Multi-layer quasi-zero-stiffness meta-structure for high-efficiency vibration isolation at low frequency

An easily stackable multi-layer quasi-zero-stiffness(ML-QZS)meta-structure is proposed to achieve highly efficient vibration isolation performance at low frequency.First,the distributed shape optimization method is used to design the unit cel,i.e.,the single-layer QZS(SL-QZS)meta-structure.Second,the stiffness feature of the unit cell is investigated and verified through static experiments.Third,the unit cells are stacked one by one along the direction of vibration isolation,and thus the ML-QZS meta-structure is constructed.Fourth,the dynamic modeling of the ML-QZS vibration isolation metastructure is conducted,and the dynamic responses are obtained from the equations of motion,and verified by finite element(FE)simulations.Finally,a prototype of the ML-QZS vibration isolation meta-structure is fabricated by additive manufacturing,and the vibration isolation performance is evaluated experimentally.The results show that the vibration isolation performance substantially enhances when the number of unit cells increases.More importantly,the ML-QZS meta-structure can be easily extended in the direction of vibration isolation when the unit cells are properly stacked.Hence,the ML-FQZS vibration isolation meta-structure should be a fascinating solution for highly efficient vibration isolation performance at low frequency.

Fuzzy-Model-Based Finite Frequency Fault Detection Filtering Design for Two-Dimensional Nonlinear Systems

This article studies the fault detection filtering design problem for Roesser type two-dimensional(2-D)nonlinear systems described by uncertain 2-D Takagi-Sugeno(T-S)fuzzy models.Firstly,fuzzy Lyapunov functions are constructed and the 2-D Fourier transform is exploited,based on which a finite frequency fault detection filtering design method is proposed such that a residual signal is generated with robustness to external disturbances and sensitivity to faults.It has been shown that the utilization of available frequency spectrum information of faults and disturbances makes the proposed filtering design method more general and less conservative compared with a conventional nonfrequency based filtering design approach.Then,with the proposed evaluation function and its threshold,a novel mixed finite frequency H_(∞)/H_(-)fault detection algorithm is developed,based on which the fault can be immediately detected once the evaluation function exceeds the threshold.Finally,it is verified with simulation studies that the proposed method is effective and less conservative than conventional non-frequency and/or common Lyapunov function based filtering design methods.

Precision measurement and suppression of low-frequency noise in a current source with double-resonance alignment magnetometers

Low-noise high-stability current sources have essential applications such as neutron electric dipole moment measurement and high-stability magnetometers. Previous studies mainly focused on frequency noise above 0.1 Hz while less on the low-frequency noise/drift. We use double resonance alignment magnetometers(DRAMs) to measure and suppress the low-frequency noise of a homemade current source(CS) board. The CS board noise level is suppressed by about 10 times in the range of 0.001-0.1 Hz and is reduced to 100 n A/√Hz at 0.001 Hz. The relative stability of CS board can reach2.2 × 10^(-8). In addition, the DRAM shows a better resolution and accuracy than a commercial 7.5-digit multimeter when measuring our homemade CS board. Further, by combining the DRAM with a double resonance orientation magnetometer,we may realize a low-noise CS in the 0.001-1000 Hz range.

A direct laser-synthesized magnetic metamaterial for low-frequency wideband passive microwave absorption

Microwave absorption in radar stealth technology is faced with challenges in terms of its effectiveness in low-frequency regions.Herein,we report a new laser-based method for producing an ultrawideband metamaterial-based microwave absorber with a highly uniform sheet resistance and negative magnetic permeability at resonant frequencies,which results in a wide bandwidth in the L-to S-band.Control of the electrical sheet resistance uniformity has been achieved with less than 5%deviation at 400Ωsq^(-1)and 6%deviation at 120Ωsq^(-1),resulting in a microwave absorption coefficient between 97.2%and 97.7%within a1.56–18.3 GHz bandwidth for incident angles of 0°–40°,and there is no need for providing energy or an electrical power source during the operation.Porous N-and S-doped turbostratic graphene 2D patterns with embedded magnetic nanoparticles were produced simultaneously on a polyethylene terephthalate substrate via laser direct writing.The proposed low-frequency,wideband,wide-incident-angle,and high-electromagnetic-absorption microwave absorber can potentially be used in aviation,electromagnetic interference(EMI)suppression,and 5G applications.

Deformation characteristics and novel strain criteria of strainbursts induced by low-frequency cyclic disturbance

Strainbursts induced by cyclic disturbance with low frequency(termed as cyclicinduced strainbursts)are major dynamic disasters during deep excavation and mining.There is currently no quantitative criterion available for the prediction of such disastrous events.In this study,based on true triaxial experiments,we analyzed the deformation characteristics,established two novel strain criteria for the cyclic-induced strainbursts,and explained the physical meaning of these criteria.Characteristic strains for the cyclic-induced strainbursts were defined,including the control strain ε_(ctr),the strain caused by the combined dynamic and static loading ε_(sd),and the ultimate strain ε_(u) after strainbursts.As indicated by the results,the deformation evolution of the cyclic-induced strainbursts shows remarkable fatigue characteristics,which resemble that of rock subjected to cyclic loading and unloading.In other words,there are three stages during deformation evolution,namely,initial rapid growth,uniform velocity growth after several periods of disturbance,and sudden sharp growth preceding the burst.The ultimate strain ε_(u) is insensitive to the tangential static stress and disturbance amplitude,but it changes nonlinearly with disturbance frequency.From the perspective of deformation,the occurrence of a cyclic-induced strainburst is controlled by the control strainε_(ctr).Thus,a control strain criterion is proposed;that is,when the stain ε_(sd) is larger than the control strain ε_(ctr),a strainburst will be induced by cyclic disturbance.Moreover,based on the statistical results,a strain ratio criterion is proposed;that is,when the strain ratio ε_(sd)/ε_(u) is greater than 30%,a cyclic-induced strainburst will be induced.

TRPV4-induced Neurofilament Injury Contributes to Memory Impairment after High Intensity and Low Frequency Noise Exposures

Objective Exposure to high intensity, low frequency noise(HI-LFN) causes vibroacoustic disease(VAD),with memory deficit as a primary non-auditory symptomatic effect of VAD. However, the underlying mechanism of the memory deficit is unknown. This study aimed to characterize potential mechanisms involving morphological changes of neurons and nerve fibers in the hippocampus, after exposure to HILFN.Methods Adult wild-type and transient receptor potential vanilloid subtype 4 knockout(TRPV4^(-/-)) mice were used for construction of the HI-LFN injury model. The new object recognition task and the Morris water maze test were used to measure the memory of these animals. Hemoxylin and eosin and immunofluorescence staining were used to examine morphological changes of the hippocampus after exposure to HI-LFN.Results The expression of TRPV4 was significantly upregulated in the hippocampus after HI-LFN exposure. Furthermore, memory deficits correlated with lower densities of neurons and neurofilamentpositive nerve fibers in the cornu ammonis 1(CA1) and dentate gyrus(DG) hippocampal areas in wildtype mice. However, TRPV4^(-/-)mice showed better performance in memory tests and more integrated neurofilament-positive nerve fibers in the CA1 and DG areas after HI-LFN exposure.Conclusion TRPV4 up-regulation induced neurofilament positive nerve fiber injury in the hippocampus,which was a possible mechanism for memory impairment and cognitive decline resulting from HI-LFN exposure. Together, these results identified a promising therapeutic target for treating cognitive dysfunction in VAD patients.

Production of super-high strength aluminum alloy billets by low frequency electromagnetic casting

The effects of low frequency electromagnetic field on the macro-physical fields in the semi-continuous casting process of aluminum alloys and the microstructure and crack in the billets were studied and analyzed by the numerical and experimental methods.Comparison of the results for the macro-physical fields in the low frequency electromagnetic casting（LFEC） process with the conventional DC casting process indicates the following characters due to the application of electromagnetic field：an entirely changed direction and remarkably increased velocity of melt flow;a uniform distribution and a decreased gradient of temperature;elevated isothermal lines;a reduced sump depth;decreased stress and plastic deformation.Further,the microstructure of the billets is refined remarkably and the crack in the billets is eliminated in LFEC process because of modification of the macro-physical fields induced by the application of low frequency electromagnetic field.

A wideband low-phase-noise LC VCO for DRM/DAB frequency synthesizer

The wideband CMOS voltage-controlled oscillator（VCO）with low phase noise and low power consumption is presented for a DRM/DAB（digital radio mondiale and digital audio broadcasting）frequency synthesizer.In order to obtain a wide band and a large tuning range,a parallel switched capacitor bank is added in the LC tank.The proposed VCO is implemented in SMIC 0.18-μm RF CMOS technology and the chip area is 750 μm×560 μm,including the test buffer circuit and the pads.Measured results show that the tuning range is 44.6%;i.e.,the frequency turning range is from 2.27 to 3.57 GHz.The measured phase noise is-122.22 dBc/Hz at a 1 MHz offset from the carrier.The maximum power consumption of the core part is 6.16 mW at a 1.8 V power supply.

Nested Miller Active-Capacitor Frequency Compensation for Low-Power Three-Stage Amplifiers

A new frequency compensation technique for low-power, area-efficient multistage amplifiers is introduced. Using nested active capacitors, our scheme achieves better bandwidth-to-power and slew-rate-to-power performances than previous works. Implemented in standard 0.35μm CMOS technology, our three-stage amplifier achieves 105dB DC gain, 3.3M GBW,68 phase margin, and 2.56V/μs average slew rate under a 150pF capacitive load. All of these are realized with only 40μW power consumption under a 2V power supply,with very small compensation capacitors.

The Seasonal Climate and Low Frequency Oscillation in the Simulated Mid-Holocene Megathermal Climate

The mid—Holocene climate about 6000 years ago was simulated by using the atmospheric general circulation model. The orbital parameters for 6 ka BP (before present) were prescribed and other forcing factors were set in the modern conditions. Results show that the large—scale climate change in the African—Asian monsoon areas during the summer—time is strongly compared to the present climate, while the changes in other seasons and regions are generally weak. The results also revealed the change of the low frequency oscillation in the atmosphere. Key words Seasonal climate - Low frequency oscillation - Mid—Holocene This research was jointly supported by the National Natural Science Foundation of China (NSFC) key project “ Variation of Paleo—environment over East Asia and Its Dynamic Relation with the Global Change” under contract 49894170 and the NSFC project “ Coupling of the AGCM with an Biome Model and the Simulation on the Mid-Holocene Climate” under contract 49975018.

Active Low-frequency Vertical Vibration Isolation System for Precision Measurements

Low-fi＇equency vertical vibration isolation systems play important roles in precision measurements to reduce seismic and environmental vibration noise. Several types of active vibration isolation systems have been developed. However, few researches focus on how to optimize the test mass install position in order to improve the vibration transmissibility. An active low-frequency vertical vibration isolation system based on an earlier instrument, the Super Spring, is designed and implemented. The system, which is simple and compact, consists of two stages： a parallelogram-shaped linkage to ensure vertical motion, and a simple spring-mass system. The theoretical analysis of the vibration isolation system is presented, including terms erroneously ignored before. By carefully choosing the mechanical parameters according to the above analysis and using feedback control, the resonance frequency of the system is reduced from 2.3 to 0.03 Hz, a reduction by a factor of more than 75. The vibration isolation system is installed as an inertial reference in an absolute gravimeter, where it improved the scatter of the absolute gravity values by a factor of 5. The experimental results verifies the improved performance of the isolation system, making it particularly suitable for precision experiments. The improved vertical vibration isolation system can be used as a prototype for designing high-performance active vertical isolation systems. An improved theoretical model of this active vibration isolation system with beam-pivot configuration is proposed, providing fundamental guidelines for vibration isolator design and assembling.

EFFECT OF LOW-FREQUENCY ELECTROMAGNETIC FIELD ON THE AS-CASTING MICROSTRUCTURES AND MECHANICAL PROPERTIES OF HDC 2024 ALUMINUM ALLOY

The influences of the low frequency electromagnetic field on the horizontal direct chill casting process were investigated experimentally. Ingots of 2024 aluminum alloy with a cross size of 40 mm× 200 mm were produced by the conventional horizontal chill casting process and low frequency electromagnetic horizontal chill casting processre- spectively. The as-cast structures and the mechanical property of the ingots were examined. The results showed that the low frequency electromagnetic field could sub- stantially refine the microstructures and pronouncedly reduce the macrosegregation in the horizontal direct chill casting process. Moreover, the surface quality of the ingot was prominently improved by the low frequency electromagnetic field. The fracture strength and elongation percentage of the ingot was increased with the low frequency electromagnetic field.

An Investigation on Low Frequency Fatigue Damage of Mooring Lines Applied in a Semi-Submersible Platform

Assessing the fatigue life of mooring systems is important for deep water structures. In this paper, a comprehensive fatigue analysis is conducted on the mooring lines applied in a semi-submersible platform with special focus on the low frequency(LF) fatigue damage. Several influential factors, including water depth, wave spectral parameters, and riser system, are considered. Numerical simulation of a semi-submersible platform with the mooring/riser system is executed under different conditions, and the fatigue damage of mooring lines is assessed by using the time domain analysis method as a benchmark. The effects of these factors on the mooring line tension and the fatigue damage are investigated and discussed in detail. Research results indicate that the LF fatigue damage only accounts for a very small portion of the total damage, although the LF components dominate the global motion response and the mooring line tension of the semi-submersible platform. However, it is demonstrated that the LF fatigue damage is clearly affected by the influential factors. The increase in water depth and spectral peak periods, and the existence of risers can weaken the contribution of the LF components to the mooring line fatigue damage, while the fatigue damage due to the LF components increases with the increase of significant wave height.

Design of multi-layered porous fibrous metals for optimal sound absorption in the low frequency range

We present a design method for calculating and optimizing sound absorption coefficient of multi-layered porous fibrous metals （PFM） in the low frequency range. PFM is simplified as an equivalent idealized sheet with all metallic fibers aligned in one direction and distributed in periodic hexagonal patterns. We use a phenomenological model in the literature to investigate the effects of pore geometrical parameters （fiber diameter and gap） on sound absorption performance. The sound absorption coefficient of multi- layered PFMs is calculated using impedance translation theorem, To demonstrate the validity of the present model, we compare the predicted results with the experimental data. With the average sound absorption （low frequency range） as the objective function and the fiber gaps as the design variables, an optimization method for multi-layered fibrous metals is proposed. A new fibrous layout with given porosity of multi-layered fibrous metals is suggested to achieve optimal low frequency sound absorption. The sound absorption coefficient of the optimal multi-layered fibrous metal is higher than the single- layered fibrous metal, and a significant effect of the fibrous material on sound absorption is found due to the surface Dorosity of the multi-layered fibrous.

Efects of low frequency electromagnetic ield on surface quality, microstructure and hot-tearing tendency of semi-continuous casting ZK60 magnesium alloy billets

The low frequency electromagnetic field was applied during direct chill(DC) semi-continuous casting of the ZK60 magnesium alloy billets. Effects of low frequency electromagnetic field on surface quality, microstructure and hot-tearing tendency of Φ500 mm ZK60 magnesium alloy billets were investigated. The results showed that with the application of the low frequency electromagnetic field, the surface quality of the ZK60 magnesium alloy billets is markedly improved and the depth of cold fold is decreased. The microstructure of the billets is also significantly refined. Besides, the distribution of the grain size is relatively uniform from the billet surface towards its center, where the average grain size is 42 μm at surface and 50 μm at center. It also shows that the hot-tearing tendency of DC semi-continuous casting ZK60 magnesium alloy billets is significantly reduced under low frequency electromagnetic field.

Design of 0.5V low-voltage phase and frequency detector for frequency synthesizer in wireless sensor networks

Based on 0.13μm complementary metal-oxide-semiconductor（CMOS） technology,a phase and frequency detector（PFD） is designed with a low supply voltage of 0.5V for frequency synthesizers used in wireless sensor networks（WSNs）.The PFD can compare the frequency and phase differences of input signals and deliver a signal voltage proportional to the difference.Low threshold transistors are used in the circuits since a power supply of 0.5V is adopted.A pulse latched structure is also used in the circuits in order to increase both the detection range of phase errors and the maximum operation frequency.In experiments,a phase error with a range from-358° to 358° is measured when the input signal frequency is 2MHz.The PFD has a faster acquisition speed compared with conventional digital PFDs.When the input signals are at a frequency of 2MHz with zero phase error,the circuits have a power consumption of 1.8[KG＊8]μW,and the maximum operation frequency is 1.25GHz.

Low-frequency and broadband vibration energy harvester driven by mechanical impact based on layer-separated piezoelectric beam

Vibration energy harvesting is to transform the ambient mechanical energy to electricity. How to reduce the resonance frequency and improve the conversion efficiency is very important. In this paper, a layer-separated piezoelectric cantilever beam is proposed for the vibration energy harvester(VEH) for low-frequency and wide-bandwidth operation, which can transform the mechanical impact energy to electric energy. First,the electromechanical coupling equation is obtained by the Euler-Bernoulli beam theory.Based on the average method, the approximate analytical solution is derived and the voltage response is obtained. Furthermore, the physical prototype is fabricated, and the vibration experiment is conducted to validate the theoretical principle. The experimental results show that the maximum power of 0.445 μW of the layer-separated VEH is about3.11 times higher than that of the non-impact harvester when the excitation acceleration is 0.2 g. The operating frequency bandwidth can be widened by increasing the stiffness of the fundamental layer and decreasing the gap distance of the system. But the increasing of operating frequency bandwidth comes at the cost of reducing peak voltage. The theoretical simulation and the experimental results demonstrate good agreement which indicates that the proposed impact-driving VEH device has advantages for low-frequency and wide-bandwidth. The high performance provides great prospect to scavenge the vibration energy in environment.

Low noise,continuous-wave single-frequency 1.5-μm laser generated by a singly resonant optical parametric oscillator

We report a low noise continuous-wave （CW） single-frequency 1.5-μm laser source obtained by a singly resonant optical parametric oscillator （SRO） based on periodically poled lithium niobate （PPLN）. The SRO was pumped by a CW single-frequency Nd：YVO4 laser at 1.06μm. The 1.02 W of CW single-frequency signal laser at 1.5 μm was obtained at pump power of 6 W. At the output power of around 0.75 W, the power stability was better than ±l.5% and no mode-hopping was observed in 30 min and frequency stability was better than 8.5 MHz in 1 min. The signal wavelength could be tuned from 1.57 to 1.59 μm by varying the PPLN temperature. The 1.5-μm laser exhibits low noise characteristics, the intensity noise of the laser reaches the shot noise limit （SNL） at an analysis frequency of 4 MHz and the phase noise is less than 1 dB above the SNL at analysis frequencies above 10 MHz.

Low-frequency characteristics extension for vibration sensors

Traditional magneto-electric vibration sensors and servo accelerometers have severe shortcomings when used to measure vibration where low frequency components predominate.A low frequency characteristic extension for velocity vibration sensors is presented in this paper.The passive circuit technology,active compensation technology and the closed- cycle pole compensation technology are used to extend the measurable range and to improve low frequency characteristics of sensors.Thses three types of low frequency velocity vibration sensors have been developed and widely adopted in China.

Pressure and velocity cross-spectrum of normal modes in low-frequency acoustic vector field of shallow water and its application

The pressure and horizontal particle velocity combined descriptions in the very low frequency acoustic field of shallow wa- ter integrated with the concept of effective depth of Pekeris wave- guide is proposed, especially the active component of the pressure and horizontal particle velocity cross-spectrum, also called ho- rizontal complex cross acoustic intensity, when only two normal modes are trapped in the waveguide. Both the approximate theo- retic analysis and the numerical results show that the sign of the horizontal complex cross acoustic intensity active component is independent of the range when vertically deployed receiving dual sensors are placed in appropriate depths, the sum of which is equal to the waveguide effective depth, so it can be used to tell whether the sound source is near the surface or underwater; while the range rate is expected to be measured by utilizing the sign distribution characteristic of the reactive component. The further robustness analysis of the depth classification algorithm shows that the existence of shear waves in semi infinite basement and the change of acoustic velocity profiles have few effects on the application of this method, and the seabed attenuation will limit the detection range, but the algorithm still has a good robustness in the valid detection range.