Application of Piezoelectric Materials in a Novel Linear Ultrasonic Motor based on Shear-induced Vibration Mode

A novel linear ultrasonic motor based on d15 effect of piezoelectric materials was presented. The design idea aimed at the direct utilization of the shear-induced vibration modes of piezoelectric material. Firstly, the inherent electromechanical coupling mechanism of piezoelectric material was investigated, and shear vibration modes of a piezoelectric shear block was specially designed. A driving point’s elliptical trajectory induced by shear vibration modes was discussed. Then a dynamic model for the piezoelectric shear stator was established with finite element（FE） method to conduct the parametric optimal design. Finally, a prototype based on d15 converse piezoelectric effect is manufactured, and the modal experiment of piezoelectric stator was conducted with laser doppler vibrometer. The experimental results show that the calculated shear-induced vibration modes can be excited completely, and the new linear ultrasonic motor reaches a speed 118 mm/s at noload, and maximal thrust 12.8 N.

A virtual experiment showing single particle motion on a linearly vibrating screen-deck

A virtual sieving experimental simulation system was built using physical simulation principles.The effects of vibration frequency and amplitude,the inclination angle of the screen-deck and the vibration direction angle of screen on single particle kinematics were predicted.Properties such as the average velocity and the average throw height were studied.The results show that the amplitude and the angle of vibration have a great effect on particle average velocity and average height.The vibration frequency and the screen-deck inclination angle appear to have little influence on these responses.For materials that are difficult to screen the vibration frequency and amplitude,the screen-deck inclination angle and the vibration angle should be set to 14 Hz,6.6 mm,6° and 40°,respectively,to obtain optimal particle kinematics.A screening process can be simulated reliably by means of a virtual experiment and these results provide references for both screening theory research and sieving practice.

Vibrations of revolution shells in turning-point range and applications in loudspeakers

An overview of the research conducted in the area of linear and nonlinear vibrations of loudspeakers and revolution shells was given in the turning-point frequency range in Chapter 1. It shows that some problems concerning vibrations of shells in the turning-point range have to be further studied. The linear vibrations of truncated revolution shells with the first-order turningpoint were systematically investigated in the turningpoint range from Chapter 2 to Chapter 6, including the general solutions for the free vibration, the eigenvalues under various boundary conditions, the forced vibrations driven by an edge force or an edge displacement and some related special effects, and the applications in loudspeaker vibrations. The nonlinear autoparametric vibration was examined in Chapter 7. Main results are listed as follows.

Integral precession calibration method of PIGA on linear vibration table

Linear vibration table can provide harmonic accelerations to excite the nonlinear error terms of Pendulous Integrating Gyro Accelerometer(PIGA).Integral precession calibration method is proposed to calibrate PIGA on a linear vibration table in this paper.Based on the precise expressions of PIGA’s inputs,the error calibration model of PIGA is established.Precession angular velocity errors of PIGA are suppressed by integer periodic precession and the errors caused by non-integer periods vibrating are compensated.The complete calibration process,including planning,preparation,PIGA testing,and coefficient identification,is designed to optimize the test operations and evaluate the calibration results.The effect of the main errors on calibration uncertainty is analyzed and the relative sensitivity function is proposed to further optimize the test positions.Experimental and simulation results verify that the proposed 10-position calibration method can improve calibration uncertainties after compensating for the related errors.The order of calibration uncertainties of the second-and third-order coefficients are decreased to 10^(-8)(rad.s^(-1))/g^(2)and 10^(-8)(rad.s^(-1))/g3,respectively.Compared with the other two classical calibration methods,the calibration uncertainties of PIGA’s nonlinear error coefficients can be effectively reduced and the proportional residual errors are decreased less than 3×10-6(rad.s^(-1))/g by using the proposed calibration method.

THICKNESS-SHEAR AND THICKNESS-TWIST VIBRATIONS OF CIRCULAR AT-CUT QUARTZ RESONATORS

Exact solutions for free vibration frequencies and modes are obtained for thickness- shear and thickness-twist vibrations of unelectroded circular AT-cut quartz plates governed by the two-dimensional scalar differential equation derived by Tiersten and Smythe. Comparisons are made with experimental results and the widely-used perturbation solution by Tiersten and Smythe under the assumption of weak in-plane anisotropy. Our solution is found to be much closer to the experimental results than the perturbation solution. For the frequency of the fundamental thickness-shear mode, the error of the perturbation method is 0.4549%, significant in resonator applications.

Collaborative optimization of linear vibrating screen screening efficiency and dynamic response stability based on coupled DEM-MBK simulation

The dynamic response stability of the vibrating screen is an important factor affecting the screening effect and the structural performance of the vibrating screen.In this paper,to improve dynamic response stability and screening efficiency,we optimized the configuration of linear screening process parameters based on the co-optimization method with dual objectives via the virtual experiment.Firstly,a coupled DEM-MBK simulation model was established according to the dynamics of linear screen,and the dy-namic response law of the screen machine under material impact was investigated.Secondly,the quantitative index of dynamic response stability according to the time-domain characteristics of the centroid amplitude was established.The trend and significance of three types of screening process pa-rameters,including excitation,damping and structure,on the screening efficiency and dynamic response stability were analyzed through virtual orthogonal experiments.Finally,a parameter configuration scheme to achieve co-optimization was proposed based on the comprehensive balance method.The virtual experiment results show that the screening efficiency and dynamic response stability of the proposed scheme are improved by 3.28%and 49.07%,respectively,compared with the empirical parameter configuration.Obviously,the co-optimization method can maintain high screening efficiency and dynamic response stability at the same time,which is beneficial to improve the service life of the screen surface and screen body.

Some Modal Relations and Generalized Velocity Method in State Space

Real mode theory in configuration space has shown that the mode acceleration method converges faster than the mode displacement method. This paper demonstrates a similar conclusion in the state space. Some new expressions on modal parameter matrices were set up first. A generalized velocity method (GVM) is then demonstrated in a systematic way. This method is the so\|called complex mode velocity method, but the expressions and schemes are given in terms of parametric matrices in configuration space. Theoretical comparison of this GVM with the traditional complex mode method shows some interesting conclusions. The latter approach is actually a generalized displacement method (GDM). Without mode reduction, the displacement responses of the concerned system resulting from both approaches are identical. On the other hand, both approaches have to adopt mode reduction to become practical. Under this situation, GVM has advantages because it compensates for the contribution of the omitted high\|order modes to the displacement responses.