Fault Analysis and Structure Optimization of Traveling Transmission System of Shuttle Car

This paper firstly introduces the common faults of traveling transmission system of shuttle car.Secondly,by analyzing the characteristics of shuttle car structure,the layout of traveling transmission system and the common faults on shuttle car,this paper concludes that"internal holding torque"is the main cause of faults.Finally,this paper proposes a corresponding optimization design scheme to reduce the impact of"internal torque",and calculates the relevant results through the finite element simulation analysis method.Through these analyses and calculations,it is shown that the method can effectively reduce the probability of failure of traveling transmission system of shuttle car.

Generation of structured light beams with polarization variation along arbitrary spatial trajectories using tri-layer metasurfaces

Conventionally,the spatially structured light beams produced by metasurfaces primarily highlight the polarization modulation of the beams propagating along the optical axis or the beams'spatial transmission trajectory.In particular,along the optical axis,the polarization state is either constant or varies continuously in each output plane.Here,we develop innovative spatially structured light beams with continually changing polarization along any arbitrary spatial transmission trajectories.With tri-layer metallic metasurfaces,the geometric characteristics of each layer structure can be adjusted to modulate the phase and polarization state of the incident terahertz(THz)wave.The beam will converge to the predefined trajectory along several paths to generate a Bessel-like beam with longitudinal polarization changes.We demonstrate the versatility of the approach by designing two THz-band structured light beams with varying polarization states along the spatial helical transmission trajectory.Continuous linear polarization changes and linear polarization to right circular polarization(RCP)and back to linear polarization changes are realized respectively.The experimental results are basically consistent with the simulated results.Our proposal for arbitrary trajectory structured light beams with longitudinally varying polarization offers a practical method for continuously regulating the characteristics of spatial structured light beams with non-axial transmission.This technique has potential uses in optical encryption,particle manipulation,and biomedical imaging.

In-phase and out-of-phase spin pumping effects in Py/Ru/Pysynthetic antiferromagnetic structures

The spin pumping effect in magnetic heterostructures and multilayers is a highly effective method for the generationand transmission of spin currents. In the increasingly prominent synthetic antiferromagnetic structures, the two ferromagneticlayers demonstrate in-phase and out-of-phase states, corresponding to acoustic and optical precession modes. Withinthis context, our study explores the spin pumping effect in Py/Ru/Py synthetic antiferromagnetic structures across differentmodes. The heightened magnetic damping resulting from the spin pumping effect in the in-phase state initially decreaseswith increasing Py thickness before stabilizing. Conversely, in the out-of-phase state, the amplified damping exceeds thatof the in-phase state, suggesting a greater spin relaxation within this configuration, which demonstrates sensitivity to alterationsin static exchange interactions. These findings contribute to advancing the application of synthetic antiferromagneticstructures in magnonic devices.

Capturing the non-equilibrium state in light–matter–free-electron interactions through ultrafast transmission electron microscopy

Ultrafast transmission electron microscope(UTEM) with the multimodality of time-resolved diffraction, imaging,and spectroscopy provides a unique platform to reveal the fundamental features associated with the interaction between free electrons and matter. In this review, we summarize the principles, instrumentation, and recent developments of the UTEM and its applications in capturing dynamic processes and non-equilibrium transient states. The combination of the transmission electron microscope with a femtosecond laser via the pump–probe method guarantees the high spatiotemporal resolution, allowing the investigation of the transient process in real, reciprocal and energy spaces. Ultrafast structural dynamics can be studied by diffraction and imaging methods, revealing the coherent acoustic phonon generation and photoinduced phase transition process. In the energy dimension, time-resolved electron energy-loss spectroscopy enables the examination of the intrinsic electronic dynamics of materials, while the photon-induced near-field electron microscopy extends the application of the UTEM to the imaging of optical near fields with high real-space resolution. It is noted that light–free-electron interactions have the ability to shape electron wave packets in both longitudinal and transverse directions, showing the potential application in the generation of attosecond electron pulses and vortex electron beams.

Sound Transmission Loss Analysis of a Double Plate-Acoustic Cavity Coupling System with In-Plane Functionally Graded Materials

In this paper, the isogeometric analysis (IGA) is employed to develop an acoustic radiation model for a double plate-acoustic cavity coupling system, with a focus on analyzing the sound transmission loss (STL). The functionally graded (FG) plate exhibits a different material properties in-plane, and the power-law rule is adopted as the governing principle for material mixing. To validate the harmonic response and demonstrate the accuracy and convergence of the isogeometric modeling, ANASYS is utilized to compare with numerical examples. A plane wave serves as the acoustic excitation, and the Rayleigh integral is applied to discretize the radiated plate. The STL results are compared with the literature, confirming the reliability of the coupling system. Finally, the investigation is conducted to study impact of cavity depth and power-law parameter on the STL.

Strong ground movement induced by mining activities and its effect on power transmission structures

Surface mining activities may introduce damages to nearby infrastructure. Concerns are put forward by the power company about structural integrity of electric power transmission structures in areas where coal mining activities cause strong ground vibrations. Common practice in the power industry is to limit ground motion by specifying maximum Peak Particle Velocity. So far, there is a lack of industry-wide recognized guidelines on how ground vibration limits should be set for the transmission structures. In order to develop a defense strategy to protect power transmission lines against strong ground motions in mining areas, a systematic research work was conducted to establish strong ground vibration characteristics and to study impacts of ground excitations on transmission pole structures. Ground movements were recorded using geophones and wireless tri-axial sensing units. The process of generating ground motion response spectra via analyzing actual ground motion measurements is described in the paper. These spectra developed based on peak particle velocities were used as a basis for spectral analysis performed using validated Finite Element models to obtain structural displacements, reactions and stress states of the transmission pole structures in the mining sites. A quantitative ground motion limit was established by comparing structural responses with the corresponding design requirements.

POWER REFLECTION AND TRANSMISSION IN BEAM STRUCTURES CONTAINING A SEMI-INFINITE CRACK

Wave reflection and transmission in a beam containing a semi-infinite crack are studied analytically based on Timoshenko beam theory., Two kinds of crack surface conditions： non-contact （open） and fully contact （closed） cracks, are considered respectively for an isotropic beam. The analytical solution of reflection and transmission coefficients for a semi-infinite crack is obtained. The power reflection and transmission ratios depend on both the frequency and the position of the crack. Numerical results show the conservation of power transport. The transmitted energy among various wave modes is also investigated. A finite element method is used to verify the validity of the analytical results.

Science Letters:Dual structure of composite right/left-handed transmission line

A dual structure of composite right/left handed (CRLH) transmission line (TL) is analyzed in which an inductance LR is in parallel with a capacitance CL and a shunt capacitance CR is in series with an inductance LL. Both the distributed and lumped cases are considered. The dispersion diagram and transmission properties of the dual CRLH TL are given and compared with those of a standard CRLH TL. Contrary to the frequency response of a standard CRLH TL, a dual CRLH TL has a left-handed (negative phase shift) band at higher frequencies and a right-handed (positive phase shift) band at lower frequencies. A novel dual-band balun is presented as an application.

Analysis of Long-Range Transmission Loss in the West Pacific Ocean

A long-range sound propagation experiment was conducted in the West Pacific Ocean in July 2013. Linear frequency-modulated signals with a frequency band of 260-360Hz were transmitted by a transducer hung on a floating ship during the experiment and were received by a horizontal line array towed by another ship sailing away from the transducer. The maximum distance between the two ships was 1029km. Signals were received at the distances 34-220 kin, 612-635 km and 926-1029 kin. Transmission loss versus distance between source and receiver was obtained and compared with the theoretical results predicted by the parabolic equation method program RAM. It is shown that RAM is adequate for estimating the transmission loss for distances up to 1029km. When the water depth is larger than the surface conjugate depth, the ocean bottom rarely influences the transmission loss in the convergence zones. However, in the opposite situation, the ocean bottom contributes significantly to the transmission loss.

Effect of side transmission of power ultrasonic on structure of AZ81 magnesium alloy

In order to promote the application of power ultrasonic in metallurgic industry, ultrasonic vibration is introduced from the side of AZ81 ingot by adopting the automatic-attracting amplitude transformer horn which has independently been designed and produced, and the effect of the side transmission of ultrasonic on the solidification structure of metal is investigated. The results show that under this experimental condition, power ultrasonic can greatly improve the solidification structure of AZ81 magnesium alloy. Compared with the traditional modification methods in which inoculants are added into melt, power ultrasonic has a better performance. The present research gives us a new way for the application of ultrasonic refinement technique.

A high rectification efficiency Si_(0.14)Ge_(0.72)Sn_(0.14)-Ge_(0.82)Sn_(0.18)-Ge quantum structure n-MOSFET for 2.45 GHz weak energy microwave wireless energy transmission

The design strategy and efficiency optimization of a Ge-based n-type metal-oxide-semiconductor field-effect transistor(n-MOSFET)with a Si_(0.14)Ge_(0.72)Sn_(0.14)-Ge_(0.82)Sn_(0.18)-Ge quantum structure used for 2.45 GHz weak energy microwave wireless energy transmission is reported.The quantum structure combined withδ-doping technology is used to reduce the scattering of the device and improve its electron mobility;at the same time,the generation of surface channels is suppressed by the Si_(0.14)Ge_(0.72)Sn_(0.14) cap layer.By adjusting the threshold voltage of the device to 91 mV,setting the device aspect ratio to 1μm/0.4μm and adopting a novel diode connection method,the rectification efficiency of the device is improved.With simulation by Silvaco TCAD software,good performance is displayed in the transfer and output characteristics.For a simple half-wave rectifier circuit with a load of 1 pf and 20 kΩ,the rectification efficiency of the device can reach 7.14%at an input power of-10 dBm,which is 4.2 times that of a Si MOSFET(with a threshold voltage of 80 mV)under the same conditions;this device shows a better rectification effect than a Si MOSFET in the range of-30 dBm to 6.9 dBm.

Impact of the Opto-Geometric Parameters on the Band Diagram and Transmission and Reflection Spectrum of the Bragg Structure

Knowledge of the band gap and transmission and reflection spectrum of a photonic crystal is essential elements for their design. A graphical interface that quickly determines the banding pattern and spectrum based on the Plane Wave Method (PWM) and coupled modes method (CMM) respectively is created. It is used to explore the behavior of a Bragg structure with the ability to easily vary the important parameters such as refractive indices, number and thickness of layers.

Damage Assessment of Existing Transmission Structures Using ANFIS （Adaptive Neuro-Fuzzy Inference） Model

This paper introduces a new methodology for the damage assessment of existing-transmission structures using six layers, zero order Sugeno model. The model is a hybrid fuzzy-neural system that combines the power of neural networks and fuzzy systems. It is a learning expert system that finds the parameters of the fuzzy sets and fuzzy rules by exploiting approximation techniques from neural networks. The condition ratings of the structural components are determined based on visually observed deterioration-symptoms and the severity of those symptoms. A supervised learning process using training data and expert opinions is used to develop the expert system rules and determine the ratings of the structural components. For the learning from training data, the model uses a combination of least-square estimator and gradient descent method. A sequential least square algorithm is used to determine the weighting factors that minimized the errors. A test case is given to illustrate the power of the proposed fuzzy-neural system. It is concluded that the Sugeno model＇s ability to tune the parameters based on the training data makes it superior to the rules produced by an expert in the conventional fuzzy logic systems.

Optimizing Motheye Nanostructures and Achieving 100% Transmission

Nanostructured Antireflections Layers (NALs) are a promising substitute for conventional antireflection layers. In the nature, such structures have long existed on insects’ eyes. Here, we have derived a general form of mathematical relation that generates a profile close to that of surface of a Moth’s eye. By properly designing NALs over dielectric, light has been efficiently transmitted through our high index nanostructures with minimal reflection. The parameters determining the transmission efficiency are the pitch and the profile of the periodic nanostructures. By optimizing the profile, we have designed NALs with transmission reaching 100%. Our periodic structures have minimal dependence on the pitch. This makes it possible to fabricate NALs with the very broadband transmission, without inducing diffraction to lower wavelengths of the transmitted light. Also, our periodic NALs make it possible to transmit laser lights without scattering.

Investigating the structural effect of electrospun nano-fibrous polymeric films on water vapor transmission

Electrospun polymers have many applications in the industry.However, the structure of these polymers has been less widely considered by researchers.In this work, the structural effect of electrospun and casted films of polyacrylonitrile(PAN) and polyvinylidene fluoride(PVDF) polymers on water vapor transmission were investigated.Sorption of water vapor was measured at 35, 60 and 80 ℃ and different relative humidities.The diffusion coefficients were calculated based on mass changes of the polymer sample.The water vapor transmission rate(WVTR) was also measured at 35 ℃ and 90% relative humidity.The results indicated that electrospun nano-fibrous polymers(ESNPs) absorb much higher water vapor compared to non-porous casted polymers.The interaction of water molecules with mentioned polymers was investigated based on Flory-Huggins theory.The Flory-Huggins interaction parameter of electrospun films was less than casted films, suggesting much better interaction of water molecules with electrospun films.It was also found that electrospun films have anomalous kinetic behavior and do not obey the Fickian diffusion model.Finally, it was revealed that ESNPs show less resistance to water vapor transmission and they are good candidates for the applications of water vapor separation using membranes.

Fault locating for traveling-wave accelerators based on transmission line theory

Radio-frequency(RF)breakdown analysis and location are critical for successful development of high-gradient traveling-wave(TW)accelerators,especially those expected to generate high-intensity,high-power beams.Compared with commonly used schemes involving dedicated devices or complicated techniques,a convenient approach for breakdown locating based on transmission line(TL)theory offers advantages in the typical constant-gradient TW-accelerating structure.To deliver such an approach,an equivalent TL model has been constructed to equate the TW-accelerating structure based on the fun-damental theory of the TL transient response in the time domain.An equivalence relationship between the TW-accelerating structure and the TL model has been established via analytical derivations associated with grid charts and verified by TL circuit simulations.Furthermore,to validate the proposed fault-locating method in practical applications,an elaborate analysis via such a method has been conducted for the recoverable RF-breakdown phenomena observed at an existing prototype of a TW-accelerating-structure-based beam injector constructed at the Huazhong University of Science and Technology.In addition,further considerations and discussion for extending the applications of the proposed method have been given.This breakdown-locating approach involving the transient response in the framework of TL theory can be a conceivable supple-ment to existing methods,facilitating solution to construction problems at an affordable cost.

Structural properties of a-SiO_x:H films studied by an improved infrared-transmission analysis method

An improved method of fitting point-by-point is proposed to determine the absorption coefficient from infrared （IR） transmittance. With no necessity of empirical correction factors, the absorption coefficient can be accurately determined for the films with thin thicknesses. Based on this method, the structural properties of the hydrogenated amorphous silicon oxide materials （a-SiOx：H） are investigated. The oxygen-concentration-dependent variation of the Si-O-Si and the Si-H related modes in a-SiOx：H materials is discussed in detail.

Atomically self-healing of structural defects in monolayer WSe_(2)

Minimizing disorder and defects is crucial for realizing the full potential of two-dimensional transition metal dichalcogenides(TMDs) materials and improving device performance to desired properties. However, the methods in defect controlcurrently face challenges with overly large operational areas and a lack of precision in targeting specific defects. Therefore,we propose a new method for the precise and universal defect healing of TMD materials, integrating real-time imaging withscanning transmission electron microscopy (STEM). This method employs electron beam irradiation to stimulate the diffusionmigration of surface-adsorbed adatoms on TMD materials grown by low-temperature molecular beam epitaxy (MBE),and heal defects within the diffusion range. This approach covers defect repairs ranging from zero-dimensional vacancydefects to two-dimensional grain orientation alignment, demonstrating its universality in terms of the types of samples anddefects. These findings offer insights into the use of atomic-level focused electron beams at appropriate voltages in STEMfor defect healing, providing valuable experience for achieving atomic-level precise fabrication of TMD materials.

Optical transmission through basic-structural-unit superlattices

In this paper, by the transparent-component-decimation （TCD） method we obtain three kinds of new basic- components （BCs） through simplifying and decomposing the BCs of three-component Thue-Morse （3CTM） sequence. Based on these new BCs we propose a type of basic-structural-units （BSUs） and investigate the optical transmission of the one-dimensional （1D） superlattices composed of these BSUs. It is found that if the substrates of the 1D BSU superlattices are certain, the optical transmission at the central wavelength （CW） will be determined completely by the number and the type of BSUs and has nothing to do with the marshalling sequence. In particular, if the substrates are identical, the numbers of different types of BSUs are all the same and the middle two elements of BSUs constitute a cycle, then no matter whether the system is periodic, or quasiperiodic, or aperiodic, or unordered, or even random, it will be transparent at the CW. The conclusion is confirmed by the numerical results. Similar to the even layers of neighbourhood identical elements in TCD method, such a kind of optical BSU subsystem can also be decimated from the chain in the process of transmission investigation. There would be a potential application in the designing of some interesting optical devices.

Asymmetric Price Transmission and Structural Breaks in the Relationship between Costa Rican Markets of Livestock Cattle, Beef and Milk

The vertical price transmission is generally considered as the relationship between two markets of the same production chain However, we can expand this concept to another relation which has not been deeply investigated： the joint products. They are the products which are produced in a single production process, but not correspond to the same chain. An especial case is the beef and milk markets in Costa Rica. Even if these products usually correspond to disconnect chains, in Costa Rica farms make use of cattle to produce both meat and milk. The cointegration framework is applied in order to indentify the price transmission among these markets. In addition, the asymmetric behavior and structural breaks are taken into account. Price transmission between each market pair was found. First, the cattle prices adjust in the milk-cattle relationship, second, beef meat prices adjust in the cattle-beef meat and in the milk - beef meat relationship. Finally, the equations allowing for structural breaks affect the estimates in the following three ways： after the break the elasticities became higher than 1, there is more evidence of cointegration, and the adjustment coefficients are significant only when a change in the long run is allowed.