Analysis of diffusion-adsorption equivalency of landfill liner systems for organic contaminants

The equivalence between multilayered barriers regarding diffusion and adsorption was studied. The bottom boundary of the liner system is defined by assuming concentration continuous and flux continuous conditions of the contaminant between the bottom liner layer and the underlying soil. Five different liner systems were compared in terms of solute breakthrough time. The results of the analysis showed that breakthrough time of the hydrophobic organic compounds for a 2-meter-thick compacted clay liner （CCL） could be 3-4 orders of magnitude is greater than the breakthrough time for a geosynthetic clay liner （GCL） composite liner. The GM/GCL and GM/CCL composite liner systems provide a better diffusion barrier for the hydrophilic organic compounds than that for the hydrophobic compounds due to their different Henry＇s coefficient. The calculated breakthrough times of the organic contaminants for the Chinese standard liner systems were found to be generally greater than those for the GCL alternatives, for the specific conditions examined. If the distribution coefficient increases to 2.8 for the hydrophobic compounds or 1.0 for the hydrophilic compounds, the thickness of the attenuation layer needed to achieve the same breakthrough time as the standard liner systems can be reduced by a factor of about 1.9-2.4. As far as diffusive and adsorption contaminant transport are concerned, GM or GCL is less effective than CCL.

Controlling strain in geosynthetic liner systems used in vertically expanded landfills

According to relevant new regulations in China,a composite liner system involving geosynthetic materials must be installed at the bottom of an expanded landfill.The deformation and integrity of the composite liner under a variety of factors are important issue to be considered in the design of a landfill expansion.In this paper,we investigate the strain distribution in geosynthetic materials within the composite liner system of expanded landfills,including strains in geosynthetic materials resulting from overall settlement and lateral movement of landfills,localized subsidence in landfills,and differential settlement around gas venting wells.The allowable strains of geosynthetic materials are discussed based on the results of tensile tests,and the corresponding design criteria for composite liner systems are proposed.Meanwhile,practical measures allowing strain control in geosynthetic materials used in landfill engineering are proposed.

Critical interfaces in geosynthetic multilayer liner system of a landfill

This study is to identify the critical interface in a geosynthetic multilayer liner system by examining the effects of the interface shear strength of liner components, leachate level, leachate buildup cases, and peak and residual interface strengths. According to current landfill design procedures, conducting stability analysis along the same interface at both the back slope and base may result in a non-conservative result. The critical interfaces with the minimum factor of safety are generally found at different locations along the back slope and base. The critical interface for a multilayer liner system cannot simply be assumed during stability analysis. It can shift from one interface to another with changes in the leachate level and with different leachate buildup cases. The factor of safety for an interface with a high friction angle and low apparent cohesion generally drops much more quickly than it does under inverse conditions when the leachate level increases. The failure interface in a liner system under residual conditions is usually different from the failure interface under peak conditions.

Effect of temperature on tribofilm growth and the lubrication of the piston ring-cylinder liner system in two-stroke marine engines

This study is an optimized extension based on the authors’previous research on the tribo-chemical reaction under constant temperature field of two-stroke internal combustion engines(ICEs).It establishes a coupled analysis model that considers the tribo-chemical reactions,dynamic contact,and interface lubrication of the piston ring-cylinder liner(PRCL)system under transient temperature conditions.In this study,for the first time,the prediction of the tribofilm thickness and its influence on the surface micro-topography(the comprehensive roughness)are coupled in the working temperature field of the PRCL system,forming an effective model framework and providing a model basis and analytical basis for subsequent research.This study findings reveal that by incorporating temperature and tribofilm into the simulation model,the average friction deviation throughout the stroke decreases from 8.92%to 0.93%when compared to experimental results.Moreover,the deviation during the combustion regime reduces from 39.56%to 7.34%.The proposed coupled model provides a valuable tool for the evaluation of lubrication performance of the PRCL system and supports the analysis software forward design in two-stroke ICEs.

Jet formation and penetration performance of a double-layer charge liner with chemically-deposited tungsten as the inner liner

This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double-layer charge liners were fabricated by using CVD to deposit tungsten layers on the inner surfaces of pure T2 copper liners.The microstructures of the tungsten layers were analyzed using a scanning electron microscope(SEM).The feasibility analysis was carried out by pulsed X-rays,slug-retrieval test and static penetration tests.The shaped charge jet forming and penetration law of inner tungsten-coated double-layer liner were studied by numerical simulation method.The results showed that the double-layer liners could form well-shaped jets.The errors between the X-ray test results and the numerical results were within 11.07%.A slug-retrieval test was found that the retrieved slug was similar to a numerically simulated slug.Compared with the traditional pure copper shaped charge jet,the penetration depth of the double-layer shaped charge liner increased by 11.4% and>10.8% respectively.In summary,the test results are good,and the numerical simulation is in good agreement with the test,which verified the feasibility of using the CVD method to fabricate double-layer charge liners with a high-density and high-strength refractory metal as the inner liner.

Integrated design and control technology of liner completion and drilling for horizontal wells

Aiming at the problems of large load of rotation drive system,low efficiency of torque transmission and high cost for operation and maintenance of liner steering drilling system for the horizontal well,a new method of liner differential rotary drilling with double tubular strings in the horizontal well is proposed.The technical principle of this method is revealed,supporting tools such as the differential rotation transducer,composite rotary steering system and the hanger are designed,and technological process is optimized.A tool face control technique of steering drilling assembly is proposed and the calculation model of extension limit of liner differential rotary drilling with double tubular strings in horizontal well is established.These results show that the liner differential rotary drilling with double tubular strings is equipped with measurement while drilling(MWD)and positive displacement motor(PDM),and directional drilling of horizontal well is realized by adjusting rotary speed of drill pipe to control the tool face of PDM.Based on the engineering case of deep coalbed methane horizontal well in the eastern margin of Ordos Basin,the extension limit of horizontal drilling with double tubular strings is calculated.Compared with the conventional liner drilling method,the liner differential rotary drilling with double tubular strings increases the extension limit value of horizontal well significantly.The research findings provide useful reference for the integrated design and control of liner completion and drilling of horizontal wells.

Machine learning optimization strategy of shaped charge liner structure based on jet penetration efficiency

Shaped charge liner(SCL)has been extensively applied in oil recovery and defense industries.Achieving superior penetration capability through optimizing SCL structures presents a substantial challenge due to intricate rate-dependent processes involving detonation-driven liner collapse,high-speed jet stretching,and penetration.This study introduces an innovative optimization strategy for SCL structures that employs jet penetration efficiency as the primary objective function.The strategy combines experimentally validated finite element method with machine learning(FEM-ML).We propose a novel jet penetration efficiency index derived from enhanced cutoff velocity and shape characteristics of the jet via machine learning.This index effectively evaluates the jet penetration performance.Furthermore,a multi-model fusion based on a machine learning optimization method,called XGBOOST-MFO,is put forward to optimize SCL structure over a large input space.The strategy's feasibility is demonstrated through the optimization of copper SCL implemented via the FEM-ML strategy.Finally,this strategy is extended to optimize the structure of the recently emerging CrMnFeCoNi high-entropy alloy conical liners and hemispherical copper liners.Therefore,the strategy can provide helpful guidance for the engineering design of SCL.

Simulation Study of Solid Rocket Motor C/C Throat Liner Ablation Based on Two Regions

Based on the ablation micro-morphological characteristics, thermo-chemical ablation mechanism, and mechanical stripping mechanism, a dual-region solid rocket motor C/C throat liner ablation model and physical model are established. The ablation program was written and the experimental data of 70 lb BATES engine platform was used for model validation. The relative errors between the simulation calculation results and the experimental results were −6.83% - 10.20%. The ablation program was applied to study the effects of combustion chamber temperature, pressure, oxidation component concentration, throat particle concentration and particle scouring angle on the nozzle throat liner, which provides a reference for the design of the nozzle throat liner and the estimation of solid rocket motor ablation.

GO/HTPB composite liner for anti-migration of small molecules

Hydroxyl-terminated polybutadiene/toluene diisocyanate(HTPB/TDI)system is widely used in composite solid propellants.The migrations of plasticizers and water molecules from solid propellants and surrounding environment to the inhibitor have always been the important issues.This study focuses on the preparation,characterization and anti-migration behavior of graphene oxide(GO)/HTPB nanocomposite liner.The GO/HTPB(GH)composite liners affect the migration of small molecules through a tighter cross-linked structure and weakening function of small molecule adsorption.The anti-migration performance of the liner at different temperatures was analyzed,and the influence of the added amount of GO on the anti-migration performance and adhesion performance was also systematically studied.The overall performance of the liner is optimized when the amount of GO filler is 0.3 wt%.After adding 0.3 wt%GO,the concentration of dioctyl sebacate(DOS)migrated into the liner is decreased by 23.28%,and the concentration of water molecules is decreased by 51.89%,indicating that the introduction of GO can significantly improve the anti-migration performance of the liner.In addition,the bond strength is greatly increased from 0.25 MPa to 0.95 MPa,which meets the application requirements of the current propellant system.This research provides an important way for the preparation of structure-function synergistic anti-migration composite liners.

Viscoelastic Burger’s model for tunnels supported with tangentially yielding liner

This study proposed an analytical model for the tunnel supported with a tangentially yielding liner in viscoelastic ground.The efficiency of the developed analytical model was verified by comparing the calculated results with associated numerical simulation results.Using the analytical model,a comprehensive parameter sensitivity analysis was performed to examine the effects of the rate of tunnel face advancement,concrete liner thickness,installation time of liner,and strength and thickness of yielding elements on the tunnel responses.The results highlight the significant benefit of the tangentially yielding liner to relieve overstress in the tunnel liner and improve the stability of the tunnel.The yield efficiency of the tangentially yielding liner depends highly on the yielding strength and deformable capacity of the yielding elements and less on the installation time.

THE NUMERICAL ANALYSIS OF UNSTEADY HEAT TRANSFER OF A PISTON-LINER COUPLED SYSTEM IN AN INTERNAL COMBUSTION ENGINE

This paper provides a numerical analysis model of unsteady heat trans-fer in piston-liner set of an internal combustion engine.The model simulates the un-steady heat transfer process among the combustion mixture,piston set,lubricantfilm,liner and coolant in a whole engine cycle,and can predict the temperature fluc-tuation and distribution on piston crown,inner surface of liner,piston ring and thelubricant film.A computer program is developed to calculate the unsteady heat trans-fer process of piston-liner system in a water-cooled diesel engine.

The Efect of Rich Synthetic Copper-rich Solution on Antiseepage Dense Pre-hydration Geosynthetic Clay Liner

Dense pre-hydrated geosynthetic clay liners(DPH GCLs)were manufactured as innovative materials accompanied by the advantage of lower hydraulic conductivity(k).The k of DPH GCLs permeated with de-ionized water(DIW)was 9.8×10^(−12) m/s.The effect of Cu^(2+)synthetic solution on DPH GCLs was discussed.Furthermore,the effect mechanism was studied on the basis of test technologies.A significant adverse impact on hydraulic performance of DPH GCLs is found when the concentration of Cu^(2+)is greater than 1 g/L.SEM,XRD,XRF,FTIR,and XPS analyses show that the effect of Cu^(2+)on DPH GCLs includes two steps.Firstly,Cu^(2+)interacts with hydrophobic organic matter(HOM),and the adhesion of bentonite is destroyed,and some holes appear.The Cu^(2+)contacts with bentonite directly,and Cu^(2+)interacts with bentonite through ion exchange.Passivated phenomenon occurs on the surface of the bentonite,and swelling ability of bentonite is reduced,which causes permeable DPH GCLs.

Structural design of the fluted shaped charge liner using multi-section optimization method

Spin effect of the small diameter shaped charge results in the centrifugal stress during the jet stretching process. Consequently, the jet scatters, which deceases the jet penetration capability. In the present study, a multi-section method was proposed to design the spin-compensation liner. The spincompensation rate(SCR) of the liner was defined as the specific angular velocity that a fluted liner can offset. Based on the plain stress theory, SPH numerical method was applied to study the converging process of the 2D fluted structure. The spin-compensation mechanism of the fluted structure was illustrated. Then, nine cross sections were chosen along the liner axis equidistantly. On each of the section, a 2D fluted structure was designed to offset a given initial angular velocity. After, the optimized fluted structures were integrated into a 3D fluted liner. Jet appearances of the normal liner and the fluted liners under different initial angular velocities were compared, which verifies the practicality of the multi-sectional method. The multi-section optimization method provides a new efficient method of designing the shaped charge liner for a specific usage.

Parameter Study on a Composite Sound-Absorbing Structure Liner in Elevator Shafts

With the growing global environmental awareness,the development of renewable and green materials has gained increased worldwide interest to substitute conventional materials and are favorable for sustainable economic development.This paper proposed a novel eco-friendly sound absorbing structure(NSAS)liner for noise reduction in elevator shafts.The base layer integrated with the shaft walls is a damping gypsum mortarboard,and a rock wool board and a perforated cement mortarboard are used to compose the NSAS.Based on the acoustic impedance theory of porous materials and perforated panels,the sound absorption theory of the NSAS was proposed;the parameter effects of the rock wool board(flow resistivity,porosity,structure factor)and perforated panel(perforated rates,thickness,density,perforated diameter)on NSAS absorption were discussed theoretically for absorption improvement,and experiments were also conducted.Numerical results showed that the perforation rate,the thickness of the perforated plate,and the porosity,flow resistance,and volume density of the rock wool board played a key issue in the absorption performances of the NSAS.Experiments verified the accuracy of the proposed theoretical model.Wideband sound absorption performance of the NSAS at frequencies between 500–1600 Hz was achieved in both numerical analysis and experiments,and the sound absorption coefficient was improved to 0.72 around 1000 Hz after parameter adjustments.The NSAS proposed in this paper can also be made of other renewable materials with preferable structure strength and still has the potential to broaden the absorption bandwidth.It can provide a reference for controlling the elevator shaft noise.

填埋场底部有水循环管情况下温度变化分析

为了减少填埋场中温度升高对衬垫系统的危害,对填埋场底部有水循环管情况下衬垫层温度变化进行研究。针对水循环系统建立了热传导数学模型,并求得了解析解,通过与Comsol的对比,验证了模型及其解答的正确性。根据解析解分析了不同情况下水循环系统对垃圾填埋场衬垫系统温度的影响情况。研究表明,循环水温度和热交换系数对水循环管的降温性能有较大的影响,水循环管对上下层周围土体的温度也有影响,影响范围为4 m左右。

基于CPA-FM-MEM磨粒分析的缸套-活塞系统健康状态评估

以内燃机典型摩擦副缸套-活塞系统为研究对象,设计和搭建内燃机缸套-活塞系统状态监测试验台。针对传统最大熵方法分析润滑油中磨粒监测数据存在的缺点,提出改进的分数矩最大熵方法(Fractional Moment Maximum Entropy Method, FM-MEM),并结合食肉植物优化算法(Carnivorous Plant Algorithm, CPA)对关键参数进行寻优求解。对润滑油中磨粒监测数据进行阈值划分,实现内燃机健康状态评估,然后将理论与试验相结合,以在线磨粒监测为主,从润滑油磨粒、理化指标以及表面形貌3个方面对内燃机缸套-活塞系统的运行状态进行监测,分析低速工况下缸套-活塞系统各个时间段的磨损健康状态及磨粒含量变化趋势,通过内燃机整机的在线磨粒监测试验,证明该方法可实现对内燃机缸套-活塞系统的实时状态监测。

Selection of shaped charges parameters for producing aluminum particles with velocities in the range of 2.5-16 km/s

Testing rocket and space technology objects in ground conditions for resistance to the impact of meteoroids and fragments of space debris can be carried out using shaped charges. To substantiate the design parameters of shaped charges that ensure the formation of aluminum particles in a wide velocity range(from 2.5 to 16 km/s), numerical modeling of the formation process was carried out within the framework of a two-dimensional axisymmetric problem of continuum mechanics using three different computing codes to increase the reliability of the results. The calculations consider shaped charges with a diameter of 20-100 mm with aluminum liners of various shapes. It is shown that the formation of particles with velocities close to the lower limit of the considered range is ensured by gently sloping segmental liners of degressive thickness. To form higher-velocity particles with velocities over 5 km/s, it is proposed to use combined liners, the jet-forming part of which has the shape of a hemisphere of constant thickness or the shape of a semi-ellipsoid or semi-superellipsoid of rotation of degressive thickness.

Formation behaviors of rod-like reactive shaped charge penetrator and their effects on damage capability

Formation behaviors of rod-like reactive shaped charge penetrator(RRSCP)and their effects on damage capability are investigated by experiments and numerical simulations.The pulsed X-ray technology and a spaced aluminum/steel plate with the thicknesses of 5 mm/100 mm are used.Three types of sphericalsegment aluminum-polytetrafluoroethylene-copper(Al-PTFE-Cu)reactive liners with Cu contents of 0%,46.6%,and 66%are fabricated and tested.The experimental results show that the reactive liners can form excellent rod-shaped penetrators with tail skirts under the shaped charge effect,but the tail skirts disappear over time.Moreover,rupturing damage to the aluminum plate and penetration to the steel plate are caused by the RRSCP impact.From simulation analysis,the RRSCP is formed by a mechanically and chemically coupled response with the reactive liner activated by shock in its outer walls and bottom and then backward overturning,forming a leading reactive penetrator and a following chemical energy cluster.The unique formation structure determines the damage modes of the aluminum plate and the steel plate.Further analysis indicates that the formation behaviors and damage capability of Al-PTFE-Cu RRSCP strongly depend on Cu content.With increasing Cu content,the velocity,activation extent,and reaction extent of Al-PTFE-Cu RRSCP decrease,which contribute to elongation and alleviate the negative effects of chemical reactions on elongation,significantly increasing the length-diameter ratio and thus enhancing the capability of steel plate penetration.However,the lower activation extent and energetic density will weaken the RRSCP's capability of causing rupturing damage to the aluminum plate.

Feasibility of compacted attapulgite/diatomite amended clayey soils as gas barrier materials

Compacted clay liners are extensively used as barriers to control the upward diffusion of vapors of volatile or semi-volatile organic contaminants released from unsaturated contaminated soils at industrycontaminated sites.This study aimed to investigate the gas diffusion barrier performance of compacted clayey soils amended with three agents including attapulgite and diatomite individually,and attapulgite/diatomite mixture.The properties including water retention,volumetric shrinkage,gas diffusion,and unconfined compressive strength were evaluated through a series of laboratory tests of amended compacted clayey soils.The results demonstrate that the decrease in volume proportions of interaggregate pores leads to an increase in unconfined compressive strength(qu).Both hydrophilic groups and microstructures of attapulgite and diatomite result in an increase in water retention percent(Wt)of compacted clayey soil specimens after amendment regardless of the type of agent or initial water content(w0).Furthermore,the ratio of the gas diffusion coefficient(De)to the gas diffusion coefficient in the air(Da)was significantly reduced owing to a decrease in volume proportions of inter-aggregate pores,hydrophilic group,and microstructures of attapulgite and diatomite.Scanning electron microscope analyses revealed that rod-shaped attapulgite filled the inter-aggregate pores formed by clay particles,whereas the disc-shaped diatomite particles,characterized by micropores,failed to obstruct the interaggregate pores due to their larger particle size.Mercury intrusion porosimetry(MIP)analyses showed a reduction in pore volume in the inter-aggregate pores,leading to a reduction in the total pore volume for both the attapulgite and attapulgite/diatomite mixture amended clays,which is in accordance with the scanning electron microscope(SEM)results.The findings are pertinent to the practical application of compacted clay liners as gas barriers against the upward migration of volatile or semi-volatile organic contaminants at contaminated sites.

Impact of surface-reflected seismic waves on the seismic isolation performance of circular tunnel isolation layers

Seismic isolation is an effective strategy to mitigate the risk of seismic damage in tunnels.However,the impact of surface-reflected seismic waves on the effectiveness of tunnel isolation layers remains under explored.In this study,we employ the wave function expansion method to provide analytical solutions for the dynamic responses of linings in an elastic half-space and an infinite elastic space.By comparing the results of the two models,we investigate the seismic isolation effect of tunnel isolation layers induced by reflected seismic waves.Our findings reveal significant differences in the dynamic responses of the lining in the elastic half-space and the infinitely elastic space.Specifically,the dynamic stress concentration factor(DSCF)of the lining in the elastic half-space exhibits periodic fluctuations,influenced by the incident wave frequency and tunnel depth,while the DSCF in the infinitely elastic space remain stable.Overall,the seismic isolation application of the tunnel isolation layer is found to be less affected by surface-reflected seismic waves.Our results provide valuable insights for the design and assessment of the seismic isolation effect of tunnel isolation layers.