A complete mathematical model for logarithmic spiral type sprag one-way clutch design and analysis is given.It assumes that the motion of all clutch components can be expressed by a model of epicyclic gearing.It takes...A complete mathematical model for logarithmic spiral type sprag one-way clutch design and analysis is given.It assumes that the motion of all clutch components can be expressed by a model of epicyclic gearing.It takes advantage of Hunt-Crossley contact impact theory to calculate the contact forces between sprags and races,and it can be used for optimization of design and comparison with other types of sprag clutches.A good deal of analysis shows that the parameters of the steady windup angle,the steady contact force,the natural frequency and natural cycle of clutch have nothing to do with the initial velocity of outer race,while the parameters of the maximum transient windup angle,the maximum transient impact force and the steady engagement time increase linearly in the mode of engaging operation of clutch.It is also shown that the strut angle has great influence on the dynamic engagement performance of clutch.The parameters of the steady windup angle,the maximum transient windup angle,the steady engaging time,the steady contact force,the maximum transient impact force and the natural cycle of clutch decrease linearly nearly with the inner strut angle,while the natural frequency of the system increases linearly with the inner strut angle.展开更多
In this study, a modified logarithmic spiral method is proposed to determine the passive earth pressure and failure surface of cohesionless sloping backfill, with presence of wallesoil interface friction. The proposed...In this study, a modified logarithmic spiral method is proposed to determine the passive earth pressure and failure surface of cohesionless sloping backfill, with presence of wallesoil interface friction. The proposed method is based on a limit equilibrium analysis wherein the assumed profile of the backfill failure surface is a composite of logarithmic spiral and its tangent. If the wallesoil interface is smooth, a straight line does not need to be assumed for the failure surface. The geometry of the failure surface is determined using the Mohr circle analysis of the soil. The resultant passive earth thrust is computed considering equilibrium of moments. The passive earth pressure coefficients are calculated with varied values of soil internal friction angle and cohesion, wall friction angle and inclination angle, and sloping backfill angle. This method is verified with the finite element method(FEM) by comparing the horizontal passive earth pressure and failure surface. The results agree well with other solutions, particularly with those obtained by the FEM. The implementation of the present method is efficient. The logarithmic spiral theory is rigorous and self-explanatory for the geotechnical engineer.展开更多
Form milling cutter is built-for-purpose cutter which process the form surface, for example, usually process male and female circular arc face and form trench and so on. From the traditional concept, form milling cutt...Form milling cutter is built-for-purpose cutter which process the form surface, for example, usually process male and female circular arc face and form trench and so on. From the traditional concept, form milling cutter is divided into pointed tooth and relieving follow its structure. Relieving shaped cutter is more convenient than pointed tooth milling cutter, because only its rake face is needed to grind after it turn into blunting, so the current books which are used in college almost select relieving shaped cutter in order to introduce how to design the form milling cutter.The curve of the back of tooth of relieving cutter is the transversal which is formed by the rear face of tooth in the end cut plane of the milling cutter. In the past, because of the limit of the manufacturing technology, the curve of the back of tooth is often selected Archimedes’ curve, in order that the shovel-nose tool acquire the uniform motion when the cutter shovel the back, in other word, the rear face of the milling cutter rotate its axis by the new cutting lip, in the same time, it move uniformly to the axis in order to form the surface. Although this curve of the back of tooth meet the fixedness of the form of blade around grinding the cutter, the rear angle of the dot of the cutting lip don’t keep fixedness. With the development of the modern manufacturing technology, the unmanageable problem of many complex curves is already easily solved. So it is need to study the optimum profile of the curve of the back of tooth in theory, and study the design theory of the relieving shaped cutter under the condition of new manufacture, in order to ensure that the rear angle of the dot of the cutting lip keep fixedness after the relieving shaped cutter is grinded. The paper derive the curve profile of tooth of the form cutter and the modifier calculation formula of the profile of the cutter edge from the definition of the rear angle of the cutter, which establish the foundation for the precision design and manufacture of other form cutter.展开更多
Because of its good condition with mechanics, logarithmic spiral double curve arch bam has been widely used in the practical engineering. The introduction of a new method in how to divide transverse joint in arch dam ...Because of its good condition with mechanics, logarithmic spiral double curve arch bam has been widely used in the practical engineering. The introduction of a new method in how to divide transverse joint in arch dam will be given and the further research of its calculation has been done. The C＋＋ is used in electronic procedure and the 3D simulation has been finished with AutoCAD, which will provide the object model for computer simulation of the arch dam and the division of finite element mesh. Meanwhile, this method in dividing the transverse joint in arch dam also can be taken as the calculated basis for the design and calculation of arch dam, construction lofting and the calculation of the work amount.展开更多
为了解决传统切割刀片滑切角变动幅度大、受力不均、波动较大等问题,该文应用对数螺线方程,设计了藤茎类秸秆专用的等滑切角锯齿型刀片。通过对成熟期番茄藤和茄子藤在不同水分下的切割试验,结果表明:在刀轴转速为4 000 r/min、切割速...为了解决传统切割刀片滑切角变动幅度大、受力不均、波动较大等问题,该文应用对数螺线方程,设计了藤茎类秸秆专用的等滑切角锯齿型刀片。通过对成熟期番茄藤和茄子藤在不同水分下的切割试验,结果表明:在刀轴转速为4 000 r/min、切割速度约为85 m/s的条件下,与普通刀片和等滑切角平型刀片相比,等滑切角锯齿型刀片切割番茄藤和茄子藤的电能分别为0.18和0.25 k W·h,消耗的切割电能少、切割效率高、切割效果好;40°等滑切角锯齿型刀片与45°的相比,40°等滑切角锯齿型刀片切割番茄藤和茄子藤的电能分别为0.38和0.49 k W·h,消耗的切割电能少、切割效率高、切割效果好;材料为Cr12Mo V的等滑切角锯齿型刀片与65Mn的相比,Cr12Mo V的刀片切割番茄藤和茄子藤的电能分别为0.17和0.24 k W·h,切割效果较好。该文设计的刀片在切割过程中受力较均匀,具有降低切割功耗、提高切割效率的作用,对于改进秸秆切割机械的工作性能和减小切割过程的能量消耗具有重要意义。展开更多
基金Project(2011CB706800)supported by the National Basic Research Program of China
文摘A complete mathematical model for logarithmic spiral type sprag one-way clutch design and analysis is given.It assumes that the motion of all clutch components can be expressed by a model of epicyclic gearing.It takes advantage of Hunt-Crossley contact impact theory to calculate the contact forces between sprags and races,and it can be used for optimization of design and comparison with other types of sprag clutches.A good deal of analysis shows that the parameters of the steady windup angle,the steady contact force,the natural frequency and natural cycle of clutch have nothing to do with the initial velocity of outer race,while the parameters of the maximum transient windup angle,the maximum transient impact force and the steady engagement time increase linearly in the mode of engaging operation of clutch.It is also shown that the strut angle has great influence on the dynamic engagement performance of clutch.The parameters of the steady windup angle,the maximum transient windup angle,the steady engaging time,the steady contact force,the maximum transient impact force and the natural cycle of clutch decrease linearly nearly with the inner strut angle,while the natural frequency of the system increases linearly with the inner strut angle.
基金funded by the Doctoral Scientific Research Foundation of Liaoning Province(Grant No.20170520341)the Fundamental Research Funds for the Central Universities(Grant No.N170103015)
文摘In this study, a modified logarithmic spiral method is proposed to determine the passive earth pressure and failure surface of cohesionless sloping backfill, with presence of wallesoil interface friction. The proposed method is based on a limit equilibrium analysis wherein the assumed profile of the backfill failure surface is a composite of logarithmic spiral and its tangent. If the wallesoil interface is smooth, a straight line does not need to be assumed for the failure surface. The geometry of the failure surface is determined using the Mohr circle analysis of the soil. The resultant passive earth thrust is computed considering equilibrium of moments. The passive earth pressure coefficients are calculated with varied values of soil internal friction angle and cohesion, wall friction angle and inclination angle, and sloping backfill angle. This method is verified with the finite element method(FEM) by comparing the horizontal passive earth pressure and failure surface. The results agree well with other solutions, particularly with those obtained by the FEM. The implementation of the present method is efficient. The logarithmic spiral theory is rigorous and self-explanatory for the geotechnical engineer.
文摘Form milling cutter is built-for-purpose cutter which process the form surface, for example, usually process male and female circular arc face and form trench and so on. From the traditional concept, form milling cutter is divided into pointed tooth and relieving follow its structure. Relieving shaped cutter is more convenient than pointed tooth milling cutter, because only its rake face is needed to grind after it turn into blunting, so the current books which are used in college almost select relieving shaped cutter in order to introduce how to design the form milling cutter.The curve of the back of tooth of relieving cutter is the transversal which is formed by the rear face of tooth in the end cut plane of the milling cutter. In the past, because of the limit of the manufacturing technology, the curve of the back of tooth is often selected Archimedes’ curve, in order that the shovel-nose tool acquire the uniform motion when the cutter shovel the back, in other word, the rear face of the milling cutter rotate its axis by the new cutting lip, in the same time, it move uniformly to the axis in order to form the surface. Although this curve of the back of tooth meet the fixedness of the form of blade around grinding the cutter, the rear angle of the dot of the cutting lip don’t keep fixedness. With the development of the modern manufacturing technology, the unmanageable problem of many complex curves is already easily solved. So it is need to study the optimum profile of the curve of the back of tooth in theory, and study the design theory of the relieving shaped cutter under the condition of new manufacture, in order to ensure that the rear angle of the dot of the cutting lip keep fixedness after the relieving shaped cutter is grinded. The paper derive the curve profile of tooth of the form cutter and the modifier calculation formula of the profile of the cutter edge from the definition of the rear angle of the cutter, which establish the foundation for the precision design and manufacture of other form cutter.
基金Supported by Postgraduate education innovation fund of Chongqing Jiaotong University 2010
文摘Because of its good condition with mechanics, logarithmic spiral double curve arch bam has been widely used in the practical engineering. The introduction of a new method in how to divide transverse joint in arch dam will be given and the further research of its calculation has been done. The C＋＋ is used in electronic procedure and the 3D simulation has been finished with AutoCAD, which will provide the object model for computer simulation of the arch dam and the division of finite element mesh. Meanwhile, this method in dividing the transverse joint in arch dam also can be taken as the calculated basis for the design and calculation of arch dam, construction lofting and the calculation of the work amount.
文摘为了解决传统切割刀片滑切角变动幅度大、受力不均、波动较大等问题,该文应用对数螺线方程,设计了藤茎类秸秆专用的等滑切角锯齿型刀片。通过对成熟期番茄藤和茄子藤在不同水分下的切割试验,结果表明:在刀轴转速为4 000 r/min、切割速度约为85 m/s的条件下,与普通刀片和等滑切角平型刀片相比,等滑切角锯齿型刀片切割番茄藤和茄子藤的电能分别为0.18和0.25 k W·h,消耗的切割电能少、切割效率高、切割效果好;40°等滑切角锯齿型刀片与45°的相比,40°等滑切角锯齿型刀片切割番茄藤和茄子藤的电能分别为0.38和0.49 k W·h,消耗的切割电能少、切割效率高、切割效果好;材料为Cr12Mo V的等滑切角锯齿型刀片与65Mn的相比,Cr12Mo V的刀片切割番茄藤和茄子藤的电能分别为0.17和0.24 k W·h,切割效果较好。该文设计的刀片在切割过程中受力较均匀,具有降低切割功耗、提高切割效率的作用,对于改进秸秆切割机械的工作性能和减小切割过程的能量消耗具有重要意义。
