Cross-section distortion and springback characteristics of double-cavity aluminum profile in force controlled stretch-bending

3D elastic-plastic FE model for simulating the force controlled stretch-bending process of double-cavity aluminum profile was established using hybrid explicit−implicit solvent method.Considering the computational accuracy and efficiency,the optimal choices of numerical parameters and algorithms in FE modelling were determined.The formation mechanisms of cross-section distortion and springback were revealed.The effects of pre-stretching,post-stretching,friction,and the addition of internal fillers on forming quality were investigated.The results show that the stress state of profile in stretch-bending is uniaxial with only a circumferential stress.The stress distribution along the length direction of profile is non-uniform and the maximum tensile stress is located at a certain distance away from the center of profile.As aluminum profile is gradually attached to bending die,the distribution characteristic of cross-section distortion along the length direction of profile changes from V-shape to W-shape.After unloading the forming tools,cross-section distortion decreases obviously due to the stress relaxation,with a maximum distortion difference of 13%before and after unloading.As pre-stretching and post-stretching forces increase,cross-section distortion increases gradually,while springback first decreases and then remains unchanged.With increasing friction between bending die and profile,cross-section distortion slightly decreases,while springback increases.Cross-section distortion decreases by 83%with adding PVC fillers into the cavities of profile,while springback increases by 192.2%.

Performance Analysis of a Profile Control Agent for Waste Drilling Fluid Treatment

A method for the treatment of hazardous waste drilling fluids,potentially leading to environmental pollution,is considered.The waste drilling fluid is treated with an inorganic flocculant,an organic flocculant,and a pH regulator.The profile control agent consists of partially hydrolyzed polyacrylamide,formaldehyde,hexamethylenetetramine,resorcinol,phenol,and the treated waste drilling fluid itself.For a waste drilling fluid concentration of 2500 mg/L,the gelling time of the profile control agent is 25 h,and the gelling strength is 32,000 mPa.s.Compared with the profile control agent prepared by recirculated water under the same conditions,the present profile control agent displays better stability,salt-resistance,and performance.

Optimization of the Plugging Agent Dosage for High Temperature Salt Profile Control in Heavy Oil Reservoirs

After steam discharge in heavy oil reservoirs,the distribution of temperature,pressure,and permeability in different wells becomes irregular.Flow channels can easily be produced,which affect the sweep efficiency of the oil displacement.Previous studies have shown that the salting-out plugging method can effectively block these channels in high-temperature reservoirs,improve the suction profile,and increase oil production.In the present study,the optimal dosage of the plugging agent is determined taking into account connection transmissibility and inter-well volumes.Together with the connectivity model,a water flooding simulation model is introduced.Moreover,a non-gradient stochastic disturbance algorithm is used to obtain the optimal plugging agent dosage,which provides the basis for the high-temperature salting-out plugging agent adjustment in the field.

Optimization of Injection Parameters for Profile Control and Flooding in an Oilfield during High Water Cut Period

In order to improve the effect of water control and oil stabilization during high water cut period, a mathematical model of five point method well group was established with the high water cut well group of an Oilfield as the target area, the variation law of water cut and recovery factor of different injection parameters was analyzed, and the optimization research of injection parameters of polymer enhanced foam flooding was carried out. The results show that the higher the injection rate, the lower the water content curve, and the higher the oil recovery rate. As the foam defoamed when encountering oil, when the injection time was earlier than 80% of water cut, the later the injection time was, the better the oil displacement effect would be. When the injection time was later than 80% of water cut, the later the injection time was, the worse the oil displacement effect would be. The larger the injection volume, the lower the water content curve and the higher the recovery rate. After the injection volume exceeded 0.2 PV, the amplitude of changes in water content and recovery rate slowed down. The optimal injection parameters of profile control agent for high water content well group in Oilfield A were: injection rate of 15 m3/d, injection timing of 80% water content, and injection volume of 0.2 PV.

Research on Optimization Design of Deep Profile Control Injection Scheme in Block S

In view of the rapid decline rate of oil production and gradual increase of water cut in oil wells in Block S, based on the determination of the formula of foam profile control agent, the optimization study of foam profile control injection scheme was carried out. Petrel software is used to establish a facies controlled geological model based on stochastic modeling method in Block S, and CMG software is used for numerical simulation to design 7 sets of foam profile control prediction schemes. Dynamic data and numerical simulation methods are used to optimize foam injection mode and injection cycle. By simulating and calculating, the optimal injection method of alternating gas and liquid injection and the optimal plan with an injection period of 2 months were selected. Through the calculation results of various research plans, it can be seen that the water content of the optimal plan has decreased significantly, and the oil production rate has increased significantly, in order to slow down production decline, control water content rise, extend the economic recovery period of the oilfield, and achieve the goal of improving oil recovery.

Study and Application of a New Association Polymer System for Profile Control

A new polymer system, referred to simply as the AP-P4 polymer system, aims at solving the problems of high temperature, high salinity and the poor shearing resistance, all of which are encountered by conventional polymers (such as polyacrylamide) used in profile control, profile performance improvement and EOR operations in the Zhongyuan Oilfield, Sinopec. This system has been developed on the basis of the specific molecular structure and the better properties of high temperature resistance, high salinity resistance and strong shearing resistance of the new type of AP-P4 association polymer. Acidity modifying agents and cross-linking agents (MZ-YL, MZ-BE, MZ-XS), compatible with the new polymer system, are selected. Results of performance tests have shown that the new polymer system has excellent thickening, high temperature, high salinity and shearing resistance and anti-dehydrating properties. In 2003, it underwent its first pilot test in 26 wells in China, with remarkable effects in increasing oil production and decreasing water production. The newly developed polymer system and its application technology described in this paper may play a guiding role in polymer profile control operations in the oil reservoirs of high temperature and high salinity.

Nonparametric Control Scheme for Monitoring Phase Ⅱ Nonlinear Profiles with Varied Argument Values

Profile monitoring is used to check the stability of the quality of a product over time when the product quality is best represented by a function at each time point.However,most previous monitoring approaches have not considered that the argument values may vary from profile to profile,which is common in practice.A novel nonparametric control scheme based on profile error is proposed for monitoring nonlinear profiles with varied argument values.The proposed scheme uses the metrics of profile error as the statistics to construct the control charts.More details about the design of this nonparametric scheme are also discussed.The monitoring performance of the combined control scheme is compared with that of alternative nonparametric methods via simulation.Simulation studies show that the combined scheme is effective in detecting parameter error and is sensitive to small shifts in the process.In addition,due to the properties of the charting statistics,the out-of-control signal can provide diagnostic information for the users.Finally,the implementation steps of the proposed monitoring scheme are given and applied for monitoring the blade manufacturing process.With the application in blade manufacturing of aircraft engines,the proposed nonparametric control scheme is effective,interpretable,and easy to apply.

PROFILE AND FLATNESS CONTROL SYSTEM IN 1700mm HOT STRIP MILLS OF ANSTEEL

Varying contact-length backup roll and linearly variable crown work roll are provided for improving the mill performance of profile and flatness control. Integrated with theses technologies, relevant profile and flatness control models are developed for hot strip mills on the basis of large amount of finite element calculation. These models include shape setup control model in process control system, bending force feedforward control model, crown feedback control model and flatness feedback control model in basis automation system. Such a profile and flatness control system with full functions is applied in 1 700 mm industrial hot strip mills of Ansteel. Large amount of production data shows that the crown precision with the tolerance of±18 μm is over 90%, the strip percentage which the actual flatness is within ±25 I-unit surpasses 96%, and general roll consume is reduced by 28% by using the profile and fiatness control system. In addition, schedule-free rolling is realized.

Research on Mechanisms of Steam Breakthrough and Profile Control Design for Steam Soaking Well

Scaled physical model tests for steam breakthrough were conducted based on the analysis of mechanisms and influence factors of steam breakthrough. Physical simulation results showed that at the initial steam breakthrough, preferential flow channels were formed in narrow sand packs and most residual oil left in these channels was immobile. This shortened the steam breakthrough time of follow-up steam flooding and decreased the increment of oil recovery efficiency. Steam breakthrough occurred easily for a smaller producer-injector spacing, and a bigger difference in physical properties between fluids and rock. Steam breakthrough is more likely to occur at a larger formation permeability （k）, greater steam displacement velocity （u） and smaller producer-injector spacing （L）. Steam breakthrough time is a function of the parameter group （uk/L）, i.e. tb=3.2151 （uk/L）^-0.5142. A non piston-like displacement model was built based on steam breakthrough observation for a steam stimulated well in the Jinglou Oilfield, Henan Oilfield Company. The steam volume swept in different directions could be obtained from inter-well permeability capacity and breakthrough angle, and the steam swept pore volume （SSPV） was also determined. Numerical simulation showed that steam sweep efficiency reached its peak value when a slug of profile control agent （slug size 10%-15% SSPV） was set at one half of the inter-well spacing. Field test with 12.5% SSPV of profile control agents in the Jinglou Oilfield achieved success in sealing breakthrough channels and good production performance of adjacent producers.

VCR and ASR technology for profile and flatness control in hot strip mills

The roll contour pattern and variety of work and backup rolls in service and its effect on profile and flatness control performance in 1 700 mm hot strip mill at Wuhan Iron and Steel(Group) Corporation were tested and analyzed by the developed finite element models of different typical roll contours configurations.A rather smooth local work roll contour near strip edges and an increase in rolled length can be obtained by application of long stroke work roll shifting system with conventional work roll contours that is incapable of the crown control.In comparison with the conventional backup and work roll contours configuration,the crown control range by the roll bending force enhances by 12.79% and the roll gap stiffness increases by 25.26% with the developed asymmetry self-compensating work rolls(ASR) and varying contact backup rolls(VCR).A better strip profile and flatness quality,an increase in coil numbers within the rolling campaign and a significant alleviated effect of severe work roll wear contours on performance of edge drop control are achieved by the application of ASR with crown control and wear control ability in downstream stand F5 and VCR in all stands of 1 700 mm hot strip mill.

Spatiotemporal phase change materials for thermal energy long-term storage and controllable release

Phase change materials(PCMs)have attracted much attention in the field of solar thermal utilization recently,due to their outstanding thermal energy storage performance.However,PCMs usually release their stored latent heat spontaneously as the temperature below the phase transition temperature,rendering thermal energy storage and release uncontrollable,thus hindering their practical application in time and space.Herein,we developed erythritol/sodium carboxymethylcellulose/tetrasodium ethylenediaminetetraacetate(ERY/CMC/EDTA-4Na)composite PCMs with novel spatiotemporal thermal energy storage properties,defined as spatiotemporal PCMs(STPCMs),which exhibit the capacity of thermal energy long-term storage and controllable release.Our results show that the composite PCMs are unable to lose latent heat due to spontaneous crystallization during cooling,but can controllably release thermal energy through cold crystallization during reheating.The cold-crystallization temperature and enthalpy of composite PCMs can be adjusted by proportional addition of EDTA-4Na to the composite.When the mass fractions of CMC and EDTA-4Na are both 10%,the composite PCMs can exhibit the optical coldcrystallization temperature of 51.7℃ and enthalpy of 178.1 J/g.The supercooled composite PCMs without latent heat release can be maintained at room temperature(10-25℃)for up to more than two months,and subsequently the stored latent heat can be controllably released by means of thermal triggering or heterogeneous nucleation.Our findings provide novel insights into the design and construction of new PCMs with spatiotemporal performance of thermal energy long-term storage and controllable release,and consequently open a new door for the development of advanced solar thermal utilization techniques on the basis of STPCMs.

Dynamics of organic carbon and nitrogen in deep soil profile and crop yields under long-term fertilization in wheat-maize cropping system

Soil organic carbon(SOC)and nitrogen(N)are two of the most important indicators for agricultural productivity.The primary objective of this study was to investigate the changes in SOC and N in the deep soil profile(up to 100 cm)and their relationships with crop productivity under the influence of long-term(since 1990)fertilization in the wheat-maize cropping system.Treatments included CK(control),NP(inorganic N and phosphorus(P)fertilizers),NPK(inorganic N,P and potassium fertilizers),NPKM(NPK plus manure),and M(manure).Crop yield and the properties of topsoil were measured yearly from 2001 to 2009.C and N contents were measured at five different depths in 2001 and 2009.The results showed that wheat and maize yields decreased between 2001 and 2009 under the inorganic fertilizer(NP and NPK)treatments.The average yield between 2001 and 2009 under the NP,NPK,NPKM,and M treatments(compared with the CK treatment)increased by 38,115,383,and 381%,respectively,for wheat and 348,891,2738,and 1845%,respectively,for maize.Different long-term fertilization treatments significantly changed coarse free particulate(cf POC),fine free particulate(ff POC),intramicroaggregate particulate(i POC),and mineral-associated(m SOC)organic carbon fractions.In the experimental years of 2001 and 2009,soil fractions occurred in the following order for all treatments:m SOC>cf POC>i POC>ff POC.All fractions were higher under the manure application treatments than under the inorganic fertilization treatments.Compared to the inorganic fertilization treatments,manure input enhanced the stocks of SOC and total N in the surface layer(0–20 cm)but decreased SOC and N in the deep soil layer(80–100 cm).This reveals the efficiency of manure in increasing yield productivity and decreasing risk of vertical loss of nutrients,especially N,compared to inorganic fertilization treatments.The findings provide opportunities for understanding deep soil C and N dynamics,which could help mitigate climate change impact on agricultural production and maintain soil health.

Morphology and controlling factors of the longitudinal profile of gullies in the Yuanmou dry-hot valley

The morphology of the gully longitudinal profile （GLP） is an important topographic index of the gully bottom associated with the evolution of the gullies. This index can be used to predict the development trend and evaluate the eroded volumes and soil losses by gullying. To depict the morphology of GLP and understand its controlling factors, the Global Positioning System Real-time Kinematic （GPS RTK） and the total station were used to measure the detail points along the gully bottom of 122 gullies at six sites of the Yuanmou dry-hot Valley. Then, nine parameters including length （Lt）, horizontal distance （Dh）, height （H）, vertical erosional area （A）, vertical curvature （Co）, concavity （Ca）, average gradient （Ga）, gully length-gradient index （GL）, normalized gully length-gradient index （Ngl）, were calculated and mapped using CASS, Excel and SPSS. The results showed that this study area is dominated by slightly concave and medium gradient GLPs, and the lithology of most gullies is sandstone and siltstone. Although different types of GLPs appear at different sites, all parameters present a positively skewed distribution. There are relatively strong correlations between several parameters： namely Lt and H, Dh and H, Lt and A, Dh and A, H and GL. Most GLPs, except three, have a best fit of exponential functions with quasi- straight shapes. Soil properties, vegetation coverage, piping erosion and topography are important factors to affect the GLP morphology. This study provides useful insight into the knowledge of GLP morphology and its influential factors that are of critical importance to prevent and control gully erosion.

Researches on the PAM／Cr^3＋ Gel for Deep Profile Control

The profile control hard-gel is composed of polyarylamide (5-6g/L), whose molecular weight is 4,000,000 - 7,000,000 and hydrolysis degree is 17.6%, and cross-linking oxidation-reduction agent (Na2Cr2O7 + NH4Cl), with an delayed organic acid crosslinker which contains lactic acid/propionic acid/ethanoic acid and ethylene glycol. After research of the influence factors, such as pH, temperature, salinity and the dosage of delayed crosslinker, the optimum condition(pH 5.2, temperature 55℃, salinity < 7g/L) was found. Gelation time (12-144h) can be controlled by adjusting the dosage of the delayed crosslinker. Deep profile control experiments are carried out on heterogeneous models, which contains three serial high permeable and low permeable cores arranged in a parallel. After water flooding (total recovery, 24.3%), the first, second and third high-permeable cores each are sealed in turn by the profile control agent, and the total displacement recovery increases to 46.8%, 62.2% and 69.1% respectively. So, the greater the sealed depth, the larger the enhancing recovery will be. Finally, the oil displacement mechanisms of deep profile control are discussed.

The Synthesize and Property Evaluation of High Temperature Resistant Phenolic Resin-Type Profile Control Agent

Most of the mining method of domestic oilfield is waterflood development, thus the water content in the mid and late water flooding would rise faster, and the oil recovery rate would decline relatively more rapid. So it is very important to research profile control agent for stabilizing oil production resin-type profile control agent, and focus on researching the themal stability, shear resistance, gelation time and gelation strength and other properties of this profile control agent?[1]. Finally, the best ratio for synthesizing the high temperature resistant phenolic resin-type profile control agent was obtained.

Injection Scheme Optimization of Foam Profile Control on Block S103

Facing problems with oil production decreasing quickly and water content increasing gradually in S103 well area, the Foam Profile Control was studied on the basis of its confirmed agent formula. The facies-controlled geological model of S103 well area was generated using random model based on Petrel software and using numerical simulation based on CMG software. Gas liquid alternating injection pattern was optimized as the optimal solution through the simulation optimization. Two months are optimized as the optimal solution through the simulation optimization. The cumulative oil production is 0.933 × 107 kg which is higher than the value of subsequent water flooding and the other three. Finally, it reaches the goals of slowing down the production decline and controlling the water rising.

Preparation and performance of fluorescent polyacrylamide microspheres as a profile control and tracer agent

Polyacrylamide microspheres have been suc- cessfully used to reduce water production in reservoirs, but it is impossible to distinguish polyacrylamide microspheres from polyacrylamide that is used to enhance oil recovery and is already present in production fluids. In order to detect polyacrylamide microspheres in the reservoir pro- duced fluid, fluorescent polyacrylamide microspheres P（AM-BA-AMCO）, which fluoresce under ultraviolet irradiation, were synthesized via an inverse suspension polymerization. In order to keep the particle size distribu- tion in a narrow range, the synthesis conditions of the polymerization were studied, including the stirring speed and the concentrations of initiator, NaaCO3, and dispersant. The bonding characteristics of microspheres were deter- mined by Fourier transform infrared spectroscopy. The surface morphology of these microspheres was observed under ultraviolet irradiation with an inverse fluorescence microscope. A laboratory evaluation test showed that the fluorescent polymer microspheres had good water swelling capability, thus they had the ability to plug and migrate in a sand pack. The plugging rate was 99.8 % and the residual resistance coefficient was 800 after microsphere treatment in the sand pack. Furthermore, the fluorescent microspheres and their fragments were accurately detected under ultra- violet irradiation in the produced fluid, even though theyhad experienced extrusion and deformation in the sand pack.

Oil Production Optimization by Means of a Combined“Plugging,Profile Control,and Flooding”Treatment:Analysis of Results Obtained Using Computer Tomography and Nuclear Magnetic Resonance

Due to long-term water injection,often oilfields enter the so-called medium and high water cut stage,and it is difficult to achieve good oil recovery and water reduction through standard methods(single profile control and flooding measures).Therefore,in this study,a novel method based on“plugging,profile control,and flooding”being implemented at the same time is proposed.To assess the performances of this approach,physical simulations,computer tomography,and nuclear magnetic resonance are used.The results show that the combination of a gel plugging agent,a polymer microsphere flooding agent,and a high-efficiency oil displacement agent leads to better results in terms of oil recovery with respect to the situation in which these approaches are used separately(the oil recovery is increased by 15.37%).Computer tomography scan results show that with the combined approach,a larger sweep volume and higher oil washing efficiency are obtained.The remaining oil in the cluster form can be recovered in the middle and low permeability layer,increasing the proportion of the columnar and blind end states of the oil.The nuclear magnetic resonance test results show that the combined“plugging,profile control,and flooding”treatment can also be used to control more effectively the dominant channels of the high permeability layer and further expand the recovery degree of the remaining oil in the pores of different sizes in the middle and low permeability layers.However,for the low permeability layer(permeability difference of 20),the benefits in terms of oil recovery are limited.

Study of Water Treatment Residue Used as a Profile Control Agent

A large amount of residue from the water treatment process has gradually accumulated and thus caused serious environmental pollution in waterflood oilfields. The water treatment residue is a grey suspension, with a density of 1.08 g/cm^3, and mainly contains over 65% of light CaCO3, MgCO3, CaSO4, Fe2S3 and Ca（OH）2. This paper ascertains the effect of water treatment residue on core permeability and its application in oilfields. Coreflooding tests in laboratory were conducted in two artificial cores and one natural core. Core changes were evaluated by cast model image analysis, mercury injection method and scanning electron microscopy （SEM）. Fresh water was injected into another natural core, which was plugged with water treatment residue, to determine the effective life. The results indicate that the water treatment residue has a strongly plugging capability, a resistance to erosion and a long effective life, and thus it can be used as a cheap raw material for profile control. In the past 8 years, a total of 60,164 m^3 of water treatment residue has been used for profile control of 151 well treatments, with a success ratio of 98% and an effective ratio of 83.2%. In the field tests, the profile control agent increased both starting pressure and injection pressure of injectors, and decreased the apparent water injectivity coefficient, significantly improving intake profiles and lengthening average service life of injectors. 28,381 tons of additional oil were recovered from these corresponding oil wells, with economic benefits of ￥3,069.55×10^4 （RMB） and a remarkable input-output ratio of 8.6：1.

Computing Open-Loop Optimal Control of the q-Profile in Ramp-Up Tokamak Plasmas Using the Minimal-Surface Theory

The q-profile control problem in the ramp-up phase of plasma discharges is consid- ered in this work. The magnetic diffusion partial differential equation （PDE） models the dynamics of the poloidal magnetic flux profile, which is used in this work to formulate a PDE-constrained op-timization problem under a quasi-static assumption. The minimum surface theory and constrained numeric optimization are then applied to achieve suboptimal solutions. Since the transient dy- namics is pre-given by the minimum surface theory, then this method can dramatically accelerate the solution process. In order to be robust under external uncertainties in real implementations, PID （proportional-integral-derivative） controllers are used to force the actuators to follow the computational input trajectories. It has the potential to implement in real-time for long time discharges by combining this method with the magnetic equilibrium update.