Parameter estimation method for a linear frequency modulation signal with a Duffing oscillator based on frequency periodicity

In view of the complexity of existing linear frequency modulation(LFM)signal parameter estimation methods and the poor antinoise performance and estimation accuracy under a low signal-to-noise ratio(SNR),a parameter estimation method for LFM signals with a Duffing oscillator based on frequency periodicity is proposed in this paper.This method utilizes the characteristic that the output signal of the Duffing oscillator excited by the LFM signal changes periodically with frequency,and the modulation period of the LFM signal is estimated by autocorrelation processing of the output signal of the Duffing oscillator.On this basis,the corresponding relationship between the reference frequency of the frequencyaligned Duffing oscillator and the frequency range of the LFM signal is analyzed by the periodic power spectrum method,and the frequency information of the LFM signal is determined.Simulation results show that this method can achieve high-accuracy parameter estimation for LFM signals at an SNR of-25 dB.

Parameter estimation of LFM signals based on time reversal

In this paper,parameter estimation of linear frequency modulation(LFM)signals containing additive white Gaussian noise is studied.Because the center frequency estimation of an LFM signal is affected by the error propagation effect,resulting in a higher signal to noise ratio(SNR)threshold,a parameter estimation method for LFM signals based on time reversal is proposed.The proposed method avoids SNR loss in the process of estimating the frequency,thus reducing the SNR threshold.The simulation results show that the threshold is reduced by 5 dB compared with the discrete polynomial transform(DPT)method,and the root-mean-square error(RMSE)of the proposed estimator is close to the Cramer-Rao lower bound(CRLB).

基于FRFT的低信噪比LFM信号参数快速估计算法

基于分数阶傅里叶变换(Fractional Fourier Transform,FRFT)对线性调频(Linear Frequency Modulated,LFM)信号参数进行估计,问题关键是确定FRFT最佳阶数,根据误差迭代思想提出新的参数估计算法,该算法利用归一化带宽和旋转角的转化关系,由估计误差推算角度差值,有效降低了运算量,不需要调频斜率正负的先验信息,改进的对数搜索算法可以进一步提高参数估计结果的稳定性和可靠性。仿真结果表明,信噪比在-8 dB以上时该方法在高效率的前提下仍具有良好的参数估计性能,平均估计误差在1%以内,估计结果接近Cramer-Rao下限,满足工程实时处理需求。

脉冲噪声下基于DCNN的LFM信号去噪方法

由于脉冲噪声具有明显的尖峰脉冲特性,使得基于高斯假设的传统去噪方法无法有效滤除脉冲噪声。针对这个问题,文中提出了一种脉冲噪声下基于深度卷积神经网络(DCNN)的线性调频(LFM)信号去噪方法。首先,生成LFM信号和随机脉冲噪声,构建不同广义信噪比下的数据集,输入DCNN进行训练和测试。进而,从时域波形图、分数谱、时频分布三个方面验证模型的去噪能力。最后,对去噪LFM信号进行分数阶傅里叶变换,通过搜寻分数谱中的峰值点来估计LFM信号的参数。仿真实验结果表明,文中方法不仅能够有效去除含噪信号中的随机脉冲噪声,而且还可以保持LFM信号的时域特征、分数谱特征和时频特征基本不变,进而提高了参数估计的噪声鲁棒性。与传统的基于非线性变换的方法相比,本文方法在低信噪比下仍能有效保持信号的分数谱特征和时频特征,具有更好的去噪性能和泛化能力。

基于Z变换和改进FRI的LFM信号参数估计方法研究

为了完成线性调频(linear frequency modulation,LFM)信号的稀疏采样,并利用稀疏数据对原始信号参数进行估计,本文提出了一种基于Z变换和改进有限新息率(finite rate of innovation,FRI)的LFM信号参数估计方法。以Z变换理论为基础,设计了一种数学模型,一旦信号能够表达成该数学模型的结构形式,就能通过Z变换和零化滤波器的方法估计信号参数。然后,利用了自相关延迟的FRI结构对LFM信号采样,该结构不仅完成了LFM信号的稀疏采样,而且稀疏采样结果能够与数学模型结构相符。在理论上通过数学论证的方式证明了所提方法能够用于获取LFM信号参数信息,并通过仿真和实测数据验证了所提方法的有效性,理论和实验结果表明该方法只需要4个采样点就能实现对LFM信号的参数估计,并且实验中的参数估计误差均在3%以内,极大的提高有限新息率采样的参数估计效率。

转发式干扰条件下LFM雷达的检测概率估计

对多雷达干扰效果评估的难点在于分析干扰机对非目标雷达的影响。针对干扰机转发一部线性调频(linear frequency modulation,LFM)雷达的信号无意干扰另一部LFM雷达时的检测概率估计问题,首先计算了被干扰雷达对干扰信号在空域、频域和时域上的接收增益;其次将干扰信号在判决单元中的统计特性建模为非中心卡方分布,并给出了检测概率和虚警概率的计算方法。仿真结果表明,在一部干扰机的无意干扰下,估计的检测概率可作为被干扰雷达检测概率的上限;为达到同样的干扰效果,转发非目标雷达的信号实施干扰,比转发目标雷达的信号进行干扰所需的干扰功率更少。

MSK-LFM一体化信号波形相关性分析与参数选择

以二进制数字信号最佳接收准则为依据,分析了MSK-LFM雷达通信一体化信号不同码元对应波形的相关性。利用fresnel函数得到了波形相关系数的表达式;通过数值仿真得到了相关系数随LFM信号的初始频率、调频率、脉冲内码元调制速率等参数的变化关系;构建MSK-LFM信号正交调制、解调仿真模型进行验证。研究表明,通过增大初始频率、调频率或减少调制速率可降低信号误码率;当初始频率远大于脉冲内码元调制速率时可认为不同码元波形正交。

Chirp-Rate Resolution of Fractional Fourier Transform in Multi-component LFM Signal

Distinguishing close chirp-rates of different linear frequency modulation （LFM） signals under concentrated and complicated signal environment was studied. Firstly, detection and parameter estimation of multi-component LFM signal were used by discrete fast fractional Fourier transform （FrFT）. Then the expression of chirp-rate resolution in fractional Fourier domain （FrFD） was deduced from discrete normalize time-frequency distribution, when multi-component LFM signal had only one center frequency. Furthermore, the detail influence of the sampling time, sampling frequency and chirp-rate upon the resolution was analyzed by partial differential equation. Simulation results and analysis indicate that increasing the sampling time can enhance the resolution, but the influence of the sampling frequency can he omitted. What＇s more, in multi-component LFM signal, the chirp-rate resolution of FrFT is no less than a minimal value, and it mainly dependent on the biggest value of chirp-rates, with which it has an approximately positive exponential relationship.

Wigner-Hough transform based on slice's entropy and its application to multi-LFM signal detection

To enhance the capacity of the radar-reconnaissance interception receiver recognizing linear frequency modulated (LFM) at a low signal-noise ratio, this paper presents WignerHough transform (WHT) of the LFM signal and its corresponding characteristics, derives the probability density functions of the LFM signal and Gaussian white noise within WHT based on entropy (WHTE), dimension under different assumptions and puts forward a WHT algorithm based on entropy of slice to improve the capacity of detecting the LFM signal. Entropy of the WHT domain slice is adopted to assess the information size of polar radius or angle slice, which is converted into the weight factor to weight every slice. Double-deck weight is used to weaken the influences of noise and disturbance terms and WHTE treatment and signal detection procedure are also summarized. The rationality of the algorithm is demonstrated through theoretical analysis and formula derivation, the efficiency of the algorithm is verified by simulation comparison between WHT, fractional Fourier transform and periodic WHT, and it is highlighted that the WHTE algorithm has better detection accuracy and range of application against strong noise background.

Combining Radon-ambiguity transform with second-order difference to improve detection probability of LFM signals in low SNR

The Radon-ambiguity transform （RAT）, although efficient for detecting the linear frequency modulated signals （LFMs）, is troubled by the energy accumulation of noise in low signal-to-noise ratio （SNR）. A secondorder difference （SOD） method is proposed to treat with this problem. In the SOD method, the optimal search step and difference step are derived from the LFM rate resolution formula. The sharpness of the peaks of RAT is measured by curvature, and the sharpness, but not the magnitude of the peaks, is used to detect the LFMs. The SOD method removes the noise energy accumulation and reserves the drastically changing components integrally; thus, it improves the detection probability of LFMs in low SNR. The expected performance of the new method is verified by 100 Monte Carlo simulations.

ALGORITHM FOR THE DETECTION AND PARAMETER ESTIMATION OF MULTICOMPONENT LFM SIGNALS

A novel algorithm based on Radon-Ambiguity Transform (RAT) and Adaptive Signal Decomposition (ASD) is presented for the detection and parameter estimation of multicompo-nent Linear Frequency Modulated (LFM) signals. The key problem lies in the chirplet estimation. Genetic algorithm is employed to search for the optimization parameter of chirplet. High estimation accuracy can be obtained even at low Signal-to-Noisc Ratio(SNR). Finally simulation results are provided to demonstrate the performance of the proposed algorithm.

Statistical performance of IF estimation of LFM signals with timevarying amplitude using the peak of WVD

The instantaneous frequency （IF） estimation of the linear frequency modulated （LFM） signals with time-varying amplitude using the peak of the Wigner-Ville distribution （WVD） is studied. Theoretical analysis shows that the estimation on LFM signals with time-varying amplitude is unbiased, only if WVD of time-varying amplitude reaches its maximum at frequency zero no matter in which time. The statistical performance in the case of additive white Guassian noise is evaluated and an analytical expression for the variance is provided. The simulations using LFM signals with Gaussian envelope testify that IF can be estimated accurately using the peak of WVD for four models of amplitude variation. Furthermore the statistical result of estimation on the signals with amplitude descending before rising is better than that of the signals with constant amplitude when the amplitude variation rate is moderate.

HIGH RESOLUTION RANGE PROFILE FORMATION BASED ON LFM SIGNAL FUSION OF MULTIPLE RADARS

This paper presents a new method of High Resolution Range (HRR) profile formation based on Linear Frequency Modulation (LFM) signal fusion of multiple radars with multiple frequency bands. The principle of the multiple radars signal fusion improving the range resolution is analyzed. With the analysis of return signals received by two radars,it is derived that the phase difference between the echoes varies almost linearly with respect to the frequency if the distance between two radars is neg-ligible compared with the radar observation distance. To compensate the phase difference,an en-tropy-minimization principle based compensation algorithm is proposed. During the fusion process,the B-splines interpolation method is applied to resample the signals for Fourier transform imaging. The theoretical analysis and simulations results show the proposed method can effectively increase signal bandwidth and provide a high resolution range profile.

Generalized Parseval’s Theorem on Fractional Fourier Transform for Discrete Signals and Filtering of LFM Signals

This paper investigates the generalized Parseval’s theorem of fractional Fourier transform (FRFT) for concentrated data. Also, in the framework of multiple FRFT domains, Parseval’s theorem reduces to an inequality with lower and upper bounds associated with FRFT parameters, named as generalized Parseval’s theorem by us. These results theoretically provide potential valuable applications in filtering, and examples of filtering for LFM signals in FRFT domains are demonstrated to support the derived conclusions.

基于相位重构的LFM信号间歇采样干扰产生方法研究

目前,对线性调频信号采用间歇采样干扰样式是电子自卫干扰的常用方法。由于收发延迟,干扰主峰落后于目标回波,但间歇采样可以获取超前于主峰信号的次峰目标。在线性调频斜率较小时,次峰目标甚至可以超前于被保护目标,但线性调频斜率较大时,次峰距离主峰近,效果难以得到保证。提出一种新方法,该方法基于相位信息通过对相位的线性拟合重构信号实现了信号的近似复原,使得主峰相对于回波的延迟被消除,且保持了良好的相参特性。

基于线性调频连续波的合作式通信辐射源测距

针对加速运动目标参数估计中,离散多项式变换方法无法进行非整数估计的问题,本文提出基于瑞夫算法的离散多项式变换法和基于Chirp-Z变换的离散多项式变换法2种新型离散多项式变换算法,对加速运动目标速度和加速度进行估计,并对2种算法的估计误差和计算量进行了分析比较。结果表明:2种算法在信噪比-20 dB时均方误差开始接近克拉美罗界。基于瑞夫算法的离散多项式变换法与3次迭代基于Chirp-Z变换的离散多项式变换法均可在较低信噪比下可实现任意频率的有效估计且性能接近,二者均可实现低信噪比下速度、加速度的有效估计,但基于瑞夫算法的离散多项式变换法计算量远小于3次迭代基于Chirp-Z变换的离散多项式变换法。

面向高速移动环境的二级信号检测算法

正交时间序列复用(OTSM)可以以更低的复杂度实现类似正交时频空间(OTFS)调制的传输性能,为未来需要低复杂度收发器的高速移动性通信系统提供一种有前景的解决方法。针对现有的基于时域的高斯-赛德尔(GS)迭代均衡效率不高的问题,提出二级信号检测算法。首先在时域进行低复杂度线性最小均方误差(LMMSE)检测,其次采用连续超松弛(SOR)迭代算法进一步消除残余符号干扰。为进一步提高收敛效率和检测性能,对SOR算法进行线性优化得到改进SOR(ISOR)算法。仿真实验结果表明,与SOR算法相比,ISOR算法在增加较低复杂度前提下可以提升检测性能并加快算法收敛。与GS迭代算法相比,ISOR算法采用16QAM调制且误码率为10-4时有1.61 dB的增益。

基于高斯短时分数阶傅里叶变换的多分量LFM信号检测与参数估计

该文针对线性调频信号,提出一种基于分数阶波包变换分析方法——高斯短时分数阶傅里叶变换。通过旋转角度的搜索及高斯窗口宽度的调整,能够在低信噪比条件下对多分量LFM信号进行检测,避免交叉项的出现,并能得到参数的估计值。通过推导分析给出变换结果的解析表达式,计算机仿真结果也表明了该变换的有效性。

高精度LFM信号参数估计的谱校正方法

为精确估计噪声背景下线性调频(linear frequency modulation,LFM)信号的调频率和中心频率等参数,提出了一种基于Radon模糊变换(Radon-ambiguity transform,RAT)和分数阶傅里叶变换(fractional Fourier transform,FRFT)的离散谱校正估计方法。该方法将LFM信号的调频率和中心频率估计问题转化为模糊域和分数阶Fourier域上的两次一维谱峰搜索过程,并且通过对矩形窗截断的LFM信号的RAT和FRFT谱线结构分析,将能量重心谱校正法引入两次谱峰搜索过程,在不增加运算量的基础上实现了谱峰位置的超分辨率估计,较大幅度地提高了信号的参数估计精度。仿真结果显示,对于单分量LFM信号情况,该方法对信号的RAT和FRFT谱峰位置的校正误差分别降到了扫描步长的1.55%和4.94%,证明了该方法的有效性。

LFM-BPSK复合调制信号识别与参数估计

首先介绍了相位编码与线性调频(Linear frequency modulation and binary phase shift keying,LFM-BPSK)复合调制信号的模型,并分析了其相位特征及概率密度函数,然后通过分段滤波提高信号的输出信噪比。采用二叉树方法,基于相位展开和瞬时频率对LFM-BPSK复合调制信号、BPSK信号和LFM信号进行了识别,并讨论和分析了纽曼-皮尔逊(N-P)准则下识别门限的选取。接着对LFM-BPSK复合调制信号进行参数估计;最后用Matlab对LFM-BPSK复合调制信号的识别进行了仿真验证,并对识别后的信号进行了参数估计的仿真。结果表明,本文方法在较低信噪比下仍能实现较好的识别性能和参数估计精度。