The feasibility of applying the grain boundary character distribution(GBCD)optimization to Inconel 625 for improving the intergranular corrosion(IGC)resistance was studied.The GBCD was obtained and characterized by el...The feasibility of applying the grain boundary character distribution(GBCD)optimization to Inconel 625 for improving the intergranular corrosion(IGC)resistance was studied.The GBCD was obtained and characterized by electron backscatter diffraction(EBSD)analysis,and its optimization was mainly attributed to annealing twins(Σ3)and twins related to boundaries formed during thermal-mechanical processing(TMP).Through TMP of 5%cold rolling and subsequent annealing at 1150℃for 5 min,the proportion of lowΣcoincidence site lattice(CSL)grain boundaries of the Inconel 625 can be enhanced to about 35.8%which mainly were ofΣ3^(n)(n=1,2,3)type.There is an increase of 24.8%compared with the solution-treated sample,and simultaneously the large-size highly-twinned grain-cluster microstructure is formed.The grain-cluster is mainly composed ofΣ3-Σ3-Σ9 orΣ3-Σ9-Σ27 triple junctions,which is mainly caused by boundary reactions during grain growth.Among them,the IGC resistance ofΣ3 grain boundaries,Σ9 grain boundaries and random grain boundaries is sequentially weakened.With the increase of the lowΣCSL grain boundary fraction,the IGC resistance of Inconel 625 improves.The essential reason is the amount ofΣ3 boundaries interrupting the random boundary network increases and the large grain-cluster arrests the penetration of IGC.展开更多
运用电子背散射衍射(EBSD)和取向成像显微技术(OIM)研究了退火时间和冷轧变形量对Incoloy 800合金晶界特征分布的影响。结果显示,随着退火时间的延长,总的低ΣCSL(coincidence site lattice,Σ≤29)晶界比例在60%～70%范围内缓慢增长,Σ...运用电子背散射衍射(EBSD)和取向成像显微技术(OIM)研究了退火时间和冷轧变形量对Incoloy 800合金晶界特征分布的影响。结果显示,随着退火时间的延长,总的低ΣCSL(coincidence site lattice,Σ≤29)晶界比例在60%～70%范围内缓慢增长,Σ1晶界比例随Σ3晶界比例上升而下降。随着变形量的增加,总的低ΣCSL晶界、Σ3晶界、Σ9晶界和Σ27晶界比例均呈现先增加后降低的趋势,而Σ1晶界相反,出现先降低后增加的趋势。优化的Incoloy 800合金晶界工程工艺为:在980℃固溶处理15 min,冷轧5%后在980℃退火15 min。展开更多
We link different microstructures to tribological behaviors of Ti-50.8 Ni(mole fraction, %) in reciprocating mode at room temperature(20 ℃). Hot-rolled alloys with B2 phase exhibit lower coefficient of friction and w...We link different microstructures to tribological behaviors of Ti-50.8 Ni(mole fraction, %) in reciprocating mode at room temperature(20 ℃). Hot-rolled alloys with B2 phase exhibit lower coefficient of friction and wear rate compared to the ones with B19?. Stress-induced martensitic transformation occurs during sliding. However, multi-pass hot rolling weakens the wear resistance. In this study, microstructures were characterized through electron backscatter diffraction and transmission electron microscopy(EBSD/TEM). From the concept of energy conservation, the effects of weak intensity of hot-rolled textures on the wear resistance are minimal. Based on the result that the alloy with a higher portion of coincidence site lattice boundaries shows lower martensitic start transformation temperature in the DSC curves than that with higher KAM values, the delay on B2-B19? transformation from {112}B2 twins outweighs dislocations. Moreover, widely distributed small-angle grain boundaries owing to dynamic recovery improve the wear resistance effectively compared to those that are well-recrystallized.展开更多
In order to understand the basic mechanism of intergranular cracking in pure metals during fatigue, stress-controlled push-pull fatigue tests were carried out with high purity aluminium. Tests were interrupted frequen...In order to understand the basic mechanism of intergranular cracking in pure metals during fatigue, stress-controlled push-pull fatigue tests were carried out with high purity aluminium. Tests were interrupted frequently so as to study the grain boundary (GB) cracking behaviour by the surface observation. The results show that crack initiation at GB was a process controlled by multi-factors, such as boundary structure, GB-slip interaction, GB sliding and so on. If these factors are varied so that the incompati- bility at a GB increased, the possibility of cyacking at the boundary will be raised. Some inteygranular cracking phenomena are not able to be explained by the GB stepping mechanism.展开更多
基金Funded in part by the National Key Research and Development Program of China(No.2017YFA07007003)the National Natural Science Foundation of China(No.51661019)+1 种基金the Major Projects of Science and Technology in Gansu Province(No.145RTSA004)the Hongliu First-class Discipline Construction Plan of Lanzhou University of Technology。
文摘The feasibility of applying the grain boundary character distribution(GBCD)optimization to Inconel 625 for improving the intergranular corrosion(IGC)resistance was studied.The GBCD was obtained and characterized by electron backscatter diffraction(EBSD)analysis,and its optimization was mainly attributed to annealing twins(Σ3)and twins related to boundaries formed during thermal-mechanical processing(TMP).Through TMP of 5%cold rolling and subsequent annealing at 1150℃for 5 min,the proportion of lowΣcoincidence site lattice(CSL)grain boundaries of the Inconel 625 can be enhanced to about 35.8%which mainly were ofΣ3^(n)(n=1,2,3)type.There is an increase of 24.8%compared with the solution-treated sample,and simultaneously the large-size highly-twinned grain-cluster microstructure is formed.The grain-cluster is mainly composed ofΣ3-Σ3-Σ9 orΣ3-Σ9-Σ27 triple junctions,which is mainly caused by boundary reactions during grain growth.Among them,the IGC resistance ofΣ3 grain boundaries,Σ9 grain boundaries and random grain boundaries is sequentially weakened.With the increase of the lowΣCSL grain boundary fraction,the IGC resistance of Inconel 625 improves.The essential reason is the amount ofΣ3 boundaries interrupting the random boundary network increases and the large grain-cluster arrests the penetration of IGC.
基金financially supported by the National Natural Science Foundation of China-Aerospace Science and Technology Corporation of China Aerospace Advanced Manufacturing Technology Research Joint Fund (U1737204)the National Natural Science Foundation of China (51673205)the Key Research Program of Frontier Science,Chinese Academy of Sciences (QYZDJ-SSW-SLH056)。
文摘We link different microstructures to tribological behaviors of Ti-50.8 Ni(mole fraction, %) in reciprocating mode at room temperature(20 ℃). Hot-rolled alloys with B2 phase exhibit lower coefficient of friction and wear rate compared to the ones with B19?. Stress-induced martensitic transformation occurs during sliding. However, multi-pass hot rolling weakens the wear resistance. In this study, microstructures were characterized through electron backscatter diffraction and transmission electron microscopy(EBSD/TEM). From the concept of energy conservation, the effects of weak intensity of hot-rolled textures on the wear resistance are minimal. Based on the result that the alloy with a higher portion of coincidence site lattice boundaries shows lower martensitic start transformation temperature in the DSC curves than that with higher KAM values, the delay on B2-B19? transformation from {112}B2 twins outweighs dislocations. Moreover, widely distributed small-angle grain boundaries owing to dynamic recovery improve the wear resistance effectively compared to those that are well-recrystallized.
文摘In order to understand the basic mechanism of intergranular cracking in pure metals during fatigue, stress-controlled push-pull fatigue tests were carried out with high purity aluminium. Tests were interrupted frequently so as to study the grain boundary (GB) cracking behaviour by the surface observation. The results show that crack initiation at GB was a process controlled by multi-factors, such as boundary structure, GB-slip interaction, GB sliding and so on. If these factors are varied so that the incompati- bility at a GB increased, the possibility of cyacking at the boundary will be raised. Some inteygranular cracking phenomena are not able to be explained by the GB stepping mechanism.
