Electrolytic enrichment method for tritium determination in the Arctic Ocean using liquid scintillation counter

A method of measuring the tritium in seawater based on electrolytic enrichment and ultra-low background liquid scintillation counting techniques was established.The different factors influencing the detection limit were studied,including the counting time,the electrolytic volume of the seawater samples,the selection of background water,scintillation solution and their ratio.After optimizing the parameters and electrolyzing 350 mL volume of samples,the detection limit of the method was as low as 0.10 Bq/L.In order to test the optimization of system for this method,of the 84 seawater samples collected from the Arctic Ocean we measured,92%were above the detection limit(the activity of this samples ranged from 0.10 Bq/L to 1.44 Bq/L with an average of(0.30±0.24)Bq/L).In future research,if we need to accurately measure the tritium activity in samples,the volume of the electrolytic samples will be increased to further reduce the minimum detectable activity.

FPGA implementation of 500-MHz high-count-rate high-time-resolution real-time digital neutron-gamma discrimination for fast liquid detectors

Fast neutron flux measurements with high count rates and high time resolution have important applications in equipment such as tokamaks.In this study,real-time neutron and gamma discrimination was implemented on a self-developed 500-Msps,12-bit digitizer,and the neutron and gamma spectra were calculated directly on an FPGA.A fast neutron flux measurement system with BC-501A and EJ-309 liquid scintillator detectors was developed and a fast neutron measurement experiment was successfully performed on the HL-2 M tokamak at the Southwestern Institute of Physics,China.The experimental results demonstrated that the system obtained the neutron and gamma spectra with a time accuracy of 1 ms.At count rates of up to 1 Mcps,the figure of merit was greater than 1.05 for energies between 50 keV and 2.8 MeV.

Event vertex and time reconstruction in large-volume liquid scintillator detectors

Large-volume liquid scintillator detectors with ultra-low background levels have been widely used to study neutrino physics and search for dark matter.Event vertex and event time are not only useful for event selection but also essential for the reconstruction of event energy.In this study,four event vertex and event time reconstruction algorithms using charge and time information collected by photomultiplier tubes were analyzed comprehensively.The effects of photomultiplier tube properties were also investigated.The results indicate that the transit time spread is the main effect degrading the vertex reconstruction,while the effect of dark noise is limited.In addition,when the event is close to the detector boundary,the charge information provides better performance for vertex reconstruction than the time information.

Calibration and Unfolding of the Pulse Height Spectra of Liquid Scintillator-Based Neutron Detectors Using Photon Sources

An accurate energy calibration of a 5＂× 2＂ BC501A liquid scintillator-based neutron detector by means of photon sources and the unfolding of pulse height spectra are described. The photon responses were measured with 22Na, 137Cs and 54Mn photon sources and simulated using the GRESP code, which was developed at the Physiknlisch Technische Bundesanstalt in Germany. Pulse height spectra produced by three different photon sources were employed to investigate the effects of the unfolding techniques. It was found that the four unfolding codes of the HEPRO and UMG3.3 packages, including GRAVEL, UNFANA, MIEKE and MAXED, performed well with the test spectra and produced generally consistent results. They could therefore be used to obtain neutron energy spectra in toknmak experiments.

Improvement of machine learning-based vertex reconstruction for large liquid scintillator detectors with multiple types of PMTs

The precise vertex reconstruction for large liquid scintillator detectors is essential.A novel machine learning-based method was successfully developed to reconstruct an event vertex in JUNO.In this study,the performance of machine learning-based vertex reconstruction was further improved by optimizing the input images of neural networks.By separating the information of different types of PMTs and adding the information of the second hit of PMTs,the vertex resolution was improved by approximately 9.4% at 1 MeV and 9.8% at 11 MeV.

Data-driven simultaneous vertex and energy reconstruction for large liquid scintillator detectors

High-precision vertex and energy reconstruction are crucial for large liquid scintillator detectors such as that at the Jiangmen Underground Neutrino Observatory(JUNO),especially for the determination of neutrino mass ordering by analyzing the energy spectrum of reactor neutrinos.This paper presents a data-driven method to obtain a more realistic and accurate expected PMT response of positron events in JUNO and develops a simultaneous vertex and energy reconstruction method that combines the charge and time information of PMTs.For the JUNO detector,the impact of the vertex inaccuracy on the energy resolution is approximately 0.6%.

Research and Development of Gadolinium Loaded Liquid Scintillator for Daya Bay Neutrino Experiment

Daya Bay reactor anti-neutrino experiment is designed to measure an important parameter, θ13, of neutrino by using anti-neutrino created by Daya Bay and Ling Ao nuclear power plants. The experiment need 200 tonnes gadolinium loaded liquid scintillator (Gd-LS) as target. The purpose of this research is to develop suitable Gd-LS candidates for this experiment, which should have long attenuation length, high light yield, long term stability, and should be compatible with the material used to build the containers. Two kinds of Gd-LS were developed using carboxylic acids 2-ethylhexanoic acid (EHA) and 3, 5, 5-trimethylhexanoic acid (TMHA) as complexing ligands and mesitylene and linear alkyl benzene (LAB) as scintillator solvents. Four Gd-LS samples with different Gd content and complexing ligands were prepared and characterized. The relative light yields and the stabilities of all samples are satisfying, and the values of attenuation length show that TMHA is a better ligand than EHA.

A LN2-based cooling system for a next-generation liquid xenon dark matter detector

In recent years, cooling technology for liquid xenon(LXe) detectors has advanced driven by the development of dark matter(DM) detectors with target mass in the 100–1000 kg range. The next generation of DM detectors based on LXe will be in the 50,000 kg(50 t)range requiring more than 1 k W of cooling power. Most of the prior cooling methods become impractical at this level.For cooling a 50 t scale LXe detector, a method is proposed in which liquid nitrogen(LN2) in a small local reservoir cools the xenon gas via a cold finger. The cold finger incorporates a heating unit to provide temperature regulation. The proposed cooling method is simple, reliable, and suitable for the required long-term operation for a rare event search. The device can be easily integrated into present cooling systems, for example the ‘‘Cooling Bus’ ’employed for the Panda X I and II experiments. It is still possible to cool indirectly with no part of the cooling or temperature control system getting in direct contact with the clean xenon in the detector. Also, the cooling device can be mounted at a large distance, i.e., the detector is cooled remotely from a distance of 5–10 m. The method was tested in a laboratory setup at Columbia University to carry out different measurements with a small LXe detector and behaved exactly as predicted.

Unambiguously Resolving the Potential Neutrino Magnetic Moment Signal at Large Liquid Scintillator Detectors

Non-vanishing electromagnetic properties of neutrinos have been predicted by many theories beyond the Standard Model, and an enhanced neutrino magnetic moment can have profound implications for fundamental physics. The XENON1T experiment recently detected an excess of electron recoil events in the 1–7 keV energy range, which can be compatible with solar neutrino magnetic moment interaction at a most probable value of μ_(v) = 2.1 × 10^(-11)μ_(B).However, tritium backgrounds or solar axion interaction in this energy window are equally plausible causes.Upcoming multi-tonne noble liquid detectors will test these scenarios more in depth, but will continue to face similar ambiguity. We report a unique capability of future large liquid scintillator detectors to help resolve the potential neutrino magnetic moment scenario. With O(100) kton·year exposure of liquid scintillator to solar neutrinos, a sensitivity of μ_(v) < 10^(-11)μ_(B) can be reached at an energy threshold greater than 40 keV, where no tritium or solar axion events but only neutrino magnetic moment signal is still present.

Unfolding the fast neutron spectra of a BC501A liquid scintillation detector using GRAVEL method

Accurate knowledge of the neutron energy spectra is useful in basic research and applications. The overall procedure of measuring and unfolding the fast neutron energy spectra with BC501 A liquid scintillation detector is described. The recoil proton spectrum of 241Am-Be neutrons was obtained experimentally. With the NRESP7 code, the response matrix of detector was simulated.Combining the recoil proton spectrum and response matrix, the unfolding of neutron spectra was performed by GRAVEL iterative algorithm. A MatLab program based on the GRAVEL method was developed. The continuous neutron spectrum of 241Am-Be source and monoenergetic neutron spectrum of D-T source have been unfolded successfully and are in good agreement with their standard reference spectra. The unfolded 241Am-Be spectrum are more accurate than the spectra unfolded by artificial neural networks in recent years.

Study of absorption and re-emission processes in a ternary liquid scintillation system

Liquid scintillators are widely used as the neutrino target in neutrino experiments.The absorption and emission of different components of a ternary liquid scintillator （Linear Alkyl Benzene （LAB） as the solvent,2,5-diphenyloxazole （PPO） as the fluor and p-bis-（o-methylstyryl）-benzene （bis-MSB） as wavelength shifter） are studied.It is shown that the absorption of this liquid scintillator is dominant by LAB and PPO at wavelengths less than 349 nm,and the absorption by bis-MSB becomes prevalent at the wavelength larger than 349 nm.The fluorescence quantum yields,which are the key parameters to model the absorption and re-emission processes in large liquid scintillation detectors,are measured.

Study of n-γ discrimination for 0.4-1 MeV neutrons using the zero-crossing method with a BC501A liquid scintillation detector

An experimental system aimed at n-γ discrimination using the zero-crossing method with a φ3’’×2’’ BC501A liquid scintillation detector was established and tested with an Am-Be neutron source. Two-dimensional plots of energy versus zero-crossing time were obtained. The quality of n-γ discrimination was checked by the figure-of-merit （FOM）, the neutron peak-to-valley ratio, and the proportion of leaked neutrons over all neutron events. The performance of n-γ discrimination in terms of FOM was compared with previous work done by other groups. The n-γ discrimination in four different energy regions with an interval of 0.1 MeV between 0.3 MeV and 0.7 MeV was studied, and the results indicate that the n-γ discrimination threshold can go down to 0.4 MeV.

Simulation of large-scale fast neutron liquid scintillation detector

Neutron background measurement is always very important for dark matter detection due to almost the same effect for the recoiled nucleus scattered off by the incident neutron and dark matter particle. For deep under-ground experiments, the flux of neutron background is so low that large-scale detection is usually necessary. In this paper, by using Geant4, the relationship between detection efficiency and volume is investigated, meanwhile, two geometrical schemes for this detection including a single large-sized detector and arrayed multi-detector are compared under the condition of the same volume. The geometrical parameters of detectors are filtrated and detection efficiencies obtained under the similar background condition of China Jingping Underground Laboratory （CJPL）. The results show that for a large-scale Gd-doped liquid scintillation detector, the detection efficiency increases with the size of detector at the beginning and then trends toward a constant. Under the condition of the same length and cross section, the arrayed multi-detector has almost similar detection performance as the single large-sized detector, while too much detector number could cause degeneration of detection performance. Considering engineering factors, such as testing, assembling and production, the 4 × 4 arrayed detector scheme is flexible and more suitable. Furthermore, the conditions for using fast and slow signal coincidence detection and the detectable lower limit of neutron energy are evaluated by simulating the light process.

Digital pulse shape discrimination methods for n-γ separation in an EJ-301 liquid scintillation detector

A digital pulse shape discrimination system based on a programmable module NI-5772 has been established and tested with an EJ-301 liquid scintillation detector. The module was operated by running programs developed in Lab VIEW, with a sampling frequency up to 1.6 GS/s. Standard gamma sources ^22 Na,^137Cs and ^60 Co were used to calibrate the EJ-301 liquid scintillation detector, and the gamma response function was obtained. Digital algorithms for the charge comparison method and zero-crossing method have been developed. The experimental results show that both digital signal processing（DSP） algorithms can discriminate neutrons from γ-rays. Moreover,the zero-crossing method shows better n-γ discrimination at 80 ke Vee and lower, whereas the charge comparison method gives better results at higher thresholds. In addition, the figure-of-merit（FOM） for detectors of two different dimensions were extracted at 9 energy thresholds, and it was found that the smaller detector presented better n-γseparation for fission neutrons.

Standardization of Tritium Water by TDCR Method

The triple-to-double coincidence ratio （TDCR） method of liquid scintillation count- ing is an absolute measurement method of radioactivity. The formulation of the TDCR method and the established TDCR liquid scintillation counter are presented in this paper. The NIST standard reference material （SRM） of tritium water was measured to verify the performance of the TDCR liquid scintillation counter.

Study of n-γ discrimination in low energy range(above 40 keVee) by charge comparison method with a BC501A liquid scintillation detector

A VME-based experiment system for n-y discrimination using the charge comparison method was established.A data acquisition program for controlling the programmable modules and processing data online via VME64X bus was developed through the use of Lab VIEW.The two-dimensional（2D） scatter plots of the charge in the slow component vs.the total charge from ^（241）Am-Be and 252Cf neutron sources are presented.The 2D scatter plots of the energy vs.the ratio of the charge in the slow component to the total charge of the pulses are also presented.The quality of n-γ discrimination was checked by the figure-of-merit,and the results showed good performance of n-γ discrimination at the low energy range.Neutrons and γ-rays were separated above 50 keVee（electron-equivalent energy）.The quality of n-γ discrimination has been improved compared with others＇ results at five energies（150,250,350,450,550 keVee）.

Low-radioactivity ultrasonic hydrophone used in positioning system for Jiangmen Underground Neutrino Observatory

To satisfy the accurate positioning requirement of the calibration source in the Jiangmen Underground Neutrino Observatory, a Tonpilz-type hydrophone with low radioactivity and high electroacoustics is developed.The radioactivity of the proposed hydrophone is strictly controlled by selecting pure raw materials, especially active piezoelectric ceramics. The electroacoustic performance of the hydrophone is improved by making structural optimization. High sensitivity and aimed directivity are achieved using 33-mode piezoelectric ceramic rings arranged in series and improvement in the radiating head of the Tonpilz hydrophone, respectively. All electroacoustic performances are studied through finite element analyses.The simulations indicate that the electroacoustic performances of the hydrophones in linear alkylbenzene-based liquid scintillator can be approximately predicted according to the results in water because their differences caused by two types of acoustic media, water and liquid scintillator, are known. The tests show that the hydrophone prototype can achieve a maximum sensitivity of-209.3dB and a beamwidth of 132.2° at a frequency of 143 kHz.In addition, eight hydrophones only contributed to a background radioactivity level of 26 ± 4 mHz in the neutrino analysis.

Discrimination of pp solar neutrinos and^(14)C double pile-up events in a large-scale LS detector

As a unique probe,the precision measurement of pp solar neutrinos is important for studying the sun’s energy mechanism as it enables monitoring the thermodynamic equilibrium and studying neutrino oscillations in the vacuum-dominated region.For a large-scale liquid scintillator detector,a bottleneck for pp solar neutrino detection is the pile-up events of intrinsic14C decay.This paper presents a few approaches to discriminating between pp solar neutrinos and ^(14)C pile-up events by considering the differences in their time and spatial distributions.In this study,a Geant4-based Monte Carlo simulation is conducted.Multivariate analysis and deep learning technology are adopted to investigate the capability of ^(14)C pile-up reduction.The BDTG (boosted decision trees with gradient boosting) model and VGG network demonstrate good performance in discriminating pp solar neutrinos and ^(14)C double pile-up events.Under the ^(14)C concentration assumption of 5×10-18g/g,the signal significance can achieve 10.3 and 15.6 using the statistics of only one day.In this case,the signal efficiency for discrimination using the BDTG model while rejecting 99.18% ^(14)C double pile-up events is 51.1%,and that for the case where the VGG network is used while rejecting 99.81%of the ^(14)C double pile-up events is 42.7%.

^(222)Rn calibration procedure for water analyses by liquid scintillation counting

Purpose Among the several methods to measure ^(222)Rn in water,the liquid scintillation counting(LSC)technique is one of the most sensitive and widely used when analysing non-saline waters by liquid extraction,providing excellent accuracy,precision and low-level detection limits.When using the liquid scintillation counter Tri-Carb 3170 TR/SL(Perkin-Elmer)it is not possible to make an automatic determination of the alpha/beta discrimination parameter,being necessary to evaluate the pulse decay discriminator(PDD)value manually to the ^(222)Rn determination.In this work,we describe the steps to perform the calibration of that type of equipment.Methods The method consists in the preparation of standard samples from a ^(226)Ra certified standard solution and the adjustment of the PDD value by hand until the percentage of alpha events reaches a plateau of a near-constant fraction of total events.The process consists in taking several measures between PDD 80 and 200 with 15 min counting time each.Within the plateau,the alpha/beta ratio was used to determine the plateau final range as well as the optimum PDD value.After that,the calibration standards and blanks were measured and the region of interest(ROI)was established by finding the maximum value for the figure of merit(FOM)in the upper and lower limits.Results The optimal PDD value of 148 was established by the alpha/beta ratio,and after that,it was possible to measure ^(226)Ra standards to perform the calibration.An efficiency of(9.758±0.035)×1^(0-1) was obtained.In routine measurements,a detection limit of about 0.50 Bq L^(-1) is achieved for a 120 min counting time.To evaluate the uncertainty budget,the uncertainties of the net count rate,the efficiency,the sample amount and the decay correction factor were considered.Conclusions A method was developed for the calibration of LSC Tri-Carb 3170 TR/SL with the optimization of the PDD using a ^(226)Ra standard solution.The acquisition to obtain the plot of the variation of the events fraction in each window(alpha and beta)in function of PDD allowed to evaluate a plateau where the fraction of events was at a minimum.Afterwards,it was possible to measure the set of ^(226)Ra standards after the equilibrium with ^(222)Rn and determine the efficiency for ^(222)Rn with a detection limit of about 0.50 Bq L^(-1) in routine analyses.

A comparison of two methods used for determination of tritium concentration in urine samples by liquid scintillation counter

Background Tritium(3H)emits low-energy beta particles with a maximum energy of 18.6 keV.Liquid scintillation counting technique(LSC)is mostly used for the detection and quantification of low-energy emitters like H-3.The most widely used method to determine the level of tritium in humans is testing urine.Method In this study,tritium activity concentrations in urine samples taken from 20 adults were measured.Their ages range from 23 to 50.Eight of them are female,and others are male.The tritium activity concentrations in urine samples were determined with two different methods.Also,two standard samples were used to compare urine samples.Result The efficiency values were found with two different methods(26.07%for the first method and 26.14%for the second method).According to the comparison results,the tritium concentration differences between these methods were found in a negligible level for urine samples and in an acceptable level for standard samples.Conclusion The tritium activity concentrations in urine and standard samples were calculated using two different methods.According to the comparison results,these two methods can be used for determination of tritium concentrations in urine samples.