CHARACTERISTICS ANALYSIS OF THE INDUCED OVERCURRENT GENERATED BY CLOSE TRIGGERED LIGHTNING ON THE OVERHEAD TRANSMISSION POWER LINE

Techniques of artificially-triggered lightning have provided a significantly useful means to directly measure various physical parameters of lightning discharge and to conduct research on protection methods of lightning electromagnetic pulses.In this study,using capacitive and resistive dividers,current probes and optical fiber transmission devices,we measured and analyzed the induced overvoltage on the overhead transmission line and the overcurrent through Surge Protective Devices(SPD) when a lightning discharge was artificially triggered nearby on August 12,2008 at Conghua Field Lightning Experiment Site.The triggered lightning discharge contained an initial current stage and eight return strokes whose peak currents ranged from 6.6kA to 26.4kA.We found that overcurrents through SPD were induced on the power line both during the initial continuous current stage and the return stroke processes.During the return strokes,the residual voltage and the current through the SPD lasted up to the ms(millisecond) range,and the overcurrents exhibited a mean waveform up to 22/69μs with a peak value of less than 2kA.Based on the observed data,simple calculations show that the corresponding single discharge energy was much greater than the values of the high voltage pulse generators commonly used in the experiments regulated for SPD.The SPD discharge current peak was not synchronous to that of the residual voltage with the former obviously lagging behind the latter.The SPD discharge current peak was well correlated with the triggered lightning current peak and the wave-front current gradient.The long duration of the SPD current is one of the major reasons why the SPD was damaged even with a big nominal discharge current.

Usage and Benefit of an Overhead Line Monitoring System

Overhead lines are the backbone of the electrical power transmission.Contrary to the distributions networks,the transmission system consists only in exceptional cases of longer cable lines.Typical exceptions are connections of cavern power plants,approaches to airports or bird sanctuaries and lines in urban centres.In the majority of cases,an overhead line is the most economic and practicable solution for the energy transmission.In tourism regions,an overhead line will be seen as impairment of nature or landscape and so the approval chain and procedure is in most countries long-winded and circumstantial.At the other hand,the energy consumption in Europe is growing and the volatility of transmitted power is also increasing during the last decade caused by the opening of the electric energy market.This opening process leads to a stopping of the enlargement of the interoperation network and to a minimisation of the maintenance of existing lines.Today the network operates more often at the limit of the equipment and the small and large-areas disturbances and blackouts are increasing.The operators of transmission lines are forced to ensure the electrical power supply and so they have to improve the reliability of the network.One solution is to monitor the critical(heavy loaded)overhead lines.For example,with the knowledge of the thermal condition,the risk of unexpected outages can be reduced.Today several monitoring systems are available on the market.They differ in the principle and techniques of the condition evaluation.The three most interesting output variables are the line temperature,the capable transmission power and the actual sag of the investigated section.In this paper an overview of existing overhead line monitoring system and also an outline over the usage and benefit for the application will be given.Thermal monitoring is one technique to improve the reliability of the network and for increasing or optimising the capable transmission power.

Research on Lightning Protection of Overhead Power Distribution Lines

There are two major protective methods against lightning outages on overhead distribution lines.One is a surge arrester,and the other is an overhead ground wire.The surge arresters have rather constant effect regardless of the cause of the lightning outage.On the other hand,the effect of an overhead ground wire is quite different in two major causes,the direct lightning hit and the induced overvoltage.It is sufficient to provide surge arresters with an interval of 300 m for protection against the induced overvoltage caused by the nearby lightning stroke.Use of an overhead ground wire together with surge arresters is effective for lightning protection against the direct lightning hit to a distribution line.Puncture of surge arresters is the popular outage when the outage caused by the insulation break decreases sufficiently.Also,the existence of nearby trees leads to the line break due to the side flash from a tree.Advanced lightning protection equipment with ZnO arrester components is popular in Japan.Modeling of a pole transformer and application of an electromagnetic analysis method,such as FDTD method,to surge phenomena is considerably advanced.

The Study of Overhead Line Fault Probability Model Based on Fuzzy Theory

In the background of the design and construction of Smart Grid Operation Supporting System for District Power Networks, this paper established the weighted fault probability model of the overhead line which is based on equipment operating status, utility theory and fuzzy theory. In this model, the proper membership function is adopted to describe the influence of lightning, wind speed, line ice and temperature, and the outage rate of overhead line, derived from historical statistics, is amended. Based on this model, the power supply risk analysis software is developed to calculate the online risk indicators of district grid, and provide real-time decision support information based on risk theory for scheduling operations personnel.

Three-dimensional Model Analysis of Electric Field Excited by Multi-circuit Intersecting Overhead Transmission Lines

This work is carried out to predict the special distribution of electric field induced by multi-circuit intersecting overhead high-voltage (HV) transmission lines (TLs) within a large range without any expensive and time-consuming computation. The two main parts of the presented methodology are 1) setting up a three-dimensional (3D) model to calculate the electric field based on combining ca- tenary equations with charge simulation method and 2) calculating the hybrid electric field excited by multi-circuit intersecting TLs using coordinate transformation and superposition technique. Examples of different TLs configurations, including a 220 kV single-circuit hori- zontally configured TLs, a 500 kV single-circuit triangularly configured TLs and a combination of the 220 kV TLs and the 550 kV TLs, are illustrated to verify the validity of this methodology. A more complicatal configurations, including a 500 kV double-circuit TLs and two 220 kV single-circuit horizontally configured TLs, are also calculated. Conclusions were drawn from the simulation: 1) The presented 3D model outperforms 2D models in describing the electric field distribution generated by practical HV TLs with sag and span. 2) Coordinate trans- formation and superposition technique considerably simplify the electric field computation for multi-circuit TLs configurations, which makes it possible to deal with complex engineering problems. 3) The electric field in the area covered by multiple intersecting overhead TLs is distorted and the hybrid electric field strength in some partial region increases so sharply that it might exceed the admissible value. 4) The configuration parameters of the TLs and the spatial configuration of multi-circuit TLs, for instance, the height of TLs, the length of span and the intersection angle of multiple circuits, influence the strength and the distribution of hybrid electric field. The influence regularities sum- marized in this paper can be referred by future TL designs to meet the electromagnetic environmental protection regulations.

Aspects of High Voltage Cable Sections in Modern Overhead Line Transmission Systems

Electrical power transmission is dominated by overhead line systems at present.This is mainly based on more than hundred years of experience of utilities in running overhead lines.Furthermore,overhead lines have proven their operational reliability and functional assurance.In the past,cables were used in distribution networks in urban areas for the most part with the exception of direct current submarine cables.New developments of high voltage XLPE cables make it possible to use this technology for EHV level applications in transmission networks.Within this paper,mixed network configurations,consisting of overhead lines and high voltage cables,are investigated.An exemplary EHV transmission line with a total length of about 100 km,which is quite typical for Central Europe,has been studied.Several different line combinations are discussed with varied rates between overhead line sections and cable sections length in practice.The length of the cable sections are ranging from several kilometers up to lengths of 100 km.In this paper the work focuses on the transient behavior of combined 400 kV overhead and cable lines during switching processes and lightning impacts.A number of calculations were carried out to get an overview of the transient stress in numerous network nodes along the transmission system.Numerical programs like ATP/EMTP have been used for these simulations.Peak values and wave shapes of the transient voltage stress have been evaluated,based on different systems and within possible combinations.In respect of the insulation coordination and transient stress at network nodes,the voltage-time trends are also analyzed.The combination of high voltage overhead and cable transmission systems,especially such with lengths of more than about 50 km,are making tightened and extended demands to the network design,to the operational management and of course to the network protection also.As an output of this investigations,the results might influence the strategy in running this new type of combined transmission systems.

Design of 1000-kV AC Single-Circuit Overhead Transmission Line

The UHVAC 1 000-kV transmission system is so far the one with the most advanced transmission technique applied and highest operation voltage.There are no guidelines or standards available for the design of 1 000-kV overhead transmission line in China.Study on key technologies and design schemes shall be carried out to ascertain the technical principles and construction standards for project construction,which are presented in this paper based on the Southeast Shanxi-Nanyang-Jingmen test and demonstration transmission line.A comparison and analysis of technical data and economic indices between UHV line and other lines are also described.

Mechanics Analysis of Overhead Transmission Lines Based On-line Monitoring

At present, the on-line monitoring is widely applied to the power line monitoring. In this paper, a new mechanical calculation model is established according to the on-line monitoring. And this model is based on the parameters that tension sensors and angle sensors on suspended points detect, and combines with the parameters of the wire itself, and also considers the deflection angel of wires due to wind. In this model, mechanics parameters of wires are turned into the new coordinate plane after deflection angel of wires due to wind, or windage yaw plane. A statics tension balance equation is built in the vertical direction of the new windage yaw plane. According to the theoretical analysis and algorithm, we verify the accuracy of this newly developed mechanical calculation model.

火箭引雷至架空线路与地面电流对比分析

2018—2019年夏季在广州从化开展了火箭引雷试验,雷击对象分为两种,分别是架空线路和地面。对比了两种引雷情况下各阶段雷电流的电流波形参数的差异,发现引雷至地面情况下初始阶段的最大电流、平均电流、转移电荷、作用积分分别是引雷至架空线路情况下的2.8、2.4、2.0、5.3倍。引雷至地面情况下回击的上升时间几何均值为0.25μs,小于引雷至线路情况下的0.60μs,而对于电流峰值等其他回击波形参数而言,差异不明显。M分量与初始连续电流脉冲类似,引雷至线路情况下的电流峰值、转移电荷、连续电流水平均小于引雷至地面情况下的。基于诺顿电流源等效电路模型分析两种引雷情况下雷电流不同阶段存在差异的原因,可能是雷电在不同电流阶段时其通道等效阻抗不一样所导致的。

基于网侧资源协调的自储能柔性互联配电系统日前-日内优化

为优化储能型智能软开关(E-SOP)、传统网侧调控设备的运行策略,提升高渗透率光伏配电网运行水平,提出了基于网侧资源协调的自储能柔性互联配电系统日前-日内优化模型。首先,提出了“源网荷储”下多种网侧资源协调利用的多时间尺度优化控制架构;其次,在日前阶段构建计及有载调压变压器、无功补偿装置、联络开关、E-SOP和柔性负荷的长时间有功-无功联合优化模型,在日内阶段建立多目标滚动优化模型,并采用线性化方法将模型转换为混合整数线性规划模型;然后,基于KL散度构建源荷不确定性模糊集,给出日前两阶段分布鲁棒优化模型转化过程和基于列与约束生成算法的求解方法;最后,算例仿真验证所提方法的有效性。

基于角度传感器的弓网相对坐标检测技术研究

在电气化公路弓网相对坐标的检测中,基于机器视觉的非接触式检测技术的检测精度受图像采集环境的影响较大,基于光电传感器的接触式检测技术的检测精度受传感器安装密度限制。提出了一种基于角度传感器的接触式相对坐标检测技术,用于电气化公路的弓网相对坐标检测。首先,基于双接触线的电气化公路接触网,搭建弓网相对坐标检测实验台,建立弓网相对坐标与角度信息关联函数;然后,研究系统刚度、角度传感器线性度对实验台检测误差的影响规律,建立多项式修正函数对关联函数进行修正;最后,基于修正的弓网相对坐标关联函数,进行弓网相对坐标检测实验,得到实验台检测的绝对误差为±1 mm,相对误差为±0.5%,具备较高的检测精度。

内陆清洁能源基地±800kV/10000MW直流外送拓扑设计

大力开发大规模清洁能源基地是国家“十四五”现代能源体系规划明确的重点任务。针对藏东南地区大规模水电、光伏送出场景,计及新能源基地海拔高、输电走廊受限问题,设计了±800 kV/10000 MW多直流电压等级混合直流、多直流电压等级柔直和四端混合直流系统送出拓扑。针对沙戈荒地区风电、光伏送出场景,设计了±800 kV/10000 MW三端柔直、四端柔直和多直流电压等级混合直流系统送出拓扑。最后,在PSCAD/EMTDC仿真平台搭建了各拓扑方案的仿真模型,对比分析了各拓扑的技术特点。通过研究,以期为未来相关工程实践拓扑设计提供参考。

基于GS-SVR的架空输电线路工程投资估算预测研究

传统的投资估算编制模式存在过度依赖定额的现象,随着大量工程造价数据的积累,利用其实现投资估算,以弥补传统定额计价模式的不足,能够对建设项目工程造价起到总体控制作用。文章以架空输电线路工程为例,基于支持向量回归机(Support Vector Regression,SVR)研究架空输电线路工程投资估算问题。结果表明:通过选取影响架空输电线路工程投资估算的主要指标,构建基于SVR的架空输电线路工程投资估算模型,并利用改进的网格搜索法(Grid Search,GS)优化模型参数,得到基于GS-SVR的投资估算预测模型;与传统的线性回归和SVR模型相比,GS-SVR模型表现出更为良好的性能。

基于电磁时间反演的VSC-HVDC系统架空线-电缆混合线路故障定位方法

针对传统故障定位方法无法应用于架空线-电缆混合直流线路的问题,提出了一种架空线-电缆混合直流线路的故障定位方法,该方法采用先确定故障点所在区段、后在区段中定位的原理。利用故障附加网络的直流分量定义了故障区段判别函数,通过该判别函数在不同区段发生故障时数值不同实现故障区段的判定。然后,分析了电磁时间反演理论在故障定位中的可行性,分析确定了故障特征谐波。利用线路两端特征谐波的电流行进波作为时间反演电路的电流源,设置与原线路拓扑结构镜像的线路,利用时间反演电流源与镜像线路构建时间反演电路。在此基础上,根据时间反演的能量聚焦特性列写故障区段内的故障定位方程并实现区段内故障定位。利用PSCAD/EMTDC搭建的电压源型换流器高压直流输电(VSC-HVDC)系统仿真证明了所提方法能实现线缆混合直流输电线路的故障定位。

基于激光点云技术的架空输电线路目标建模方法研究

文章研究基于架空输电线路三维激光点云数据,通过点云自动分类(杆塔、导地线、地面、植被等)实现不同地物提取,在此基础上建立不同塔型模型库并进行特征分析,实现杆塔和导地线的类别提取,并进行精准空间坐标(X、Y、H)提取,实现架空输电线路重要巡检对象的精准定位信息获取,并以此规划基于输电线路三维点云数据的架空输电线路全自动巡检航迹规划,为输电线路去人机全自动巡检技术的研究提供技术支撑。

考虑暂态过电压特性的架空输电线路雷击故障时空预警方法

针对运行环境复杂多变,故障率持续居高不下,雷击故障占比较大,并具有随机性与无法预知性的问题,提出考虑暂态过电压特性的架空输电线路雷击故障时空预警方法。深入解析雷击机理与雷电流,确定雷击(感应雷与直击雷)输电线路暂态过电压计算方式,通过小波多分辨率分解算法处理输电线路暂态信号,评估暂态过电压在信号频段中的能量比,识别累计故障,判断雷击点与故障点是否一致,利用单端检测确定雷击点的位置,完成架空输电线路雷击故障的时空预警。实验数据显示,在不同实验组别背景下,当阈值pΔ取值为9.3时,雷击故障识别精度达到最大值92%,雷击点定位精度高达80%。可以获得精准的雷击故障识别结果与雷击点定位结果,充分证实了提出方法具备较好的雷击故障时空预警效果。