Micro segment analysis of supercritical methane thermal-hydraulic performance and pseudo-boiling in a PCHE straight channel

The printed circuit heat exchanger(PCHE) is receiving wide attention as a new kind of compact heat exchanger and is considered as a promising vaporizer in the LNG process. In this paper, a PCHE straight channel in the length of 500 mm is established, with a semicircular cross section in a diameter of 1.2 mm.Numerical simulation is employed to investigate the flow and heat transfer performance of supercritical methane in the channel. The pseudo-boiling theory is adopted and the liquid-like, two-phase-like, and vapor-like regimes are divided for supercritical methane to analyze the heat transfer and flow features.The results are presented in micro segment to show the local convective heat transfer coefficient and pressure drop. It shows that the convective heat transfer coefficient in segments along the channel has a significant peak feature near the pseudo-critical point and a heat transfer deterioration when the average fluid temperature in the segment is higher than the pseudo-critical point. The reason is explained with the generation of vapor-like film near the channel wall that the peak feature related to a nucleateboiling-like state and heat transfer deterioration related to a film-boiling-like state. The effects of parameters, including mass flow rate, pressure, and wall heat flux on flow and heat transfer were analyzed.In calculating of the averaged heat transfer coefficient of the whole channel, the traditional method shows significant deviation and the micro segment weighted average method is adopted. The pressure drop can mainly be affected by the mass flux and pressure and little affected by the wall heat flux. The peak of the convective heat transfer coefficient can only form at high mass flux, low wall heat flux, and near critical pressure, in which condition the nucleate-boiling-like state is easier to appear. Moreover,heat transfer deterioration will always appear, since the supercritical flow will finally develop into a filmboiling-like state. So heat transfer deterioration should be taken seriously in the design and safe operation of vaporizer PCHE. The study of this work clarified the local heat transfer and flow feature of supercritical methane in microchannel and contributed to the deep understanding of supercritical methane flow of the vaporization process in PCHE.

Extreme massive hydraulic fracturing in deep coalbed methane horizontal wells:A case study of the Linxing Block,eastern Ordos Basin,NW China

Deep coal seams show low permeability,low elastic modulus,high Poisson’s ratio,strong plasticity,high fracture initiation pressure,difficulty in fracture extension,and difficulty in proppants addition.We proposed the concept of large-scale stimulation by fracture network,balanced propagation and effective support of fracture network in fracturing design and developed the extreme massive hydraulic fracturing technique for deep coalbed methane(CBM)horizontal wells.This technique involves massive injection with high pumping rate+high-intensity proppant injection+perforation with equal apertures and limited flow+temporary plugging and diverting fractures+slick water with integrated variable viscosity+graded proppants with multiple sizes.The technique was applied in the pioneering test of a multi-stage fracturing horizontal well in deep CBM of Linxing Block,eastern margin of the Ordos Basin.The injection flow rate is 18 m^(3)/min,proppant intensity is 2.1 m^(3)/m,and fracturing fluid intensity is 16.5 m^(3)/m.After fracturing,a complex fracture network was formed,with an average fracture length of 205 m.The stimulated reservoir volume was 1987×10^(4)m^(3),and the peak gas production rate reached 6.0×10^(4)m^(3)/d,which achieved efficient development of deep CBM.

Non-thermal plasma enhanced catalytic conversion of methane into value added chemicals and fuels

Plasma catalysis has recently gained increased attention for its application in gas conversion,notably in processes like the dry reforming of methane aimed at transforming them into valuable chemicals and fuels.As this field is still in its early developmental stages,there is a crucial necessity to explore the synergistic mechanism between plasma and catalysts.The optimization of catalysts is imperative to improve their selectivity and conversion rates for desired products in a plasma environment.Additionally,delving into microscale investigations of plasma characteristics,such as electron temperature and the density of energetic species,is essential to enhance the stability and activity of catalysts.This review examines recent advancements in various methane conversion techniques,encompassing Dry Reforming of Methane,Steam Methane Reforming,Pa rtial Oxidation of Metha ne,and Methane Decomposition utilizing non-thermal dielectric barrier discharge(DBD)plasma.The aim is to gain a deeper understanding of plasma-catalyst interactions and to refine catalyst selection strategies for maximizing the production of desired products such as syngas,oxygenates,or higher hydrocarbons.The review delves into the catalytic mechanisms that delineate the synergistic effects between DBD plasma and catalyst in each technology,shedding light on the role of diverse catalytic properties in activating methane molecules-a pivotal step in hybrid plasma-catalytic reactions.Various approaches employed by researchers in exploring suitable catalysts and optimal reaction conditions to bolster CH_(4) conversion rates and selectivity using DBD plasma are discussed.Additionally,the review identifies gaps in the realm of plasma catalysis,underscoring the necessity for further research to fully understand the underlying principles of plasma and catalyst which are not trivial to uncover.

Theoretical insights into thermal transport and structural stability mechanisms of triaxial compressed methane hydrate

The heat transfer and stability of methane hydrate in reservoirs have a direct impact on the drilling and production efficiency of hydrate resources,especially in complex stress environments caused by formation subsidence.In this study,we investigated the thermal transport and structural stability of methane hydrate under triaxial compression using molecular dynamics simulations.The results suggest that the thermal conductivity of methane hydrate increases with increasing compression strain.Two phonon transport mechanisms were identified as factors enhancing thermal conductivity.At low compressive strains,a low-frequency phonon transport channel was established due to the overlap of phonon vibration peaks between methane and water molecules.At high compressive strains,the filling of larger phonon bandgaps facilitated the opening of more phonon transport channels.Additionally,we found that a strain of0.04 is a watershed point,where methane hydrate transitions from stable to unstable.Furthermore,a strain of0.06 marks the threshold at which the diffusion capacities of methane and water molecules are at their peaks.At a higher strain of0.08,the increased volume compression reduces the available space,limiting the diffusion ability of water and methane molecules within the hydrate.The synergistic effect of the strong diffusion ability and high probability of collision between atoms increases the thermal conductivity of hydrates during the unstable period compared to the stable period.Our findings offer valuable theoretical insights into the thermal conductivity and stability of methane hydrates in reservoir stress environments.

Rumen microbial degradation of bromoform from red seaweed(Asparagopsis taxiformis)and the impact on rumen fermentation and methanogenic archaea

Background The red macroalgae Asparagopsis is an effective methanogenesis inhibitor due to the presence of halogenated methane(CH_(4))analogues,primarily bromoform(CHBr_(3)).This study aimed to investigate the degradation process of CHBr3 from A taxiformis in the rumen and whether this process is diet-dependent.An in vitro batch culture system was used according to a 2×2 factorial design,assessing two A taxiformis inclusion rates[0(CTL)and 2%DM diet(AT)]and two diets[high-concentrate(HC)and high-forage diet(HF)].Incubations lasted for 72 h and samples of headspace and fermentation liquid were taken at 0,0.5,1,3,6,8,12,16,24,48 and 72 h to assess the pattern of degradation of CHBr_(3) into dibromomethane(CH_(2)Br_(2))and fermentation parameters.Additionally,an in vitro experiment with pure cultures of seven methanogens strains(Methanobrevibacter smithii,Methanobrevibacter ruminantium,Methanosphaera stadtmanae,Methanosarcina barkeri,Methanobrevibacter millerae,Methanorhermobacter wolfei and Methanobacterium mobile)was conducted to test the effects of increasing concentrations of CHBr3(0.4,2,10and 50μmol/L).Results The addition of AT significantly decreased CH_(4) production(P=0.002)and the acetate:propionate ratio(P=0.003)during a 72-h incubation.The concentrations of CHBr_(3) showed a rapid decrease with nearly 90%degraded within the first 3 h of incubation.On the contrary,CH_(2)Br_(2) concentration quickly increased during the first 6 h and then gradually decreased towards the end of the incubation.Neither CHBr_(3) degradation nor CH_(2)Br_(2) synthesis were affected by the type of diet used as substrate,suggesting that the fermentation rate is not a driving factor involved in CHBr_(3)degradation.The in vitro culture of methanogens showed a dose-response effect of CHBr3 by inhibiting the growth of M.smithii,M.ruminantium,M.stadtmanae,M.barkeri,M.millerae,M.wolfei,and M.mobile.Conclusions The present work demonstrated that CHBr_(3) from A.taxiformis is quickly degraded to CH_(2)Br_(2)in the rumen and that the fermentation rate promoted by different diets is not a driving factor involved in CHBr_(3)degradation.

Screening the optimal Co_(x)/CeO_(2)(110)(x=1–6)catalyst for methane activation in coalbed gas

The challenges posed by energy and environmental issues have forced mankind to explore and utilize unconventional energy sources.It is imperative to convert the abundant coalbed gas(CBG)into high value-added products,i.e.,selective and efficient conversion of methane from CBG.Methane activation,known as the“holy grail”,poses a challenge to the design and development of catalysts.The structural complexity of the active metal on the carrier is of particular concern.In this work,we have studied the nucleation growth of small Co clusters(up to Co_(6))on the surface of CeO_(2)(110)using density functional theory,from which a stable loaded Co/CeO_(2)(110)structure was selected to investigate the methane activation mechanism.Despite the relatively small size of the selected Co clusters,the obtained Co_(x)/CeO_(2)(110)exhibits interesting properties.The optimized Co_(5)/CeO_(2)(110)structure was selected as the optimal structure to study the activation mechanism of methane due to its competitive electronic structure,adsorption energy and binding energy.The energy barriers for the stepwise dissociation of methane to form CH3^(*),CH2^(*),CH^(*),and C^(*)radical fragments are 0.44,0.55,0.31,and 1.20 eV,respectively,indicating that CH^(*)dissociative dehydrogenation is the rate-determining step for the system under investigation here.This fundamental study of metal-support interactions based on Co growth on the CeO_(2)(110)surface contributes to the understanding of the essence of Co/CeO_(2) catalysts with promising catalytic behavior.It provides theoretical guidance for better designing the optimal Co/CeO_(2) catalyst for tailored catalytic reactions.

Advances in the studies of the supported ruthenium catalysts for CO_(2) methanation

CO_(2) methanation has a potential in the large-scale utilization of carbon dioxide.It has also been considered to be useful for the renewable energy storage.The commercial pipeline for natural gas transportation can be directly applied for the methane product of CO_(2) methanation.The supported ruthenium(Ru)catalyst has been confirmed to be active and stable for CO_(2) methanation with its high ability in the dissociation of hydrogen and the strong binding of carbon monoxide.CO_(2) methanation over the supported Ru catalyst is structure sensitive.The size of the Ru catalyst and the support have significant effects on the activity and the mechanism.A significant challenge re-mained is the structural controllable preparation of the supported Ru catalyst toward a sufficiently high low-temperature activity.In this review,the recent progresses in the investigations of the supported Ru catalysts for CO_(2) methanation are summarized.The challenges and the future devel-opments are also discussed.

Investigation of oxy-fuel combustion for methane and acid gas in a diffusion flame

Co-combustion of methane(CH4)and acid gas(AG)is required to sustain the temperature in Claus reaction furnace.In this study,oxy-fuel combustion of methane and acid gas has been experimentally studied in a diffusion flame.Three equivalence ratios(ER=1.0,1.5,2.0)and CH_(4)-addition ratios(CH_(4)/AG=0.3,0.5,0.7)were examined and the flame was interpreted by analyzing the distributions of the temperature and species concentration along central axial.CH_(4)-AG diffusion flame could be classified into three sections namely initial reaction,oxidation and complex reaction sections.Competitive oxidation of CH_(4)and H_(2)S was noted in the first section wherein H_(2)S was preferred and both were mainly proceeding decomposition and partial oxidation.SO_(2)was formed at oxidation section together with obvious presence of H2 and CO.However,H2 and CO were inclined to be sustained under fuel rich condition in the complex reaction section.Reducing ER and increasing CH4/AG contributed to higher temperature,H_(2)S and CH_(4)oxidation and CO_(2)reactivity.Hence a growing trend for CH_(4)and AG to convert into H_(2),CO and SO_(2)could be witnessed.And this factor enhanced the generation of CS2 and COS in the flame inner core by interactions of CH4 and CO_(2)with sulfur species.COS was formed through the interactions of CO and CO_(2)with sulfur species.The CS_(2)production directly relied on reaction of CH_(4)with sulfur species.The concentration of COS was greater than CS_(2)since CS_(2)was probably inhibited due to the presence of H_(2).COS and CS_(2)could be consumed by further oxidation or other complex reactions.

Methane Emission from Rice Fields:Necessity for Molecular Approach for Mitigation

Anthropogenic methane emissions are a leading cause of the increase in global averagetemperatures,often referred to as global warming.Flooded soils play a significant role in methaneproduction,where the anaerobic conditions promote the production of methane by methanogenicmicroorganisms.Rice fields contribute a considerable portion of agricultural methane emissions,as riceplants provide both factors that enhance and limit methane production.Rice plants harbor both methaneproducingand methane-oxidizing microorganisms.Exudates from rice roots provide source for methaneproduction,while oxygen delivered from the root aerenchyma enhances methane oxidation.Studies haveshown that the diversity of these microorganisms depends on rice cultivars with some genes characterizedas harboring specific groups of microorganisms related to methane emissions.However,there is still aneed for research to determine the balance between methane production and oxidation,as rice plantspossess the ability to regulate net methane production.Various agronomical practices,such as fertilizerand water management,have been employed to mitigate methane emissions.Nevertheless,studiescorrelating agronomic and chemical management of methane with productivity are limited.Moreover,evidences for breeding low-methane-emitting rice varieties are scattered largely due to the absence ofcoordinated breeding programs.Research has indicated that phenotypic characteristics,such as rootbiomass,shoot architecture,and aerenchyma,are highly correlated with methane emissions.This reviewdiscusses available studies that involve the correlation between plant characteristics and methaneemissions.It emphasizes the necessity and importance of breeding low-methane-emitting rice varieties inaddition to existing agronomic,biological,and chemical practices.The review also delves into the idealphenotypic and physiological characteristics of low-methane-emitting rice and potential breeding techniques,drawing from studies conducted with diverse varieties,mutants,and transgenic plants.

Study on the evolution of solid–liquid–gas in multi-scale pore methane in tectonic coal

The rich accumulation of methane(CH_(4))in tectonic coal layers poses a significant obstacle to the safe and efficient extraction of coal seams and coalbed methane.Tectonic coal samples from three geologically complex regions were selected,and the main results obtained by using a variety of research tools,such as physical tests,theoretical analyses,and numerical simulations,are as follows:22.4–62.5 nm is the joint segment of pore volume,and 26.7–100.7 nm is the joint segment of pore specific surface area.In the dynamic gas production process of tectonic coal pore structure,the adsorption method of methane molecules is“solid–liquid adsorption is the mainstay,and solid–gas adsorption coexists”.Methane stored in micropores with a pore size smaller than the jointed range is defined as solid-state pores.Pores within the jointed range,which transition from micropore filling to surface adsorption,are defined as gaseous pores.Pores outside the jointed range,where solid–liquid adsorption occurs,are defined as liquid pores.The evolution of pore structure affects the methane adsorption mode,which provides basic theoretical guidance for the development of coal seam resources.

Revisiting the mitigation of coke formation:Synergism between support&promoters'role toward robust yield in the CO_(2)reformation of methane

CO_(2)reformation of methane(CRM)and CO_(2)methanation are two interconnected processes with significant implications for greenhouse gas reduction and sustainable energy production for industrial purposes.While Nibased catalysis suffers from poor stability due to coke formation or sintering,we report a super stable remedy.The active sites of mesoporous MgO were loaded using wet impregnation.The incorporation of Ni and promoters altered the physical features of the catalysts.Sm–Ni/MgO showed the smallest crystallite size,specific surface area,and pore volume.The Sm–Ni/MgO catalyst was selected as the most suitable candidate for CRM,with 82%CH4 and H2/CO ratio of approximately 100%and also for CO_(2)methanation with the conversion of carbon dioxide(82%)and the selectivity toward methane reaches 100%at temperatures above 300ᵒC.Furthermore,the Sm–Ni/MgO catalyst was stable for 900 min of continuous reaction,without significant carbon deposition.This stability was largely due to the high oxygen mobility on the catalyst surface in the presence of Sm.Overall,we demonstrated the efficacy of using promoted Ni catalysts supported by mesoporous magnesia for the improved reformation of greenhouse gases.

Machine learning-driven optimization of plasma-catalytic dry reforming of methane

This study investigates the dry reformation of methane(DRM)over Ni/Al_(2)O_(3)catalysts in a dielectric barrier discharge(DBD)non-thermal plasma reactor.A novel hybrid machine learning(ML)model is developed to optimize the plasma-catalytic DRM reaction with limited experimental data.To address the non-linear and complex nature of the plasma-catalytic DRM process,the hybrid ML model integrates three well-established algorithms:regression trees,support vector regression,and artificial neural networks.A genetic algorithm(GA)is then used to optimize the hyperparameters of each algorithm within the hybrid ML model.The ML model achieved excellent agreement with the experimental data,demonstrating its efficacy in accurately predicting and optimizing the DRM process.The model was subsequently used to investigate the impact of various operating parameters on the plasma-catalytic DRM performance.We found that the optimal discharge power(20 W),CO_(2)/CH_(4)molar ratio(1.5),and Ni loading(7.8 wt%)resulted in the maximum energy yield at a total flow rate of∼51 mL/min.Furthermore,we investigated the relative significance of each operating parameter on the performance of the plasma-catalytic DRM process.The results show that the total flow rate had the greatest influence on the conversion,with a significance exceeding 35%for each output,while the Ni loading had the least impact on the overall reaction performance.This hybrid model demonstrates a remarkable ability to extract valuable insights from limited datasets,enabling the development and optimization of more efficient and selective plasma-catalytic chemical processes.

Zonal activation of molecular carbon dioxide and hydrogen over dual sites Ni-Co-MgO catalyst for CO_(2) methanation:Synergistic catalysis of Ni and Co species

An in-depth mechanism in zonal activation of CO_(2)and H2molecular over dual-active sites has not been revealed yet.Here,Ni-Co-MgO was rationally constructed to elucidate the CO_(2)methanation mechanism.The abundant surface nickel and cobalt components as active sites led to strong Ni-Co interaction with charge transfer from nickel to cobalt.Notably,electron-enriched Coδ-species participated in efficient chemisorption and activation of CO_(2)to generate monodentate carbonate.Simultaneously,plentiful available Ni0sites facilitated H2dissociation,thus CO_(2)and H2were smoothly activated at zones of Coδ-species and Ni0,respectively.Detailed in situ DRIFTS,quasi situ XPS,TPSR,and DFT calculations substantiated a new formate evolution mechanism via monodentate carbonate instead of traditional bidentate carbonate based on synergistic catalysis of Coδ-species and Ni0.The zonal activation of CO_(2)and H2by tuning electron behaviors of double-center catalysts can boost heterogeneous catalytic hydrogenation performance.

CO_(2)methanation boosted by support-size-dependent strong metal-support interaction and B-O-Ti component

Strong metal-support interaction(SMSI)has a great impact on the activity and selectivity of heterogeneous catalysts,which was usually adjusted by changing reduction temperature or processing catalyst in different atmosphere.However,few researches concentrate on modulating SMSI through regulating the structure of the support.Herein,we show how changing the surface environment of the anatase TiO_(2)(B–TiO_(2))can be used to modulate the SMSI.The moderate TiOx overlayer makes the Ni metal highly dispersed on the high specific surface area of support,resulting in a substantially enhanced CO_(2)methanation rate.Besides,a novel phenomenon was observed that boron dopants promote the for-mation of the B–O–Ti interface site,enhancing the catalytic performance of CO_(2)hydrogenation.DFT calculations confirm that the B–O–Ti structure facilitates the activation of CO_(2)and further hydrogenation to methane.

Regulating crystal phase of TiO_(2) to enhance catalytic activity of Ni/TiO_(2) for solar-driven dry reforming of methane

Ni/TiO_(2) catalyst is widely employed for photo-driven DRM reaction while the influence of crystal structure of TiO_(2) remains unclear.In this work,the rutile/anatase ratio in supports was successfully controlled by varying the calcination temperature of anatase-TiO_(2).Structural characterizations revealed that a distinct TiO_(x) coating on the Ni nanoparticles(NPs)was evident for Ni/TiO_(2)-700 catalyst due to strong metal-support interaction.It is observed that the TiOx overlayer gradually disappeared as the ratio of rutile/anatase increased,thereby enhancing the exposure of Ni active sites.The exposed Ni sites enhanced visible light absorption and boosted the dissociation capability of CH4,which led to the much elevated catalytic activity for Ni/TiO_(2)-950 in which rutile dominated.Therefore,the catalytic activity of solar-driven DRM reaction was significantly influenced by the rutile/anatase ratio.Ni/TiO_(2)-950,characterized by a predominant rutile phase,exhibited the highest DRM reactivity,with remarkable H_(2) and CO production rates reaching as high as 87.4 and 220.2 mmol/(g·h),respectively.These rates were approximately 257 and 130 times higher,respectively,compared to those obtained on Ni/TiO_(2)-700 with anatase.This study suggests that the optimization of crystal structure of TiO_(2) support can effectively enhance the performance of photothermal DRM reaction.

Excess pore pressure behavior and evolution in deep coalbed methane reservoirs

Deep coalbed methane(DCBM),an unconventional gas reservoir,has undergone significant advancements in recent years,sparking a growing interest in assessing pore pressure dynamics within these reservoirs.While some production data analysis techniques have been adapted from conventional oil and gas wells,there remains a gap in the understanding of pore pressure generation and evolution,particularly in wells subjected to large-scale hydraulic fracturing.To address this gap,a novel technique called excess pore pressure analysis(EPPA)has been introduced to the coal seam gas industry for the first time to our knowledge,which employs dual-phase flow principles based on consolidation theory.This technique focuses on the generation and dissipation for excess pore-water pressure(EPWP)and excess pore-gas pressure(EPGP)in stimulated deep coal reservoirs.Equations have been developed respectively and numerical solutions have been provided using the finite element method(FEM).Application of this model to a representative field example reveals that excess pore pressure arises from rapid loading,with overburden weight transferred under undrained condition due to intense hydraulic fracturing,which significantly redistributes the weight-bearing role from the solid coal structure to the injected fluid and liberated gas within artificial pores over a brief timespan.Furthermore,field application indicates that the dissipation of EPWP and EPGP can be actually considered as the process of well production,where methane and water are extracted from deep coalbed methane wells,leading to consolidation for the artificial reservoirs.Moreover,history matching results demonstrate that the excess-pressure model established in this study provides a better explanation for the declining trends observed in both gas and water production curves,compared to conventional practices in coalbed methane reservoir engineering and petroleum engineering.This research not only enhances the understanding of DCBM reservoir behavior but also offers insights applicable to production analysis in other unconventional resources reliant on hydraulic fracturing.

Investigations of methane adsorption characteristics on marine-continental transitional shales and gas storage capacity models considering pore evolution

Methane adsorption is a critical assessment of the gas storage capacity(GSC)of shales with geological conditions.Although the related research of marine shales has been well-illustrated,the methane adsorption of marine-continental transitional(MCT)shales is still ambiguous.In this study,a method of combining experimental data with analytical models was used to investigate the methane adsorption characteristics and GSC of MCT shales collected from the Qinshui Basin,China.The Ono-Kondo model was used to fit the adsorption data to obtain the adsorption parameters.Subsequently,the geological model of GSC based on pore evolution was constructed using a representative shale sample with a total organic carbon(TOC)content of 1.71%,and the effects of reservoir pressure coefficient and water saturation on GSC were explored.In experimental results,compared to the composition of the MCT shale,the pore structure dominates the methane adsorption,and meanwhile,the maturity mainly governs the pore structure.Besides,maturity in the middle-eastern region of the Qinshui Basin shows a strong positive correlation with burial depth.The two parameters,micropore pore volume and non-micropore surface area,induce a good fit for the adsorption capacity data of the shale.In simulation results,the depth,pressure coefficient,and water saturation of the shale all affect the GSC.It demonstrates a promising shale gas potential of the MCT shale in a deeper block,especially with low water saturation.Specifically,the economic feasibility of shale gas could be a major consideration for the shale with a depth of<800 m and/or water saturation>60%in the Yushe-Wuxiang area.This study provides a valuable reference for the reservoir evaluation and favorable block search of MCT shale gas.

Remarkably Enhanced Methane Sensing Performance at Room Temperature via Constructing a Self-Assembled Mulberry-Like ZnO/SnO_(2) Hierarchical Structure

Development of metal oxide semiconductors-based methane sensors with good response and low power consumption is one of the major challenges to realize the real-time monitoring of methane leakage.In this work,a self-assembled mulberry-like ZnO/SnO_(2)hierarchical structure is constructed by a two-step hydrothermal method.The resultant sensor works at room temperature with excellent response of~56.1%to 2000 ppm CH_(4)at 55%relative humidity.It is found that the strain induced at the ZnO/SnO_(2)interface greatly enhances the piezoelectric polarization on the ZnO surface and that the band bending results in the accumulation of chemically adsorbed O_(2)^(-)ions close to the interface,leading to significant improvement in the sensing performance of the methane gas sensor at room temperature.

A novel metal-free porous covalent organic polymer for efficient room-temperature photocatalytic CO_(2) reduction via dry-reforming of methane

At room temperature,the conversion of greenhouse gases into valuable chemicals using metal-free catalysts for dry reforming of methane(DRM) is quite promising and challenging.Herein,we developed a novel covalent organic porous polymer (TPE-COP) with rapid charge separation of the electron–hole pairs for DRM driven by visible light at room temperature,which can efficiently generate syngas (CO and H_(2)).Both electron donor (tris(4-aminophenyl)amine,TAPA) and acceptor (4,4',4'',4'''-((1 E,1'E,1''E,1'''E)-(ethene-1,1,2,2-tetrayltetrakis (benzene-4,1-diyl))tetrakis (ethene-2,1-diyl))tetrakis (1-(4-formylbenzyl)quinolin-1-ium),TPE-CHO) were existed in TPE-COP,in which the push–pull effect between them promoted the separation of photogenerated electron–hole,thus greatly improving the photocatalytic activity.Density functional theory (DFT) simulation results show that TPE-COP can form charge-separating species under light irradiation,leading to electrons accumulation in TPE-CHO unit and holes in TAPA,and thus efficiently initiating DRM.After 20 h illumination,the photocatalytic results show that the yields reach 1123.6 and 30.8μmol g^(-1)for CO and H_(2),respectively,which are significantly higher than those of TPE-CHO small molecules.This excellent result is mainly due to the increase of specific surface area,the enhancement of light absorption capacity,and the improvement of photoelectron-generating efficiency after the formation of COP.Overall,this work contributes to understanding the advantages of COP materials for photocatalysis and fundamentally pushes metal-free catalysts into the door of DRM field.

Ca and Sr co-doping induced oxygen vacancies in 3DOM La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)catalysts for boosting low-temperature oxidative coupling of methane

It is urgent to develop catalysts with application potential for oxidative coupling of methane(OCM)at relatively lower temperature.Herein,three-dimensional ordered macro porous(3 DOM)La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)(A_(2)B_(2)O_(7)-type)catalysts with disordered defective cubic fluorite phased structure were successfully prepared by a colloidal crystal template method.3DOM structure promotes the accessibility of the gaseous reactants(O2and CH4)to the active sites.The co-doping of Ca and Sr ions in La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)catalysts improved the formation of oxygen vacancies,thereby leading to increased density of surface-active oxygen species(O_(2)^(-))for the activation of CH4and the formation of C2products(C2H6and C2H4).3DOM La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)catalysts exhibit high catalytic activity for OCM at low temperature.3DOM La1.7Sr0.3Ce1.7Ca0.3O7-δcatalyst with the highest density of O_(2)^(-)species exhibited the highest catalytic activity for low-temperature OCM,i.e.,its CH4conversion,selectivity and yield of C2products at 650℃are 32.2%,66.1%and 21.3%,respectively.The mechanism was proposed that the increase in surface oxygen vacancies induced by the co-doping of Ca and Sr ions boosts the key step of C-H bond breaking and C-C bond coupling in catalyzing low-temperature OCM.It is meaningful for the development of the low-temperature and high-efficient catalysts for OCM reaction in practical application.