Railway ballast forms a major component of a conventional rail track and is used to distribute the load to the subgrade, providing a smooth running surface for trains. It plays a significant role in providing support ...Railway ballast forms a major component of a conventional rail track and is used to distribute the load to the subgrade, providing a smooth running surface for trains. It plays a significant role in providing support for the rail track base and distributing the load to the weaker layer underneath. Ballast also helps with drainage, which is an important factor for any type of transportation structure, including railroads. Over time, ballast progressively deforms and degrades under dynamic loading and loses its strength. In this study, extensive laboratory tests were conducted to investigate the effect of load amplitude, geogrid position, and number of geogrid layers, thickness of ballast layer and clay stiffness on the behavior of the reinforced ballast layer and induced strains in a geogrid. A half full-scale railway was constructed for carrying out the tests, which consisted of two rails 800 mm in length with three wooden sleepers(900 mm × 10 mm × 10 mm). Three ballast thicknesses of 200, 300 and 400 mm were used in the tests. The ballast was overlying 500 mm thickness clay in two states, soft and stiff. The tests were carried out with and without geogrid reinforcement; the tests were performed in a well-tied steel box of 1.5 m length ×1 m width ×1 m height. Laboratory tests were conducted to investigate the response of the ballast and the clay layers where the ballast was reinforced by a geogrid. Settlement in ballast and clay, soil pressure and pore water pressure induced in the clay were measured in reinforced and unreinforced ballast cases. It was concluded that the amount of settlement increased as the simulated train load amplitude increased, and there was a sharp increase in settlement up to cycle 500. After that, there was a gradual increase that leveled out between, 2500 to 4500 cycles depending on the frequency used. There was a slight increase in the induced settlement when the load amplitude increased from 0.5 to 1 ton but it was higher when the load amplitude increased to 2 tons. The increased amount in settlement depended on the existence of the geogrid and other parameters studied. The transmitted average vertical stress for ballast thicknesses of 30 cm and 40 cm increased as the load amplitude increased, regardless of the ballast reinforcement for both soft and stiff clay. The position of the geogrid had no significant effect on the transmitted stresses. The value of the soil pressure and pore water pressure on ballast thicknesses of 20 cm was higher than for 30 cm and 40 cm thicknesses. This meant that the ballast attenuated the induced waves. The soil pressure and pore water pressure for reinforced and unreinforced ballast was higher in stiff clay than in soft clay.展开更多
The main factor that contributes to the deterioration of track components is traffic load. Explanations on how the speed, load and repetition of traffic influence the long-term settlement of ballast in a ballasted tra...The main factor that contributes to the deterioration of track components is traffic load. Explanations on how the speed, load and repetition of traffic influence the long-term settlement of ballast in a ballasted track are very scarce. Having in mind that tracks subjected to the same load show different settlement behaviors, explanations of track settlements in accordance with the speed, load and repetition are needed. This study is motivated to show how traffic affects the long-term settlement of ballast and how the traffic parameters (speed, load and repetition) contribute to the process. Using finite element modeling software, the three-dimensional track is modeled and analyzed for different values of speed, load and number of repetitions. Drucker Prager plastic model is applied for the ballast and sub-ballast materials of the track. To get the parameters for the Drucker Prager plastic model of granular materials, triaxial test simulation is performed using discrete element software. Hertz’s contact theory is used to model the contact between the wheel and rail. The long-term settlement behavior of ballast material is analyzed by applying 8000 cycles of moving axel load. According to the analyses, a change in the speed and the number of repetitions of train movement changes the permanent settlement of ballast more than the variation in load. Increase in the speed of train movement by 20 km/hr. will increase the stress transferred to the subgrade by up to about 1000 kPa. Speed of train movement is the most contributing parameter in the degradation of ballast material more than the load and number of repetitions. In a conventional ballasted track after about 6000 repetitions of train movement ballast material will start to decrease its performance. The comparison of the effects of the variation of individual traffic parameters speed, load and number of repetitions on the settlement of ballast which is not touched by former researches is well addressed by this study which is very helpful for designing a new railway track and monitoring existing railway tracks. Based on the analysis of the model with the parameters from Ethio-Djibouti standard gauge railway track, the possible maintenance period of ballast material is predicted.展开更多
This paper presents the results of field and laboratory tests of railway ballast.Field tests were aimed to study vibrational acceleration of ballast particles and ballast layer stressed state in terms of train traffic...This paper presents the results of field and laboratory tests of railway ballast.Field tests were aimed to study vibrational acceleration of ballast particles and ballast layer stressed state in terms of train traffic with heavy axle loads.The test results are vibrational acceleration and stress values distribution in ballast layer and experimental relationships of vertical and horizontal vibroaccelerations damping in terms of train operation with axle load up to 300 k N.Laboratory stabilometer tests were directed to study the change of ballast strength properties due to vibrodynamic impact and shows that for dynamic loading with 10,25,55 Hz frequencies vibrodynamic impact influences strength properties insignificantly and coincides with the accuracy of test equipment.Stated test results provide references for calculation of ballast and sub-ballast bearing capacity.展开更多
文摘Railway ballast forms a major component of a conventional rail track and is used to distribute the load to the subgrade, providing a smooth running surface for trains. It plays a significant role in providing support for the rail track base and distributing the load to the weaker layer underneath. Ballast also helps with drainage, which is an important factor for any type of transportation structure, including railroads. Over time, ballast progressively deforms and degrades under dynamic loading and loses its strength. In this study, extensive laboratory tests were conducted to investigate the effect of load amplitude, geogrid position, and number of geogrid layers, thickness of ballast layer and clay stiffness on the behavior of the reinforced ballast layer and induced strains in a geogrid. A half full-scale railway was constructed for carrying out the tests, which consisted of two rails 800 mm in length with three wooden sleepers(900 mm × 10 mm × 10 mm). Three ballast thicknesses of 200, 300 and 400 mm were used in the tests. The ballast was overlying 500 mm thickness clay in two states, soft and stiff. The tests were carried out with and without geogrid reinforcement; the tests were performed in a well-tied steel box of 1.5 m length ×1 m width ×1 m height. Laboratory tests were conducted to investigate the response of the ballast and the clay layers where the ballast was reinforced by a geogrid. Settlement in ballast and clay, soil pressure and pore water pressure induced in the clay were measured in reinforced and unreinforced ballast cases. It was concluded that the amount of settlement increased as the simulated train load amplitude increased, and there was a sharp increase in settlement up to cycle 500. After that, there was a gradual increase that leveled out between, 2500 to 4500 cycles depending on the frequency used. There was a slight increase in the induced settlement when the load amplitude increased from 0.5 to 1 ton but it was higher when the load amplitude increased to 2 tons. The increased amount in settlement depended on the existence of the geogrid and other parameters studied. The transmitted average vertical stress for ballast thicknesses of 30 cm and 40 cm increased as the load amplitude increased, regardless of the ballast reinforcement for both soft and stiff clay. The position of the geogrid had no significant effect on the transmitted stresses. The value of the soil pressure and pore water pressure on ballast thicknesses of 20 cm was higher than for 30 cm and 40 cm thicknesses. This meant that the ballast attenuated the induced waves. The soil pressure and pore water pressure for reinforced and unreinforced ballast was higher in stiff clay than in soft clay.
文摘The main factor that contributes to the deterioration of track components is traffic load. Explanations on how the speed, load and repetition of traffic influence the long-term settlement of ballast in a ballasted track are very scarce. Having in mind that tracks subjected to the same load show different settlement behaviors, explanations of track settlements in accordance with the speed, load and repetition are needed. This study is motivated to show how traffic affects the long-term settlement of ballast and how the traffic parameters (speed, load and repetition) contribute to the process. Using finite element modeling software, the three-dimensional track is modeled and analyzed for different values of speed, load and number of repetitions. Drucker Prager plastic model is applied for the ballast and sub-ballast materials of the track. To get the parameters for the Drucker Prager plastic model of granular materials, triaxial test simulation is performed using discrete element software. Hertz’s contact theory is used to model the contact between the wheel and rail. The long-term settlement behavior of ballast material is analyzed by applying 8000 cycles of moving axel load. According to the analyses, a change in the speed and the number of repetitions of train movement changes the permanent settlement of ballast more than the variation in load. Increase in the speed of train movement by 20 km/hr. will increase the stress transferred to the subgrade by up to about 1000 kPa. Speed of train movement is the most contributing parameter in the degradation of ballast material more than the load and number of repetitions. In a conventional ballasted track after about 6000 repetitions of train movement ballast material will start to decrease its performance. The comparison of the effects of the variation of individual traffic parameters speed, load and number of repetitions on the settlement of ballast which is not touched by former researches is well addressed by this study which is very helpful for designing a new railway track and monitoring existing railway tracks. Based on the analysis of the model with the parameters from Ethio-Djibouti standard gauge railway track, the possible maintenance period of ballast material is predicted.
文摘This paper presents the results of field and laboratory tests of railway ballast.Field tests were aimed to study vibrational acceleration of ballast particles and ballast layer stressed state in terms of train traffic with heavy axle loads.The test results are vibrational acceleration and stress values distribution in ballast layer and experimental relationships of vertical and horizontal vibroaccelerations damping in terms of train operation with axle load up to 300 k N.Laboratory stabilometer tests were directed to study the change of ballast strength properties due to vibrodynamic impact and shows that for dynamic loading with 10,25,55 Hz frequencies vibrodynamic impact influences strength properties insignificantly and coincides with the accuracy of test equipment.Stated test results provide references for calculation of ballast and sub-ballast bearing capacity.
