We present a stable linear-cavity single longitudinal mode (SLM) erbium-doped silica fiber laser. It consists of four fiber Bragg gratings (FBGs) directly written in a section of photosensitive erbium-doped fiber ...We present a stable linear-cavity single longitudinal mode (SLM) erbium-doped silica fiber laser. It consists of four fiber Bragg gratings (FBGs) directly written in a section of photosensitive erbium-doped fiber (EDF) to form an asymmetric three-cavity structure. The stable SLM operation at a wavelength of 1545.112 nm with a 3-dB bandwidth of 0.012 nm and an optical signal-to-noise ratio (OSNR) of about 60 dB is verified experimentally. Under laboratory conditions, the performance of a power fluctuation of less than 0.05 dB observed from the power meter for 6 h and a wavelength variation of less than 0.01 nm obtained from the optical spectrum analyzer (OSA) for about 1.5 h are demonstrated. The gain fiber length is no longer limited to only several centimeters for SLM operation because of the excellent mode-selecting ability of the asymmetric three-cavity structure. The proposed scheme provides a simple and cost-effective approach to realizing a stable SLM fiber laser.展开更多
Diffusion tensor imaging is a unique method to visualize white matter fibers three-dimensionally, non-invasively and in vivo, and therefore it is an important tool for observing and researching neural regeneration. Di...Diffusion tensor imaging is a unique method to visualize white matter fibers three-dimensionally, non-invasively and in vivo, and therefore it is an important tool for observing and researching neural regeneration. Different diffusion tensor imaging-based fiber tracking methods have been already investigated, but making the computing faster, fiber tracking longer and smoother and the details shown clearer are needed to be improved for clinical applications. This study proposed a new fiber tracking strategy based on tri-linear interpolation. We selected a patient with acute infarction of the right basal ganglia and designed experiments based on either the tri-linear interpolation algorithm or tensorline algorithm. Fiber tracking in the same regions of interest (genu of the corpus callosum) was performed separately. The validity of the tri-linear interpolation algorithm was verified by quan- titative analysis, and its feasibility in clinical diagnosis was confirmed by the contrast between tracking results and the disease condition of the patient as well as the actual brain anatomy. Statis- tical results showed that the maximum length and average length of the white matter fibers tracked by the tri-linear interpolation algorithm were significantly longer. The tracking images of the fibers indicated that this method can obtain smoother tracked fibers, more obvious orientation and clearer details. Tracking fiber abnormalities are in good agreement with the actual condition of patients, and tracking displayed fibers that passed though the corpus callosum, which was consistent with the anatomical structures of the brain. Therefore, the tri-linear interpolation algorithm can achieve a clear, anatomically correct and reliable tracking result.展开更多
We present a numerical investigation of the propagation and the switching of ultra-short pulses (100 fs) in a two-core nonlinear coupler of photonic crystal fibers constructed with periodically modulated the non-linea...We present a numerical investigation of the propagation and the switching of ultra-short pulses (100 fs) in a two-core nonlinear coupler of photonic crystal fibers constructed with periodically modulated the non-linearity fiber (PMNL-PFC). Our simulations are taking into account different amplitude and frequency modulations of the PMNL-PFC. A coupler for coupling whose length is Lc = 1.8 cm, the transmission characteristics, the compression factor, the crosstalk (Xtalk) and extinction ratio (Xratio) levels of the first order solitons were studied for low to high pump energies considering 2Lc. By an analysis on the reference channel (channel 2), it is observed that at low modulation frequencies an increase occurs in the switching power increasing transmission efficiency. For high modulation frequencies, the transmitted energy efficiency loses. The switching pulses are stronger for low frequency and high amplitude modulation. The Xtalk is a function of the measurement made on the secondary channel (channel 1). It was observed that this unwanted high-frequency energy increases to lessen the measure of the amplitude modulation. In summary, we have demonstrated that introduction of a non-linearity profile takes the periodically modulated PMNL-PFC to strong variations at transmission efficiency, Xtalk, Xratio a function of frequency and modulation amplitude and the input power.展开更多
In this work fibers derived from coffee</span><span style="font-family:Verdana;">,</span><span style="font-family:Verdana;"> hulls ha</span><span style="font-f...In this work fibers derived from coffee</span><span style="font-family:Verdana;">,</span><span style="font-family:Verdana;"> hulls ha</span><span style="font-family:Verdana;">ve</span><span style="font-family:Verdana;"> been incorporated into Linear Low Density Polyethylene (LLDPE). The influence of the filler content on </span><span style="font-family:Verdana;">the </span><span style="font-family:Verdana;">thermal and physicomechanical properties of the composites obtained was assessed. The results showed that the incorporation of fibers was able to improve the thermostability of LLDPE/Coffee hulls fibers;comparing the treated fiber composite with untreated fiber composites, the chemical treatment reduces by 58.3% the water absorption, while increasing the elongation and tensile strength by about 48% and 17% respectively. Moreover, due to better interfacial interaction induced by MAPE, the corresponding composite exhibited better properties compared to the untreated fiber composite. Results are indicative of the fact that both mercerization and MAPE (coupling agent) have significant positive effects on the fib</span><span style="font-family:Verdana;">er</span><span style="font-family:Verdana;">-matrix interaction in terms of adhesion, wetting and dispersion, this treatment produced a better fiber distribution and consequently a more uniform composite morphology without voids and gaps between the fibers and the matrix, allowing the possibility to use higher fiber contents (up to 30% wt.) with acceptable mechanical properties.展开更多
Four parallel GaAs photoconductive semiconductor switches (PCSSs) were triggered simultaneously by four 1064 nm laser beams. The transient characteristics of four linear electrical pulses were investigated. When the...Four parallel GaAs photoconductive semiconductor switches (PCSSs) were triggered simultaneously by four 1064 nm laser beams. The transient characteristics of four linear electrical pulses were investigated. When the energy of four laser beams were 16.4 m J, 15.6 m J, 15.3 m J, and 13.7 m J, respectively, four stable electrical pulses of about 25 ns width and 10 ns rise time were obtained at the same bias voltage of 8 kV. The maximum switching voltage amplitude was 3.8 kV. With the triggering pulse energy and bias voltage kept constant, the three GaAs PCSSs were triggered at 10 Hz laser pulse. The method of synchronization calculation was given, and the synchronization of four parallel GaAs PCSSs was calculated to be 79 ps. The influence of bias voltage and laser energy on the voltage amplitude of electrical pulse was analyzed. Furthermore, relationship between the synchronization and the jitter time was also discussed.展开更多
Ferromagnetic metal fibers with a high aspect ratio (length/diameter) are attractive for use as high performance electromagnetic interference shielding materials. Ferromagnetic binary alloy fine fibers of iron-nickel,...Ferromagnetic metal fibers with a high aspect ratio (length/diameter) are attractive for use as high performance electromagnetic interference shielding materials. Ferromagnetic binary alloy fine fibers of iron-nickel, iron-cobalt and cobalt-nickel were prepared by the organic gel-thermal reduction process from the raw materials of critic acid and metal salts. These alloy fibers synthesized were featured with a diameter of about 1 μm and a length as long as 1 m. The structure, thermal decomposition process and morphologies of the gel precursors and fibers derived from thermal reduction of the gel precursors were characterized by FTIR, XRD, TG/DSC and SEM. The gel spinnability largely depends on the molecular structure of metal- carboxylates formed during the gel formation. The gel consisting of linear-type structural molecules shows good spinnability.展开更多
An experimental study on the thermal properties of iron filings and steel-fiber-reinforced concrete for solar/thermal energy storage application is presented in this report. It takes into account the results of measur...An experimental study on the thermal properties of iron filings and steel-fiber-reinforced concrete for solar/thermal energy storage application is presented in this report. It takes into account the results of measurements of thermal conductivity, thermal resistivity, thermal diffusivity and the results of compressive strength, density as well as energy storage capacity calculated from the knowledge of the above measured parameters. The experimental testing method is described as well: based upon the linear heat source theory, it requires the use of a special probe to be inserted into the sample. The experimentation was forwarded to test concrete aggregate mixtures with three different sizes and same quantity of steel fibers;two different quantities of iron filings and one plain concrete. The measurements were carried out from the pouring time of cubic samples and were ended up when hardened conditions were achieved. The results indicate that the steel fibers and iron filings have influence on the thermal and mechanical properties of the concretes tested, thus the iron filings and steel fibers reinforced concrete is suitable for better solar/thermal energy storage due to an increase in storage capacity over plain concrete.展开更多
The specimens were prepared with high alumina fiber accounting for 0. 5% , 10% or 15% by mass of the total amount of amorphous silica and high alumina fiber, using phenolic resin as binder, and extra-adding 0 or 0. 5%...The specimens were prepared with high alumina fiber accounting for 0. 5% , 10% or 15% by mass of the total amount of amorphous silica and high alumina fiber, using phenolic resin as binder, and extra-adding 0 or 0. 5% ZnO as sunscreen to cut the cost of SiO2 nanoporous insulation board. The hot volume stability and thermal conductivity (flat plate method ) of the specimens were tested and multi-Jimetion simulation equipment was used to study the thermal insulation performante. The results show that: (1) with high alumina fiber addition increasing, the linear shrinkage rate decreases, but thermal eonductivity changes a little; (2) adding ZnO can decrease thermal conductivity obviously; (3)for the specimen with ZnO and 15% of high alumina fiber, its cold face temperature hardly rises during the simulation experiment at 1 000 ℃ for 2 h, and the cold face temperature of the specimen with the smallest thickness of 2 cm doesn't exceed 180 ℃.展开更多
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 61077069 and 61107094)the Innovation Foundation for Excellent Doctoral Candidates of Beijing Jiaotong University, China (Grant No. 2011YJS202)
文摘We present a stable linear-cavity single longitudinal mode (SLM) erbium-doped silica fiber laser. It consists of four fiber Bragg gratings (FBGs) directly written in a section of photosensitive erbium-doped fiber (EDF) to form an asymmetric three-cavity structure. The stable SLM operation at a wavelength of 1545.112 nm with a 3-dB bandwidth of 0.012 nm and an optical signal-to-noise ratio (OSNR) of about 60 dB is verified experimentally. Under laboratory conditions, the performance of a power fluctuation of less than 0.05 dB observed from the power meter for 6 h and a wavelength variation of less than 0.01 nm obtained from the optical spectrum analyzer (OSA) for about 1.5 h are demonstrated. The gain fiber length is no longer limited to only several centimeters for SLM operation because of the excellent mode-selecting ability of the asymmetric three-cavity structure. The proposed scheme provides a simple and cost-effective approach to realizing a stable SLM fiber laser.
基金supported by the National Natural Science Foundation of China,No.60703045
文摘Diffusion tensor imaging is a unique method to visualize white matter fibers three-dimensionally, non-invasively and in vivo, and therefore it is an important tool for observing and researching neural regeneration. Different diffusion tensor imaging-based fiber tracking methods have been already investigated, but making the computing faster, fiber tracking longer and smoother and the details shown clearer are needed to be improved for clinical applications. This study proposed a new fiber tracking strategy based on tri-linear interpolation. We selected a patient with acute infarction of the right basal ganglia and designed experiments based on either the tri-linear interpolation algorithm or tensorline algorithm. Fiber tracking in the same regions of interest (genu of the corpus callosum) was performed separately. The validity of the tri-linear interpolation algorithm was verified by quan- titative analysis, and its feasibility in clinical diagnosis was confirmed by the contrast between tracking results and the disease condition of the patient as well as the actual brain anatomy. Statis- tical results showed that the maximum length and average length of the white matter fibers tracked by the tri-linear interpolation algorithm were significantly longer. The tracking images of the fibers indicated that this method can obtain smoother tracked fibers, more obvious orientation and clearer details. Tracking fiber abnormalities are in good agreement with the actual condition of patients, and tracking displayed fibers that passed though the corpus callosum, which was consistent with the anatomical structures of the brain. Therefore, the tri-linear interpolation algorithm can achieve a clear, anatomically correct and reliable tracking result.
文摘We present a numerical investigation of the propagation and the switching of ultra-short pulses (100 fs) in a two-core nonlinear coupler of photonic crystal fibers constructed with periodically modulated the non-linearity fiber (PMNL-PFC). Our simulations are taking into account different amplitude and frequency modulations of the PMNL-PFC. A coupler for coupling whose length is Lc = 1.8 cm, the transmission characteristics, the compression factor, the crosstalk (Xtalk) and extinction ratio (Xratio) levels of the first order solitons were studied for low to high pump energies considering 2Lc. By an analysis on the reference channel (channel 2), it is observed that at low modulation frequencies an increase occurs in the switching power increasing transmission efficiency. For high modulation frequencies, the transmitted energy efficiency loses. The switching pulses are stronger for low frequency and high amplitude modulation. The Xtalk is a function of the measurement made on the secondary channel (channel 1). It was observed that this unwanted high-frequency energy increases to lessen the measure of the amplitude modulation. In summary, we have demonstrated that introduction of a non-linearity profile takes the periodically modulated PMNL-PFC to strong variations at transmission efficiency, Xtalk, Xratio a function of frequency and modulation amplitude and the input power.
文摘In this work fibers derived from coffee</span><span style="font-family:Verdana;">,</span><span style="font-family:Verdana;"> hulls ha</span><span style="font-family:Verdana;">ve</span><span style="font-family:Verdana;"> been incorporated into Linear Low Density Polyethylene (LLDPE). The influence of the filler content on </span><span style="font-family:Verdana;">the </span><span style="font-family:Verdana;">thermal and physicomechanical properties of the composites obtained was assessed. The results showed that the incorporation of fibers was able to improve the thermostability of LLDPE/Coffee hulls fibers;comparing the treated fiber composite with untreated fiber composites, the chemical treatment reduces by 58.3% the water absorption, while increasing the elongation and tensile strength by about 48% and 17% respectively. Moreover, due to better interfacial interaction induced by MAPE, the corresponding composite exhibited better properties compared to the untreated fiber composite. Results are indicative of the fact that both mercerization and MAPE (coupling agent) have significant positive effects on the fib</span><span style="font-family:Verdana;">er</span><span style="font-family:Verdana;">-matrix interaction in terms of adhesion, wetting and dispersion, this treatment produced a better fiber distribution and consequently a more uniform composite morphology without voids and gaps between the fibers and the matrix, allowing the possibility to use higher fiber contents (up to 30% wt.) with acceptable mechanical properties.
基金supported by the Key Project of National Natural Science Foundation of China(No.50837005)the National Science Foundation of China(No.10876026)the Foundation of the State Key Laboratory of Electrical Insulation for Power Equipment(No.EIPE09203)
文摘Four parallel GaAs photoconductive semiconductor switches (PCSSs) were triggered simultaneously by four 1064 nm laser beams. The transient characteristics of four linear electrical pulses were investigated. When the energy of four laser beams were 16.4 m J, 15.6 m J, 15.3 m J, and 13.7 m J, respectively, four stable electrical pulses of about 25 ns width and 10 ns rise time were obtained at the same bias voltage of 8 kV. The maximum switching voltage amplitude was 3.8 kV. With the triggering pulse energy and bias voltage kept constant, the three GaAs PCSSs were triggered at 10 Hz laser pulse. The method of synchronization calculation was given, and the synchronization of four parallel GaAs PCSSs was calculated to be 79 ps. The influence of bias voltage and laser energy on the voltage amplitude of electrical pulse was analyzed. Furthermore, relationship between the synchronization and the jitter time was also discussed.
基金Project(50474038) supported by the National Natural Science Foundation of China
文摘Ferromagnetic metal fibers with a high aspect ratio (length/diameter) are attractive for use as high performance electromagnetic interference shielding materials. Ferromagnetic binary alloy fine fibers of iron-nickel, iron-cobalt and cobalt-nickel were prepared by the organic gel-thermal reduction process from the raw materials of critic acid and metal salts. These alloy fibers synthesized were featured with a diameter of about 1 μm and a length as long as 1 m. The structure, thermal decomposition process and morphologies of the gel precursors and fibers derived from thermal reduction of the gel precursors were characterized by FTIR, XRD, TG/DSC and SEM. The gel spinnability largely depends on the molecular structure of metal- carboxylates formed during the gel formation. The gel consisting of linear-type structural molecules shows good spinnability.
文摘An experimental study on the thermal properties of iron filings and steel-fiber-reinforced concrete for solar/thermal energy storage application is presented in this report. It takes into account the results of measurements of thermal conductivity, thermal resistivity, thermal diffusivity and the results of compressive strength, density as well as energy storage capacity calculated from the knowledge of the above measured parameters. The experimental testing method is described as well: based upon the linear heat source theory, it requires the use of a special probe to be inserted into the sample. The experimentation was forwarded to test concrete aggregate mixtures with three different sizes and same quantity of steel fibers;two different quantities of iron filings and one plain concrete. The measurements were carried out from the pouring time of cubic samples and were ended up when hardened conditions were achieved. The results indicate that the steel fibers and iron filings have influence on the thermal and mechanical properties of the concretes tested, thus the iron filings and steel fibers reinforced concrete is suitable for better solar/thermal energy storage due to an increase in storage capacity over plain concrete.
基金support of the National Natural Science Foundation of China(No.51402265,51202225,and 51272240)
文摘The specimens were prepared with high alumina fiber accounting for 0. 5% , 10% or 15% by mass of the total amount of amorphous silica and high alumina fiber, using phenolic resin as binder, and extra-adding 0 or 0. 5% ZnO as sunscreen to cut the cost of SiO2 nanoporous insulation board. The hot volume stability and thermal conductivity (flat plate method ) of the specimens were tested and multi-Jimetion simulation equipment was used to study the thermal insulation performante. The results show that: (1) with high alumina fiber addition increasing, the linear shrinkage rate decreases, but thermal eonductivity changes a little; (2) adding ZnO can decrease thermal conductivity obviously; (3)for the specimen with ZnO and 15% of high alumina fiber, its cold face temperature hardly rises during the simulation experiment at 1 000 ℃ for 2 h, and the cold face temperature of the specimen with the smallest thickness of 2 cm doesn't exceed 180 ℃.