Precision measurement and suppression of low-frequency noise in a current source with double-resonance alignment magnetometers

Low-noise high-stability current sources have essential applications such as neutron electric dipole moment measurement and high-stability magnetometers. Previous studies mainly focused on frequency noise above 0.1 Hz while less on the low-frequency noise/drift. We use double resonance alignment magnetometers(DRAMs) to measure and suppress the low-frequency noise of a homemade current source(CS) board. The CS board noise level is suppressed by about 10 times in the range of 0.001-0.1 Hz and is reduced to 100 n A/√Hz at 0.001 Hz. The relative stability of CS board can reach2.2 × 10^(-8). In addition, the DRAM shows a better resolution and accuracy than a commercial 7.5-digit multimeter when measuring our homemade CS board. Further, by combining the DRAM with a double resonance orientation magnetometer,we may realize a low-noise CS in the 0.001-1000 Hz range.

Simultaneous Measurements of Rainfall Intensity, Low Energy Neutrons and Gamma Radiation in Sao Jose Dos Campos, SP, Brazil

The article aims to study the possible correlation between the presence and intensity of rainfall X- and T-radiation and low energy neutrons at one specific location in S[io Jos6 dos Campos, SP, Brazil. Monitoring of these parameters was carried out from end February to half of June 2013 just in Physics Department of ITA （Technological Institute of Aeronautics）. By correlating the data of measurements of intensity of X and ）,-radiations with the rainfall it has been found that this meteorological parameter had a significant influence on the background of these radiation profile. A possible reason for this fact is associated with the presence of radon gas in the environment that is dragged to the surface during the occurrences of local rainfall. In relation neutrons, it was possible to note that the rainfall has small influence on this parameter measures.

Comparative Analysis on Two Kinds of Measurement Methods of Particulate Matters in Waste Gas of Low Velocity

In the current waste gas sampling of fixed source,it is required that deviation of tracking rate of constant velocity sampling should not be more than 10%.When flow rate of the waste gas is less than 5 m/s,the tracking rate can not meet this requirement.The sampling of fixed velocity can meet the requirement of particulate matter sampling on gas collection volume at low velocity.Through the comparison of two different methods for the determination of particulate matter in waste gas under the low flow velocity of flue gas,it was found that there were some differences between the fixed velocity measurement and the constant velocity measurement.The results showed that measurement result of the fixed velocity was higher than that of constant velocity measurement under low velocity.At the same time,the deviation of fixed velocity measurement was not obvious under different low velocity.

Study on signal intensity of low field nuclear magnetic resonance via an indirect coupling measurement

We carry out an ultra-low-field nuclear magnetic resonance （NMR） experiment based on high-T c superconducting quantum interference devices （SQUIDs）. The measurement field is in a micro-tesla range （～10 μT-100 μT） and the experiment is conducted in a home-made magnetically-shielded-room （MSR）. The measurements are performed by the indirect coupling method in which the signal of nuclei precession is indirectly coupled to the SQUID through a tuned copper coil transformer. In such an arrangement, the interferences of applied measurement and polarization field to the SQUID sensor are avoided and the performance of the SQUID is not destroyed. In order to compare the detection sensitivity obtained by using the SQUID with that achieved using a conventional low-noise-amplifier, we perform the measurements using a commercial room temperature amplifier. The results show that in a wide frequency range （～1 kHz-10 kHz） the measurements with the SQUID sensor exhibit a higher signal-to-noise ratio. Further, we discuss the dependence of NMR peak magnitude on measurement frequency. We attribute the reduction of the peak magnitude at high frequency to the increased field inhomogeneity as the measurement field increases. This is verified by compensating the field gradient using three sets of gradient coils.

Anthropometric measurements at birth as predictor of low birth weight

In developing countries, low birth weight (BW < 2500 grams) accounts for 60% - 80% of neonatal deaths. Early identification and referral of LBW babies for extra essential newborn care is vital in preventing neonatal deaths. Studies carried out in different populations have suggested that the use of newborn anthropometric surrogates of birth weight may be a simple and reliable method to identify LBW babies. previous studies reported correlation between birth weight to several anthropometric measurements and their predictive value. We aimed to evaluate the correlation between birth length, head, chest, and mid arm circumferences to birth weight. Methods: A cross sectional study has been conducted in SHARIATI Hospital in Tehran, from September 2008 to February 2009. All Consecutive full-term. Single ton, live born babies were included and anthropometric measurements carried out within 48 hours after birth by authors. Birth weight was measured by digital scale within the first 24 hours after delivery. Birth length by somatometer and head, chest, mid arm circumferences were measured 2 times by using plastic measuring tape. Result: Out of 500 newborn studied. 52.2% were male and 47.8% were female. The mean birth weight was 3195.4 ± 399.9 gram and 3.8% of newborns were low birth weight. It was evident a positive correlation of birth weight to all such anthropometric measurements with the highest correlation coefficient for chest circumference (r: 0.74). By ROC- AUC analyses, chest circumference (AUC = 0.91, 95% CI 0.84 to 0.97) and arm circumference (AUC = 0.87, 95% CI 0.79 to 0.95) were identified as the optimal surrogate indicators of LBW babies. The optimal cut-points for chest circumference and arm circumference to identify LBW newborns were ≥31.2 cm and ≥10.2 cm respectively. Conclusions: Chest and mid arm circumferences were the best anthropometric surrogates of LBW among studied Iranian population. Further studies are needed in the field to cross-validate our results. anthropometric values are simple, practicable, quick and reliable indicator for predicting LBW newborns in the community and can be easily measured by paramedical workers in developing nation.

Model and methods for comprehensive measurement of the low-carbon status of China's oil and gas enterprises

This paper establishes a model that would allow China＇s oil and gas enterprises to scientifically evaluate and measure their low-carbon level and status. It considers various characteristics of China＇s oil and gas enterprises and the implications of low-carbon development, and is based on an overall analysis of factors that influence the reduction of carbon emissions. In view of low-carbon economic theories and the general principles of an evaluation index system, a comprehensive system for measuring the low-carbon status of China＇s oil and gas enterprises has been developed. This measurement system is comprised of four main criteria （energy structure, energy utilization, carbon emissions and utilization, and low carbon management） as well as thirty indexes. By the Delphi method and the analytical hierarchy process （AHP）, the weight of the rules hierarchy and indexes hierarchy were determined. The standardized indexes were then integrated using a linear weighted sum formula, and a comprehensive formula for index measurement was established. Taking into account the status of low- carbon development in the petroleum and petrochemical industry at home and abroad, an evaluation criterion is proposed comprising four levels： ideal low-carbon, economical low-carbon, medium-carbon and high-carbon, whose values were organized within the settings of [0, 1].

Instantaneous Creep in Face-centered Cubic Metals at Ultra- low Strain Rates by a High-resolution Strain Measurement

Instantaneous creep in face-centered cubic metals, 5N Al（99.999%）, 2N Al （99%） and 4N Cu （99.99%） with different grain sizes, was firstly investigated by sudden stress-change experiments at ultra- low strain rates ε ≤10-10 s-1 and temperature T 〈 0.32 Tn. The experimental results indicate that the observed instantaneous creep is strongly dependent on grain size, the concentration of impurity, and stacking fault energy. Creep in high-purity aluminum, 5N Al, with a very large grain size, d 〉 1600μm, shows non-viscous behavior, and is controlled by the recovery of dislocations in the boundary of dislocation cells. On the other hand, for 5N A1 with a small grain size, d=30μm, and low-purity aluminum, 2N A1, with d8= 25μm, creep shows viscous behavior and may be related to ＇low temperature grain boundary sliding＇. For high-purity copper, 4N Cu, with d= 40 grn and lower stacking fault energy, creep shows a non-viscous behavior, and is controlled by the recovery process of dislocations. For all of the samples, creep shows anelastic behavior.

ERROR COMPENSATION OF COORDINATE MEASURING MACHINES WITH LOW STIFFNESS

A technique for compensating the errors of coordinate measuring machines (CMMs) with low stiffness is proposed. Some additional items related with the force deformation are introduced to the error compensation aquations. The research was carried on a moving colunm horizontal arm CMM. Experimental results show that both the effects of systematic components of error motions and force deformations are greatly reduced, which shows the effectiveness of proposed technique.

Dynamic Monitoring and Control Measures of Spodoptera frugiperda(J.E.Smmith) in Low Latitude Plateau Sugarcane Areas

Spodoptera frugiperda (J.E.Smmith) is one of the major migratory pests warned by the Food and Agriculture Organization (FAO).It has been successfully invaded sugarcane and corn in Jinggu,Longchuan,Gengma,Menghai,Yingjiang,Lancang of Yunan Province,China.In view of the great variety of hosts,wide range of habitats and strong migration ability,S.frugiperda has the potential of causing catastrophic threats to sugarcane production.In this paper,we made a systematic introduction to the morphological and biological characteristics of S.frugiperda,analyzed its occurrence situations and occurrence trends in Yunnan of China and other countries around the world,and proposed the control strategies and measures of ecological regulation and control,natural enemies protection and utilization,biological control,pesticide control and adults trapping based on the outbreak characteristics of S.frugiperda and the actual sugarcane production in low latitude plateau areas.

The Preliminary Study on the Converting Measures between the Four Waters in Wet and Low-lying Farmland

Most of China's wetland areas are located in the Sanjiang Plain.This area has 207×10 4 hm 2 of wet and low lying farmland,of which 59% is cropped.During the 1970s and 1980s,the Chinese government organized intensive scientific research into potential changes to existing natural resources conditions for these farmlands.The aim was to change the water resources regime to one that was beneficial to crop production.Arterial drainage,field drainage and appropriate sub soil treatments were required.The relation between plant products industry and the Four Waters distribution,also the main measures of the Four Waters converting in wet and low lying farmland were discussed in the paper.

Factors Influencing the Use of Outcome Measures for Patients with Low Back Pain: A Survey of Nigerian Physiotherapists

Background: Low back pain is one of the important patients’ presenting complain that requires expert management from the physiotherapists. Yet no work was available for reference on the use of outcome measures for its evaluation by Nigeria physiotherapists. Objective: This study, therefore, investigated the outcome measures used by Nigerian physiotherapists to evaluate patients with Low Back Pain and the factors that influenced their use. Methods: A survey questionnaire was posted to 306 randomly selected mem- bers of the Nigeria Society of Physiotherapy (NSP). Data were analyzed using frequency, percentages, mean, ANOVA, and Pearson’s Chi-square. P-value was placed at 0.05. Results: 52.9% of the respondents (221) used a pain visual analog scale. Only 36.1% used LBP-specific clinical outcome measures. The factors that influenced their use were belief, attitude, knowledge, and choice. There was no significant difference between the majority of the factors and the use of clinical outcome measures. The P-values were 0.960, 0.648, 0.760 for belief, attitude and knowledge respectively. The only factor that had a significant difference (P = 0.029) with the use of clinical outcome measures was choice. Gender and postgraduate qualification had no significant influ- ence on the use of clinical outcome measures at the P-value of 0.117 and 0.510 respectively. Conclusion: Pain visual analog scale is the outcome measure frequently used by Nigeria Physiotherapists to evaluate patients with Low Back Pain. Belief, attitude, knowledge, and choice are the factors that influ- enced the use. There is a need to incorporate the use of LBP-specific outcome measures by Nigerian physiotherapists while treating patients with LBP.

Polypyrrole Chitosan Cobalt Ferrite Nanoparticles Composite Layer for Measuring the Low Concentration of Fluorene Using Surface Plasmon Resonance

Fluorene is a polycyclic aromatic hydrocarbon, which is a hazardous toxic chemical in the environment. The measurement of low concentrations of fluorene is a subject of intense interest in chemistry and in the environment. Polypyrrole chitosan cobalt ferrite nanoparticles are prepared using the electrochemical method. The prepared layers are characterized using field emission scanning electron microscopy, Fourier transform infrared spectroscopy, and energy dispersive spectroscopy. The layers are used to detect fluorene using the surface plasmon resonance technique at room temperature. The composite layer is evaluated after detection of fluorene using atomic force microscopy. The fluorene is bound on the layer, and the shift of the resonance angle is about 0.0052°, corresponding to the limitation of 0.01 ppm.

The Measuring and Impacting Factors Analysis of Rural Straw Yield-Based on the Perspective of Constructing Low-carbon Agricultural Economy

On the basis of expounding the status quo and using developmental trend of China's straw,4 indices are selected:straw yield,planting area,using amount of fertilizer and effective irrigation area.According to the relevant data of China Statistical Yearbook from 1991 to 2008,by using linear regression model,we calculate China's rural straw yield,analyze the factors impacting straw yield,and point out that the using amount of fertilizer is the important factor impacting straw yield.Based on these,in the perspective of low-carbon agricultural economy,we put forward suggestions of using straw comprehensively from 4 perspectives in order to provide theoretical reference for decision-makers:improve fertilizer dependence;develop straw reuse technology;popularize the technology of straw gasification actively;strengthen farmers' low-carbon awareness.

Low temperature cracking behavior of asphalt binders and mixtures: A review

Low temperature cracking(LTC)distress on pavement seriously affects road life.This paper finished a literature review of the research on the mechanism of LTC of asphalt composites(asphalt composites refers to asphalt binder and asphalt mixture in this article),test methods,factors contributing to LTC,measures to prevent and control the distress,and prediction of LTC in asphalt pavements.The following conclusions were obtained:the cracking mechanism of asphalt mixtures needs to be further revealed by means of simulation at the micro level,the BBR and 4 mm plate test(by DSR)methods are currently optimal,and a correlation between asphalt and asphalt mixture evaluation indexes needs to be established.Sensitivity analyses are needed for the factors affecting LTC of asphalt mixtures.It is necessary to calculate the contribution of each factor to the LTC of asphalt mixtures.The aim is to propose targeted improvement measures for the most unfavourable factors,as well as to carry out research and development of key materials for anti-cracking.Measures for the prevention and control of LTC of asphalt pavement are analyzed and discussed.Existing researches on the prediction of LTC of asphalt pavements is discussed.It is necessary to analyse the mechanical response of asphalt pavement,the damage process and the sensitivity of anti-cracking parameters on the basis of considering the complex geometrical characteristics and material properties of asphalt pavement materials.Finally,the mechanism of LTC,evaluation methods,factors influencing LTC,and remedial measures for asphalt composites were summarized,and future research prospects were suggested.This paper provides theoretical support for the further solution of LTC distress of asphalt pavement,which is effective on the improvement of pavement life.

Actuality and Improvement Measures of Mediumand Low-yielding Farmland in Liaoning Province

In order to improve the quality of cultivated land in Liaoning Province in the light of local conditions, medium- and low-yielding farmland in Liaoning Province are divided into various zones according to characteristics of the terrain, and the practical and feasible improvement measures are put forward based on the current situation and main existing problems in the medium- and low-yielding farmland in different areas,

The Type of Low-yielding Fields,Using Direction and Land Fertility Building Measures in Suiping County

Using the evaluation indicator system for arable land fertility in Suiping County,this paper analyzes some factors influencing agricultural production,such as physical and chemical properties of soil,site conditions,soil management,and soil nutrients concerning various types of low-yielding fields in the county. In accordance with the dominant soil constraint factors and main direction of improvement,the lowyielding fields in the county are divided into four types: irrigation improvement type,waterlogging drainage type,barren soil fertilization and barrier layer type. Finally this paper offers specific guidance on the construction of arable land.

配电网低频非线性振荡引发PT保险熔断的机理及抑制措施

电缆的接入使配电网中性点不接地系统对地电容电流增大,产生由单相接地故障引发的低频非线性振荡,导致电磁式电压互感器(potential transformer,PT)保险熔断,严重影响系统安全运行。首先,分析了低频非线性振荡导致PT保险熔断的原理,并基于ATP⁃EMTP平台对10 kV中性点不接地系统进行了仿真计算,计算表明,低频非线性振荡最大过电压小于2.0 p.u.,故障0.1 s后电流接近熔断器熔断电流,系统对地电容增大、零序电阻减小,保险熔断风险增大;然后,仿真验证了4PT接线和PT高压侧中性点串接压敏电阻抑制措施的有效性,并计算了零序电压测量误差;最后,建立10 kV系统的低频非线性振荡试验平台,验证仿真的有效性,对提高配电网PT运行安全性具有参考价值。

基于分数低阶协方差的阵列式超声波测风方法

考虑到当前基于时差法的超声波测风方法是间歇式测量,并且在脉冲噪声背景下测风精度较差,提出一种基于分数低阶协方差的阵列式超声波连续测风方法。该方法采用由一个发射超声波换能器和4个接收换能器组成的超声波测风阵列结构,依托该阵列结构通过对其连续采样并进行分数低阶协方差运算处理以抑制脉冲冲击噪声的影响,然后结合多重信号分类算法即可实现风速风向的高精度连续测量。通过仿真对比实验和实际测量实验验证了所提方法的有效性及优越性,与其他超声波测风方法相比具有更强的噪声抑制能力及测风精度,在实测实验中风速和风向的测量误差分别为1.2%和2°,基本达到了超声波风速风向测量的精度要求。

低温共烧陶瓷激光测厚系统设计与误差分析

基于提升低温共烧陶瓷(low temperature co-fired ceramic,LTCC)厚度的检测精度、测量效率和可溯源性的需求,设计一套LTCC激光测厚系统。针对测量精度难以满足需求的问题,对存在误差进行分析,采用厚度测量用调整夹具消除同轴度误差和线性度误差,优化设计结构降低倾角误差,循环传感器标定消除重复度误差,通过数据优化和滤波处理降低机械振动误差,提高了系统测量精度。与实际产品厚度数据对比,最终精度误差≤5μm,符合产品的应用要求,具有广阔的应用市场。

微弱光探测器光谱响应测量装置

为满足光子计数类型光电探测器光谱响应度的计量需求,建立了微弱光探测器光谱响应测量装置,其特点是可在pW级单色光功率水平下实现光谱比较测量。设计了可调式亮度源,与色散相减双光栅单色仪密闭耦合后实现了6个量级的功率可调单色光输出,可适用于不同光子探测器的线性工作区间,波长范围覆盖330~1 100 nm。设计的密闭准直光路使系统可在正常照明环境下工作,降低了实验环境要求。以集成fA级电流放大器的标准探测器为参考,实现被测光子探测器计数率在1×10^(6)个/s量级的光谱响应度测量。基于LabView编写了专用的控制及数据采集软件,实现了自动化测量。对系统的各项计量特性进行了实验,在330~1 100 nm波段内完成了光子探测器相对光谱响应度测量,相对扩展不确定度为(2.5~3.8)%,k=2。