Na-doped Li1.05Mn2O4 cathodes were synthesized using a sol-gel process.The samples were characterized by X-ray diffractometry(XRD),cyclic voltammetry(CV),electrochemical impedance spectroscopy(EIS)and charge-discharge...Na-doped Li1.05Mn2O4 cathodes were synthesized using a sol-gel process.The samples were characterized by X-ray diffractometry(XRD),cyclic voltammetry(CV),electrochemical impedance spectroscopy(EIS)and charge-discharge measurements. The results show that all the samples exhibit the same cubic spinel phase structure without impurity.The lattice constant and unit cell volume decrease with increasing the sodium dopant amount.As the molar ratio of sodium to manganese(x=n(Na)/n(Mn))increases from 0 to 0.03,the initial discharge capacity of the Li1.05Mn2O4 cathodes decreases from 119.2 to 107.9 mA·h/g,and the discharge capability at large current rate and the storage performance decline dramatically,while cycling performance at room temperature and 55℃are improved.The CV and EIS studies indicate that reversibility of Li1.05Mn2O4 cathodes decreases and the electrochemical impedance increases with increasing the sodium dopant amount.展开更多
The hydrothermal synthesis of single-crystallineβ-MnO2 nanorods and their chemical conversion into single-crystalline LiMn2O4 nanorods by a simple solid-state reaction were reported.This method has the advantages of ...The hydrothermal synthesis of single-crystallineβ-MnO2 nanorods and their chemical conversion into single-crystalline LiMn2O4 nanorods by a simple solid-state reaction were reported.This method has the advantages of producing pure,single-phase and crystalline nanorods.The LiMn2O4 nanorods have an diameter of about 300 nm.The discharge capacity and cyclic performance of the batteries were investigated.The LiMn2O4 nanorods show better cyclic performance with a capacity retention ratio of 86.2% after 100 cycles.Battery cyclic studies reveal that the prepared LiMn2O4 nanorods have high capacity with a first discharge capacity of 128.7 mA·h/g.展开更多
LiNi0. 45 Co0. 10 Mn0. 4sO2 was synthesized from Li2CO3 and a triple oxide of nickel, cobalt and manganese at 950 ℃ in air. The structures and characteristics of LiNi0. 45 Co0.10 Mn0. 45 O2, LiCoO2 and LiMn2 O4 were ...LiNi0. 45 Co0. 10 Mn0. 4sO2 was synthesized from Li2CO3 and a triple oxide of nickel, cobalt and manganese at 950 ℃ in air. The structures and characteristics of LiNi0. 45 Co0.10 Mn0. 45 O2, LiCoO2 and LiMn2 O4 were investigated by XRD, SEM and electrochemical measurements. The results show that LiNi0.4s Co0.10 Mn0. 45 O2 has a layered structure with hexagonal lattice. The commercial LicoO2 has sphere-like appearance and smooth surfaces, while the LiMn2 O4 and LiNi0.45 Co0. 10 Mn0. 45 O2 consist of cornered and uneven particles. LiNi0. 45 Co0.10 Mn0. 45 O2 has a large disLiMn2 O4 and LiCoO2, respectively. LiCoO2 and LiMn2 O4 have higher discharge voltage and better rate-capability than LiNi0. 45Co0.10 Mn0. 45 O2. All the three cathodes have excellent cycling performance with capacity retention of above 89.3 % at the 250th cycle. Batteries with LiMn2 O4 or LiNi0.45 Co0.10 Mn0. 45 O2 cathodes show better safety performance under abusive conditions than those with LiCoO2 cathodes.展开更多
The spinel LiMn2O4 used as cathode materials for lithium-ion batteries was synthesized by mechanochemistry fluid activation process, and modified by doping rare-earth Sm. Testing of X-ray diffraction, cyclic voltammog...The spinel LiMn2O4 used as cathode materials for lithium-ion batteries was synthesized by mechanochemistry fluid activation process, and modified by doping rare-earth Sm. Testing of X-ray diffraction, cyclic voltammograms, charge-discharge and SEM was carried out for LiMn2O4 cathode materials and the modified materials.The results show that the cathode materials doped rare earth LixMn2-ySmxO4 (0.95≤x≤1.2, 0≤y≤0.3, 0≤z≤0.2) exhibit standard spinel structure, high reversibility of electrochemistry and excellent properties of charge-discapacity is deteriorated less than 15% after 300 cycles at room temperature and less than 20% after 200 cycles at 55 C.At the same time, Crystal Field Theory was applied to explain the function and mechanism of doped rare earth element.展开更多
A prismatic 204056-type high power lithium-ion battery was developed.Modified LiMn2O4 and carbonaceous mesophase sphere(CMS)were adopted as the cathode and anode,respectively.The effects of proportion of conductive ca...A prismatic 204056-type high power lithium-ion battery was developed.Modified LiMn2O4 and carbonaceous mesophase sphere(CMS)were adopted as the cathode and anode,respectively.The effects of proportion of conductive carbon black in cathode and the rest time after discharge on the electrochemical properties of batteries were investigated.The electrochemical tests show that the proportion of conductive carbon black in cathodes affects the high rate capability and discharge voltage plateau distinctly.The battery with 3.0%of conductive carbon black in cathode shows excellent electrochemical performances when being charged/discharged within 2.5-4.2 V at room temperature.The discharge capacity at 20C rate is 94.4%of that at 1C rate,and the capacity retention ratio charged at 1C and discharged at 5C is 86.6%after 390 cycles at room temperature.The test result of impulse discharge at 50C for 5 s shows that the battery has outstanding high rate discharge performance when the battery is in the depth of charge of 90%,75%,60%,45%,30%and 15%.The battery also shows good charge performance.When the battery is charged at 0.5C,1C,2C and 4C,the ratios of capacity for constant current charge are 98.4%,96.4%,91.0%and 72.9%of the whole charge capacity,respectively.In addition,the rest time after discharge affects the cycle performance distinctly when the battery is discharged at high rate.展开更多
Spinel LiMn2O4 microspheres and hollow microspheres with adjustable wall thickness have been prepared using controllable oxidation of MnCO3 microspheres precursors and following solid reactions with lithium salts. Sca...Spinel LiMn2O4 microspheres and hollow microspheres with adjustable wall thickness have been prepared using controllable oxidation of MnCO3 microspheres precursors and following solid reactions with lithium salts. Scanning electron microscopy （SEM） investigations demonstrate that the microsphere morphology and hollow structure of precursors are inherited. The effect of hollow structure properties of as-prepared LiMn2O4 on their performance as cathode materials for lithium-ion batteries has been studied. Electrochemical performance tests show that LiMn2O4 hollow microspheres with small wall thickness exhibit both superior rate capability and better cycle performance than LiMn2O4 solid microspheres and LiMn2O4 hollow microspheres with thick wall. The LiMn2O4 hollow microspheres with thin wall have discharge capacity of 132.7 mA.h-g^-1 at C/10 （14.8 mA.g^-1） in the first cycle, 94.1% capacity retention at C/10 after 40 cycles and discharge capacity of 116.5 mAh-gq at a high rate of 5C. The apparent lithium-ion diffusion coefficient （Dapp） of as-prepared LiMn2O4 determined by capacity intermittent titration technique （CITT） varies from 10-11 to 10-8.5 cm2.s^-1 showing a regular ＂W＂ shape curve plotted with test voltages. The D app of LiMn2O4 hollow microspheres with thin wall has the largest value among all the prepared samples. Both the superior rate capability and cycle stability of LiMn2O4 hollow microspheres with thin wall can be ascribed to the facile ion diffusion in the hollow structures and the robust of hollow structures during repeated cycling.展开更多
LiCoO2 surface layer is proposed and prepared through sol-gel method. The physical and electrochemical performances of pristine LiMn2O4 and LiCoO2-coated LiMn2O4 cathode materials were investigated by X-ray diffractio...LiCoO2 surface layer is proposed and prepared through sol-gel method. The physical and electrochemical performances of pristine LiMn2O4 and LiCoO2-coated LiMn2O4 cathode materials were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, electrochemical measurements respectively. Comparing with the pristine LiMn2O4, the LiCoO2- coated LiMn2O4 phase significantly improved cycling stability, especially at 55°C. Additionally, the thermal safety of LiMn2O4 is greatly enhanced after being coated by LiCoO2. ICP-AES measurement, structural analysis, and impedance experiments indicate that the improved electrochemical property of LiCoO2-coated LiMn2O4 should be attributed to the alleviated dissolution loss of manganese, strengthened structural stability.展开更多
基金Project(2007CB613607) supported by the National Basic Research Program of ChinaProjects(2009FJ1002, 2009CK3062) supported by the Science and Technology Program of Hunan Province, China
文摘Na-doped Li1.05Mn2O4 cathodes were synthesized using a sol-gel process.The samples were characterized by X-ray diffractometry(XRD),cyclic voltammetry(CV),electrochemical impedance spectroscopy(EIS)and charge-discharge measurements. The results show that all the samples exhibit the same cubic spinel phase structure without impurity.The lattice constant and unit cell volume decrease with increasing the sodium dopant amount.As the molar ratio of sodium to manganese(x=n(Na)/n(Mn))increases from 0 to 0.03,the initial discharge capacity of the Li1.05Mn2O4 cathodes decreases from 119.2 to 107.9 mA·h/g,and the discharge capability at large current rate and the storage performance decline dramatically,while cycling performance at room temperature and 55℃are improved.The CV and EIS studies indicate that reversibility of Li1.05Mn2O4 cathodes decreases and the electrochemical impedance increases with increasing the sodium dopant amount.
基金Project(2008AA031205)supported by the National High-tech Research and Development Program of China
文摘The hydrothermal synthesis of single-crystallineβ-MnO2 nanorods and their chemical conversion into single-crystalline LiMn2O4 nanorods by a simple solid-state reaction were reported.This method has the advantages of producing pure,single-phase and crystalline nanorods.The LiMn2O4 nanorods have an diameter of about 300 nm.The discharge capacity and cyclic performance of the batteries were investigated.The LiMn2O4 nanorods show better cyclic performance with a capacity retention ratio of 86.2% after 100 cycles.Battery cyclic studies reveal that the prepared LiMn2O4 nanorods have high capacity with a first discharge capacity of 128.7 mA·h/g.
基金Project(50302016) supported by the National Natural Science Foundation of China Project(2005037698) supported by the Postdoctoral Science Foundation of China
文摘LiNi0. 45 Co0. 10 Mn0. 4sO2 was synthesized from Li2CO3 and a triple oxide of nickel, cobalt and manganese at 950 ℃ in air. The structures and characteristics of LiNi0. 45 Co0.10 Mn0. 45 O2, LiCoO2 and LiMn2 O4 were investigated by XRD, SEM and electrochemical measurements. The results show that LiNi0.4s Co0.10 Mn0. 45 O2 has a layered structure with hexagonal lattice. The commercial LicoO2 has sphere-like appearance and smooth surfaces, while the LiMn2 O4 and LiNi0.45 Co0. 10 Mn0. 45 O2 consist of cornered and uneven particles. LiNi0. 45 Co0.10 Mn0. 45 O2 has a large disLiMn2 O4 and LiCoO2, respectively. LiCoO2 and LiMn2 O4 have higher discharge voltage and better rate-capability than LiNi0. 45Co0.10 Mn0. 45 O2. All the three cathodes have excellent cycling performance with capacity retention of above 89.3 % at the 250th cycle. Batteries with LiMn2 O4 or LiNi0.45 Co0.10 Mn0. 45 O2 cathodes show better safety performance under abusive conditions than those with LiCoO2 cathodes.
基金Project (02JJY2081) supported by the Natural Science Foundation of Hunan Province
文摘The spinel LiMn2O4 used as cathode materials for lithium-ion batteries was synthesized by mechanochemistry fluid activation process, and modified by doping rare-earth Sm. Testing of X-ray diffraction, cyclic voltammograms, charge-discharge and SEM was carried out for LiMn2O4 cathode materials and the modified materials.The results show that the cathode materials doped rare earth LixMn2-ySmxO4 (0.95≤x≤1.2, 0≤y≤0.3, 0≤z≤0.2) exhibit standard spinel structure, high reversibility of electrochemistry and excellent properties of charge-discapacity is deteriorated less than 15% after 300 cycles at room temperature and less than 20% after 200 cycles at 55 C.At the same time, Crystal Field Theory was applied to explain the function and mechanism of doped rare earth element.
基金Project(2007CB613607)supported by the National Basic Research Program of China
文摘A prismatic 204056-type high power lithium-ion battery was developed.Modified LiMn2O4 and carbonaceous mesophase sphere(CMS)were adopted as the cathode and anode,respectively.The effects of proportion of conductive carbon black in cathode and the rest time after discharge on the electrochemical properties of batteries were investigated.The electrochemical tests show that the proportion of conductive carbon black in cathodes affects the high rate capability and discharge voltage plateau distinctly.The battery with 3.0%of conductive carbon black in cathode shows excellent electrochemical performances when being charged/discharged within 2.5-4.2 V at room temperature.The discharge capacity at 20C rate is 94.4%of that at 1C rate,and the capacity retention ratio charged at 1C and discharged at 5C is 86.6%after 390 cycles at room temperature.The test result of impulse discharge at 50C for 5 s shows that the battery has outstanding high rate discharge performance when the battery is in the depth of charge of 90%,75%,60%,45%,30%and 15%.The battery also shows good charge performance.When the battery is charged at 0.5C,1C,2C and 4C,the ratios of capacity for constant current charge are 98.4%,96.4%,91.0%and 72.9%of the whole charge capacity,respectively.In addition,the rest time after discharge affects the cycle performance distinctly when the battery is discharged at high rate.
基金Funded by the National Natural Science Foundation of China(Nos.20803056,11474226)the Fundamental Research Funds for the Central Universities(WUT:2015-IB-001,WUT:2016-IB-005)
文摘Spinel LiMn2O4 microspheres and hollow microspheres with adjustable wall thickness have been prepared using controllable oxidation of MnCO3 microspheres precursors and following solid reactions with lithium salts. Scanning electron microscopy （SEM） investigations demonstrate that the microsphere morphology and hollow structure of precursors are inherited. The effect of hollow structure properties of as-prepared LiMn2O4 on their performance as cathode materials for lithium-ion batteries has been studied. Electrochemical performance tests show that LiMn2O4 hollow microspheres with small wall thickness exhibit both superior rate capability and better cycle performance than LiMn2O4 solid microspheres and LiMn2O4 hollow microspheres with thick wall. The LiMn2O4 hollow microspheres with thin wall have discharge capacity of 132.7 mA.h-g^-1 at C/10 （14.8 mA.g^-1） in the first cycle, 94.1% capacity retention at C/10 after 40 cycles and discharge capacity of 116.5 mAh-gq at a high rate of 5C. The apparent lithium-ion diffusion coefficient （Dapp） of as-prepared LiMn2O4 determined by capacity intermittent titration technique （CITT） varies from 10-11 to 10-8.5 cm2.s^-1 showing a regular ＂W＂ shape curve plotted with test voltages. The D app of LiMn2O4 hollow microspheres with thin wall has the largest value among all the prepared samples. Both the superior rate capability and cycle stability of LiMn2O4 hollow microspheres with thin wall can be ascribed to the facile ion diffusion in the hollow structures and the robust of hollow structures during repeated cycling.
文摘LiCoO2 surface layer is proposed and prepared through sol-gel method. The physical and electrochemical performances of pristine LiMn2O4 and LiCoO2-coated LiMn2O4 cathode materials were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, electrochemical measurements respectively. Comparing with the pristine LiMn2O4, the LiCoO2- coated LiMn2O4 phase significantly improved cycling stability, especially at 55°C. Additionally, the thermal safety of LiMn2O4 is greatly enhanced after being coated by LiCoO2. ICP-AES measurement, structural analysis, and impedance experiments indicate that the improved electrochemical property of LiCoO2-coated LiMn2O4 should be attributed to the alleviated dissolution loss of manganese, strengthened structural stability.
