Revealing the key role of non-solvating diluents for fast-charging and low temperature Li-ion batteries

Fast-charging and low temperature operation are of vital importance for the further development of lithium-ion batteries(LIBs),which is hindered by the utilization of conventional carbonate-based electrolytes due to their slow kinetics,narrow operating temperature and voltage range.Herein,an acetonitrile(AN)-based localized high-concentration electrolyte(LHCE)is proposed to retain liquid state and high ionic conductivity at ultra-low temperatures while possessing high oxidation stability.We originally reveal the excellent thermal shielding effect of non-solvating diluent to prevent the aggregation of Li^(+) solvates as temperature drops,maintaining the merits of fast Li transport and facile desolvation as at room temperature,which bestows the graphite electrode with remarkable low temperature performance(264 mA h g^(-1) at-20 C).Remarkably,an extremely high capacity retention of 97%is achieved for high-voltage high-energy graphite||NCM batteries after 250 cycles at-20 C,and a high capacity of 110 mA h g^(-1)(71%of its room-temperature capacity)is retained at-30°C.The study unveils the key role of the non-solvating diluents and provides instructive guidance in designing electrolytes towards fast-charging and low temperature LIBs.

Effect of Low pH on Forming Process of Desulfurization Gypsum Composite Boards Strengthened by Melamine-formaldehyde Resin

Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate ions,favors the longitudinal growth of the crystalline form of the hydration product,which was relatively simple and had the highest length to width(L/D)ratio.At the same time,MF can also improve L/D ratio of gypsum hydration products,which favors the formation of hydrated whiskers.Finally,in a composite system composed of hemihydrate gypsum,MF,and glass fibers,when dilute sulfuric acid was used to regulate pH=3-4,the tight binding formed among the components of the composite system compared to pH=5-6.The hydration product of gypsum adheres tightly to glass fiber surface and produces a good cross-linking and binding effect with MF.The flexural strength,compressive strength,elastic modulus,and water absorption of the desulphurized gypsum composite board is 22.7 MPa,39.8 MPa,5608 MPa,and 1.8%,respectively.

Effective Observation of 518 Cases with Arthralgia－Syndrome treated by High Voltage－Low Frequency Electrotherapy on Acupoints

ＥｆｆｅｃｔｉｖｅＯｂｓｅｒｖａｔｉｏｎｏｆ５１８ＣａｓｅｓｗｉｔｈＡｒｔｈｒａｌｇｉａ－ＳｙｎｄｒｏｍｅｔｒｅａｔｅｄｂｙＨｉｇｈＶｏｌｔａｇｅ－ＬｏｗＦｒｅｑｕｅｎｃｙＥｌｅｃｔｒｏｔｈｅｒａｐｙｏｎＡｃｕｐｏｉｎｔｓ￥ＬｉｕＡｏｓｈｕａｎｇ；Ｈ...

Effects of time lag and stress loading rate on permeability in low permeability reservoirs

In order to study the effect of time lag and stress loading rates on rock deformation,the conventional stepped stress loading mode was changed into a continuous mode to investigate the effect of effective pressure on permeability and porosity.The time lag effect of rock deformation illustrating the relationship between changes in permeability and steady time was studied.Permeability reduction ratios were measured under different stress loading rates which were achieved by different pump rate settings.The results show that permeability and porosity gradually decrease with increases in effective pressure.Permeability at high effective pressure attains stability quickly.Steady times at low effective pressure are very long.Reduction in permeability at lower stress loading rates is small,while,in contrast,it is large at high stress loading rates.

Method for identifying effective carbonate source rocks:a case study from Middle-Upper Ordovician in Tarim Basin,China

Hydrocarbon expulsion occurs only when pore fluid pressure due to hydrocarbon generation in source rock exceeds the force against migration in the adjacent carrier beds.Taking the Middle-Upper Ordovician carbonate source rock of Tarim Basin in China as an example,this paper proposes a method that identifies effective carbonate source rock based on the principles of mass balance.Data from the Well YW2 indicate that the Middle Ordovician Yijianfang Formation contains effective carbonate source rocks with low present-day TOC.Geological and geochemical analysis suggests that the hydrocarbons in the carbonate interval are likely self-generated and retained.Regular steranes from GC-MS analysis of oil extracts in this interval display similar features to those of the crude oil samples in Tabei area,indicating that the crude oil probably was migrated from the effective source rocks.By applying to other wells in the basin,the identified effective carbonate source rocks and non-source rock carbonates can be effectively identified and consistent with the actual exploration results,validating the method.Considering the contribution from the identified effective source rocks with low present-day TOC(TOC_(pd))is considered,the long-standing puzzle between the proved 3 P oil reserves and estimated resources in the basin can be reasonably explained.

Mechanisms for non-ideal flow in low-power arc-heated supersonic nozzles

The flow in a low-powered arc gas heater com- bined with a supersonic nozzle of throat diameter less than 1 mm is quite complicated and difficult to describe in quan- titative detail. Experiments on arc-heated supersonic jet thrusters of monatomic gases argon and helium have been carried out and their performance measured. The flow charac- teristics are analyzed with the help of numerical simulation. Results show that the viscous effect is the most important factor causing the large difference between ideal and real performance. A large outer section of the exit flow is slow- moving. This is especially pronounced in helium, where 70 % of the exit area of the nozzle might be in subsonic flow. Fric- tion forces can be much larger than the net thrust, reaching several times higher in helium, resulting in very low efficien- cies. Other factors causing the differences between ideal and real flow include： complex flow in the throat region, electric arc extending to the nozzle expansion section, heat transfer to the inlet gas and from the hot plasma, and environmen- tal pressure in the vacuum chamber. It is recognized that the ordinary concepts of supersonic nozzle flow must be greatly modified when dealing with such complicated situations. The general concepts presented in this paper could be helpful in guiding the design and operation of this equipment.

Doping effect of cations(Zr^(4+),Al^(3+),and Si^(4+)) on MnO_x/CeO_2 nano-rod catalyst for NH_3-SCR reaction at low temperature

Thermally stable Zr4+, Al3+, and Si4+ cations were incorporated into the lattice of CeO2 nano‐rods (i.e., CeO2‐NR) in order to improve the specific surface area. The undoped and Zr4+, Al3+, and Si4+ doped nano‐rods were used as supports to prepare MnOx/CeO2‐NR, MnOx/CZ‐NR, MnOx/CA‐NR, and MnOx/CS‐NR catalysts, respectively. The prepared supports and catalysts were comprehensively characterized by transmission electron microscopy (TEM), high‐resolution TEM, X‐ray diffraction, Raman and N2‐physisorption analyses, hydrogen temperature‐programmed reduction, ammonia temperature‐programmed desorption, in situ diffuse reflectance infrared Fourier‐transform spectroscopic analysis of the NH3 adsorption, and X‐ray photoelectron spectroscopy. Moreover, the catalytic performance and H2O+SO2 tolerance of these samples were evaluated through NH3‐selective catalytic reduction (NH3‐SCR) in the absence or presence of H2O and SO2. The obtained results show that the MnOx/CS‐NR catalyst exhibits the highest NOx conversion and the lowest N2O concentration, which result from the largest number of oxygen vacancies and acid sites, the highest Mn4+ content, and the lowest redox ability. The MnOx/CS‐NR catalyst also presents excellent resistance to H2O and SO2. All of these phenomena suggest that Si4+ is the optimal dopant for the MnOx/CeO2‐NR catalyst.

Analysis on Impacts and Co-Abatement Effects of Implementing the Low Carbon Cement Standard

Based on the MAP-CGE model,this paper simulated the impacts on the output,energy consumption and pollutant emissions of different cement production processes when implementing a low carbon cement standard in China.It also calculated the impacts on the marginal abatement cost and equilibrium price of the cement industry,and analyzed the co-abatement effects of different pollutants.The results showed that implementing the low carbon cement standard will be beneficial in promoting an upgrading of cement production processes,and strengthening the energy conservation and emission reduction in the cement industry.If there is no change in the existing technology,the cement industry will reduce SO2emissions by 1.17 kg and NOxemissions by 4.44 kg per ton of CO2emission reduction.Implementing low carbon cement standard can also promote NOxabatement in the cement industry.However,the cement industry will bear the abatement costs,and their equilibrium price will increase slightly.

Novel ternary metals-based telluride electrocatalyst with synergistic effects of high valence non-3d metal and oxophilic Te for pH-universal hydrogen evolution reaction

Electrocatalyst designs based on oxophilic foreign atoms are considered a promising approach for developing efficient pH-universal hydrogen evolution reaction(HER)electrocatalysts by overcoming the sluggish alkaline HER kinetics.Here,we design ternary transition metals-based nickel telluride(Mo WNi Te)catalysts consisting of high valence non-3d Mo and W metals and oxophilic Te as a first demonstration of non-precious heterogeneous electrocatalysts following the bifunctional mechanism.The Mo WNi Te showed excellent HER catalytic performance with overpotentials of 72,125,and 182 mV to reach the current densities of 10,100,and 1000 mA cm^(-2),respectively,and the corresponding Tafel slope of 47,52,and 58 mV dec-1in alkaline media,which is much superior to commercial Pt/C.Additionally,the HER performance of Mo WNi Te is well maintained up to 3000 h at the current density of 100 mA cm^(-2).It is further demonstrated that the Mo WNi Te exhibits remarkable HER activities with an overpotential of 45 mV(31 mV)and Tafel slope of 60 mV dec-1(34 mV dec-1)at 10 mA cm^(-2)in neutral(acid)media.The superior HER performance of Mo WNi Te is attributed to the electronic structure modulation,inducing highly active low valence states by the incorporation of high valence non-3d transition metals.It is also attributed to the oxophilic effect of Te,accelerating water dissociation kinetics through a bifunctional catalytic mechanism in alkaline media.Density functional theory calculations further reveal that such synergistic effects lead to reduced free energy for an efficient water dissociation process,resulting in remarkable HER catalytic performances within universal pH environments.

Effects of Hydrogen on Behaviour of Low Cycle Fatigue of 2.25Cr-1Mo Steel

The effects of hydrogen atoms on behaviour of low cycle fatigue of 2.25Cr-1Mo steel have been investigated in present work. The results indicate that the cyclic softening rate and low cycle fatigue life are respectively increased and reduced remarkably by hydrogen atoms. In addition, hydrogen atoms make the original stress amplitude of low cycle fatigue increase, which is because of the drag effect of hydrogen atoms on the moving dislocations. Analyses using electron microscopy show that hydrogen atoms accelerate crack initiation of low cycle fatigue from inclusion and transfer the source of low cycle fatigue crack from the surface of specimen to the inclusion, which results in the marked decrease of low cycle fatigue life. The increase of cyclic softening rate for hydrogen charged specimen is due to hydrogen atoms accelerating the initiating and growing of microvoids from the secondary phase particles in the steel. The reducing of the drag effect of hydrogen atoms on moving dislocations is also helpful to the increase of the cyclic softening rate.

Effect of Cycloheximide on the Adaptive Response Induced by Low Dose Radiation

Human lymphocytes pre-exposed to 10 mGy or 50 mGy of X-rays become less sensitive to subsequent large dose irradiation, exhibited lower rate of chromosome aberration than expected. This adaptive response could be inhibited by cycloheximide, a protein synthesis inhibitor for successive 2 h period ranging from 0.5h before to 4h after the low dose exposure, indicating that the adaptive response was directly related with the protein synthesis.

Effect of Low Dose Radiation on Intracellular Calcium and Protein Kinase C in Lymphocytes

It is first reported in the present paper that whole-body irradiation (WBI) with low dose X-rays could increase intracellular calcium ions ([Ca2+]i) and stimulate protein kinase C (PKC) activity of mouse lymphocytes. Following WBI of male Kunming micc With 75 mGy X-rays at a dose rate of 12.5 mGy/min the mobilization of [Ca2+]i with Con A in CD4+ and CD8+ Cells in the thymus and spleen was potentiated and the amplitude of [Ca2+], mobilization in thymocytes in response to anti-CD3 monoclonal antibody increased with time from 4 to 24 h following low dose radiation. The PKC activity in the homogenate of spleen was markedly stimulated 12 h after WBl with 75 mGy, reaching its peak value at 24-48 h and coming down to lower than normal on day 7. However, the PKC activity in the separated T lymphocytes reached its peak value at 12 h and that in the B lymphocytes reached its peak value on day 4, both coming down to below control on day 7. The implications of this facilitation of signal transduction in T lymphocytes in the mechanism of immunoenhancement after low dose radiation were discussed

Effects of Low Concentrations of Di-(2-ethylhexyl) and Mono-(2-ethylhexyl) Phthalate on Steroidogenesis Pathways and Apoptosis in the Murine Leydig Tumor Cell Line MLTC-1

The aim of this study was to evaluate the effects of low concentrations of DEHP and MEHP on steroidogenesis in a murine Leydig tumor cell line （MLTC-1） in vitro. The result of flow cytometry analysis revealed that the proportion of apoptotic cells was significantly increased after the exposure to DEHP. All three genes （P450scc, P450c17, and 38HSD） under study showed an increased expression following exposure to DEHP or MEHP, although some insignificant inhibitory effects appeared in the 10μmol/L treatment group as compared with the controls. It was also found that DEHP or MEHP stimulated INSL3 mRNA and protein especially in the 0.001 μmol/L treatment group. Testosterone secretions were stimulated after the exposure to DEHP or MEHP. Alterations of steroidogenic enzymes and INSL3 in MLTC-1 cells might be involved in the biphasic effects of DEHP/MEHP on androgen production.

Study on the Antitumor Effects of Low-energy Laser Irradiation Combined with Cyclophosphamide

Systematic experiments about the antitumor effects of low energy laser irradiation combined with the traditional antitumor medicine of cyclophosphamide were conducted using the experimental model of mouse S180 ascites sarcoma.The three groups of tumor bearing mice were irradiated upon the inner corners with the dosages of 11 00,14 67 and 22 00 J·cm -2 LELI respectively,and injected with CYT intraperitoneally to observe the changes of the survival time,the ascites growth speed,and the kinetic changes of immune functions.The survival times of the three groups of CYT/LELI combination were obviously longer than those of the tumor and CYT control groups.Correspondingly,the amounts of ascites,tumor cells densities and total tumor cells in CYT/LELI groups decreased significantly,while the death ratio of the tumor cells increased.Comparatively,the group of 22 00 J·cm -2 LELI combined with CYT showed the most ideal antitumor effects,and the life prolongation ratio was up to 53 20%.

Effects of Low-Power Microwave Fields on Seed Germination and Growth Rate

Experiments were conducted to investigate the effects of low power microwave radiation on germination and growth rate in seeds. In the present paper, the bioeffects of low power (non-thermal intensity) microwave modulated with 1 KHz square wave have been studied. Experiments were performed in X-band frequencies using klystron based microwave test bench. Microwave parameters like frequency, power, exposure time and power density were varied while irradiating seed samples to study their influence on germination. The seed samples used for the experiment included wheat (Triticum aestivum), bengal gram (Cicer arietinum), green gram (Vigna radiate) and moth bean (Vigna Aconitifolia). Seed germination %, plant height, root length and dry matter % (biomass %) were recorded and compared with control seeds. The effects of different treatments were found to be stimulating the germination and seedling vigour of plants especially in power and exposure time treatments while increase in frequency and power density has reduced the seed germination and seedling vigour. The effect also varied with the nature of seeds.

An Improved SOI CMOS Technology Based Circuit Technique for Effective Reduction of Standby Subthreshold Leakage

Silicon-on-insulator (SOI) CMOS technology is a very attractive option for implementing digital integrated circuits for low power applications. This paper presents migration of standby subthreshold leakage control technique from a bulk CMOS to SOI CMOS technology. An improved SOI CMOS technology based circuit technique for effective reduction of standby subthreshold leakage power dissipation is proposed in this paper. The proposed technique is validated through design and simulation of a one-bit full adder circuit at a temperature of 27℃, supply voltage, VDD of 0.90 V in 120 nm SOI CMOS technology. Existing standby subthreshold leakage control techniques in CMOS bulk technology are compared with the proposed technique in SOI CMOS technology. Both the proposed and existing techniques are also implemented in SOI CMOS technology and compared. Reduction in standby subthreshold leakage power dissipation by reduction factors of 54x and 45x foraone-bit full adder circuit was achieved using our proposed SOI CMOS technology based circuit technique in comparison with existing techniques such as MTCMOS technique and SCCMOS technique respectively in CMOS bulk technology. Dynamic power dissipation was also reduced significantly by using this proposed SOI CMOS technology based circuit technique. Standby subthreshold leakage power dissipation and dynamic power dissipation were also reduced significantly using the proposed circuit technique in comparison with other existing techniques, when all circuit techniques were implemented in SOI CMOS technology. All simulations were performed using Microwindver 3.1 EDA tool.

Electron-beam radiation effects on the structure and properties of polypropylene at low dose rates

While the high-energy radiation effects on polypropylene, which are crucial for the cable industry for nuclear power plants, have been thoroughly studied, the property changes of PP at low-dose-rate electron-beam irradiation are far from elucidated. Herein, the influence of electron-beam irradiation on the structure and properties of PP was examined. The static EB irradiation conditions were 1.2 MeV at a low dose rate of 20 kGy/h to achieve absorbed doses ranging from 45, to 60, 100, and 200 kGy.The molecular structure was first evaluated by measuring the carboxyl index and the relative radical concentrations via Fourier transform infrared spectroscopy and electron spin resonance, respectively. Mechanical, differential scanning colorimetric, and rheological tests were carried out to further investigate the changes in the properties(tensile, crystalizing, and viscoelastic properties) of irradiated PP, which showed good agreement with the structural analysis results. We found that radio-oxidative degradation(chain scission) was predominant, which can be due to the low dose rate facilitating oxygen diffusion into the PP matrix during electron-beam irradiation.

Alkyl dimethyl betaine activates the low-temperature collection capacity of sodium oleate for scheelite

The impact of alkyl dimethyl betaine (ADB) on the collection capacity of sodium oleate (NaOl) at low temperatures was evaluated using flotation tests at various scales. The low-temperature synergistic mechanism of ADB and NaOl was explored by infrared spectroscopy, X-ray photoelectron spectroscopy, surface tension measurement, foam performance test, and flotation reagent size measurement.The flotation tests revealed that the collector mixed with octadecyl dimethyl betaine (ODB) and NaOl in a mass ratio of 4:96 exhibited the highest collection capacity. The combined collector could increase the scheelite recovery by 3.48% at low temperatures of 8–12℃. This is particularly relevant in the Luanchuan area, which has the largest scheelite concentrate output in China. The results confirmed that ODB enhanced the collection capability of NaOl by improving the dispersion and foaming performance. Betaine can be introduced as an additive to NaOl to improve the recovery of scheelite at low temperatures.

Time and Dose-related Effects of the Pyrethroid Fluvalinate on Haemolymph Carbohydrates and Gut Lipids of Honeybees,Following in vivo Injection of very Low Doses

The injection to emerging adult workerbees with fluvalinate doses ranging from 1 femtomol to 1 nanomol per individual resulted in a reduction of haemolymph carbohydrate concentrations, particularly at the lowest dose 1 hour after injections. At the same time, a large increase was observed for triacylglycerols and to a much lesser extent for steroids and phospholipids with 0.1 picomol per bee. By contrast, fatty acids, steroids and triacylglycerols exhibited a depress at the higher dose. Most responses were thus biphasic, showing that much attention should be paid to the effects of very low doses of pesticide.