Effect of lower bainite/martensite/retained austenite triplex microstructure on the mechanical properties of a low-carbon steel with quenching and partitioning process

We present a study concerning Fe-0. 176C-1.31Si-1.58Mn-0.26Al-0.3Cr （wt%） steel subjected to a quenching and partitioning （Q＆P） process. The results of scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and tensile tests demon- strate that the microstructures primarily consist of lath martensite, retained austenite, lower bainite （LB）, and a small amount of tempered martensite; moreover, few twin austenite grains were observed. In the microstrucmre, three types of retained austenite with different sizes and morphologies were observed： blocky retained austenite （-300 nm in width）, film-like retained austenite （80-120 nm in width）, and ul- tra-fine film-like retained austenite （30-40 nm in width）. Because of the effect of the retained austenite/martensite/LB triplex microstructure, the specimens prepared using different quenching temperatures exhibit high ultimate tensile strength and yield strength. Furthermore, the strength effect of LB can partially counteract the decreasing strength effect of martensite. The formation of LB substantially reduces the amount of retained austenite. Analyses of the retained austenite and the amount of blocky retained austenite indicated that the carbon content is critical to the total elongation of Q＆P steel.

Metal magnetic memory signals from surface of low-carbon steel and low-carbon alloyed steel

In order to investigate the regularity of metal magnetic signals of ferromagnetic materials under the effect of applied load, the static tensile test of Q235 steel and 18CrNiWA steel plate specimens were conducted and metal magnetic memory signals of specimens were measured during the test process. The influencing factors of metal magnetic memory signals and the relationship between axial applied load and signals were analyzed. The fracture and microstructure of the specimens were observed. The results show that the magnetic signals corresponding to the measured points change linearly approximately with increasing axial load. The microstructure of Q235 steel is ferrite and perlite, whereas that of 18CrNiWA steel is bainite and low-carbon martensite. The fracture of these two kinds of specimens is ductile rupture; carbon content of specimen materials and dislocation glide give much contribution to the characteristics of magnetic curves.

Effect of plastic strain and forming temperature on magnetic properties of low-carbon steel

Claw poles are a key component of automobile generators.The output power performance of the generator is very dependent on the magnetic properties of its claw poles.Plastic deformation is known to significantly change the magnetic behavior of ferromagnetic materials in claw poles.In this paper,changes in the magnetic properties of low-carbon steel,used for claw pole components due to their plastic deformation,were investigated for different strains and temperatures.Ring-shaped material samples were prepared by machining and their magnetic properties were measured.The surface roughness was first evaluated and a machining process with an arithmetic average of roughness Ra 1.6μm was selected as enabling the lowest measurement error.Hysteresis loops at different applied magnetic fields of the material were obtained for different plastic strains and forming temperatures.The magnetic parameters of magnetic flux density,coercivity,and remanence were obtained and compared with magnetic flux density as the primary focus.Results showed that machining,cold forming,and hot forming all led to lower magnetic flux density,larger coercivity,and smaller remanence.Magnetic flux density showed a sharp decrease at the start of plastic deformation,but as the strain increased,the decreasing trend gradually reached a constant value.The decrease was much larger for cold forming than for hot forming.For example,at 500 A/m,the degradation of magnetic flux density with a reduction percentage of 5%at room temperature was about 50%,while that of hot forming at 1200°C was about 10%.Results of this research may provide a reference for the future process design of hot-forged claw poles.

Analysis of Coating Microstructure of Hot-Dip Aluminum of Deformed Low-Carbon Steel Containing Rare Earth

The coating microstructure of hot-dip aluminum (HDA) of deformed low-carbon steel containing RE was analyzed by metallography microscopy, TEM and XRD, and the forming mechanism was also discussed. The results show that, the Fe_2Al_5 phase, on whose subcrystal boundaries, Al particles with the size of 7～30 μm existing on parallel linear are, grows a strong orientation. And the spread activation energy of Al is 155.22 kJ·mol -1. In addition, the effects of deformation on coating microstructure of hot-dip aluminum and the function of RE were preliminarily analyzed.

Microstructural evolution during ultra-rapid annealing of severely deformed low-carbon steel: strain, temperature, and heating rate effects

An interaction between ferrite recrystallization and austenite transformation in low-carbon steel occurs when recrystallization is delayed until the intercritical temperature range by employing high heating rate. The kinetics of recrystallization and transformation is affected by high heating rate and such an interaction. In this study, different levels of strain are applied to low-carbon steel using a severe plastic deformation method. Then, ultra-rapid annealing is performed at different heating rates of 200–1100°C/s and peak temperatures of near critical temperature. Five regimes are proposed to investigate the effects of heating rate, strain, and temperature on the interaction between recrystallization and transformation. The microstructural evolution of severely deformed low-carbon steel after ultra-rapid annealing is investigated based on the proposed regimes. Regarding the intensity and start temperature of the interaction, different microstructures consisting of ferrite and pearlite/martensite are formed. It is found that when the interaction is strong, the microstructure is refined because of the high kinetics of transformation and recrystallization. Moreover, strain shifts an interaction zone to a relatively higher heating rate. Therefore, severely deformed steel should be heated at relatively higher heating rates for it to undergo a strong interaction.

Study on Carburizing Kinetics of Low-carbon Steel at High-temperature and Short-term

In this paper, the carburizing kinetics of low-carbon steel at high-temperature and short-term in liquid cast-iron were studied by metallographic microscope, chemical analysis and so on, and the microstructure of carburized layer was also analyzed. The results show that the carburizing rate of low-carbon steel at high-temperature and short-term is so fast, and the microstructure of carburized layer possess higher carbon content, and cementite, pearlite and ferrite exist in carburized layer structure simultaneously. Besides, the kinetic equations of permeating layer forming have been presented, and the carburizing mechanism was preliminary discussed also.

Layer Structure Analysis of Low-Carbon Steel Containing Rare Earth by High-Temperature Carburizing of Liquid Cast-Iron

The layer structure of low-carbon steel containing RE by high-temperature (T>1200 ℃) carburizing of liquid cast-iron was studied and the diffusion activation energy of carbon was calculated by metallographic microscpe, chemical analysis etc. The result shows that the technology of carburizing in liquid cast-iron can expedite caburization distinctly and changes the carburizing layer structure. The carburizing rate is 60～80 times of that of the traditional technology, and there is about 43% decrease in the activation energy compared with gas-carburization. In outer structure layer, cementite is formed simultaneously both on the crystal boundary reticularly and inside the crystal grains stripedly. In inner carburizing layer, there is undissolved blocky ferrite in reticular cementite. Besides, rare earth element can expedite carburization process.

Research on Welding Test of Grey Cast Iron and Low-Carbon Steel

Grey cast iron’s welding itself is a complex proble m.So proper welding materials must be selected,complex welding techniques such as preheating before weldingslow cooling after welding etc,should be taken. However the carbon component in low-carbon steel is comparatively low,the carbo n of welded joint will diffuse to the low-carbon steel when it is welded with gr ey cast iron,which will cause the component of carbon greatly increased at the low-carbon steel side in HAZ,high carbon martensite and cracks will occur.If p reheating before weldingslow cooling after welding and other welding procedure are taken,the grey cast iron side can probably be qualified.But the carbon wi ll diffuse to HAZ of the low-carbon steel side more easily.Therefore after stud ying the weldabilities of grey cast iron and low-carbon steel,the author develo ped a new type of cast iron electrode considering the demands of factories’prac tices,and the welding technology test of grey cast iron and low-carbon steel ar e carried out. In this paper,a new type of grey cast iron electrode is developed based on the practices in factories,its ingredients and properties are introduced.The w elding tests of grey cast iron and low-carbon steel are practiced.The joint str ucture of the dissimilar metal and the appearance of weld are observed.The hard ness distribution of the welded joint is tested.The results show that the elect rode can meet the welding requirements of the grey cast iron and low-carbon stee l.There are no cracksgas pores and other defects of metallurgy in welded join t,the appearance of welded joint are good.

Hydrogen Permeation and Diffusion in Low-carbon Steels and 16Mn Steel

In the present work. the hydrogen permeation and diffusion in two low-carbon steels. # 10 and #20. and 16Mn stee1 over the temperature range of 80 to 330℃ were investigated using gaseous permeation technique. The temperature dependence of hydrogen permeability. diffusivity and solubility for the three steels was obtained in the form of the Arrhenius equations. It was shown that the hydrogen permeability of the 16Mn steel is somewhat lower than that of the two low-carbon steels.whereas the hydrogen diffusivity is lowered in the order of #10, #20 and 16Mn but the activation energy of diffusion is much the same for the three steels. The difference in the diffusivity was attributed to the increase of ferrite-cementite interface areas with the refinement of pearlitic structure in the steels

Cleanliness of Ti-bearing Al-killed ultra-low-carbon steel during different heating processes

During the production of Ti-bearing Al-killed ultra-low-carbon(ULC) steel, two different heating processes were used when the converter tapping temperature or the molten steel temperature in the Ruhrstahl–Heraeus(RH) process was low: heating by Al addition during the RH decarburization process and final deoxidation at the end of the RH decarburization process(process-Ⅰ), and increasing the oxygen content at the end of RH decarburization, heating and final deoxidation by one-time Al addition(process-Ⅱ). Temperature increases of 10°C by different processes were studied; the results showed that the two heating processes could achieve the same heating effect. The T.[O] content in the slab and the refining process was better controlled by process-Ⅰ than by process-Ⅱ. Statistical analysis of inclusions showed that the numbers of inclusions in the slab obtained by process-Ⅰ were substantially less than those in the slab obtained by process-Ⅱ. For process-Ⅰ, the Al_2O_3 inclusions produced by Al added to induce heating were substantially removed at the end of decarburization. The amounts of inclusions were substantially greater for process-Ⅱ than for process-Ⅰ at different refining stages because of the higher dissolved oxygen concentration in process-Ⅱ. Industrial test results showed that process-Ⅰ was more beneficial for improving the cleanliness of molten steel.

Analysis of the formation conditions and characteristics of interphase and random vanadium precipitation in a low-carbon steel during isothermal heat treatment

The characteristics of nanosized precipitates in steels depend on the heat-treatment parameters. The effects of characteristics of vanadium precipitates formed during isothermal heat treatment on the hardness of the ferrite matrix in low-carbon vanadium-alloyed steel were investigated through analysis of transmission electron microscopy images and microhardness measurements. The results show that, during isothermal holding in the temperature range from 675 to 750℃, only interphase precipitation occurs, whereas only random precipitation occurs in the ferrite matrix during holding at 600℃. Furthermore, during isothermal heat treatment between 600 and 675℃, both random and interphase precipitates occurred in the ferrite. Nanoscale vanadium carbides with different atomic ratios of vanadium(V) and carbon(C) were the dominant precipitates in the random and interphase precipitates. The sizes of random precipitation carbides were smaller than those of interphase ones. Also, the sample isothermally heat treated at 650℃ for 900s exhibited a higher hardness with a narrower hardness distribution.

Influence of high deformation on the microstructure of low-carbon steel

Low-carbon steel sheets DC04 used in the automotive industry were subjected to cold rolling for thickness reduction from 20% to 89%. The desired thickness was achieved by successive reductions using a rolling mill. The influence of thickness reduction on the microstructure was studied by scanning electron microscopy. Microstructure evolution was characterized by the distortion of grains and the occurrence of the oriented grain structure for high cold work. A mechanism of grain restructuring for high cold work was described. The occurrence of voids was discussed in relation with cold work. The evolution of voids at the grain boundaries and inside the grains was also considered. To characterize the grain size, the Feret diameter was measured and the grain size distribution versus cold work was discussed. The chemical homogeneity of the sample was also analyzed.

Studies on Effects of Welding Parameters on the Mechanical Properties of Welded Low-Carbon Steel

In this work, the effect of heat input on the mechanical properties of low-carbon steel was studied using two welding processes: Oxy-Acetylene Welding (OAW) and Shielded Metal Arc Welding (SMAW). Two different edge preparations on a specific size, 10-mm thick low-carbon steel, with the following welding parameters: dual welding voltage of 100 V and 220 V, various welding currents at 100, 120, and 150 Amperes and different mild steel electrode gauges of 10 and 12 were investigated. The tensile strength, hardness and impact strength of the welded joint were carried out and it was discovered that the tensile strength and hardness reduce with the increase in heat input into the weld. However, the impact strength of the weldment increases with the increase in heat input. Besides it was also discovered that V-grooved edge preparation has better mechanical properties as compared with straight edge preparation under the same conditions. Microstructural examinations conducted revealed that the cooling rate in different media has significant effect on the microstructure of the weldment. Pearlite and ferrite were observed in the microstructure, but the proportion of ferrite to pearlite varied under different conditions.

Aging behavior of a copper-bearing high-strength low-carbon steel

The effects of aging temperature and time on the hardness and impact toughness of a copper-bearing high-strength low-carbon steel were investigated. The hardness of the aged samples reached maxima after 1 h and 5 h of aging at 500 and 450℃, respectively; this increase in hardness was followed by a decrease in hardness until a temperature of 700℃, at which secondary hardening was observed. The impact toughness of the aged steel was found to be higher for 5 h of aging. Transmission electron microscopy confirmed the presence of carbide and copper precipitates; also, the secondary hardening could be the result of the transformation of austenite（formed in the aging treatment） to martensite. Differential scanning calorimetry of the steel was performed to better understand the precipitation behavior. The results revealed that the precipitation of the steel exhibited two significant stages of copper precipitate nucleation and coarsening of the precipitates, with corresponding activation energies of 49 and 238 kJ·mol^-1, respectively.

INFLUENCE OF TIN ON THE HOT DUCTILITY OF A LOW-CARBON STEEL

The influence of tin on the hot ductility of a 0.15wt%C steel is investigated using a continuous-casting thermal simulator with three cooling rates. Tin can apparently deteriorate the hot ductility of the steel. Non-equilibrium grain boundary segregation of tin occurs during cooling and plays an important role in reducing the hot ductility of the steel. There is a critical cooling rate for the Sn segregation being between 5 and 20K/s.

Mechanical properties of fine-grained dual phase low-carbon steels based on dynamic transformation

The fine grained dual phase （FG-DP） steel with ferrite grains of 2-4.5 μm and martensite islands smaller than 3 μm was obtained through the mechanism of deformation-enhanced ferrite transformation （DEFT）. Mechanical properties of the steel were tested at room temperature. The results indicated that with a similar volume fraction of martensite （about 20vol%）,FG-DP steel exhibited a superior combination of higher strength and more rapid strain hardening at low strains compared with the coarse-grained dual phase （CG-DP） steel obtained by critical annealing. The combination of higher strength,large elongation,and more rapid strain hardening of FG-DP steel can be attributed to the fine ferrite grain and finely dispersed martensite islands. In addition,the uniformly distributed martensite islands in FG-DP steel have smaller interspacing compared with that of CG-DP steel. So,at the initial plastic deformation stage,the plastic deformation of ferrite was restrained and more pronounced load was transferred from ferrite to martensite. The plastic deformation of martensite in FG-DP steel started earlier.

Mechanical and corrosion properties of low-carbon steel prepared by friction stir processing

Low-carbon steel plates were successfully subjected to normal friction stir processing(NFSP) in air and submerged friction stir processing(SFSP) under water, and the microstructure, mechanical properties, and corrosion behavior of the NFSP and SFSP samples were investigated. Phase transformation and dynamic recrystallization resulted in fine-grained ferrite and martensite in the processed zone. The SFSP samples had smaller ferrites(5.1 μm), finer martensite laths(557 nm), and more uniform distribution of martensite compared to the NFSP samples. Compared to the base material(BM), the microhardness of the NFSP and SFSP samples increased by 19.8% and 27.1%, respectively because of the combined strengthening effects of grain refinement, phase transformation, and dislocation. The ultimate tensile strengths(UTSs) of the NFSP and SFSP samples increased by 27.1% and 38.7%, respectively. Grain refinement and martensite transformation also improved the electrochemical corrosion properties of the low-carbon steel. Overall, the SFSP samples had better mechanical properties and electrochemical corrosion resistance than the NFSP samples.

Analysis of surface microcracks in low-carbon steel produced via twin-roll strip casting

In this study,morphological and microstructural analyses were conducted on net-shaped microcracks appearing on the surface of low-carbon steel manufactured via twin-roll strip casting. The fractograph and microscale distribution of elements in the cracked region were also analyzed. Results revealed that the cracked surfaces were characterized by slight pits,along with inclusions composed of manganese and silicon oxide distributed along both the sides of the cracks. Fractograph analysis revealed that the crack and smooth dendrite surfaces were oxidized. These phenomena indicate that microcracks on the cast strip surface form at the hightemperature stage of the solidification process during twin-roll casting and rolling. Microcracks were present in each region with pits in the cast strip and extended along the dendrite interface because of the combined effects of phasechange stress,thermal stress,mechanical stress,and fractional crystallization during the solidification process.

Recrystallization Kinetics and Microstructure Evolution of Annealed Cold-Drawn Low-Carbon Steel

The recrystallization behavior of cold-drawn 0.12 wt% C steel during annealing at temperatures 600°C and 650°C was investigated. Hardness tests were used to characterize the recrystallization kinetics. The micrographs of the steel were obtained using optical microscopy (OM) to characterize the grain microstructure of the non-treated and the annealed steel samples. Annihilation of dislocation defects occur within the soaking time of 5 - 10 minutes for all the deformed steel after annealing at 650°C. Specifically at 5 minutes soaking time the grains elongation is still observed indicating that reformation of grains is not taking place but recovery of the deformed grains. At the 10 minutes annealing time, new grains are observed to begin and full recrystallization is achieved at 15 minutes annealing time. At annealing time between 20 - 25 minutes, grains coarsening are observed indicating the onset of grain growth. The hardness of the material reduces with increasing annealing temperature for all the degree of cold drawn deformation. On the basis of the experimentally obtained hardness values, recrystallization increases with increasing degree of cold drawn deformation for the annealed steel. Recovery process was found to prolong in the 20% cold drawn steel as compared to the 55% cold drawn steel. The prolong recovery process is due to reduction in the driving force. Full recrystallization of the annealed steel is achieved at different soaking time depending on the degree of the cold drawn steel.

Effect of Heat Treatments on Corrosion of Welded Low-Carbon Steel in Acid and Salt Environments

Effect of heat treatment on the corrosion of welded low-carbon steel in 0.3 M and 0.5 M of hydrochloric acid and sodium chloride environments at ambient temperature (25oC) has been investigated. Arc welded low-carbon steel sample of known composition were subjected to the corrosion reagents for 21 days (504 hours). pH and weight loss values were taken at interval of 3 days. Thereafter, weight loss method was used to measure therate of corrosion attack on the heat treated samples at ambient temperature. Results obtained showed that at low concentration, the annealed sample exhibits better corrosion characteristic as compared to the normalized and quenched samples. However, at higher concentration the normalized sample exercised better service performance over the annealed and quenched samples. Thequenched sample was found to have relatively low corrosion performance over the annealed and normalized samples at both low and high concentrations of the media.