A research concerning the coupling conditions of gas leakage through suction valves and capacity regulation is performed in an industrial reciprocating compressor.Both internal flow and thermodynamic characteristic ar...A research concerning the coupling conditions of gas leakage through suction valves and capacity regulation is performed in an industrial reciprocating compressor.Both internal flow and thermodynamic characteristic are discussed in detail.The results show that the capacity of compressor can be regulated steplessly by controlling suction valve closure moment.And then the quantitative relationship between the capacity load and the closing angle of suction valve is revealed.The capacity load and valve leakage rate show obvious different features in P-V diagrams,which makes it easier to define appropriate features for detecting cracked or broken reciprocating compressor valves under varying load conditions.A set of curves of compression work and discharge gas mass are obtained and a method for rating thermal performance of a compressor is presented using these curves.展开更多
The step load response of reciprocating engines is one of the key characteristics when considering its application in medium to large scale stationary power generation especially with islanded generation. This paper d...The step load response of reciprocating engines is one of the key characteristics when considering its application in medium to large scale stationary power generation especially with islanded generation. This paper discusses the impacts of power frequency deviation on the generators and electrical equipment in the network and presents the relationship between step load capabilities and generator operating parameters. For a power plant consisting of a number of generators both step load and power output requirements must be satisfied. An analysis method is proposed to facilitate the development of an operation strategy which can meet both step load and power demand requirements in the full load range.? Typical reciprocating engine step load curves are used to demonstrate the analysis method and the results are further optimised for lower operational cost. This analysis method provides a general approach to operation strategy of large reciprocating engines used in islanded power generation.展开更多
H-steel all-bolted connection steel frame structures with heat preservation and decoration composite wall boards were investigated and the seismic performances of three scaled specimens were studied.The failure modes,...H-steel all-bolted connection steel frame structures with heat preservation and decoration composite wall boards were investigated and the seismic performances of three scaled specimens were studied.The failure modes,hysteresis curves,bearing capacity,ductility,energy dissipation capacity,stiffness degradation and strain distribution were discussed.The calculation method of structural theoretical internal force was presented.The results showed that the overall structural seismic performance was better,and the structural ductility met the demands of elastic-plastic inter-story drift angle for seismic design.The H-steel weak-axis connection structure obtained better energy dissipation capacity,and its bearing capacity and stiffness were slightly different from the strong-axis connection.The heat preservation and decoration performance of composite wallboard and the all-bolted connection of the steel frame realized prefabrication during the whole construction period.The plastic hinge of the steel beam can be moved outwards because of the L-angles,which effectively avoids stress concentration in joint areas and expands the plastic hinge range.The errors between the theoretical structural capacity calculated by the plastic analysis method and the test results were within 2.44%.In addition,structural failure mechanisms and bearing capacities were verified by the finite element(FE)analysis,and the effects of the main parameters on the structures were investigated.The FE verification results were the same as in the test.The research results provide theoretical support and technical guidance for the application of thermal insulation and decorative composite wall panels in H-shaped steel all-bolted steel frames.展开更多
In the paper, the reciprocal theorem is applied to research on the bending of set square with one free oblique edge and two clamped edges under a concentrated load acting at any point. This method is simpler and general.
The reciprocal theorem was applied to solve the bending of the rectangular plates with each edges arbitrary a point supported under a concentrated load, the exact solutions and computation example are given.
基金the National Natural Science Foundation of China(No.52101343)State Key Laboratory of Compressor Technology(An Hui Laboratory of Compressor Technology)(No.SKL-YSJ201808/SKL-YSJ201911)。
文摘A research concerning the coupling conditions of gas leakage through suction valves and capacity regulation is performed in an industrial reciprocating compressor.Both internal flow and thermodynamic characteristic are discussed in detail.The results show that the capacity of compressor can be regulated steplessly by controlling suction valve closure moment.And then the quantitative relationship between the capacity load and the closing angle of suction valve is revealed.The capacity load and valve leakage rate show obvious different features in P-V diagrams,which makes it easier to define appropriate features for detecting cracked or broken reciprocating compressor valves under varying load conditions.A set of curves of compression work and discharge gas mass are obtained and a method for rating thermal performance of a compressor is presented using these curves.
文摘The step load response of reciprocating engines is one of the key characteristics when considering its application in medium to large scale stationary power generation especially with islanded generation. This paper discusses the impacts of power frequency deviation on the generators and electrical equipment in the network and presents the relationship between step load capabilities and generator operating parameters. For a power plant consisting of a number of generators both step load and power output requirements must be satisfied. An analysis method is proposed to facilitate the development of an operation strategy which can meet both step load and power demand requirements in the full load range.? Typical reciprocating engine step load curves are used to demonstrate the analysis method and the results are further optimised for lower operational cost. This analysis method provides a general approach to operation strategy of large reciprocating engines used in islanded power generation.
文摘H-steel all-bolted connection steel frame structures with heat preservation and decoration composite wall boards were investigated and the seismic performances of three scaled specimens were studied.The failure modes,hysteresis curves,bearing capacity,ductility,energy dissipation capacity,stiffness degradation and strain distribution were discussed.The calculation method of structural theoretical internal force was presented.The results showed that the overall structural seismic performance was better,and the structural ductility met the demands of elastic-plastic inter-story drift angle for seismic design.The H-steel weak-axis connection structure obtained better energy dissipation capacity,and its bearing capacity and stiffness were slightly different from the strong-axis connection.The heat preservation and decoration performance of composite wallboard and the all-bolted connection of the steel frame realized prefabrication during the whole construction period.The plastic hinge of the steel beam can be moved outwards because of the L-angles,which effectively avoids stress concentration in joint areas and expands the plastic hinge range.The errors between the theoretical structural capacity calculated by the plastic analysis method and the test results were within 2.44%.In addition,structural failure mechanisms and bearing capacities were verified by the finite element(FE)analysis,and the effects of the main parameters on the structures were investigated.The FE verification results were the same as in the test.The research results provide theoretical support and technical guidance for the application of thermal insulation and decorative composite wall panels in H-shaped steel all-bolted steel frames.
文摘In the paper, the reciprocal theorem is applied to research on the bending of set square with one free oblique edge and two clamped edges under a concentrated load acting at any point. This method is simpler and general.
文摘The reciprocal theorem was applied to solve the bending of the rectangular plates with each edges arbitrary a point supported under a concentrated load, the exact solutions and computation example are given.
