Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galva...Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galvanostatic charge /discharge and electrochemical impedance spectroscopy（EIS）. The XRD study shows that a small amount of Mn2＋-doped does not alter the structure of Li3V2（PO4）3/C materials, and all Mn2＋-doped samples are of pure single phase with a monoclinic structure （space group P21/n）. The XPS analysis indicates that valences state of V and Mn are ＋3 and ＋2 in Li3V1.94Mn0.09（PO4）3/C, respectively, and the citric acid in raw materials was decomposed into carbon during calcination, and residual carbon exists in Li3V1.94Mn0.09（PO4）/C. The results of electrochemical measurements show that Mn2＋-doping can improve the cyclic stability and rate performance of these cathode materials. The Li3V1.94Mn0.09（PO4）3/C cathode material shows the best cyclic stability and rate performance. For example, at the discharge current density of 40 mA/g, after 100 cycles, the discharge capacity of Li3V1.94Mn0.09（PO4）3/C declines from initial 158.8 mA·h/g to 120.5 mA·h/g with a capacity retention of 75.9%; however, that of the Mn-undoed sample declines from 164.2 mA·h/g to 72.6 mA·h/g with a capacity retention of 44.2%. When the discharge current is increased up to 1C, the intial discharge capacity of Li3V1.94Mn0.09（PO4）3/C still reaches 146.4 mA·h/g, and the discharge capacity maintains at 107.5 mA·h/g after 100 cycles. The EIS measurement indicates that Mn2＋-doping with a appropriate amount of Mn2＋ decreases the charge transfer resistance, which is favorable for the insertion/extraction of Li＋.展开更多
Y-doped Li3V2（PO4）3 cathode materials were prepared by a carbothermal reduction（CTR） process.The properties of the Y-doped Li3V2（PO4）3 were investigated by X-ray diffraction（XRD） and electrochemical measuremen...Y-doped Li3V2（PO4）3 cathode materials were prepared by a carbothermal reduction（CTR） process.The properties of the Y-doped Li3V2（PO4）3 were investigated by X-ray diffraction（XRD） and electrochemical measurements.XRD studies showed that the Y-doped Li3V2（PO4）3 had the same monoclinic structure as the undoped Li3V2（PO4）3.The Y-doped Li3V2（PO4）3 samples were investigated on the Li extraction/insertion performances through charge/discharge, cyclic voltammogram（CV）, and electrochemical impedance spectra（EIS）.The optimal doping content of Y was x=0.03 in Li3V2-xYx（PO4）3 system.The Y-doped Li3V2（PO4）3 samples showed a better cyclic ability.The electrode reaction reversibility was enhanced, and the charge transfer resistance was decreased through the Y-doping.The improved electrochemical perormances of the Y-doped Li3V2（PO4）3 cathode materials were attributed to the addition of Y3＋ ion by stabilizing the monoclinic structure.展开更多
Rational design of porous conductive hosts with high electrical conductivity,large surface area,and adequate interior space is desirable to suppressing dendritic lithium growth and accommodating large volume change of...Rational design of porous conductive hosts with high electrical conductivity,large surface area,and adequate interior space is desirable to suppressing dendritic lithium growth and accommodating large volume change of lithium metal anode during the Li plating/stripping process.However,due to the conductive nature of the conductive hosts,Li is easily deposited directly on the top of the hosts,which hinders it from fully functioning.To circumvent the issue,in this study,we designed a novel porous carbon host with a gradient-pore-size structure based on one-dimensional(1D)carbon with different diameters.With this kind of host,stable cycling with high and stable Coulombic efficiency of~98%is achieved at 0.5 mA cm^(−2) with an areal capacity of 1 mAh cm^(−2) over 320 cycles.In contrast,the normal three-dimensional(3D)carbon nanotube host presents a moss-like Li morphology with wildly fluctuating Coulombic efficiency after 100 cycles.The results reveal that the unique gradient-pore-size structure of the 3D conductive host greatly improves the performance of lithium metal batteries.展开更多
Spinel lithium manganese oxide ion-sieves have been considered the most promising adsorbents to extract Li^+ from brines and sea water.Here,we report a lithium ion-sieve which was successfully loaded onto tubular α-A...Spinel lithium manganese oxide ion-sieves have been considered the most promising adsorbents to extract Li^+ from brines and sea water.Here,we report a lithium ion-sieve which was successfully loaded onto tubular α-Al2 O3 ceramic substrates by dipping crystallization and post-calcination method.The lithium manganese oxide Li4 Mn5 O(12)was first synthesized onto tubular α-Al2 O3 ceramic substrates as the ion-sieve precursor(i.e.L-AA),and the corresponding lithium ion-sieve(i.e.H-AA) was obtained after acid pickling.The chemical and morphological properties of the ion-sieve were confirmed by X-ray diffraction(XRD) and scanning electron microscopy(SEM).Both L-AA and H-AA showed characteristic peaks of α-Al2 O3 and cubic phase Li4 Mn5 O(12) and the peaks representing cubic phase could still exist after pickling.The lithium manganese oxide Li4 Mn5 O(12) could be uniformly loaded not only on the surface of α-Al2 O3 ubstrates but also inside the pores.Moreover,we found that the equilibrium adsorption capacity of H-AA was 22.9 mg·g^-1.After 12 h adsorption,the adsorption balance was reached.After 5 cycles of adsorption,the adsorption capacity of H-AA was 60.88% of the initial adsorption capacity.The process of H-AA adsorption for Li^+correlated with pseudo-second order kinetic model and Langmuir model.Adsorption thermodynamic parameters regarding enthalpy(△N), Gibbs free energy(△G) and entropy(AS) were calculated.For the dynamic adsorptiondesorption process of H-AA,the H-AA exhibited excellent adsorption performance to Li^+ with the Li^+ dynamic adsorption capacity of 9.74 mg·g^-1 and the Mn^2+dissolution loss rate of 0.99%.After 3 dynamic adsorption-desorption cycles,80% of the initial dynamic adsorption capacity was still kept.展开更多
Cr-doped Li3V2（PO4）3 cathode materials Li3V2-xCr（PO4）3 were prepared by a carbothermal reduction（CTR） process. The properties of the Cr-doped Li3V2（PO4）3 were investigated by X-ray diffraction （XRD）, scannin...Cr-doped Li3V2（PO4）3 cathode materials Li3V2-xCr（PO4）3 were prepared by a carbothermal reduction（CTR） process. The properties of the Cr-doped Li3V2（PO4）3 were investigated by X-ray diffraction （XRD）, scanning electron microscopic （SEM）, and electrochemical measurements Results show that the Cr-doped Li3V2（PO4）3 has the same monoclinic structure as the undoped Li3V2（PO4）3, and the particle size of Cr-doped Li3V2（PO4）3 is smaller than that of the undoped Li3V2（PO4）3 and the smallest particle size is only about 1 1μm. The Cr-doped Li3V2（PO4）3 samples were investigated on the Li extraction/insertion performances through charge/discharge, cyclic voltammogram （CV）, and electrochemical impedance spectra（EIS）. The optimal doping content of Cr was that x=0.04 in the Li3V2-xCrx（PO4）3 samples to achieve high discharge capacity and good cyclic stability. The electrode reaction reversibility was enhanced, and the charge transfer resistance was decreased through the Cr-doping. The improved electrochemical performances of the Cr-doped Li3V2（PO4）3 cathode materials are attributed to the addition of Cr^3＋ ion by stabilizing the monoclinic structure.展开更多
Lithium(Li)metal is an attractive anode material with high capacity(3860 mAh g^(−1))and low potential(−3.04 V vs.standard hydrogen electrode)that shows highly promising for applications requiring high energy density.H...Lithium(Li)metal is an attractive anode material with high capacity(3860 mAh g^(−1))and low potential(−3.04 V vs.standard hydrogen electrode)that shows highly promising for applications requiring high energy density.However,the low electrochemical potential of Li metal makes it extremely reactive and inevitably forming a native oxidized layer in the ambient environment and repeatedly being consumed when exposed to liquid electrolytes.It is therefore beneficial to replace the poorly controlled native passivation layer with a tailored artificial SEI to improve interface management between Li and electrolyte and enhance the stability of Li metal battery.Here,we use an integrated glovebox-atomic layer deposition(ALD)-X-ray photoelectron spectroscopy(XPS)setup to in-situ investigating the pristine Li surface and the surface composition after Ar,H_(2)O_(2),N_(2)and NH_(3)plasma treatment processes.We find that the pristine Li foil is naturally being covered with a native oxidized layer,which is mainly composed of LiOH,Li_(2)O and Li_(2)CO_(3).These investigated plasmas can efficiently remove the oxidized layer from the Li metal surface,in which metallic Li surface is obtained after Ar or H2 plasma treatments,where Ar plasma is more efficient.While O_(2)plasma treatment produces a Li_(2)O layer,and N_(2)or NH_(3)plasma treatment leads to a Li3N(including a certain amount of LiON)layer on the Li surface.When employing the representative metallic Li(by Ar plasma treatment),Li_(2)O layer coated Li(by O_(2)plasma treatment)and Li3N layer coated Li(by N_(2)plasma treatment)foils as electrodes in symmetric Li metal batteries,the Li3N coated Li electrode exhibits much higher stability than that of metallic and Li_(2)O layer coated Li foils.Improved electrochemical performance has also been achieved in LiMn_(2)O_(4)(LMO)||Li full cells using Li anode with Li3N protective coating layer.Our work reveals the detailed process of surface engineering of Li metal anodes with plasma treatments by in vacuo XPS,which may also be extended to other gas-treatment or plasma-treatment for stabilization of high energy density Li metal anodes and other metal-based anodes.展开更多
The layered Li2MnO3 is investigated by using the first-principles calculations within the GGA and GGA-t-U scheme, respectively. Within the GGA4-U approach, the calculated intercalation voltage （ranges from 4,5 V to 4...The layered Li2MnO3 is investigated by using the first-principles calculations within the GGA and GGA-t-U scheme, respectively. Within the GGA4-U approach, the calculated intercalation voltage （ranges from 4,5 V to 4.9 V） is found to be in good agreement with experiments. From the analysis of electronic structure, the pure phase Li2MnO3 is insulating, which is indicative of poor electronic-conduction properties. However, further studies of lithium ion diffusion in bulk Li2MnO3 show that unlike the two-dimensional diffusion pathways in rock salt structure layered cathode materials, lithium can diffuse in a three-dimensional pathway in Li2MnO3, with moderate lithium migration energy barrier ranges from 0.57 to 0.63 e V.展开更多
采用改进的碳酸盐共沉淀与高温固相法相结合的方法制备出了高倍率性能的锂离子电池正极材料Li[Ni1/3Co1/3Mn1/3]O2,通过X射线衍射(XRD)、扫描电镜(SEM)、循环伏安扫描(CV)、电化学阻抗谱(EIS)和电化学性能测试等手段对材料进行表征.结...采用改进的碳酸盐共沉淀与高温固相法相结合的方法制备出了高倍率性能的锂离子电池正极材料Li[Ni1/3Co1/3Mn1/3]O2,通过X射线衍射(XRD)、扫描电镜(SEM)、循环伏安扫描(CV)、电化学阻抗谱(EIS)和电化学性能测试等手段对材料进行表征.结果表明,该方法制备的材料具有良好的α-Na Fe O2型层状结构(R3m(166)),一次粒径平均大小为157 nm,二次颗粒成球形.同传统碳酸盐制备得到的材料相比,该材料具备良好的倍率性能和循环性能,在2.7-4.3 V电压范围内,0.1C(1.0C=180 m A?g-1)倍率下,首次放电比容量为156.4m Ah?g-1,库仑效率为81.9%.在较高倍率下,即0.5C、5.0C和20C时,其放电比容量分别为136.9、111.3、81.3m Ah?g-1.在1C倍率下100次循环容量保持率为92.9%,高于传统共沉淀法得到的材料(87.0%).展开更多
The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and el...The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and electrochemical behaviors of Li[Ni1/3Mn1/3Co1/3]O2 were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, field emission scanning electron microscopy （FESEM） and electrochemical charge/discharge cycling tests. The results show that the difference in pretreatment process results in the difference in compound Li[Ni1/3Co1/3Mn1/3]O2 structure, morphology and the electrochemical characteristics. The Li[Ni1/3Mn1/3Co1/3]O2 prepared by solution phase route maintains the uniform spherical morphology of the [Ni1/3Co1/3Mn1/3]3O4, and it exhibits a higher capacity retention and better rate capability than that prepared by ball mill method. The initial discharge capacity of this sample reaches 178 mA-h/g and the capacity retention after 50 cycles is 98.7% at a current density of 20 mA/g. Moreover, it delivers high discharge capacity of 135 mA-h/g at a current density of 1 000 mA/g.展开更多
Li2SiO3 was synthesized by combination of sol-gel method and calcination at high temperature using Li2CO3, HNO3, Si（OC2H5）4 and C2H5OH as starting materials. The effects of calcination temperature and refluxing syst...Li2SiO3 was synthesized by combination of sol-gel method and calcination at high temperature using Li2CO3, HNO3, Si（OC2H5）4 and C2H5OH as starting materials. The effects of calcination temperature and refluxing system on the composition and properties of lithium silicate were investigated. The samples were characterized by TGA/DTA, XRD, SEM and particle size analysis. Li2FeSiO4 was prepared by the solid-state reaction between Li2SiO3 and FeC2O4·2H2O. The XRD patterns show that the use of refluxing system in the sol-gel preparation can decrease the Li2Si2O5 and Li4SiO4 impurities in the Li2SiO3 sample. The calcination temperature plays an important role in the properties of the Li2SiO3 samples. The sample calcined at 700 °C has high purity of 97% Li2SiO3 and good morphology as precursor of Li2FeSiO4. It consists of primary particles with size of 1-3 μm, and the primary particle clusters form agglomerates with loose and porous appearance.展开更多
基金Project (20771100) supported by the National Natural Science Foundation of China
文摘Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galvanostatic charge /discharge and electrochemical impedance spectroscopy（EIS）. The XRD study shows that a small amount of Mn2＋-doped does not alter the structure of Li3V2（PO4）3/C materials, and all Mn2＋-doped samples are of pure single phase with a monoclinic structure （space group P21/n）. The XPS analysis indicates that valences state of V and Mn are ＋3 and ＋2 in Li3V1.94Mn0.09（PO4）3/C, respectively, and the citric acid in raw materials was decomposed into carbon during calcination, and residual carbon exists in Li3V1.94Mn0.09（PO4）/C. The results of electrochemical measurements show that Mn2＋-doping can improve the cyclic stability and rate performance of these cathode materials. The Li3V1.94Mn0.09（PO4）3/C cathode material shows the best cyclic stability and rate performance. For example, at the discharge current density of 40 mA/g, after 100 cycles, the discharge capacity of Li3V1.94Mn0.09（PO4）3/C declines from initial 158.8 mA·h/g to 120.5 mA·h/g with a capacity retention of 75.9%; however, that of the Mn-undoed sample declines from 164.2 mA·h/g to 72.6 mA·h/g with a capacity retention of 44.2%. When the discharge current is increased up to 1C, the intial discharge capacity of Li3V1.94Mn0.09（PO4）3/C still reaches 146.4 mA·h/g, and the discharge capacity maintains at 107.5 mA·h/g after 100 cycles. The EIS measurement indicates that Mn2＋-doping with a appropriate amount of Mn2＋ decreases the charge transfer resistance, which is favorable for the insertion/extraction of Li＋.
基金supported by Guangxi Natural Science Foundation (0832259)Program to Sponsor Teams for Innovation in the Construction of Talent Highlands in Guangxi Institutions of Higher Learning (GuiJiaoRen [2007]71)Research Funds of the Guangxi Key Laboratory of Environmental Engineering, Protection and Assessment
文摘Y-doped Li3V2（PO4）3 cathode materials were prepared by a carbothermal reduction（CTR） process.The properties of the Y-doped Li3V2（PO4）3 were investigated by X-ray diffraction（XRD） and electrochemical measurements.XRD studies showed that the Y-doped Li3V2（PO4）3 had the same monoclinic structure as the undoped Li3V2（PO4）3.The Y-doped Li3V2（PO4）3 samples were investigated on the Li extraction/insertion performances through charge/discharge, cyclic voltammogram（CV）, and electrochemical impedance spectra（EIS）.The optimal doping content of Y was x=0.03 in Li3V2-xYx（PO4）3 system.The Y-doped Li3V2（PO4）3 samples showed a better cyclic ability.The electrode reaction reversibility was enhanced, and the charge transfer resistance was decreased through the Y-doping.The improved electrochemical perormances of the Y-doped Li3V2（PO4）3 cathode materials were attributed to the addition of Y3＋ ion by stabilizing the monoclinic structure.
基金Key R&D and transformation projects in Hebei Province,Grant/Award Number:21314401DProgram for the Development of Science and Technology of Jilin province,Grant/Award Numbers:20200201187JC,20200201277JC,20200201279JC+4 种基金Project of Development and Reform Commission of Jilin Province,Grant/Award Number:2020C026-3National Natural Science Foundation of China,Grant/Award Numbers:21978110,51772126,52171210Fundamental Research Funds for the Central Universities,Grant/Award Number:2021JCCXJD01Key R&D and transformation projects in Qinghai Province,Grant/Award Number:2021-HZ-808The talents project of Beijing Municipal Committee Organization Department,Grant/Award Number:2018000021223ZK21。
文摘Rational design of porous conductive hosts with high electrical conductivity,large surface area,and adequate interior space is desirable to suppressing dendritic lithium growth and accommodating large volume change of lithium metal anode during the Li plating/stripping process.However,due to the conductive nature of the conductive hosts,Li is easily deposited directly on the top of the hosts,which hinders it from fully functioning.To circumvent the issue,in this study,we designed a novel porous carbon host with a gradient-pore-size structure based on one-dimensional(1D)carbon with different diameters.With this kind of host,stable cycling with high and stable Coulombic efficiency of~98%is achieved at 0.5 mA cm^(−2) with an areal capacity of 1 mAh cm^(−2) over 320 cycles.In contrast,the normal three-dimensional(3D)carbon nanotube host presents a moss-like Li morphology with wildly fluctuating Coulombic efficiency after 100 cycles.The results reveal that the unique gradient-pore-size structure of the 3D conductive host greatly improves the performance of lithium metal batteries.
基金This work was financially supported by National Key Research and Development Program(2018YFE0203502),ChinaPrimary Research and Development Plan ofJiangsu Province(BE2019117),China and National Students'Platform for Innovation and Entrepreneurship Training(201910291051Z),China.
文摘Spinel lithium manganese oxide ion-sieves have been considered the most promising adsorbents to extract Li^+ from brines and sea water.Here,we report a lithium ion-sieve which was successfully loaded onto tubular α-Al2 O3 ceramic substrates by dipping crystallization and post-calcination method.The lithium manganese oxide Li4 Mn5 O(12)was first synthesized onto tubular α-Al2 O3 ceramic substrates as the ion-sieve precursor(i.e.L-AA),and the corresponding lithium ion-sieve(i.e.H-AA) was obtained after acid pickling.The chemical and morphological properties of the ion-sieve were confirmed by X-ray diffraction(XRD) and scanning electron microscopy(SEM).Both L-AA and H-AA showed characteristic peaks of α-Al2 O3 and cubic phase Li4 Mn5 O(12) and the peaks representing cubic phase could still exist after pickling.The lithium manganese oxide Li4 Mn5 O(12) could be uniformly loaded not only on the surface of α-Al2 O3 ubstrates but also inside the pores.Moreover,we found that the equilibrium adsorption capacity of H-AA was 22.9 mg·g^-1.After 12 h adsorption,the adsorption balance was reached.After 5 cycles of adsorption,the adsorption capacity of H-AA was 60.88% of the initial adsorption capacity.The process of H-AA adsorption for Li^+correlated with pseudo-second order kinetic model and Langmuir model.Adsorption thermodynamic parameters regarding enthalpy(△N), Gibbs free energy(△G) and entropy(AS) were calculated.For the dynamic adsorptiondesorption process of H-AA,the H-AA exhibited excellent adsorption performance to Li^+ with the Li^+ dynamic adsorption capacity of 9.74 mg·g^-1 and the Mn^2+dissolution loss rate of 0.99%.After 3 dynamic adsorption-desorption cycles,80% of the initial dynamic adsorption capacity was still kept.
基金Funded by the Guangxi Natural Science Foundation(No. 0832259)the National Basic Research Program of China (No. 2007CB613607)
文摘Cr-doped Li3V2（PO4）3 cathode materials Li3V2-xCr（PO4）3 were prepared by a carbothermal reduction（CTR） process. The properties of the Cr-doped Li3V2（PO4）3 were investigated by X-ray diffraction （XRD）, scanning electron microscopic （SEM）, and electrochemical measurements Results show that the Cr-doped Li3V2（PO4）3 has the same monoclinic structure as the undoped Li3V2（PO4）3, and the particle size of Cr-doped Li3V2（PO4）3 is smaller than that of the undoped Li3V2（PO4）3 and the smallest particle size is only about 1 1μm. The Cr-doped Li3V2（PO4）3 samples were investigated on the Li extraction/insertion performances through charge/discharge, cyclic voltammogram （CV）, and electrochemical impedance spectra（EIS）. The optimal doping content of Cr was that x=0.04 in the Li3V2-xCrx（PO4）3 samples to achieve high discharge capacity and good cyclic stability. The electrode reaction reversibility was enhanced, and the charge transfer resistance was decreased through the Cr-doping. The improved electrochemical performances of the Cr-doped Li3V2（PO4）3 cathode materials are attributed to the addition of Cr^3＋ ion by stabilizing the monoclinic structure.
基金FWO-Vlaanderen(No.GO87418N and 1S68518N)BOF-GOA UGent(No.01G01019)Solvay SA for financial support。
文摘Lithium(Li)metal is an attractive anode material with high capacity(3860 mAh g^(−1))and low potential(−3.04 V vs.standard hydrogen electrode)that shows highly promising for applications requiring high energy density.However,the low electrochemical potential of Li metal makes it extremely reactive and inevitably forming a native oxidized layer in the ambient environment and repeatedly being consumed when exposed to liquid electrolytes.It is therefore beneficial to replace the poorly controlled native passivation layer with a tailored artificial SEI to improve interface management between Li and electrolyte and enhance the stability of Li metal battery.Here,we use an integrated glovebox-atomic layer deposition(ALD)-X-ray photoelectron spectroscopy(XPS)setup to in-situ investigating the pristine Li surface and the surface composition after Ar,H_(2)O_(2),N_(2)and NH_(3)plasma treatment processes.We find that the pristine Li foil is naturally being covered with a native oxidized layer,which is mainly composed of LiOH,Li_(2)O and Li_(2)CO_(3).These investigated plasmas can efficiently remove the oxidized layer from the Li metal surface,in which metallic Li surface is obtained after Ar or H2 plasma treatments,where Ar plasma is more efficient.While O_(2)plasma treatment produces a Li_(2)O layer,and N_(2)or NH_(3)plasma treatment leads to a Li3N(including a certain amount of LiON)layer on the Li surface.When employing the representative metallic Li(by Ar plasma treatment),Li_(2)O layer coated Li(by O_(2)plasma treatment)and Li3N layer coated Li(by N_(2)plasma treatment)foils as electrodes in symmetric Li metal batteries,the Li3N coated Li electrode exhibits much higher stability than that of metallic and Li_(2)O layer coated Li foils.Improved electrochemical performance has also been achieved in LiMn_(2)O_(4)(LMO)||Li full cells using Li anode with Li3N protective coating layer.Our work reveals the detailed process of surface engineering of Li metal anodes with plasma treatments by in vacuo XPS,which may also be extended to other gas-treatment or plasma-treatment for stabilization of high energy density Li metal anodes and other metal-based anodes.
基金Supported by the National Natural Science Foundation of China under Grant No 21363016the Natural Science Foundation of Jiangxi Province under Grant No 20142BAB216030the PhD Early Development Program of Nanchang Hangkong University under Grant No EA201502007
文摘The layered Li2MnO3 is investigated by using the first-principles calculations within the GGA and GGA-t-U scheme, respectively. Within the GGA4-U approach, the calculated intercalation voltage （ranges from 4,5 V to 4.9 V） is found to be in good agreement with experiments. From the analysis of electronic structure, the pure phase Li2MnO3 is insulating, which is indicative of poor electronic-conduction properties. However, further studies of lithium ion diffusion in bulk Li2MnO3 show that unlike the two-dimensional diffusion pathways in rock salt structure layered cathode materials, lithium can diffuse in a three-dimensional pathway in Li2MnO3, with moderate lithium migration energy barrier ranges from 0.57 to 0.63 e V.
文摘采用改进的碳酸盐共沉淀与高温固相法相结合的方法制备出了高倍率性能的锂离子电池正极材料Li[Ni1/3Co1/3Mn1/3]O2,通过X射线衍射(XRD)、扫描电镜(SEM)、循环伏安扫描(CV)、电化学阻抗谱(EIS)和电化学性能测试等手段对材料进行表征.结果表明,该方法制备的材料具有良好的α-Na Fe O2型层状结构(R3m(166)),一次粒径平均大小为157 nm,二次颗粒成球形.同传统碳酸盐制备得到的材料相比,该材料具备良好的倍率性能和循环性能,在2.7-4.3 V电压范围内,0.1C(1.0C=180 m A?g-1)倍率下,首次放电比容量为156.4m Ah?g-1,库仑效率为81.9%.在较高倍率下,即0.5C、5.0C和20C时,其放电比容量分别为136.9、111.3、81.3m Ah?g-1.在1C倍率下100次循环容量保持率为92.9%,高于传统共沉淀法得到的材料(87.0%).
基金Project(20871101)supported by the National Natural Science Foundation of ChinaProject(2009WK2007)supported by Key Project of Science and Technology Department of Hunan Province,ChinaProject(CX2009B133)supported by Colleges and Universities in Hunan Province Plans to Graduate Research and Innovation,China
文摘The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and electrochemical behaviors of Li[Ni1/3Mn1/3Co1/3]O2 were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, field emission scanning electron microscopy （FESEM） and electrochemical charge/discharge cycling tests. The results show that the difference in pretreatment process results in the difference in compound Li[Ni1/3Co1/3Mn1/3]O2 structure, morphology and the electrochemical characteristics. The Li[Ni1/3Mn1/3Co1/3]O2 prepared by solution phase route maintains the uniform spherical morphology of the [Ni1/3Co1/3Mn1/3]3O4, and it exhibits a higher capacity retention and better rate capability than that prepared by ball mill method. The initial discharge capacity of this sample reaches 178 mA-h/g and the capacity retention after 50 cycles is 98.7% at a current density of 20 mA/g. Moreover, it delivers high discharge capacity of 135 mA-h/g at a current density of 1 000 mA/g.
基金Foundation item: Project (2007CB613607) support by the National Basic Research Program of ChinaProject (2010QZZD0101) supported by the Basic Research Foundation for the Chinese Central Universities
文摘Li2SiO3 was synthesized by combination of sol-gel method and calcination at high temperature using Li2CO3, HNO3, Si（OC2H5）4 and C2H5OH as starting materials. The effects of calcination temperature and refluxing system on the composition and properties of lithium silicate were investigated. The samples were characterized by TGA/DTA, XRD, SEM and particle size analysis. Li2FeSiO4 was prepared by the solid-state reaction between Li2SiO3 and FeC2O4·2H2O. The XRD patterns show that the use of refluxing system in the sol-gel preparation can decrease the Li2Si2O5 and Li4SiO4 impurities in the Li2SiO3 sample. The calcination temperature plays an important role in the properties of the Li2SiO3 samples. The sample calcined at 700 °C has high purity of 97% Li2SiO3 and good morphology as precursor of Li2FeSiO4. It consists of primary particles with size of 1-3 μm, and the primary particle clusters form agglomerates with loose and porous appearance.
