletion of the stock biomass.Furthermore,to avoid growth overfishing by allowing all immature fishes to reproduce at least once before being caught,this study also calculated the optimum length(Lopt)for catch for both species at which biologically maximum yield and revenue can be obtained.The estimated Lopt is 25 cm for P.argenteus and 30 cm for P.chinensis,and not to capture fishes with lengths lower than these limits,this study further calculated the minimum mesh size limits for gill and set bag nets is 7.5 cm.Though the mesh size regulation was estimated using length-based reference points derived from an empirical equation,this regulation can be used as an associate reference point when TAC is applied to assure the sustainability of this fishery.