Experimental study on preferential solution flow during dump leaching of low-grade ores

The phenomenon of preferential solution flow during dump leaching of low-grade ores was studied.The formative mechanism of preferential solution flow was investigated through analyzing the relationship between permeability and ore diameter,and the relationship between surface tension and ore diameter.The preferential solution flow happened within the fine ore area when the dump was unsaturated.And it could happen within the coarse ore area when the dump became saturated.The results of experiment show that the outflow of coarse ore area increases sharply with higher applied rate.The outflow of fine ore area is greater than that of coarse ore area when the applied rate is below 3.2 L/min,and the preferential solution flow happens in fine ore area.But the preferential solution flow happens in coarse ore area when the applied rate is higher than 3.2 L/min.The result of the experiment is consistent with the mechanism analyzing.

Leaching kinetics of low-grade copper ore containing calcium-magnesium carbonate in ammonia-ammonium sulfate solution with persulfate

The leaching kinetics of copper from low-grade copper ore was investigated in ammonia-ammonium sulfate solution with sodium persulfate. The effect parameters of stirring speed, temperature, particle size, concentrations of ammonia, ammonium sulfate and sodium persulfate were determined. The results show that the leaching rate is nearly independent of agitation above 300 r/min and increases with the increase of temperature, concentrations of ammonia, ammonium sulfate and sodium persulfate. The EDS analysis and phase quantitative analysis of the residues indicate that bornite can be dissolved by persulfate oxidization. The leaching kinetics with activation energy of 22.91 kJ/mol was analyzed by using a new shrinking core model （SCM） in which both the interfacial transfer and diffusion across the product layer affect the leaching rate. A semi-empirical rate equation was obtained to describe the leaching process and the empirical reaction orders with respect to the concentrations of ammonia, ammonium sulfate and sodium persulfate are 0.5, 1.2 and 0.5, respectively.

Manganese extraction by reduction-acid leaching from low-grade manganese oxide ores using CaS as reductant

The extraction of manganese from low-grade manganese oxide ores using Ca S derived from Ca SO4 as reductant was investigated. The effects of mass ratio of Ca S to ore, reduction temperature, reduction time, liquid to solid ratio（L/S ratio）, stirring speed, leaching temperature, leaching time and H2SO4 concentration on the leaching rates of Mn and Fe during the reduction–acid leaching process were discussed. The leaching rates of 96.47% for Mn and 19.24% for Fe were obtained under the optimized conditions of mass ratio of Ca S to manganese oxide ore 1：6.7, L/S ratio 5：1, stirring speed 300 r/min, reduction temperature of 95 °C for 2.0 h in the reduction process and leaching stirring speed of 200 r/min, H2SO4 concentration of 1.5 mol/L, leaching temperature of 80 °C for 5 min in the leaching process. In addition, this process can be employed in the recovery of manganese from various manganese oxide ores, and Mn leaching rate above 95% is obtained.

Coal-based reduction mechanism of low-grade laterite ore

A low-grade nickel laterite ore was reduced at different reduction temperatures. The morphology of metallic particles was investigated by scanning electron microscopy （SEM） and energy dispersive spectroscopy （EDS）. Experimental results indicate that the metallic nickel and iron gradually assemble and grow into larger spherical particles with increasing temperature and prolonging time. After reduction, the nickel laterite ore obviously changes into two parts of Fe-Ni metallic particles and slag matrix. An obvious relationship is found between the reduction of iron magnesium olivine and its crystal chemical properties. The nickel and iron oxides are reduced to metallic by reductant, and the lattice of olivine is destroyed. The entire reduction process is comprised of oxide reduction and metallic phase growth.

Extraction of valuable metals from low-grade nickeliferous laterite ore by reduction roasting-ammonia leaching method

Nickel and cobalt were extracted from low-grade nickeliferous laterite ore using a reduction roasting-ammonia leaching method.The reduction roasting-ammonia leaching experimental tests were chiefly introduced,by which fine coal was used as a reductant.The results show that the optimum process conditions are confirmed as follows:in reduction roasting process,the mass fraction of reductant in the ore is 10%,roasting time is 120 min,roasting temperature is 1 023-1 073 K;in ammonia leaching process,the liquid-to-solid ratio is 4:1(mL/g),leaching temperature is 313 K,leaching time is 120 min,and concentration ratio of NH3 to CO2 is 90 g/L:60 g/L.Under the optimum conditions,leaching efficiencies of nickel and cobalt are 86.25% and 60.84%,respectively.Therefore,nickel and cobalt can be effectively reclaimed,and the leaching agent can be also recycled at room temperature and normal pressure.

Transformation and leaching kinetics of silicon from low-grade nickel laterite ore by pre-roasting and alkaline leaching process

The mineralogical phase transformation of a low-grade nickel laterite ore during pre-roasting process and the extraction of silicon during alkaline leaching process were investigated.The results indicate that the reaction activity of nickel ores is effectively improved by pre-roasting at650°C for2h,because of the transformation of lizardite into magnesium olivine and protoenstatite.When finely ground ore samples(44-61μm)pre-roasted firstly react with sodium hydroxide solution(60g/L)with a solid/liquid ratio of1:5at140°C for120min,the extraction of silicon can reach89.89%,and the other valuable elements of magnesium,iron and nickel are accumulated in the solid residues.The leaching kinetics of nickel laterite ore can be described successfully by the diffusion through the product layer control model.The activation energy is calculated to be11.63kJ/mol and the kinetics equation can be expressed as1-3(1-x)2/3+2(1-x)=13.53×10-2exp[-11.63/(RT)]t.

Recovery of Zn, Pb, Fe and Si from a low-grade mining ore by sulfidation roasting-beneficiation-leaching processes

To recover Zn, Pb, Fe and Si from a low-grade mining ore in the Lanping basin, Yunnan Province, China, a novel technology using the roasting with pyrite and carbon followed by beneficiation and hydrochloric acid leaching was proposed. Firstly, several factors such as pyrite dosage, roasting temperature, carbon powder dosage, holding time and particle size affecting on the flotation performance of Zn(Pb) and magnetic separation performance of Fe were simultaneously examined and the optimum process parameters were determined. A flotation concentrate, containing 17.46% Zn and 3.93% Pb, was obtained, and the Zn and Pb recoveries were 86.04% and 69.08%, respectively. The obtained flotation tailing was concentrated by a low-intensity magnetic separator. The grade of iron increased from 5.45% to 43.45% and the recovery of iron reached 64.87%. Hydrochloric acid leaching was then carried out for the magnetic separation tailing and a raw quartz concentrate containing 81.05% SiO2 was obtained. To further interpret the sulfidation mechanism of smithsonite, surface morphology and component of the sample before and after reactions were characterized by XRD and EPMA-EDS. The aim was to achieve the comprehensive utilization of the low-grade mining ore.

Leaching kinetics of low-grade copper ore with high-alkality gangues in ammonia-ammonium sulphate solution

The leaching kinetics of low-grade copper ore with high-alkality gangues was studied in ammonia-ammonium sulphate solution.The main parameters,such as ammonia and ammonium sulphate concentrations,particle size,solid-to-liquid ratio and reaction temperature,were chosen in the experiments.The results show that the increase of temperature,concentrations of ammonia and ammonium sulphate is propitious to the leaching rate of copper ore.The leaching rate increases with the decrease of particle size and solid-to-liquid ratio.The leaching rate is controlled by the diffusion through the ash layer and the activation energy is determined to be 25.54 kJ/mol.A semi-empirical equation was proposed to describe the leaching kinetics.

Hydrometallurgical leaching and kinetic modeling of low-grade manganese ore with banana peel in sulfuric acid

Manganese was leached from a low-grade manganese ore(LGMO)using banana peel as the reductant in a dilute sulfuric acid medium.The effects of banana peel amount,H2SO4 concentration,reaction temperature,and time on Mn leaching from the complex LGMO were studied.A leaching efficiency of~98%was achieved at a leaching time of 2 h,banana peel amount of 4 g,leaching temperature of 120°C,manganese ore amount of 5 g,and sulfuric acid concentration of 15vol%.The phase,microstructural,and chemical analyses of LGMO samples before and after the leaching process confirmed the successful leaching of manganese.Furthermore,the leaching process followed the shrinking core model and the leaching rate was controlled by a surface chemical reaction(1−(1−x)^1/3=kt)mechanism with an apparent activation energy of 40.19 kJ·mol^−1.

Acid equilibrium during bioleaching of alkaline low-grade sulfide copper ore

This article reports the study on acid equilibrium during bioleaching of alkaline low-grade copper sulfide ore. Adding auxiliary agents 1# （sulfur） and 2# （pyrite） makes bacterial leaching of copper and acid production carried out simultaneously because the auxiliary agents can be oxidized by bacteria and the oxidation products involve acid. The acid required for dissolving alkaline gangue during bacterial leaching is produced, and acid equilibrium is reached during the ore bio-leaching. The recovery of copper reaches more than 95%.

Co-extraction of valuable metals and kinetics analysis in chlorination process of low-grade nickel-copper sulfide ore

To efficiently co-extract Ni and Cu from low-grade nickel-copper sulfide ore,chlorination roasting with NH;Cl followed by a water leaching process was investigated.The results show that 98.4%Ni and 98.5%Cu can be synchronously extracted when the ore particle size is 75-80μm,the roasting time is 2 h,the mass ratio of NH;Cl to ore is 1.6:1 and the roasting temperature is 550°C.The evolution behavior of various minerals was elucidated using X-ray diffraction(XRD)coupled with scanning electron microscopy(SEM).The kinetics of the chlorination process based on the differential thermal and thermogravimetric analysis(DTA-TG)data was analyzed by Kissinger method and Flynn-Wall-Ozawa(FWO)method.The chlorination process of low-grade nickel-copper sulfide ore mainly contains two stages:the decomposition of NH;Cl and the chlorination of ore.The maximum apparent activation energies(Ea)at two stages are determined to be 114.8 and 144.6 kJ/mol,respectively.The condensed product of exhaust gas is determined to be ammonium chloride,which can be recycled as the reactant again,making the process economic and clean.

Improved recovery of a low-grade refractory gold ore using flotation–preoxidation–cyanidation methods

In this work, different flotation–preoxidation–cyanidation methods are considered for treating a lowgrade refractory gold ore. On the one hand, the results of selective flotation show that 22% and 31.1%of total Sb and As, respectively, remained in the final tailings and only about 28% of the total Au remained for further cyanidation processes. On the other hand, in bulk method of flotation the maximum Au recovery of 90.6% achieved after 60 min of flotation at the grind size with K80 of 146 micron. In addition, the bulk flotation method resulted in the concentrate with low concentrations of Sb and As elements. To improve the recovery of low-grade refractory gold ores, flotation should be followed by roasting, biological, or pressure oxidation processes so that the gold could be liberated prior to cyanidation processes. It is also found that the pressure oxidation pre-treatment of the concentrates prior to cyanidation may yield high gold recoveries of over than 83%. In these processes, recoveries are controlled by the temperature and the oxygen partial pressure in the solvent. However, by utilizing the bio-oxidation technique, the oxidation of sulfur to sulfate cannot be completed and, consequently, the gold recovery may be limited to only 72.2%.

Study on hydrometallurgical process and kinetics of manganese extraction from low-grade manganese carbonate ores

In order to utilize low-grade manganese ore resources effectively, a hydrometallurgical process was developed for manganese extraction in dilute sulfuric acid medium, and the kinetics of leaching manga- nese was also investigated. At room temperature, manganese from low-grade manganese carbonate ores was extracted by sulfuric acid leaching without reductants. During the extracting process, single-factor analysis method was used to evaluate the effects of grinding fineness, sulfuric acid concentration, liquid-to-solid ratio, agitation rate and leaching time on the leaching efficiencies of Mn and Fe. The optimal leaching conditions are determined as coarse particles of below 2 mm size （without ball-milling）, sulfuric acid concentration of 0.86 mol/L, liquid-to-solid ratio of 5：1, agitation rate of 150 r/rain and leaching for 180 min at room temperature. Under the optimal conditions, the leaching efficiencies of Mn and Fe are 96.21g and 13.35%, respectively. In addition, through the experiments at different temper- atures, it is found that the leaching process follows the shrinking core model under the conditions of changing acid concentration and intermittent reaction device. Moreover, the apparent activations of effective diffusion and chemical reaction in the kinetic model are calculated to be 18.83 and 27.15 kJ/mol, respectively.

Recovery of zinc from low-grade zinc oxide ores by solvent extraction

The recovery of zinc from low-grade zinc oxide ores with solvent extraction-electrowinning technique was investigated by using D2EHPA as extractant and 260 # kerosene as diluent. The results show that it is possible to selectively leach zinc from the ores by heap leaching. The zinc concentration of leach solution in the first leaching cycle is 32.57 g/L, and in the sixteenth cycle the zinc concentration is 8.27g/L after solvent extraction. The leaching solution is subjected to solvent extraction, scrubbing and selective stripping for enrichment of zinc and removal of impurities. The pregnant zinc sulfate solution produced from the stripping cycle is suitable for zinc electrowinning. Extra-pure zinc metal was obtained in the electrowinning test under conventional conditions.

Recovery of valuable metals from a low-grade nickel ore using an ammonium sulfate roasting-leaching process

Metal leaching from a low-grade nickel ore was investigated using an ammonium sulfate roasting-water leaching process. The nickel ore was mixed with ammonium sulfate, followed by roasting and finally leaching with water. During the process the effects of the amotmt of ammonium sulfate, roasting temperature, and roasting time on the leaching recovery of metal elements were analyzed. The optimum technological parameters were determined as follows： ammonium sulfate/ore ratio, 0.8 g/g; roasting temperature, 400℃; and roasting time, 2 h. Under the optimum condition the leaching recoveries ofNi, Cu, Fe, and Mg were 83.48%, 76.24%, 56.43%, and 62.15%, respectively. Furthermore, the dissolution kinetics of Ni and Mg from the nickel ore was studied. The apparent activation energies for the leaching reaction of Ni and Mg were 18.782 and 10.038 kJ.mo1-1, which were consistent with the values of diffusion control reactions. Therefore, the results demonstrated that the leaching recoveries of Ni and Mg were controlled by diffusion.

Microwave-assisted reduction roasting–magnetic separation studies of two mineralogically different low-grade iron ores

The microwave-assisted reduction behaviours of two low-grade iron ores having a similar Fe content of 49wt%but distinctly different mineralogical and liberation characteristics were studied.Their performances in terms of the iron grade and recovery as obtained from statistically designed microwave(MW)roasting followed by low-intensity magnetic separation(LIMS)experiments were compared.At respective optimum conditions,the titano-magnetite ore(O1)could yield an iron concentrate of 62.57%Fe grade and 60.01%Fe recovery,while the goethitic ore(O2)could be upgraded to a concentrate of 64.4%Fe grade and 33.3%Fe recovery.Compared with the goethitic ore,the titanomagnetite ore responded better to MW heating.The characterization studies of the feed and roasted products obtained at different power and time conditions using X-ray diffraction,optical microscopy,vibrating-sample magnetometry,and electron-probe microanalysis explain the sequential reduction in the iron oxide phases.Finally,taking advantage of the MW absorbing character of the titano-magnetite ore,a blend of the same with the goethite-rich ore at a weight ratio of 60:40(O2:O1)was subjected to MW roasting that resulted in a concentrate of 61.57%Fe grade with a Fe recovery of 64.47%.

Bioleaching of low-grade copper sulfide ores by Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans

The grown conditions of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans were investigated,and then experiments were conducted to research the bioleaching behaviors of crude ore of copper sulfide and hand-picked concentrates of chalcopyrite by Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans.The experimental results show that the bacteria grow best when the temperature is(30±1) °C and the pH value is 2.0.The bacteria concentration is 2.24×107 mL-1 in this condition.It is found that the copper extraction yield is affected by the inoculum size and the pulp density and the extraction yield increases as the inoculum size grows.The bioleaching rates reach their highest point in sulfide copper and chalcopyrite with a pulp density of 5% and 10%,respectively.Column flotation experiments of low-grade copper sulfide ores show that the bioleaching recovery reaches nearly 45% after 75 days.

Kinetic Investigations on the Leaching of Niobium from a Low-Grade Niobium-Tantalum Ore by Concentrated KOH Solution

The leaching kinetics of niobium from a low-grade niobium-tantalum ore by concentrated KOH solu-tion under atmospheric pressure has been studied. Significant effects of reaction temperature, KOH concentration, stirring speed, particle size and inass ratio of alkali-to-ore on the dissolution rate of niobium were examined. The experimental data of the leaching rates and the observed effects of the relevant operating variables were well in-terpreted with a shrinking core model under diffusion control. By using the Arrhenius expression, the apparent activation energy for the dissolution of niobium was evaluated. Finally, on the base of the shrinking core model, the rate equation was established.

Relationship between process mineralogical characterization and beneficiability of low-grade laterite nickel ore

Process mineralogy of low-grade laterite nickel ore in Indonesia was systematically characterized and the beneficiation process of mineral components such as limonite,serpentine and chromite was studied on the basis of process mineralogy.The results show that the low-grade laterite nickel ore is a typical weathering sedimentary metamorphic oxidized ore,with the main valuable elements of Ni,Co and Cr and the main mineral components of limonite,serpentine,chromite,etc.There is no independent carrier mineral of Ni and Co in the raw ore,and the occurrence states of Ni and Co are relatively dispersed.For the limonite in laterite nickel mine,the nickel bearing magnetite concentrate with nickel grade of 1.98%and recovery rate of 88.42%can be obtained by reduction roasting magnetic separation process.For the serpentine in laterite nickel mine,the cobalt bearing concentrate with Co grade of 0.17%and recovery rate of 23.17%can be obtained by positive and reverse flotation process.A chromium concentrate containing 35.17%Cr_(2)O_(3) and a recovery of 33.42%can be obtained by using the combined process of coarse and fine classification and gravity and magnetic.

Effect of desliming on the magnetic separation of low-grade ferruginous manganese ore

In the present investigation, magnetic separation studies using an induced roll magnetic separator were conducted to beneficiate low-grade ferruginous manganese ore. The feed ore was assayed to contain 22.4% Mn and 35.9% SiO2, with a manganese-to-iron mass ratio （Mn：Fe ratio） of 1.6. This ore was characterized in detail using different techniques, including quantitative evaluation of minerals by scan- ning electron microscopy, which revealed that the ore is extremely siliceous in nature and that the associated gangue minerals are more or less evenly distributed in almost all of the size fractions in major proportion. Magnetic separation studies were conducted on both the as-received ore fines and the classified fines to enrich their manganese content and Mn：Fe ratio. The results indicated that the efficiency of separation for deslimed fines was better than that for the treated unclassified bulk sample. On the basis of these results, we proposed a proc- ess flow sheet for the beneficiation of low-grade manganese ore fines using a Floatex density separator as a pre-concentrator followed by two-stage magnetic separation. The overall recovery of manganese in the final product from the proposed flow sheet is 44.7% with an assay value of 45.8% and the Mn：Fe ratio of 3.1.