A Comparative Investigation of the Biodegradation Behaviour of Linseed Oil-Based Cross-Linked Composites Filled with Industrial Waste Materials in Two Different Soils

The biodegradation of polymeric biocomposites formed from epoxidized linseed oil and various types of fillers(pine needles,pine bark,grain mill waste,rapeseed cake)and a control sample without filler was studied during 180 days of exposure to two types of forest soil:deciduous and coniferous.The weight loss,morphological,and structural changes of polymer composites were noticed after 180 days of the soil burial test.The greatest weight loss of all tested samples was observed in coniferous forest soil(41.8%–63.2%),while in deciduous forest soil,it ranged between 37.7%and 42.3%.The most significant changes in the intensities of the signals evaluated by attenuated total reflectance infrared spectroscopy,as well as morphological changes determined by scanning electron microscopy,were assessed for polymer composite with rapeseed cake and specimen without filler in coniferous forest soil and are in a good agreement with weight loss results.Whereas significantly lower changes in weight loss,morphology,and structure of polymeric film with pine bark were noticed in both soils.It was suggested that fungi of Trichoderma,Penicillium,Talaromyces and Clonostachys genera are the possible soil microorganisms that degrade linseed oil-based cross-linked polymer composites.Moreover,the novel polymer composites have the potential to be an environmentally friendly alternative to petroleum-based mulching films.

Green Composite Material Made from Typha latifolia Fibres Bonded with an Epoxidized Linseed Oil/Tall Oil-Based Polyamide Binder System

Here,we report the mechanical and water sorption properties of a green composite based on Typha latifolia fibres.The composite was prepared either completely binder-less or bonded with 10%(w/w)of a bio-based resin which was a mixture of an epoxidized linseed oil and a tall-oil based polyamide.The flexural modulus of elasticity,the flexural strength and the water absorption of hot pressed Typha panels were measured and the influence of pressing time and panel density on these properties was investigated.The cure kinetics of the biobased resin was analyzed by differential scanning calorimetry(DSC)in combination with the iso-conversional kinetic analysis method of Vyazovkin to derive the curing conditions required for achieving completely cured resin.For the binderless Typha panels the best technological properties were achieved for panels with high density.By adding 10%of the binder resin the flexural strength and especially the water absorption were improved significantly.

Properties of Polyurethane Coatings Based on Linseed Oil Phosphate Ester Polyol

Linseed oil was epoxidized using hydrogen peroxide (H2O2), acetic acid (AcOH) and ion exchange resin AmberliteIR-120 as a catalyst. Epoxidized oil was separately dissolved in isopropyl alcohol (IPA) or diethylene glycol butylether (DGBE) and phosphorylated with different amounts of phosphoric (H3PO4) acid (1%, 2%, 3% and 5%). Theformation of phosphate polyesters was confirmed by Fourier-transform infrared (FTIR) and 31P nuclearmagnetic resonance (NMR) spectra. Based on the synthesized polyols, polyurethane (PU) coatings were prepared.PU coating based on linseed oil diethylene glycol ester polyol was used as the reference. For the characterizationof coatings, mechanical tests and thermogravimetric analysis (TGA) were used. The flammability parameters ofwood samples with PU coatings at a heat flux of 35 kW/m2 were determined. It was found that PU coatings basedon IPA polyols had higher mechanical characteristics, char residue upon thermal decomposition and flameretardancy.

Thermal Properties of the Product of Palm Stearin and Linseed Oil Transesterification

Triacylglycerols are the main constituents of natural fats and oils and contribute directly to their texture and flavor. The DSC （differential scanning calorimetry） of fats and oils is usually performed in order to characterize their melting and crystallization characteristics. The effect of the chemically catalyzed interesterification of two vegetable oils, i.e. palm stearin and linseed oil, on the thermal behavior of the product is studied. The objective of this study is to analyze the impact of the transesterification reaction conditions and of the initial amounts of oils on the thermal behavior of the product. This work shows that both cooling and heating DSC thermograms undergo significant changes as the result of the mixture of linseed oil and palm stearin and of their transesterification.

Effects of Maternal Linseed Oil Supplementation on Metabolic Parameters in Cafeteria Diet-induced Obese Rats

Because linseed oil may influence maternal and fetal metabolisms, we investigated its role in the modulation of lipid metabolism in cafeteria diet-induced obese rats and their offspring. Female Wistar rats were fed control or cafeteria food, which were either supplemented or not supplemented with linseed oil （5%） for I month before and during gestation. At parturition, serum and tissue lipids and enzyme activities were analyzed. Cafeteria diet induced adverse metabolic alterations in both mothers and offspring. Linseed oil improved metabolic status. In conclusion, linseed oil displayed health benefits by modulating tissue enzyme activities in both obese mothers and their newborns.

Feeding Calcium Salts of Linseed Oil on Productive Performance and Milk Fatty Acid Profile in Grazing Dairy Cows

The objective of this study was to determine the effect of supplying calcium salts of linseed oil (Ca-FA) rich in omega-3 (α-linolenic acid) on the production and chemical composition of milk and its nutraceutical value in dairy cows in early lactation. The trial lasted 12 weeks (2 weeks for adaptation to lipids and 10 weeks of data collection). A total of 36 Holstein dairy cows with 58.0 ± 17.0 days in milk (DIM), 594.1 ± 92.4 kg BW, 2.6 ± 1.5 parity and 38.9 ± 9.3 kg milk day-1 were used in a randomized complete block design. The treatments were: 1) Omega-3 (O3): 5.2 kg DM day-1 of concentrate including 0.7 kg DM of Ca-FA + 13.5 kg DM day-1 of partial mixed ration (PMR) + 12 kg DM day-1 of alfalfa pasture (Medicago sativa) and 2) Control (C): diet similar to O3 but lipid supplementation was replaced by cracked corn grain so that the diets were isoenergetic. No treatment effect was detected (P > 0.05) for any milk production and composition variables, except for urea in milk that was slightly higher in O3 (P = 0.02). The treatment × week interaction was significant (P < 0.05) for fat yield and content, with differences (P < 0.01) only in the 3rd week of the data collection period in favor of group C (1.39 vs. 1.13 kg·day-1 and 3.86% vs. 3.23% for fat yield and content, respectively). Total DMI and PMR were similar (P > 0.05) between treatments. Concentrate intake was higher (P < 0.01) in C compared with O3. Pasture DMI tended (P = 0.06) to be greater for cows that received the O3 treatment compared with C. Total metabolizable energy (ME) intake was similar (P = 0.44) between treatments. No treatment effect was detected (P > 0.05) in rumen environment parameters. Supplementation with Ca-FA reduced (P < 0.05) the hypercholesterolemic fraction of milk (C12:0, C14:0 and C16:0, -13.6%, -7.4% and -9.0%, respectively). The concentration of α-linolenic acid (C18:3n-3) increased (108%, P < 0.01) in O3 group compared with group C. The absence of negative effects of lipids on the fat content of milk and ruminal fermentation suggests that protection by saponification was effective. The supplementation with Ca-FA (0.85 kg·day-1) improved the healthy value of the milk.

Alternative wood treatment with blends of linseed oil,alcohols and pyrolysis oil

Linseed oil is a common wood treatment agent,which is often blended with naphthenic oil during its application.In this study,we developed new types of linseed oil blends,where the naphthenic oil was substituted with alcohols and pyrolysis oil.As miscibility tests revealed,linseed oil can be blended indefinitely with primary alcohols containing three carbon atoms or more.In addition,kinetic stability of three-component-mixtures was found,which comprised linseed oil,alcohol and pyrolysis oil.The developed blends were further tested for their viscosity and rate of solvent evaporation.At last,trial impregnations of wood were done to test this new treatment agent.The uptake of treatment oil and the effect on water repellency varied,and substituting white spirit with propanol and pyrolysis oil showed potential.The latter were miscible with 50%(wt)linseed oil at concentrations of 37.5%1-or 2-propanol and 12.5%pyrolysis oil.Compared with the reference case,treatment with this agent markedly decreased the water-uptake of the wood.Our study hence attributes great potential to the newly developed linseed oil blends,which may introduce additional product characteristics and generate value to byproducts via pyrolysis.

A Lyophilized Water Extract of Melissa officinalis L. as an Effective Natural Antioxidant during the Storage of Dry Fermented Sausages High in a-Linolenic Acid and DHA

A pre-emulsified mixture of linseed and algae oils （15/10） and stabilized with 686 ppm of a lyophilized water extract of Melissa officinalis, was successfully applied in dry fermented sausages to increase the ω-3 PUFA content. The objective of this work was to evaluate the stability of this modified formulation during the storage and to compare it to that of a traditional formulation. Traditional and modified products were stored during 90 days at 4 °C in aerobic conditions. Fatty acid profiles, TBARS and volatile compounds derived from oxidation were analyzed at 0, 30 and 90 days of storage. The fatty acid profiles did not significantly change along the storage period. The stabilizing effect of the natural antioxidants ofM. officinalis could contribute to detect no losses of to-3 PUFA in Modified （30 days： 2.13 g/100 g of product, 90 days： 2.33 g/100 g of product）, whereas in Control products a slightly significant reduction was detected （30 days： 0.34 g/100 g of product, 90 days： 0.29 g/! 00 g of product）. After 90 days, the increases of TBARS and hexanal content were much higher in Control than in Modified （Control： 1.41 mg MDA/kg ＆ 17,915 ng dodecane/kg of dry matter; Modified： 0.48 mg MDA/kg ＆ 2,496 ng dodecane/kg of dry matter）. In conclusion, the lyophilized water extract of M. officinalis protected high ωo-3 PUFA of dry fermented sausages from oxidation along the storage time, guaranteeing the nutritional improvements achieved with the modified formulation.

Modeling and optimization of the parameters affecting the in-situ microencapsulation process for producing epoxy-based self-healing anti-corrosion coatings

Micro/nanocapsules of urea-formaldehyde resin loaded with linseed oil, which are a self-healing agent in glass flake epoxy anti-corrosion paint, were prepared using a combination of ultrasonic homogenization and in-situ polymerization. The main objective of this study was to model and optimize the microen- capsulation process. Five-level central composite design was used to design, model, and optimize the microencapsulation process. A quadratic model was constructed to show the dependency of the per- centage of encapsulated linseed oil and capsule size, as model responses, on the studied independent variables （the rotational speed of the agitator and the power and duration of sonication）. Analysis of vari- ance showed that all of the variables have significant effects on the encapsulated linseed oil percentage, while the rotational speed of the agitator and sonication time is effective variables for controlling the capsule size. Under the determined optimum conditions, a maximum encapsulated linseed oil percentage （ELO%） of 93.9% and a minimum micro/nanocapsule size of 0.574 μm were achieved at 594 rpm agitation, 350 W sonication power, and 3 min sonication time. Validation of the model was performed. The percent- age relative errors between the predicted and experimental values of the ELO% and micro/nanocapsule size are 1.28% and 3.66%, respectively. The efficacy of the optimum micro/nanocapsules in healing cracks in a glass flake epoxy paint and corrosion protection was investigated by the salt spray test and Tafel polarization technique.