Enhanced structural damage behavior of liquid-filled tank by reactive material projectile impact

A series of ballistic experiments were performed to investigate the damage behavior of high velocity reactive material projectiles(RMPs) impacting liquid-filled tanks,and the corresponding hydrodynamic ram(HRAM) was studied in detail.PTFE/Al/W RMPs with steel-like and aluminum-like densities were prepared by a pressing/sintering process.The projectiles impacted a liquid-filled steel tank with front aluminum panel at approximately 1250 m/s.The corresponding cavity evolution characteristics and HRAM pressure were recorded by high-speed camera and pressure acquisition system,and further compared to those of steel and aluminum projectiles.Significantly different from the conical cavity formed by the inert metal projectile,the cavity formed by the RMP appeared as an ellipsoid with a conical front.The RMPs were demonstrated to enhance the radial growth velocity of cavity,the global HRAM pressure amplitude and the front panel damage,indicating the enhanced HRAM and structural damage behavior.Furthermore,combining the impact-induced fragmentation and deflagration characteristics,the cavity evolution of RMPs under the combined effect of kinetic energy impact and chemical energy release was analyzed.The mechanism of enhanced HRAM pressure induced by the RMPs was further revealed based on the theoretical model of the initial impact wave and the impulse analysis.Finally,the linear correlation between the deformation-thickness ratio and the non-dimensional impulse for the front panel was obtained and analyzed.It was determined that the enhanced near-field impulse induced by the RMPs was the dominant reason for the enhanced structural damage behavior.

Attitude maneuver of liquid-filled spacecraft with a flexible appendage by momentum wheel

Attitude maneuver of liquid-filled spacecraft with an appendage as a cantilever beam by momentum wheel is studied. The dynamic equations are derived by conserva- tion of angular momentum and force equilibrium principle. A feedback control strategy of the momentum wheel is ap- plied for the attitude maneuver. The residual nutation of the spacecraft in maneuver process changes with some chosen parameters, such as steady state time, locations of the liq- uid container and the appendage, and appendage parame- ters. The results indicate that locations in the second and fourth quadrants of the body-fixed coordinate system and the second quadrant of the wall of the main body are better choices for.placing the liquid containers and the appendage than other locations if they can be placed randomly. Higher density and thicker cross section are better for lowering the residual nutation if they can be changed. Light appendage can be modeled as a rigid body, which results in a larger residual nutation than a flexible model though. The resid- ual nutation decreases with increasing absolute value of the initial sloshing angular height.

Growth model of cavity generated by the projectile impacting liquid-filled tank

The high-speed impact of a projectile on a liquid-filled tank causes the hydraulic ram,in which a cavity is formed.To study the growth characteristics of the cavity,the formation mechanism of the cavity is analyzed.The effect of Reynolds number and Mach number on drag coefficient is considered,the axial and radial growth models of the cavity are established respectively.The relative errors between the cavity length calculated by the axial growth model,the cavity diameter calculated by the radial growth model and Ma L.Y.test results are less than 20%,which verifies the effectiveness of the axial and radial growth models.Finally,numerical simulation is carried out to study the growth characteristics of the cavity caused by the projectile impacting the satellite tank at the velocity of 4000 m/s.The cavity length and diameter calculated by the axial and radial growth models agree well with those obtained by simulation results,indicating that the cavity length and diameter in satellite tank can be accurately calculated by the axial and radial growth models.

Laboratory-scale investigation of response characteristics of liquid-filled rock joints with different joint inclinations under dynamic loading

In underground rock engineering,water-bearing faults may be subjected to dynamic loading,resulting in the coupling of hydraulic and dynamic hazards.Understanding the interaction mechanism between the stress waves induced by dynamic loadings and liquid-filled rock joints is therefore crucial.In this study,an auxiliary device for simulating the liquid-filled layer was developed to analyze the dynamic response characteristics of liquid-filled rock joints in laboratory.Granite and polymethyl methacrylate(PMMA)specimens were chosen for testing,and high-amplitude shock waves induced by a split Hopkinson pressure bar(SHPB)were used to produce dynamic loadings.Impact loading tests were conducted on liquid-filled rock joints with different joint inclinations.The energy propagation coefficient and peak liquid pressure were proposed to investigate the energy propagation and attenuation of waves propagating across the joints,as well as the dynamic response characteristics of the liquid in the liquid-filled rock joints.For the inclination angle range considered herein,the experimental results showed that the energy propagation coefficient gently diminished with increasing joint inclination,and smaller coefficient values were obtained for granite specimens compared with PMMA specimens.The peak liquid pressure exhibited a gradually decreasing trend with increasing joint inclination,and the peak pressure for granite specimens was slightly higher than that for PMMA specimens.Overall,this paper may provide a considerably better method for studying liquid-filled rock joints at the laboratory scale,and serves as a guide for interpreting the underlying mechanisms for interactions between stress waves and liquid-filled rock joints.

Coupling dynamic analysis of a liquid-filled spherical container subject to arbitrary excitation

Using spherical coordinates, the coupling nonlinear dynamic system of a liquid-filled spherical tank, which can be excited discretionarily, is deduced by the H-O varia- tional principle, and the viscous damping is introduced via the liquid dissipation function. The kinetic equations of the coupling system are deduced by the relationship between the velocity of liquid particles and the disturbed liquid surface equation. Normal differential equations are obtained through the Galerkin method. An equivalent mechanical model is developed for liquid sloshing in a spherical tank subject to arbitrary excitation. The fixed and slosh masses, as well as the spring and damping constants, are determined in such a way as to satisfy the principle of equivalence. Numerical simulations illustrate the theoretical results in this paper as well.

Dynamic response of liquid-filled rectangular tank with elastic appendages under pitching excitation

Nonlinear dynamics of liquid-filled rectangular tank with elastic appendages are studied. Based on the assumption of ideal fluid, the coupling dynamic equations of rigid tank, elastic appendages and liquid fuel are derived using H-O principle. In the case of pitch excitation, the modified potential function and wave height function are introduced to describe the moving boundary of fluid, then Galerkin＇s method is used to discretize the dynamic equations into ordinary differential equations. The natural frequencics of the coupling system are formulated in liquid depth, the length of the tank, etc. The formulae are confirmed by numerical simulations, which also show that the effects of liquid and elastic appendages on the attitude angular of rigid.

EXPERIMENTAL INVESTIGATION AND COMPUTER SIMULATION ON DYNAMIC BUCKLING BEHAVIOR OF LIQUID-FILLED CYLINDRICAL SHELLS UNDER AXIAL IMPACT

This article reports an experimental investigation on the axial impact buckling of thin metallic cylindrical shells fully filled with water. Low velocity impact tests are carried out by DHR-9401 drop hammer rig. The whole process of dynamic buckling is simulated using LS-DYNA computer code. The consistency between experimental observation and numerical simulation is quite satisfactory. The investigation indicates that quite high internal hydrodynamic pressure occurs inside the shell during the impact process. Under the combined action of the high internal pressure and axial compression plastic buckling occurs easily in the thin-walled shells and buckling modes take on regular and axisymmetric wrinkles.

Improved frequency modeling and solution for parallel liquid-filled pipes considering both fluid-structure interaction and structural coupling

The dynamic characteristics of a single liquid-filled pipe have been broadly studied in the previous literature.The parallel liquid-filled pipe(PLFP)system is also widely used in engineering,and its structure is more complex than that of a single pipe.However,there are few reports about the dynamic characteristics of the PLFPs.Therefore,this paper proposes improved frequency modeling and solution for the PLFPs,involving the logical alignment principle and coupled matrix processing.The established model incorporates both the fluid-structure interaction(FSI)and the structural coupling of the PLFPs.The validity of the established model is verified by modal experiments.The effects of some unique parameters on the dynamic characteristics of the PLFPs are discussed.This work provides a feasible method for solving the FSI of multiple pipes in parallel and potential theoretical guidance for the dynamic analysis of the PLFPs in engineering.

Study on liquid-filled structure target with shaped charge vertical penetration

Based on the characteristic expanded hole of a shaped charge jet(SCJ) for target penetration and the reflow characteristics of liquids,the liquid-filled structure of a target disturbs the stability of the SCJ acquired in two independent parts.The interference jet speed interval,the escape jet speed interval,and the surplus depth are calculated on the basis of the virtual origin theory.The experimental results,including the velocity of the escaped jet tip and the surplus depth of penetration,are consistent with the theoretical results.Experiments show that the theory can describe the interaction process of the target with a shaped charge jet.

Parameter design of a liquid-filled sloshing system

The nonlinear governing equations of the liquid sloshing modals in a cylindrical storage tank are established. Through analytical analysis, the analytical expressions of the solutions of this kind of system are obtained. With different parameters, the dynamical behaviors of the solutions are different from the trivial ones. To prevent system instability, two selection principles that the stiffness equations are positive-definite and the nonlinear terms of the system are not regenerative elements are given. Meanwhile, numerical simulations are also given, which confirm the analytical results.

Axial power flow distributions of ultrasonic guided waves in viscous liquid-filled pipes

The axial power flow (APF) magnitude and attenuation distributions of ultrasonic longitudinal guided waves in viscous liquid-filled elastic pipes are investigated. The optimal location, optimal mode and its frequency-thickness product (fd) for the test of pipes filled with viscous liquid are chosen according to APF and attenuation distributions. The results show that the APF magnitude distribution is an important parameter in choosing the modes and parameters. A particular mode has weak dispersion in ranges of fd values with large group velocity, while other modes with smaller group velocity in the same fd ranges have stronger dispersion. It has been observed that, within these ranges, the chosen mode has a larger APF on the (pipe’s) wall. Therefore, in the region of fd values where a particular mode has a large group velocity, this mode will be effective to be used in testing elastic pipes filled with viscous liquid. The results obtained from both the APF analysis and attenuation distribution are consistent.

A dark hollow beam from a selectively liquid-filled photonic crystal fibre

This paper reports that, based on the electromagnetic scattering theory of the multipole method, a high-quality hollow beam is produced through a selectively liquid-filled photonic crystal fibre. Instead of a doughnut shape, a typical hollow beam is produced by other methods; the mode-field images of the hollow-beam photonic crystal fibre satisfy sixth-order rotation symmetry, according to the symmetry of the photonic crystal fibre （PCF） structure. A dark spot size of the liquid-filled photonic crystal fibre-generated hollow beam can be tuned by inserting liquid into the cladding region and varying the photonic crystal fibre structure parameters. The liquid-filled PCF makes a convenient and flexible tool for the guiding and trapping of atoms and the creation of all-fibre optical tweezers.

Nonlinear dynamic model and control of three-axis stabilized liquid-filled spacecraft attitude system

The fuel slosh in the storage tanks affects the attitude dynamics of the liquid-filled spacecraft during orbit transferring. To describe the interactions between the fuel slosh dynamics and the spacecraft attitude dynamics, a novel nonlinear dynamic model for three-axis liquid-filled spacecraft is presented, and in this paper, the multi-body dynamics method is utilized. In this model, the fuel slosh is represented by the motions of an equivalent sphere pendulum, and the fuel slosh is underactuated. The proposed dynamics model meets the demand of attitude controller design of liquid-filled spacecraft. Then, a nonlinear proportional-plus-derivative (PD) type controller is designed for the proposed model based on the Lyapunov direct approach. This controller can suppress the fuel slosh and stabilize the attitude of the liquid-filled spacecraft. Numerical simulations are presented to verify the effectiveness of the proposed nonlinear dynamic model and the designed underactuated controller when compared with the conventional control scheme.

Research on Leak Location of Liquid-filled Pipe Based on Frequency Dispersion Characteristics

Due to the material problems and force majeure factors,the leakage will be occurred on the liquid-filled pipe resulting in waste of resources,environmental pollution and even endangering safety.Acoustic wave detection technology is widely used in buried pipeline leak detection,this technology mainly uses the wave(n=0,s=1)in the pipeline acoustic wave to locate the leak.When the leakage acoustic signal propagates along the liquid-filled pipe,the frequency dispersion characteristics can be obtained by wavelet decomposition.And there is a time delay(time difference)value between the leaky acoustic signals collected by the sensors at both ends of the leak.The outputs show that the results obtained by wavelet decomposition are in good agreement with the theoretical calculation results.Based on the obtained dispersion relation,the time delay values at different characteristic frequencies are analyzed by the cross-correlation method,and the leak location accuracy is discussed.This research content provides theoretical support and engineering application guidance for pipe leakage location technology.

Dynamic Modeling and Simulation of Multi-body Systems Using the Udwadia-Kalaba Theory

Laboratory experiments were conducted for falling U-chain,but explicit analytic form of the general equations of motion was not presented.Several modeling methods were developed for fish robots,however they just focused on the whole fish’s locomotion which does little favor to understand the detailed swimming behavior of fish.Udwadia-Kalaba theory is used to model these two multi-body systems and obtain explicit analytic equations of motion.For falling U-chain,the mass matrix is non-singular.Second-order constraints are used to get the constraint force and equations of motion and the numerical simulation is conducted.Simulation results show that the chain tip falls faster than the freely falling body.For fish robot,two-joint Carangiform fish robot is focused on.Quasi-steady wing theory is used to approximately calculate fluid lift force acting on the caudal fin.Based on the obtained explicit analytic equations of motion(the mass matrix is singular),propulsive characteristics of each part of the fish robot are obtained.Through these two cases of U chain and fish robot,how to use Udwadia-Kalaba equation to obtain the dynamical model is shown and the modeling methodology for multi-body systems is presented.It is also shown that Udwadia-Kalaba theory is applicable to systems whether or not their mass matrices are singular.In the whole process of applying Udwadia-Kalaba equation,Lagrangian multipliers and quasi-coordinates are not used.Udwadia-Kalaba theory is creatively applied to dynamical modeling of falling U-chain and fish robot problems and explicit analytic equations of motion are obtained.

New Method for Predicting the Motion Responses of A Flexible Joint Multi-Body Floating System to Irregular Waves

A new hybrid method of frequency domain and time domain is developed in this paper to predict the motion responses of a flexibly joint multi-body floating system to irregular waves. The main idea of the method is that the three-dimensional frequency method is used to obtain the hydrodynamic coefficients and the response equations are solved in time domain step by step. All the forces can be obtained at the same time. The motions and nonlinear mooring forces of a box type six-body floating system are predicted. A comparison of the theoretical method-based Solutions with experimental results has shown good agreement.

Analysis for the Deployment of Single-Point Mooring Buoy System Based on Multi-Body Dynamics Method

Deployment of buoy systems is one of the most important procedures for the operation of buoy system. In the present study, a single-point mooring buoy system which contains surface buoy, cable segments with components, anchor and so on is modeled by applying multi-body dynamics method. The motion equations are developed in discrete node description and fully Cartesian coordinates. Then numerical method is used to solve the ordinary differential equations and dynamics simulations are achieved while anchor is casting from board. The trajectories and velocities of different nodes without current and with current in buoy system are obtained. The transient tension force of each part of the cable is analyzed in the process of deployment. Numerical results indicate that the transient payload increases to a peak value when the anchor is touching the seabed and the maximum tension force will vary with different floating configuration. This work is helpful for design and deployment planning of buoy system.

MOTION TYPES AND CHAOS OF MULTI-BODY SYSTEMS VIBRATING WITH IMPACTS

In this paper,the limit sets theory for an autonomous dynamical system is generalized to a multi-body system vibrating with impacts.We discover that if every motion of the system is bounded,it has only four different types:periodic motion 7 t,non-periodic recurrent motion γ2,and non-Poisson stable mo- tions γ3 and γ4 approaching γ1 and γ2, respectively.γ2 is the source of chaos.It is very interesting that cha- otic motions seem stochastic but possess the character of recurrence.By way of example,we discuss chaotic motions of a small ball bouncing vertically on a massive vibrating table.The result obtained by us is different from that obtained by Holmes.

Multi-Body Dynamics Modeling and Simulation Analysis of a Vehicle Suspension Based on Graph Theory

Multi-body dynamics,relative coordinates and graph theory are combined to analyze the structure of a vehicle suspension.The dynamic equations of the left front suspension system are derived for modeling.First,The pure tire theory model is used as the input criteria of the suspension multibody system dynamic model in order to simulate the suspension K&C characteristics test.Then,it is important to verify the accuracy of this model by comparing and analyzing the experimental data and simulation results.The results show that the model has high precision and can predict the performance of the vehicle.It also provides a new solution for the vehicle dynamic modeling.

KEY TECHNIQUES OF MULTI-BODY MODELING OF OCCUPANT RESTRAINT SYSTEM OF VEHICLE SIDE IMPACT

Based on multi-body dynamics, the simulation models of auto-side structures and occupant＇s dynamic responses are set up, using the occupant injury simulation software MADYMO3D. These models include auto-body structure, impact barrier, seat and dummy. Definitions of multi-body and joints and dynamics properties of joints based on FE combination models, of model setup are introduced. Kelvin element of MADYMO is introduced to show the force action between non-adjoining rigid bodies, too. Then all examples of the methods mentioned are given. By the comparison of simulation and real test, the contract curves between simulation and real test for main structures and biology mechanics properties of dummy are obtained. The result shows the accuracy and validity of the models.