Microstructure and mechanical properties of high-strength low alloy steel by wire and arc additive manufacturing

A high-building multi-directional pipe joint(HBMDPJ)was fabricated by wire and arc additive manufacturing using high-strength low-alloy(HSLA)steel.The microstructure characteristics and transformation were observed and analyzed.The results show that the forming part includes four regions.The solidification zone solidifies as typical columnar crystals from a molten pool.The complete austenitizing zone forms from the solidification zone heated to a temperature greater than 1100℃,and the typical columnar crystals in this zone are difficult to observe.The partial austenitizing zone forms from the completely austenite zone heated between Ac1(austenite transition temperature)and1100℃,which is mainly equiaxed grains.After several thermal cycles,the partial austenitizing zone transforms to the tempering zone,which consistes of fully equiaxed grains.From the solidification zone to the tempering zone,the average grain size decreases from 75 to20μm.The mechanical properties of HBMDPJ satisfies the requirement for the intended application.

Numerical simulation of residual stress and deformation for submerged arc welding of Q690D high strength low alloy steel thick plate

The finite element simulation software SYSWELD is used to numerically simulate the temperature field,residual stress field,and welding deformation of Q690D thick plate multi-layer and multi-pass welding under different welding heat input and groove angles.The simulation results show that as the welding heat input increases,the peak temperature during the welding process is higher,and the residual stress increases,they are all between 330–340 MPa,and the residual stress is concentrated in the area near the weld.The hole-drilling method is used to measure the actual welding residual stress,and the measured data is in good agreement with the simulated value.The type of post-welding deformation is angular deformation,and as the welding heat input increases,the maximum deformation also increases.It shows smaller residual stress and deformation when the groove angle is 40°under the same heat input.In engineering applications,under the premise of guaranteeing welding quality,smaller heat input and 40°groove angle should be used.

Thermal Activation Analyses of Dynamic FractureToughness of High Strength Low Alloy Steels

A formula is derived for determining the influence of temperature and loading rate on dynamic fracture toughness of a high strength low alloy steel (HQ785C) from thermal activation analysis of the experimental results of three-point bend specimens as well as introducing an Arrhenius formula. It is shown that the results obtained by the given formula are in good agreement with the experimental ones in the thermal activation region. The present method is also valuable to describe the relationship between dynamic fracture toughness and temperature and loading rate of other high strength low alloy steels.

Low temperature impact toughness of laser hybrid welded joint of high strength low alloy steel

High strength low alloy steel with 16 mm thickness was welded by using high power laser hybrid welding. Microstrueture was characterized by using optical microscopy, scanning electron microscopy （ SEM ） , transmission electron microscopy （TEM） and selected area electron diffraction （SAED）. Low temperature impact toughness was estimated by using Charpy V-notch impact samples selected from the upper part and the lower part at the same heterogeneous joint. Results show that the low temperature impact absorbed energies of weld metal are （202,180,165 J） of upper samples and （178,145,160 J） of lower samples, respectively. All of them increase compared to base metal. The embrittlement of HAZ does not occur. Weld metal primarily consists of refined carbide free bainite and a little granular bainite since laser hybrid welding owns the character of low heat input. Retained austenite constituent film ＂locates among the lath structure of bainitie ferrite. Refined bainitic ferrite lath and retained austenite constituent film provide better low temperature impact toughness compared to base metal.

The welding application of high strength steels used in engineering machinery

With the rapid development of low alloy steel strength level,more problems caused by welding are exposed day by day.Recently,the efforts have been paid to improve or enchance the low toughness of heated affected zone and welded metal which can enchance the comprehensive mechanical properties that is the core scientific problems of its safe operation by researching crack initiation and crack propragation attracted a rapidly growing interest.This article focuses on the research status and progress of welding technology and joint microstructure and properties of advanced steel materials.The influence of shielding gas on the microstructure evolution of deposited metals,the effect heat input of welded joint performance,interpass temperature and alloy elements on welded joints microstructure and M-A constituent evolution and properties are reviewed in detail.And for the heat affected zone,the grain size and microstructure as well as the shape,size,and distribution of M-A constituent,have a significant impact on the impact toughness.This paper is an attempt to review the effect of different welding process parameters on welded metal and HAZ of HSLA steels.

Effect of Notch Location on Fatigue Life Prediction of Strength Mismatched HSLA Steel Weldments

Welding of high strength low alloy steels (HSLA) involves usage of low, even and high strength filler materials (electrodes) than the parent material depending on the application of the welded structures and the availability of the filler material. In the present investigation, the fatigue crack growth behaviour of weld metal (WM) and heat affected zone (HAZ) regions of under matched (UM), equal matched (EM) and over matched (OM) joints has been studied. The base material used in this investigation is HSLA-80 steel of weldable grade. Shielded metal arc welding (SMAW) process has been used to fabricate the butt joints. Centre cracked tension (CCT) specimen has been used to evaluate the fatigue crack growth behaviour of the welded joints. Fatigue crack growth experiments have been conducted using servo hydraulic controlled fatigue testing machine at constant amplitude loading (R=0).A method has been proposed to predict the fatigue life of HSLA steel welds using fracture mechanics approach by incorporating influences of mismatch ratio (MMR) and notch location.

Correlation of Microstructure Feature with Impact Fracture Behavior in a TMCP Processed High Strength Low Alloy Construction Steel

The present article aims at elucidating the effect of thermo-mechanical controlled processing(TMCP), especially the finish cooling temperature, on microstructure and mechanical properties of high strength low alloy steels for developing superior low temperature toughness construction steel. The microstructural features were characterized by scanning electron microscope equipped with electron backscatter diffraction, and the mechanical behaviors in terms of tensile properties and impact toughness were analyzed in correlation with microstructural evolution. The results showed that the lower finish cooling temperature could lead to a considerable increase in impact toughness for this steel. A mixed microstructure was obtained by TMCP at lower finish cooling temperature, which contained much fine lath-like bainite with dot-shaped M/A constituent and less granular bainite and bainite ferrite. In this case, this steel possesses yield and ultimate tensile strengths of ~ 885 MPa and 1089 MPa, respectively, and a total elongation of ~ 15.3%, while it has a lower yield ratio of ~ 0.81. The superior impact toughness of ~ 89 J at-20 °C was obtained, and this was resulted from the multi-phase microstructure including grain refinement, preferred grain boundaries misorientation, fine lath-like bainite with dot-shaped M/A constituent.

Influence of Ti on Weld Microstructure and Mechanical Properties in Large Heat Input Welding of High Strength Low Alloy Steels

The influence of Ti on weld microstructure and mechanical properties in large heat input welding of high strength low alloy steels is investigated. The results indicate that a moderate amount of Ti is still effective for grain refinement even under larger heat input and a large amount of acicular ferrite （AF） is formed in the weld metal when Ti content is within 0. 028%--0. 038%. With increasing Ti content, proeutectoid ferrite in the weld metal decreases, whereas bainite and M-A constituent increase. The type of inclusion in the welds varies from Mn-Si-AI-O to Ti-Mn- A1-O and finally to Ti-A1-O as Ti content increases from 0 up to 0. 064%. As for adding 0. 028%--0. 038% Ti, high weld toughness could be attained since most inclusions less than 2 tim which contain Ti20s provide the effective nu- clei for aeicular ferrite formation. However, the toughness of the weld metals severely reduces when Ti content is over the optimum ranRe of 0. 028%--0. 038%.

New insights into the mechanism of localised corrosion induced by TiN-containing inclusions in high strength low alloy steel

This work investigated the chemical and electrochemical mechanisms of localised corrosion triggered by CaS·xMgO·y Al_(2)O_(3)·TiN complex inclusions in high strength low alloy steel(HSLAS)under a simulated marine environment.Special focus was given to the role of the TiN portion of the inclusion on the initiation and growth of the corrosion pits.The thermodynamic process of pitting initiation was investigated by Gibbs free energy,Pourbaix diagram and first principle calculation.Localised corrosion is mainly induced by inclusions and triggered by dissolution of adjacent distorted matrix.Chemical dissolution of CaS portion in CaS·xMgO·y Al_(2)O_(3)·TiN complex inclusion creates an acidic aggressive environment that accelerates the further dissolution of inclusion and matrix.Galvanic coupling effect between TiN inclusion and matrix is directly verified.TiN covered with a TiOfilm acts as the cathodic phase in galvanic corrosion,although it has a lower Volta potential than the matrix.This is an unusual correlation with the scanning Kelvin probe force microscopy result,which has been explained for this special system.

Effect of Boron on CGHAZ Microstructure and Toughness of High Strength Low Alloy Steels

Effect of boron on the microstructure and impact toughness in the coarse-grained heat-affected zone（CGHAZ）of two high strength low alloy steels,boron-free and boron-containing,was investigated by means of weld thermal simulation test.The result shows that,for the boron-free steel,a microstructure consisting of grain boundary ferrite degenerates pearlite and granular bainite for longer t8/5（the cooling time from 800 to 500 ℃）,while lath bainite for shorter t8/5.For the boron-containing steel,granular bainite is dominant for a wide range of t8/5.Continuous cooling transformation（CCT）study on the CGHAZ indicates that the transformation start temperature decreases by about 50-100℃under different t8/5,for the boron-containing steel compared with the boron-free steel.The presence of boron suppresses the nucleation of ferrite at prior austenite grain boundaries and hence enlarges the range of t8/5for granular bainite transformation.However,the addition of boron deteriorates the impact toughness of CGHAZ,which may be due to a markedly increased fraction of martensite-austenite（M-A）constituents and decreased fraction of high angle grain boundaries.

New bainite kinetics of high strength low alloy steel in fast cooling process

Based on Kolmgorov-Johnson-Mehl-Avrami analysis, a new bainite kinetics of high strength low alloy steel in fast cooling process was developed by utilizing different experimental methods. Upper bainite transformation morphological evolutions at a cooling rate of 8.3 K/s were directly observed by laser scanning confocal microscopy. This qualitative analysis suggests that bainite packet is more suitable to give a one-dimensional growth model if it is considered as a transformation unit. The nucleation rate of bainite packets in fast cooling process is assumed to give an a priori item. One-dimensional growth model with constant growth rate which is assumed as a function of cooling rate is adopted as well. Thus, the devel- oped new bainite kinetics is simple in expression and contains an adjustable parameter and an empirical pa rameter. Experimental results show upper bainite and lower bainite transformations in fast cooling processes. Their referential phase volume fractions are calculated by the expanded lever rule on the first derivative dilatometer curves. For the similar transformation mechanisms, upper bainite and lower bainite are considered to give the same kinetics. With considering the Nakamura＇s equation, the bainite kinetics is fitted with experimental data. Results show that bainite volume fractions and bainite transformation rates can be expressed precisely bY the newly developed bainite kinetics.

MICROSTRUCTURE AND MECHANICAL PROPERTY DEVELOPMENT IN THE SIMULATED HEAT AFFECTED ZONE OF V TREATED HSLA STEELS

The simulated heat affected zone （HAZ） of the high strength low alloy （HSLA） steels containing 0%, 0.047%, 0.097% and 0.151% vanadium, respectively, were studied with Gleeble-2000 thermomechanical simulator to determine the influence of vanadium addition on the mechanical properties of the HAZ. The HAZ simulation involved reheating the samples to 1350℃, and then cooling to ambient temperature at a cooling rate of 5℃/s ranging from 800 to 500℃ （△8/5=60s）. The mechanical properties including tensile strength and -20℃ impact toughness were conducted. The microstructures of the base steel and the simulated HAZs were investigated using optical microscope, scanning electron microscope （ SEM ） and transmission electron microscope （TEM）. Based on the systemutic examination, the present work confirmed that about 0.05% vanadium addition to low carbon low alloy steels resulted in expected balance of strength and toughness of the HAZ. And more than 0.10% levels addition led to detrimental toughness of the HAZ SEM study showed that the simulated 0.097% and 0.151%V HAZs consisted of more coarse ferrite plates with greater and more M-A constituents along austenite grain and ferrite plate bound- aries. The impact fracture surfaces of the simulated 0.097% and 0.151%V HAZs showed typically brittle mode with predominant cleavages. The size of the facet in the fracture surface increased with increasing vanadium level from 0.097% to 0.151%.As a result, the simulated 0.151% V HAZ has the lowest impact toughness of the four specimens.

Effect of crystallographic orientation on crack growth behaviour of HSLA steel

In this work,the crack growth behaviours of high strength low alloy(HSLA)steel E690 with three crystallographic orientations(the rolling direction,normal direction,and transverse direction)were investigated and compared from the view of the mechano-electrochemical ef-fect at the crack tip.The results show that the crack growth of the HSLA steel is controlled by the corrosion fracture at the crack tip.The vari-ation of crystallographic orientation in E690 steel plate has no influence on the crack tip electrochemical reaction and crack growth mechanism,but changes the crack growth rate.When the stress loading direction is parallel to the rolling direction and the fracture layer is parallel to the transverse-normal plane,the crack growth rate is the slowest with a value of 0.0185 mm·h^(-1).When the load direction and the fracture layer are parallel to the normal direction and the rolling-transverse plane,respectively,the crack growth rate is the highest with a value of 0.0309 mm·h^(-1).This phenomenon is ascribed to the different microstructural and mechanical properties in the rolling direction,normal direction,and transverse direction of E690 steel plate.

Effects of Phosphorus Grain Boundary Segregation and Hardness on the Ductile-to-Brittle Transition for a 2.25CrMo Steel

The combined effect of phosphorus grain boundary segregation and hardness on the ductile-to-brittle transition was examined for a P-doped 2.25CrlMo steel by using Auger electron spectroscopy in conjunction with hardness measurements, Charpy impact tests and scanning electron microscopy. With prolonging time at 540 ~C after water quenching from 980℃, the segregation of phosphorus increases and the hardness decreases. The DBTT （FATT） increases with increasing phosphorus segregation and decreases with decreasing hardness. The effect of phosphorus segregation is dominant until 100 h aging and after that the hardness effect becomes dominant. This effect makes the DBTT （FATT） decrease with further prolonging ageing time although the segregation of phosphorus still increases strongly.

Calculation of AF transformation kinetics in HSLA steel weld

It is of great importance for obtaining the perfect welding properties to control the acicular ferrite (AF) transformation behavior reasonably in steel weld. AF continuous transformation kinetics in the HSLA steel weld was calculated and modeled based on the direct growth on the inclusions inert interface. The simulation results are coincident with the experimental value well.

Image J Analysis of Six Different Annealed Temperatures of 0.17% C of HSLA Steels

Annealing is a heat treatment procedure in which the mechanical properties of a material are being altered, and such alterations cause changes in its properties such as strength and hardness. It is usually carried out to improve ductility and toughness, to reduce hardness and to remove carbides. This study deals with the use of image analysis processing method for the measurement of structure of six annealed samples of 0.17% High Strength Low Alloy (HSLA) Steels (840°C - 990°C) with 30°C interval and 30 minutes soaking time. From the optical microscope images using Image J program, some parameters like calculation of area, pixel value statistics, distances and angles measurements, edge detection, such as the circularity, ferret angle, solidity and perimeter, average area and the percentage area were examined. The annealed sample of 960°C gave the highest grain count of 543 with a perimeter of 41.518;standard deviation 7.057 and a mean of 28.722 which shows that annealing greatly improved the fatigue life of the steel. From the mechanical analysis result, the annealed sample at 840°C has a highest hardness value of 129.4 BHN and gave the lowest impact value of 58.75 J. This study shows a significant decrease in the hardness value as the annealing temperature increased which signifies that annealing temperature enhanced the fatigue property and tensile strength (wear strength) of the steel in study.

A review of friction stir welding of steels： Tool, material flow, microstructure, and properties

Considerable progress has been achieved in friction stir welding （FSW） of steels in every aspect of tool fab- rication, microstructure control and properties evaluation in the past two decades. With the development of reliable welding tools and precise control systems, FSW of steels has reached a new level of technical maturity. High-quality, long welds can be produced in many engineering steels. Compared to traditional fusion welding, FSW exhibits unique advantages producing joints with better properties. As a result of active control of the welding temperature and/or cooling rate, FSW has the capability of fabricating steel joints with excellent toughness and strength. For example, unfavorable phase transformations that usu- ally occur during traditional welding can be avoided and favorable phase fractions in advanced steels can be maintained in the weld zone thus avoiding the typical property degradations associated with fusion welding. If phase transformations do occur during FSW of thick steels, optimization of microstructure and properties can be attained by controlling the heat input and post-weld cooling rate.

Study on the rolling process for thin HSLA heavy plates

Analyzed and studied the characters of high strength low alloy steel which contain Mo,Cr,Nb and Ni.etc.Following actual rolling,combining the feature of rolling mode,and exploiting the equipment advantage of 5 m Heavy Plate Mill,optimized the material design,heating temperature and rolling method, stabilized rolling process of thin alloyed steel,the quality index was advanced.

Effect of pH and applied stress on hydrogen sulfide stress corrosion behavior of HSLA steel based on electrochemical noise analysis

The influence mechanism of pH and the externally applied stress on sulfide stress corrosion cracking behavior based on the joint analysis of the in situ electrochemical noise and microstructure was studied.The results showed that{\mathrm{H}}^{+}in solution changes the composition and structure of corrosion product film by affecting the concentration of{\mathrm{S}}^{2-}and{\mathrm{Fe}}^{2+}near the anode surface.When the pH increased from 2.6 to 3.6 and 4.6,the corrosion product film changed from porous Mackinawite to dense and stable FeS.The change in corrosion product type delayed the crack initiation time by 10.5 and 45.5 h,while the uniform corrosion time was prolonged by 6.1 and 46 h,respectively,delaying SSC behavior.After increasing the applied stress,the local plastic deformation on the material surface increases the porosity and crack rate of the corrosion product film and becomes a fast propagation channel for SSC cracks.When the applied stress is 110%of the actual yield strength of the material,the initiation time of stress corrosion cracking is 6 and 18.1 h earlier than that of 90%and 100%,respectively.The local corrosion time was extended by 23.5 and 8.2 h,respectively,accelerating SSC behavior.

Analysis of cracks origin behaviors during sulfide stress corrosion (SSC) in HSLA steel at different temperatures by electrochemical noise

The sulfide stress corrosion(SSC)behaviors of the high strength low alloy steel at the different temperatures were investigated by the microstructural observation and electrochemical noise(EN)analysis.With the corrosion temperature increasing from 20 to 40℃,SSC ruptured time is prolonged.The increase in corrosion temperature results in the decrease of the saturation solubility of H_(2)S in the solution and thus increases pH value of solution.The increase in corrosion temperature decreases the size of the holes and cracks in the corrosion product film on the surface of the sample,which is due to the formation of the dense FeS corrosion product film.The current kurtosis results indicate that the time for the first occurrence of crack initiation is postponed by the increase in the corrosion temperature.The standard deviation of current noise signals,current kurtosis,power spectral density and energy distribution plot results shows a great consistency,which suggests that EN analysis method can reflect SSC behaviors in real time.