Effect of Tension on Friction Coefficient Between Lining and Wire Rope with Low Speed Sliding

In order to obtain the exact friction coefficient between lining and wire rope,the tension of wire rope is stud-ied as a factor which affects this coefficient. A mechanical model of a wire rope subjected to axial load was established to determine the torque of the wire rope. The contact motion between lining and wire rope was regarded as a screw rota-tion and the axial force of the lining resulting from the torque of the wire rope was analyzed. Theoretical formulas re-lating tension of the wire rope and the friction coefficient was obtained. Experiments between lining and wire rope with low sliding speed were carried out with friction tester made by us. Experimental results show that increment of the fric-tion coefficient is proportional to that of the tension of the wire rope with a low sliding speed. The experimental results agree with the theoretical calculation; the errors are less than 6%,which proves the validity of the theoretical model.

LUBRICATION FILM FORMATION MECHANISM OF SLIPPER PAIRS IN LOW SPEED HIGH TORQUE HYDRAULIC MOTORS

Pressure-flow analytical formulas of lubrication film of slipper pairs on camshaft connect- ing rod type low speed high torque (LSHT) hydraulic motors are put forward. The bottom surface of slipper pairs is rectangle, and the effect of squeeze flow and pressure differential flow is considered. The dynamic process of lubrication film formation through squeezing is numerically studied by com- puter simulation. Effects of supply pressure, initial lubrication film thickness, velocity damping coef- ficient, loading impact and gravity, etc are studied. Advantages of novel slipper pairs with large oil cavity area are pointed out.

Experiment about Drag Reduction of Bionic Non-smooth Surface in Low Speed Wind Tunnel

The body surface of some organisms has non-smooth structure, which is related to drag reduction in moving fluid. To imitate these structures, models with a non-smooth surface were made. In order to find a relationship be tween drag reduction and the non-smooth surface, an orthogonal design test was employed in a low speed wind tunnel. Six factors likely to influence drag reduction were considered, and each factor tested at three levels. The six factors were the configuration, diameter/bottom width, height/depth, distribution, the arrangement of the rough structures on the experimental model and the wind speed. It was shown that the non-smooth surface causes drag reduction and the distribution of non-smooth structures on the model, and wind speed, are the predominant factors affecting drag reduction. Using analysis of variance, the optimal combination and levels were obtained, which were a wind speed of 44 m/s, distribution of the non-smooth structure on the tail of the experimental model, the configuration of riblets, diameter/bottom width of 1 mm, height/depth of 0.5 mm, arranged in a rhombic formation. At the optimal combination mentioned above, the 99% confidence interval for drag reduction was 11.13 % to 22.30%.

Influence of Low Speed Rolling Movement on High Electrical Breakdown for Water Dielectric with Microsecond Charging

By means of a coaxial apparatus, high electrical breakdown experiments are carried out in the rest state and the low speed rolling state with microsecond charging and the experimental results are analyzed. The conclusions are: (1) the breakdown stress of water dielectric in the rolling state is in good agreement with that in Martin formula, and so is that in the rest state; (2) the breakdown stress of water dielectric in the rolling state is about 5% higher than that in the rest state; (3) the results simulated with ANSYS demonstrate that the breakdown stress of water dielectric decreases when the bubbles appear near the surface of electrodes; (4) the primary mechanism to increase the breakdown stress of water dielectric in the rolling state is that the bubbles are driven away and the number of bubbles near the surface of electrodes is decreased by rolling movement.

Performance analysis of 20 Pole 1.5 KW Three Phase Permanent Magnet Synchronous Generator for low Speed Vertical Axis Wind Turbine

This paper gives performance analysis of a three phase Permanent Magnet Synchronous Generator (PMSG) connected to a Vertical Axis Wind Turbine (VAWT). Low speed wind condition (less than 5 m/s) is taken in consideration and the entire simulation is carried in Matlab/Simulink environment. The rated power for the generator is fixed at 1.5 KW and number of pole at 20. It is observed under low wind speed of6 m/s, a turbine having approximately1 mof radius and2.6 mof height develops 150 Nm mechanical torque that can generate power up to 1.5 KW. The generator is designed using modeling tool and is fabricated. The fabricated generator is tested in the laboratory with the simulation result for the error analysis. The range of error is about 5%-27% for the same output power value. The limitations and possible causes for error are presented and discussed.

A Study on the Maneuvering Motion of a Low Speed Submersible

In this paper,the maneuvering characteristics of a low speed submersible are investigated.First,the captive model tests are carried out to obtain the hydrodynamic forces acting on the submersibleusing a Planar Motion Mechanism(PMM).For the hydrodynamic forces within a wide range of attack an-gles,the hydrodynamic coefficients which are usually used in the conventional maneuvering motion arequite difficult to be applied.In this case,a Fourier series is adopted to represent the hydrodynamic forcesand it fits the experimental data well.Then,based on the experimental results the simulation calculationsare made to predict some of the maneuvering performance of the low speed submersible.

Research on Feature Extraction Method for Low-Speed Reciprocating Bearings Based on Segmented Short Signal Modulation Signal Bispectrum Slicing

Bearing condition monitoring and fault diagnosis (CMFD) can investigate bearing faults in the early stages, preventing the subsequent impacts of machine bearing failures effectively. CMFD for low-speed, non-continuous operation bearings, such as yaw bearings and pitch bearings in wind turbines, and rotating support bearings in space launch towers, presents more challenges compared to continuous rolling bearings. Firstly, these bearings have very slow speeds, resulting in weak collected fault signals that are heavily masked by severe noise interference. Secondly, their limited rotational angles during operation lead to a restricted number of fault signals. Lastly, the interference from deceleration and direction-changing impact signals significantly affects fault impact signals. To address these challenges, this paper proposes a method for extracting fault features in low-speed reciprocating bearings based on short signal segmentation and modulation signal bispectrum (MSB) slicing. This method initially separates short signals corresponding to individual cycles from the vibration signals based on encoder signals. Subsequently, MSB analysis is performed on each short signal to generate MSB carrier-slice spectra. The optimal carrier frequency and its corresponding modulation signal slice spectrum are determined based on the carrier-slice spectra. Finally, the MSB modulation signal slice spectra of the short signal set are averaged to obtain the overall average feature of the sliced spectra.

A new accelerating technique for low speed flow:Pseudo high speed method

This paper proposes a new accelerating technique for simulating low speed flows,termed as p Seudo High Speed method(SHS),which uses governing equations and numerical methods of compressible flows.SHS method has advantages of simple formula,easy manipulation,and only need to modify flux of Euler equations.It can directly employ the existing well-developed schemes of hyperbolic conservation laws.To verify the technique,several numerical experiments are performed,such as:flow past airfoils and flow past a cylinder.Analysis of SHS method and comparisons with some precondition methods are made numerically.All tests show that SHS method can greatly improve the efficiency of compressible method simulating low speed flow fields,which exhibits in accelerating the convergence rate and increasing the accuracy of the numerical results.

Prediction of added resistance of a ship in waves at low speed

This paper presents predictions of the added resistance of a ship in waves at a low speed according to the IMO minimum propulsion power requirement by a hybrid Taylor expansion boundary element method(TEBEM).The flow domain is divided into two parts:the inner domain and the outer domain.The first-order TEBEM with a simple Green function is used for the solution in the inner domain and the zero order TEBEM with a transient free surface Green function is used for the solution in the outer domain.The TEBEM is applied in the numerical prediction of the motions and the added resistance in waves for three new designed commercial ships.The numerical results are compared with those obtained from the seakeeping model tests.It is shown that the prediction of the ship motions and the added resistance in waves are in good agreement with the experimental results.The comparison also indicates that the accuracy of the motion estimation is crucial for the prediction of the wave added resistance.In general,the TEBEM enjoys a satisfactory accuracy and efficiency to predict the added resistance in waves at a low speed according to the IMO minimum propulsion power requirement.

POD analysis of the instability mode of a low-speed streak in a laminar boundary layer

The instability of one single low-speed streak in a zero-pressure-gradient laminar boundary layer is investigated experimentally via both hydrogen bubble visualization and planar particle image velocimetry(PIV) measurement. A single low-speed streak is generated and destabilized by the wake of an interference wire positioned normal to the wall and in the upstream. The downstream development of the streak includes secondary instability and self-reproduction process, which leads to the generation of two additional streaks appearing on either side of the primary one. A proper orthogonal decomposition(POD) analysis of PIV measured velocity field is used to identify the components of the streak instability in the POD mode space: for a sinuous/varicose type of POD mode, its basis functions present anti-symmetric/symmetric distributions about the streak centerline in the streamwise component, and the symmetry condition reverses in the spanwise component. It is further shown that sinuous mode dominates the turbulent kinematic energy(TKE) through the whole streak evolution process, the TKE content first increases along the streamwise direction to a saturation value and then decays slowly. In contrast, varicose mode exhibits a sustained growth of the TKE content,suggesting an increasing competition of varicose instability against sinuous instability.

SOME CHARACTERISTICS OF LOW-SPEED STREAKS UNDER SHEARED AIR-WATER INTERFACES

The characteristics of low-speed fluid streaks occurring under shearedair-water interfaces were examined by means of hydrogen bubble visualization tech-nique.A critical shear condition under which the streaky structure first appears wasdetermined to be u_r≈0.19 cm/s.The mean spanwise streak spacing increases withdistance from the water surface owing to merging and bursting processes,and a lin-ear relationship describing variation of non-dimensional spacing (?) versus y^+ wasfound essentially independent of shear stress on the interface.Values of (?),however,are remarkably smaller than their counterparts in the near-wall region of turbulentboundary layers.Though low-speed streaks occur randomly in time and space,thestreak spacing exhibits a lognormal probability distribution behavior.A tentativeexplanation concerning the formation of streaky structure is suggested,and the factthat (?) takes rather smaller values than that in wall turbulence is briefly discussed.

Numerical study on evolution of subharmonic varicose low-speed streaks in turbulent channel flow

The evolution of two spanwise-aligned low-speed streaks in a wall turbulent flow, triggered by the instability of the subharmonic varicose(SV) mode, is studied by a direct numerical simulation(DNS) method in a small spatial-periodic channel. The results show that the SV low-speed streaks are self-sustained at the early stage, and then transform into subharmonic sinuous(SS) low-speed streaks. Initially, the streamwise vortex sheets are formed by shearing, and then evolve into zigzag vortex sheets due to the mutual induction. As the intensification of the SV low-speed streaks becomes prominent,the tilted streamwise vortex tubes and the V-like streamwise vortex tubes can be formed simultaneously by increasing +? u? x. When the SV low-speed streaks break down, new zigzag streamwise vortices will be generated, thus giving birth to the next sustaining cycle of the SV low-speed streaks. When the second breakdown happens, new secondary V-like streamwise vortices instead of zigzag streamwise vortices will be generated. Because of the sweep motion of the fluid induced by the secondary V-like streamwise vortices, each decayed low-speed streak can be divided into two parts, and each part combines with the part of another streak, finally leading to the formation of SS low-speed streaks.

Dynamics of low-speed streak evolution and interaction in laminar boundary layer

The present paper presents an experimental effort on the regeneration process of two low-speed laminar streaks in a zero-pressure-gradient laminar boundary layer.Two vertical thin wires separated by a spanwise distance of 30 mm are used to introduce disturbances of two rolls of transitional Ka′rma′n vortex street to the downstream boundary layer. Both hydrogen bubble visualization and particle image velocimetry(PIV) measurement show that two lowspeed streaks are induced through leading-edge receptivity process. As these streaks develop in the downstream, two additional low-speed streaks begin to appear outboard of the flank of the original two, together with complex dynamics of streak splitting and merging. A flow pattern of four streaks aligned along the spanwise direction occurs finally in the far downstream. It is found that besides the mechanisms of streak breakdown, the streak interaction is also an important factor characterizing the instability of low speed streaks and their regeneration process.

A study of parameter-free shock capturing upwind schemes on low speeds' issues

Nowadays,the upwind schemes are in a rapid development to capture shock accurately.However,these upwind schemes’properties at low speeds,such as their reconstruction scheme dependencies,grid dependencies,and Mach number dependencies,are concerned by few people.In this paper,a systematic study on their low speeds’issues is conducted.Through a series of tests,we can find that most parameter-free upwind schemes,widely used in practice today,are not applicable to low speeds’simulations.In contrast,SLAU and SLAU2 can give reliable results.Also,the upwind scheme’s influence on the accuracy is stronger than the reconstruction scheme’s influence at low speeds.

Statistical analysis of pressure fluctuations during unsteady flow for low-specific-speed centrifugal pumps

A three-dimensional transient numerical simulation was conducted to study the pressure fluctuations in low-specific-speed centrifugal pumps. The characteristics of the inner flow were investigated using the SST k–ω turbulence model. The distributions of pressure fluctuations in the impeller and the volute were recorded, and the pressure fluctuation intensity was analyzed comprehensively, at the design condition, using statistical methods. The results show that the pressure fluctuation intensity increases along the impeller streamline from the leading edge to the trailing edge. In the impeller passage, the intensity near the shroud is much higher than that near the hub at the inlet. However, the intensity at the middle passage is almost equal to the intensity at the outlet. The pressure fluctuation intensity is the highest at the trailing edge on the pressure side and near the tongue because of the rotor–stator interaction. The distribution of pressure fluctuation intensity is symmetrical in the axial cross sections of the volute channel. However, this intensity decreases with increasing radial distance. Hence, the pressure fluctuation intensity can be reduced by modifying the geometry of the leading edge in the impeller and the tongue in the volute.

Numerical simulation on evolution of subharmonic low-speed streaks in minimal channel turbulent flow

The evolution of low-speed streaks in the turbulent boundary layer of the minimum channel flow unit at a low Reynolds number is simulated by the direct numerical simulation(DNS) based on the standard Fourier-Chebyshev spectral method.The subharmonic sinuous(SS) mode for two spanwise-aligned low-speed streaks is excited by imposing the initial perturbations.The possibilities and the physical realities of the turbulent sustaining in the minimal channel unit are examined.Based on such a flow field environment,the evolution of the low-speed streaks during a cycle of turbulent sustaining,including lift-up,oscillation,and breakdown,is investigated.The development of streamwise vortices and the dynamics of vortex structures are examined.The results show that the vortices generated from the same streak are staggered along the streamwise direction,while the vortices induced by different streaks tilt toward the normal direction due to the mutual induction effect.It is the spatial variations of the streamwise vortices that cause the lift-up of the streaks.By resolving the transport dynamics of enstrophy,the strength of the vortices is found to continuously grow in the logarithmic layer through the vortex stretching mechanism during the evolution of streaks.The enhancement of the vortices contributes to the spanwise oscillation and the following breakdown of the low-speed streaks.

Optimization on the Impeller of a Low-specific-speed Centrifugal Pump for Hydraulic Performance Improvement

In order to widen the high-efficiency operating range of a low-specific-speed centrifugal pump, an optimization process for considering efficiencies under 1.0Q_d and 1.4Q_d is proposed. Three parameters, namely, the blade outlet width b_2, blade outlet angle β_2, and blade wrap angle φ, are selected as design variables. Impellers are generated using the optimal Latin hypercube sampling method. The pump efficiencies are calculated using the software CFX 14.5 at two operating points selected as objectives. Surrogate models are also constructed to analyze the relationship between the objectives and the design variables. Finally, the particle swarm optimization algorithm is applied to calculate the surrogate model to determine the best combination of the impeller parameters. The results show that the performance curve predicted by numerical simulation has a good agreement with the experimental results. Compared with the efficiencies of the original impeller, the hydraulic efficiencies of the optimized impeller are increased by 4.18% and 0.62% under 1.0Q_d and 1.4Q_d, respectively. The comparison of inner flow between the original pump and optimized one illustrates the improvement of performance. The optimization process can provide a useful reference on performance improvement of other pumps, even on reduction of pressure fluctuations.

Mathematical Modeling,Field Calibration and Numerical Simulation of Low-Speed Mixed Traffic Flow in Cities

Ｗｉｔｈｔｈｅｒａｐｉｄｄｅｖｅｌｏｐｍｅｎｔｏｆｔｒａｎｓｐｏｒｔａｔｉｏｎａｎｄａｕｔｏｍｏｂｉｌｅｉｎｄｕｓｔｒｙ，ｔｈｅｃｏｎｆｌｉｃｔｂｅｔｗｅｅｎｍｏｔｏｒｍａｎｕｆａｃｔｕｒｅａｎｄｈｉｇｈｗａｙｃｏｎｓｔｒｕｃｔｉｏｎｂｅｃｏｍｅｓｓ...

Deformation simulation of low-temperature high-speed extrusion for 6063 Al alloy

The hot compression test of 6063 Al alloy was performed on a Gleeble-1500 thermo-simulation machine,and the forming of 6063 rod extrudate in low-temperature high-speed extrusion was simulated with extrusion ratio of 25 on the platform of DEFORM 2D successfully.From the compression experimental results,the flow stress model of this Al alloy is obtained which could be the constitutive equation in the simulation of low-temperature high-speed extrusion process.From the numerical simulation results,there is a higher strain concentration at the entrance of the die and the exit temperature reaches up to 522℃in low-temperature high-speed extrusion,which approaches to the quenching temperature of the 6063 Al alloy.The results show that the low-temperature high-speed extrusion method as a promsing one can reduce energy consumption effectively.

High speed railway promoting development of low-carbon economy in China

Low-carbon Economy is a kind of economic developing mode which takes low energy consumption,low pollution and low discharge as its foundation. It is another important revolution of the human society after the agriculture civilization and industry civilization. It deals with various fields including low-carbon energy,low-carbon agriculture,low-carbon industry,low-carbon transportation and low-carbon life,etc. Among those,low-carbon transportation is one of the important contents. Since high speed railway uses electricity as driving force,it runs without discharging waste gas,and it is a kind of clean and green transportation with little dust and smoke black. Therefore,the study of the relationship between the high speed railway and low-carbon economy is becoming one of the important frontier problems that confronting the theoretic circle. With demonstration analysis and comparative analysis,this paper discusses the comparative advantages of high speed railway in terms of energy saving and environment protection,treatment of sound pollution,land saving and reduction of external cost(mainly pollution treatment cost) ,etc. compared with the other transportation modes and ordinary railway. Taking Beijing-Tianjin Intercity Railway as an example,the paper further demonstrates the distinctive advantages in respect of energy conservation and emission reduction. Besides,the paper also predicates the low-carbon effects after several high speed railways is put into operation in a few years. It is concluded that the development of high speed railways will meet the need of low-carbon economy and is significant for sustainable and steady development of economy and society.