Evolution of mechanical properties,localized corrosion resistance and microstructure of a high purity Al-Zn-Mg-Cu alloy during non-isothermal aging

The evolution of mechanical properties,localized corrosion resistance of a high purity Al-Zn-Mg-Cu alloy during non-isothermal aging(NIA)was investigated by hardness test,electrical conductivity test,tensile test,intergranular corrosion test,exfoliation corrosion test,slow strain rate tensile test and electrochemical test,and the mechanism has been discussed based on microstructure examination by optical microscopy,electron back scattered diffraction,scanning electron microscopy and scanning transmission electron microscopy.The NIA treatment includes a heating stage from 40℃to 180℃with a rate of 20℃/h and a cooling stage from 180℃to 40℃with a rate of 10℃/h.The results show that the hardness and strength increase rapidly during the heating stage of NIA since the increasing temperature favors the nucleation and the growth of strengthening precipitates and promotes the transformation of Guinier-Preston(GPI)zones toη'phase.During the cooling stage,the sizes ofη'phase increase with a little change in the number density,leading to a further slight increase of the hardness and strength.As NIA proceeds,the corroded morphology in the alloy changes from a layering feature to a wavy feature,the maximum corrosion depth decreases,and the reason has been analyzed based on the microstructural and microchemical feature of precipitates at grain boundaries and subgrain boundaries.

In-situ AFM and quasi-in-situ studies for localized corrosion in Mg-9Al-1Fe-(Gd) alloys under 3.5 wt.% NaCl environment

Revealing the localized corrosion process of Mg alloy is considered as one of the most significant ways for improving its corrosion resistance.The reliable monitor should be high distinguishability and real-time in liquid environment.Herein,Mg-9Al-1Fe and Mg-9Al-1Fe-1Gd alloys were designed to highlight the impact of intermetallic on the corrosion behaviour.In-situ AFM with a special electrolyte circulation system and quasi-in-situ SEM observation were used to monitor the corrosion process of the designed alloys.SEM-EDS and TEM-SAED were applied to identify the intermetallic in the designed alloys,and their volta potentials were measured by SKPFM.According to the real-time and real-space in-situ AFM monitor,the corrosion process consisted of dissolution of anodicα-Mg phase,accumulation of corrosion products around cathodic phase and shedding of some fine cathodic phase.Then,the localized corrosion process of Mg alloy was revealed combined with the results of the monitor of corrosion process and Volta potential difference.

Effect of nonmetallic inclusions on localized corrosion of spring steel

Certain inclusions in high-strength 60Si2Mn-Cr spring steel result in poor resistance to localized corrosion.In this work,to study the effect of inclusions on the localized corrosion behavior of spring steel,accelerated corrosion tests were performed by immersing spring steel in 3wt%FeCl_(3)solution for different times.The results show that severe corrosion occurred in areas of clustered CaS inclusions.Sulfide inclusions containing Ca and Mg induced the strongest localized corrosion susceptibility.For the case of(Ca,Mn,Mg)S inclusions,the ability to induce localized corrosion susceptibility is ranked as follows:MgS>CaS>MnS.Moreover,CaS,(Ca,Mn)S,and(Ca,Mn,Mg)S inclusions were mainly responsible for inducing environmental embrittlement.

Localized Corrosion and Stress Corrosion Cracking Behavior of AA7003 in a 3.5 wt% NaCl Aqueous Solution

The microstructure,localized corrosion (LC) and stress corrosion cracking (SCC) behavior of 7003 aluminum alloy (AA7003) under various aging treatments (peak aging (PA),double peak aging (DPA),regression and re-aging (RRA)) were investigated by means of transmission electron microscope (TEM),scanning electron microscopy (SEM),electrochemical impendence spectroscopy (EIS) and slow strain rate tensile test.The results of TEM showed a discontinuous distribution of grain boundary precipitates of AA7003 under DPA and RRA treatments,which is beneficial for increasing the resistance of LC and SCC.Meanwhile,LC was found initiating firstly on intermetallics which caused the dissolution of surrounding matrix,then pitting holes were formed and developed into matrix.In addition,the SCC process of AA7003 could be divided into two stages,i e,initial pre-cracking and breeding cracking.The EIS analysis,cross-section morphologies and fracture surfaces of specimens indicated that DPA and RRA treatments significantly decreased the crack growth rate during breeding cracking stage,especially for RRA treatment.

LOCALIZED CORROSION OF MICROCRYSTALS OF 1Crl8Ni9Ti STAINLESS STEEL

The resistances against localized corrosion of 1Cr18Ni9Ti microcrystals with normal grain size and bcc structure obtained hy magnetron sputtering have been compared.The two kinds of microcrystals with (110) and (211) textures respectively were obtained under different sputtering conditions.Both microcrystals were found to have better resistance against local- ized corrosion than the crystal with normal grain.The microcrystal with (110) preferred orientation has larger resistance to localized corrosion than that with (211) preferred orientation.

Studies on the Construction Parameter of an Artificial Occluded Cell for In-situ Inspection of the Propagation Rate of Localized Corrosion

An artificial localized corrosion system is assembled and some parameters related to the localized corrosion in active dissolution state (i.e., non-passive state) have been studied. The results showed that the developed electrochemical system can satisfactorily imitate a naturally formed localized corrosion and the coupling current can indicate the maximum localized propagating rate. In this artificial system, the anodic dissolution reaction followed the auto-catalytic mechanism. The localized corrosion current density was dependent on the area ratio R of the cathode to the occluded anode. While R was equal to or more than 6, the coupling current reached at a maximum value and did not alter with the increase in R-value. Therefore, R=7 is chosen as one of these optimum parameters used in constructing the system, with which the biggest galvanic current might be obtained. In contrast, the thickness of the polymer filler separating the occluded anode area from the bulk electrolyte solution and the volume of the occluded anode area did not affect the corrosion current obviously. They might affect the response time to approach a steady state.

Localized Corrosion in Copper Tubes by Volatile Organic Substance

An unusual form of localized corrsion in copper tubes was detected early in service and in leakage tests after manufacturing.The morphology of this corrosion is similar to that of an ant's nest when viewed in cross section. The corrosion mechanisms, cases ofant's nest corrosion, and preventive measures are presented.

Insight into the triggering effect of(Al,Mg,Ca,Mn)-oxy-sulfide inclusions on localized corrosion of weathering steel

The surface properties of weathering steel(WS)is very important for its service performance and safety,and the localized corrosion induced by inclusions is closely related to the surface properties of WS and its application.In the current work,a common spherical(Al,Mg,Ca,Mn)-oxy-sulfide inclusion was selected to investigate the corrosion evolution of complex inclusion and its effect on localized corrosion on WS surface.The results indicate the inclusion in WS consists of(Ca,Mn)sulfides part and(Ca,Al,Mg)oxides part with complex core-shell structure.Locally preferential dissolution occurs in(Ca,Mn)sulfides part as well as metal matrix around the inclusions.Furthermore,both parts of the inclusions with poor conductivity and high-density dislocation at metal matrix around the inclusions was found,which suggests that traditional micro-galvanic corrosion cell may not be the cause of inclusion-induced localized corrosion on WS surface at initial stage of corrosion.The variation in maximum and average depth around the inclusion or selected region with immersion time indicates that localized corrosion induced by inclusions is overwhelmed by uniform corrosion of WS in the latter stage of immersion,then the rust formed on WS surface consists of two layers.

Localized Corrosion Characteristics of Nickel Alloys： A Review

There are a great variety of commercial nickel alloys mainly because nickel is able to dissolve a large amount of alloying elements while maintaining a single ductile austenitic phase. Nickel alloys are generally designed for and used in highly aggressive environments, for example, those where stainless steels may experience pitting corrosion or environmentally assisted cracking. While nickel alloys are generally resistant to pitting corrosion in chloride-containing environments, they may be prone to crevice corrosion attack. Addition of chromium, molybdenum and tungsten increases the localized corrosion resistance of nickel alloys. This review on the resistance to localized corrosion of nickel alloys includes specific environments such as those present in oil and gas upstream operations, in the chemical process industry and in seawater service.

Initiation and propagation of localized corrosion induced by(Zr,Ti,Al)-O_(x) inclusions in low-alloy steels in marine environment

The effects of inclusions on localized corrosion of Zr–Ti deoxidized low-alloy steels in marine environment were investigated by various analytical techniques including scanning electron microscopy with X-ray microanalysis(SEM/EDS),confocal Raman microscopy(CRM),and in situ scanning vibrating electrode technique(SVET).It was found that complex(Zr,Ti,Al)-O_(x)inclusions were responsible for the initiation of localized corrosion.Localized corrosion pref-erentially occurred at Fe matrix adjacent to these inclusions and formed micro-gaps.In the early stage of corrosion,catalytic-occluded cells and the diffusion of chloride ions played a major role in the propagation of corrosion,further accelerating the dissolution of Fe matrix and(Zr,Ti,Al)-O_(x)inclusions.Combining SVET and CRM results,it revealed that the maximum anodic current density in local area gradually decreased with prolonged exposure time,indicating that corrosion products covered the steel surface and lowered the propagation rate of corrosion.In the later stage of corrosion,the barrier effect of corrosion products played an important role in inhibiting localized corrosion.

Pitting corrosion behavior and corrosion protection performance of cold sprayed double layered noble barrier coating on magnesium-based alloy in chloride containing solutions

Nitrogen processed, cold sprayed commercially pure(CP)-Al coatings on Mg-based alloys mostly lack acceptable hardness, wear resistance and most importantly are highly susceptible to localized corrosion in chloride containing solutions. In this research, commercially pure α-Ti top coating having good pitting potential(~1293 mV_(SCE)), high microhardness(HV_(0.025): 263.03) and low wear rate was applied on a CP-Al coated Mg-based alloy using high pressure cold spray technology. Potentiodynamic polarization(PDP) curves indicated that the probability of transition from metastable pits to the stable pits for cold spayed(CS) Al coating is considerably higher compared to that with the CS Ti top coating(for Ti/Al/Mg system). In addition, CS Ti top coating was in the passivation region in most pH ranges even after 48 h immersion in 3.5 wt% NaCl solution. The stored energy in the CS Ti top coating(as a passive metal) was presumed to be responsible for the easy passivation. Immersion tests indicated no obvious pits formation on the intact CS Ti top coating surface and revealed effective corrosion protection performance of the CS double layered noble barrier coatings on Mg alloys in 3.5 wt% NaCl solution even after 264 h.

Understanding the corrosion of Mg alloys in in vitro urinary tract conditions: A step forward towards a biodegradable metallic ureteral stent

Ureteral stents play a fundamental role in modern time urology. However, following the deployment, stent-related symptoms are frequent and affect patient health and quality of life. Using biodegradable metals as ureteral stent materials have emerged as a promising strategy, mainly due to the improved radial force and slower degradation rate expected. Therefore, this study aimed to characterize different biodegradable metals in urinary tract environment to understand their propensity for future utilization as base materials for ureteral stents. The corrosion of 5 Mg alloys - AZ31, Mg-1Zn, Mg-1Y, pure Mg, and Mg-4Ag - under simulated urinary tract conditions was accessed. The corrosion layer of the different alloys presented common elements, such as Mg(OH)_(2), MgO, and phosphate-containing products, but slight variations in their chemical compositions were detected. The corrosion rate of the different metals varied, which was expected given the differences in the corrosion layers. On top of this, the findings of this study highlighted the significant differences in the samples' corrosion and corrosion layers when in stagnant and flowing conditions. With the results of this study, we concluded that Mg-1Zn and Mg-4Ag presented a higher propensity for localized corrosion, probably due to a less protective corrosion layer;Mg-4Ag corroded faster than all the other four alloys,and Mg-1Y stood out due to its distinct corrosion pattern, that showed to be more homogeneous than all the other four samples, making this one more attractive for the future studies on biodegradable metals.

Quantitative Detection of Corrosion State of Concrete Internal Reinforcement Based on Metal Magnetic Memory

Corrosion can be very harmful to the service life and several properties of reinforced concrete structures.The metal magnetic memory(MMM)method,as a newly developed spontaneous magnetic flux leakage(SMFL)non-destructive testing(NDT)technique,is considered a potentially viable method for detecting corrosion damage in reinforced concrete members.To this end,in this paper,the indoor electrochemical method was employed to accelerate the corrosion of outsourced concrete specimens with different steel bar diameters,and the normal components Bz and its gradient of the SMFL fields on the specimen surfaces were investigated based on the metal magnetic memory(MMM)method.The experimental results showed that the SMFL experimental Bz curves are consistent with the analytical results of the theoretical model.Furthermore,the crest-to-trough behavior on the Bz signal curve and its zero-point gradient spacing can more accurately indicate the corroded area’s extent.Then,a magnetic characteristic parameter W based on a large amount of experimental data was established to characterize the degree of corrosion of the steel bars.The magnetic characteristic parameter W is linearly related to the maximum cross-sectional area loss rate
of the corroded reinforcement.This paper will lay the foundation for future research on corrosion detection of reinforced concrete structures based on the MMM method and provide a feasible way for non-destructive detection of corrosion independent of the influence of reinforcement diameter and magnetization history.

CORROSION MONITORING OF LY12 IN SODIUM CHLORIDE SOLUTION WITH ELECTROCHEMICAL NOISE TECHNIQUE

Spontaneous electrochemical noise (EN) can be a rich source of information concerning the processes simultaneously occurring on a corroding interface. But the noise signal is often difficult to be analyzed due to the complicated nature of the specific systems being investigated. In this paper, the potential noise fluctuations during the free corrosion of commercial aluminum alloy LY12 in sodium chloride solution was recorded and analyzed with different techniques. The typical results showed that the fractal dimension (D,n) obtained from spectral power density (SPD) is mainly directly proportional to the intensity of pitting corrosion and to the value of pitting parameter (SE) derived from dimensional analysis, while the fractal dimension (DE) obtained from EIS is mainly related to the uniform corrosion.

Effect of Sulfate Reduced Bacterium on Corrosion Behavior of 10CrMoAl Steel

The effects of sulfate reduced bacterium （SRB） on the corrosion behavior of 10CrMoAl steel in seawater were studied by chemical immersion, potentiodynamic polarization, electrochemical impedance spectroscopy measurement, and scanning electron microscope techniques. The results show that the content of element sulfur in the corrosion product of 10CrMoAl steel in seawater with SRB is up to 9. 23 %, which is higher than that of the same in sterile seawater. X-ray diffraction demonstrates that the main corrosion product is FeS. SRB increases the corrosion rate by anodic depolarization of the metabolized sulfide product. SEM observation indicates that the corrosion product is not distributed continuously; in addition, bacilliform sulfate-reduced bacterium accumulates on the local surface of 10CrMoAl steel. Hence, SRB enhances sensitivity to the localized corrosion of 10CrMoAl steel in seawater.

Erosion-corrosion and its mitigation on the internal surface of the expansion segment of N80 steel tube

We investigated erosion-corrosion(E-C) and its mitigation on the internal surface of the expansion segment of N80 steel tube in a loop system using array electrode technique, weight-loss measurement, computational-fluid-dynamics simulation, and surface characterization techniques.The results show that high E-C rates can occur at locations where there is a high flow velocity and/or a strong impact from sand particles, which results in different E-C rates at various locations.Consequently, it can be expected that localized corrosion often occurs in such segments.The E-C rate at each location in the expansion segment can be significantly mitigated with an imidazoline derivative inhibitor, as the resulting inhibitor layer significantly impedes the electrochemical reaction rate.However, we found that this inhibitor layer could not effectively reduce the difference in the erosion rates at different locations on the internal surface of the expansion segment.This means that localized corrosion can still occur at the expansion segment despite the presence of the inhibitor.

A New Two-staged Model to Predict Corrosion Degree of Steel Bars in Cracked Concrete Area

In order to quantitatively describe the local corrosion process of steel bars in cracked concrete area, a new two-staged utility model is established, and the effect of transverse cracks on the reinforcement corrosion is analyzed from the angle of long-term service performance evaluation for reinforced concrete structure. Moreover, based on the principle of spectral analysis for environmental action of concrete, an equivalent relationship is established between the corrosion rate in the natural environment and that under the standard temperature and relative humidity condition according to the principle of equivalent annual corrosion depth. Comparison between the inspection results from some references and the calculated values by the two- staged utility model validates the feasibility of the proposed model. The model was applied to Chinese Railway Track System （CRTS） Ⅱ ballastless track slab with transverse dummy joints, from which satisfactory results of corrosion degree of steel bars were obtained.

Local corrosion mechanism of SiO2-based refractories caused by slag movement near solid–liquid–gas interface in different slag systems

Slag movement on SiO2-based prism refractories in different slag systems was observed. The cross section shape evolution mechanism was discussed. Two types of shape evolution appear. For PbO-SiO2 slag whose surface tension improves with SiO2 concentration, slag film flows up along four edges under axial Marangoni shear force and wettability. Then, it flows down along four lateral faces under gravity. Corrosion rate at edges is larger than that on lateral faces due to different SiO2 solubilities of ascending and descending flow. Prism cross section shape changes from square to round. For FetO-SiO2 slag whose surface tension reduces with the increase of SiO2 concentration, slag film flows up under the inflence of wettability. Then, it flows down under Marangoni shear force and gravity. Compared to four edges, slag is mainly up and down on four lateral faces due to larger surface tension and size. So, prism cross section shape keeps square.

Local corrosion characteristics of a graphene-oxide-modified inner coating

Pencil hardness testing,electrochemical impedance spectroscopy,scanning electron microscopy,and scanning Kelvin probe microscopy were used to study the local corrosion characteristics of a graphene-oxide-modified inner coating.The effect of chloride concentration on the corrosion of the damaged inner coating was studied.The effects of chloride ions on damaged internal coatings and graphene-oxide-modified internal coatings were investigated.It was proposed to add graphene oxide into the epoxy coating to effectively inhibit the metal corrosion at the breakage.Because of the existence of graphene oxide(GO),the modified coating had a better physical property and had the effective infiltration of H2O and Cl^- into the coating.The results showed that graphene oxide coatings can give X80 steel better corrosion resistance in sodium chloride solution.

Enhanced localized and uniform corrosion resistances of bulk nanocrystalline 304 stainless steel in high-concentration hydrochloric acid solutions at room temperature

The localized and uniform corrosion resistances of bulk nanocrystalline 304 stainless steel（NC-304 SS）produced by severe rolling technique, and its conventional polycrystalline 304 stainless steel（CC-304 SS）counterpart, were investigated in high-concentration hydrochloric acid solutions at room temperature.NC-304 SS can scarcely suffer from localized corrosion in 4 mol/L and 5 mol/L HCl solutions during 5-day immersion tests, and in 1-3 mol/L HCl solutions during thirty-five-day immersion tests. The corrosion rate of NC-304 SS was also less than that of CC-304 SS during these immersion tests. The improved localized and uniform corrosion resistances of NC-304 SS were explained in terms of the adsorption and chemical activity of Cl;on NC-304 SS and CC-304 SS characterized by X-ray photoelectron spectroscopy,and the valence electron configurations of NC-304 SS and CC-304 SS were characterized by ultra-violet photoelectron spectroscopy rather than conventional electrochemical results.