Performance investigation of a low-power Hall thruster fed on iodine propellant

The common propellants used for electric thrusters, such as xenon and krypton, are rare, expensive,and difficult to acquire. Solid iodine attracts much attention with the advantages of low cost,extensive availability, low vapor pressure, and ionization potential. The performance of a lowpower iodine-fed Hall thruster matched with a xenon-fed cathode is investigated across a broad range of operation conditions. Regulation of the iodine vapor's mass flow rates is stably achieved by using a temperature control method of the iodine reservoir. The thrust measurements are finished utilizing a thrust target during the tests. Results show that thrust and anode-specific impulse increase approximately linearly with the increasing iodine mass flow rate.At the nominal power of 200 W class, iodine mass flow rates are 0.62 and 0.93 mg/s, thrusts are7.19 and 7.58 m N, anode specific impulses are 1184 and 826 s, anode efficiencies are 20.8%and 14.5%, and thrust to power ratios are 35.9 and 37.9 m N/k W under the conditions of 250 V,0.8 A and 200 V, 1.0 A, respectively. The operating characteristics of iodine-fed Hall thruster are analyzed in different states. Further work on the measurements of plasma characteristics and experimental optimization will be carried out.

The far-field plasma characteristics of LHT40 low-power Hall thruster for commercial aerospace applications

To achieve a better insight into the far-field plasma spatial distribution and evolution characteristics of the 300 W class low-power Hall thruster(LHT)for commercial aerospace applications,a dedicated and integrated plasma diagnostic system composed of seventeen Faraday cups(FC)and two triple Langmuir probes(TLP)is established to investigate the timeaveraged in situ spatial distribution characteristics of far-field ions and electrons.The ion current density(ICD),plasma potential,plasma density,and electron temperature at 1000 mm downstream of 300 W class LHT for commercial aerospace applications in the azimuthal angle range of-90°to 90°were investigated under the conditions of different anode mass flow rates and discharge voltages.The results demonstrated that ICD,beam divergence angle,and mass utilization efficiency increased with increasing anode mass rate.The double-wings phenomenon was observed in the spatial distribution of ICD at large angles from the thruster axis,which is attributed to charge exchange collisions at increasing vacuum backpressure.The plasma electron temperature,electron density,and plasma potential parameters derived from the TLP decreased rapidly in the angle range from 0°to 30°and did not exhibit significant variations above 30°,which was also in good agreement with the results of the measured divergence angle of the FC.The discrepancy of average ion speed was calculated.The maximum error is better than 31.5%which checks the consistency between the TLP’s results and that of FC to some extent.

Simulation of the effect of a magnetically insulated anode on a low-power cylindrical Hall thruster

The intersection point of the characteristic magnetic field line（CMFL） crossing the anode boundary with the discharge channel wall, and its influence on thruster performance and the energy and flux of ions bombarding the channel wall, have been studied numerically. The simulation results demonstrate that with the increase in distance from the crossover point of the CMFL with the channel wall to the bottom of the thruster channel, the ionization rate in the discharge channel gradually increases; meanwhile, the ion energy and ion current density bombarding the channel wall decreases. When the point of the CMFL with the channel wall is at the channel outlet, the thrust, specific impulse, and efficiency are at a maximum, while the ion energy and ion current density bombarding the channel wall are at a minimum. Therefore, to improve the performance and lifetime of the thruster, it is important to control the point of intersection of the CMFL with the channel wall.

Thrust estimate method of an on-orbit Hall thruster using Hall drift current

In order to realize the thrust estimation of the Hall thruster during its flight mission,this study establishes an estimation method based on measurement of the Hall drift current.In this method,the Hall drift current is calculated from an inverse magnetostatic problem,which is formulated according to its induced magnetic flux density detected by sensors,and then the thrust is estimated by multiplying the Hall drift current with the characteristic magnetic flux density of the thruster itself.In addition,a three-wire torsion pendulum micro-thrust measurement system is utilized to verify the estimate values obtained from the proposed method.The errors were found to be less than 8%when the discharge voltage ranged from 250 V to 350 V and the anode flow rate ranged from 30 sccm to 50 sccm,indicating the possibility that the proposed thrust estimate method could be practically applied.Moreover,the measurement accuracy of the magnetic flux density is suggested to be lower than 0.015 mT and improvement on the inverse problem solution is required in the future.

Influence of the position relationship between the cathode and magnetic separatrix on the discharge process of a Hall thruster

Previous studies have shown that there is an obvious coupling relationship between the installation location of the external cathode and the magnetic separatrix in the plume region of a Hall thruster.In this paper,the particle-in-cell simulation method is used to compare the thruster discharge process under the conditions of different position relationships between the cathode and the magnetic separatrix.By comparing the distribution of electron conduction,potential,plasma density and other microscopic parameters,we try to explain the formation mechanism of the discharge difference.The simulation results show that the cathode inside and outside the magnetic separatrix has a significant effect on the distribution of potential and plasma density.When the cathode is located on the outer side of the magnetic separatrix,the potential above the plume region is relatively low,and there is a strong potential gradient above the plume region.This potential gradient is more conducive to the radial diffusion of ions above the plume,which is the main reason for the strong divergence of the plume.The distribution of ion density is also consistent with the distribution of potential.When the cathode is located on the outer side of the magnetic separatrix,the radial diffusion of ions in the plume region is enhanced.Meanwhile,by comparing the results of electron conduction,it is found that the traiectories of electrons emitted from the cathode are significantly different between the inner and outer sides of the magnetic separatrix.This is mainly because the electrons are affected by the magnetic mirror effect of the magnetic tip,which makes it difficult for the electrons to move across the magnetic separatrix.This is the main reason for the difference in potential distribution.In this paper,the simulation results of macroscopic parameters under several conditions are also compared,and they are consistent with the experimental results.The cathode is located on the inner side of the magnetic separatrix,which can effectively reduce the plume divergence angle and improve the thrust.In this paper,the cathode moves from R=50 mm to R=35 mm along the radial direction,the thrust increases by 3.6 mN and the plume divergence angle decreases by 23.77%.Combined with the comparison of the ionization region and the peak ion density,it is found that the main reason for the change in thrust is the change in the radial diffusion of ions in the plume region.

Growth mechanism and characteristics of electron drift instability in Hall thruster with different propellant types

The existence of a significant electron drift instability(EDI) in the Hall thruster is considered as one of the possible causes of the abnormal increase in axial electron mobility near the outlet of the channel. In recent years, extensive simulation research on the characteristics of EDI has been conducted, but the excitation mechanism and growth mechanism of EDI in linear stage and nonlinear stage remain unclear. In this work, a one-dimensional PIC model in the azimuthal direction of the thruster near-exit region is established to gain further insights into the mechanism of the EDI in detail, and the effects of different types of propellants on EDI characteristics are discussed. The changes in axial electron transport caused by EDI under different types of propellants and electromagnetic field strengths are also examined. The results indicate that EDI undergoes a short linear growth phase before transitioning to the nonlinear phase and finally reaching saturation through the ion Landau damping. The EDI drives a significant ion heating in the azimuthal direction through electron–ion friction before entering the quasi-steady state, which increases the axial mobility of the electrons. Using lighter atomic weight propellant can effectively suppress the oscillation amplitude of EDI, but it will increase the linear growth rate, frequency, and phase velocity of EDI. Compared with the classical mobility, the axial electron mobility under the EDI increases by three orders of magnitude, which is consistent with experimental phenomena. The change of propellant type is insufficient to significantly change the axial electron mobility. It is also found that the collisions between electrons and neutral gasescan significantly affect the axial electron mobility under the influence of EDI, and lead the strength of the electric field to increase and the strength of the magnetic field to decrease, thereby both effectively suppressing the axial transport of electrons.

Influence of acceleration stage electrode voltage on the performance of double-stage Hall effect thruster with adjustable zero magnetic point

The configuration of electrode voltage and zero magnetic point position has a significant impact on the performance of the double-stage Hall effect thruster. A 2D-3V model is established based on the two-magnetic peak type double-stage Hall thruster configuration, and a particle-in-cell simulation is carried out to investigate the influences of both acceleration electrode voltage value and zero magnetic point position on the thruster discharge characteristics and performances.The results indicate that increasing the acceleration voltage leads to a larger potential drop in the acceleration stage, allowing ions to gain higher energy, while electrons are easily absorbed by the intermediate electrode, resulting in a decrease in the anode current and ionization rate. When the acceleration voltage reaches 500 V, the thrust and efficiency are maximized, resulting in a 15%increase in efficiency. After the acceleration voltage exceeds 500 V, a potential barrier forms within the channel, leading to a decrease in thruster efficiency. Further study shows that as the second zero magnetic point moves towards the outlet of the channel, more electrons easily traverse the zero magnetic field region, participating in the ionization. The increase in the ionization rate leads to a gradual enhancement in both thrust and efficiency.

Experimental and numerical simulation study of the effect for the anode positions on the discharge characteristics of 300W class low power Hall thrusters

Low-power Hall thruster(LHT) generally has poor discharge efficiency characteristics due to the large surface-to-volume ratio.Aiming to further refine and improve the performance of 300 W class LHT in terms of thrust and efficiency,and to obtain the most optimal operating point,the experimental study of the discharge characteristics for three different anode positions was conducted under the operation of various discharge voltages(100-400 V) and anode mass flow rates(0.65 mg·s-1and 0.95 mg·s-1).The experimental results indicated that the thruster has the most excellent performance in terms of thrust and efficiency etc at a channel length of 27 mm for identical operating conditions.In addition,particle in cell simulations,employed to reveal the underlying physical mechanisms,show that the ionization and acceleration zone is pushed downwards towards the channel exit as the anode moves towards the exit.At the identical operating point,when the channel length is reduced from 32 to 27 mm,the ionization and acceleration zone moves towards the exit,and the parameters such as thrust and efficiency increase due to the high ionization rate,ion number density,and axial electric field.When the channel length is further moved to 24 mm,the parameters in terms of thrust(F) and efficiency(ηa) are reduced as a result of the decreasing ionization efficiency(ηm) and the larger plume divergence angle(α).In this paper,the results indicated that an optimum anode position(ΔL=27 mm) exists for the optimum performance.

Experimental Study on the Effects of Magnetic Field Configuration near the Channel Exit on the Plume Divergence of Hall Thrusters

Experimental investigations into the effects of the magnetic field configuration near the channel exit on the plume of Hall thrusters were conducted. The magnetic field configuration near the channel exit is characterized by the inclination angle between the magnetic field lines and the thruster radial direction. Different inclination angles were obtained by varying the current ratio in the coils. The plume divergence angles were measured by a dual-directed probe. The results showed that the plume divergence angle increased obviously with the increase in the magnitude of the inclination angle near the channel exit. Therefore, in order to optimize the magnetic field for reducing plume divergence, the magnitude of the inclination angle should be reduced as much as possible. It suggests that the magnetic field configuration near the channel exit is another important factor that affects plume divergence.

Influence of channel length on discharge performance of anode layer Hall thruster studied by particle-in-cell simulation

Hall thruster has the advantages of simple structure, high specific impulse, high efficiency, and long service life, and so on. It is suitable for spacecraft attitude control, North and South position keeping, and other track tasks. The anode layer Hall thruster is a kind of Hall thruster. The thruster has a longer anode area and a relatively short discharge channel. In this paper, the effect of the channel length on the performance of the anode layer Hall thruster is simulated by the PIC simulation method. The simulation results show that the change of the channel length has significant effect on the plasma parameters, such as potential and plasma density and so on. The ionization region mainly concentrates at the hollow anode outlet position, and can gradually move toward the channel outlet as the channel length decreases. The collision between the ions and the wall increases with the channel length increasing. So the proper shortening of the channel length can increase the life of the thruster. Besides, the results show that there is a best choice of the channel length for obtaining the best performance. In this paper, thruster has the best performance under a channel length of 5 mm.

The E×B drift instability in Hall thruster using 1D PIC/MCC simulation

The E×B drift instability is studied in Hall thruster using one-dimensional particle in cell(PIC)simulation method.By using the dispersion relation,it is found that unstable modes occur only in discrete bands in k space at cyclotron harmonics.The results indicate that the number of unstable modes increases by increasing the external electric field and decreases by increasing the radial magnetic field.The ion mass does not affect the instability wavelength.Furthermore,the results confirm that there is an instability with short wavelength and high frequency.Finally,it is shown that the electron and ion distribution functions deviate from the initial state and eventually the instability is saturated by ion trapping in the azimuthal direction.Also for light mass ion,the frequency and phase velocity are very high that could lead to high electron mobility in the axial direction.

Effect of Segmented Electrode Length on the Performances of an Aton-Type Hall Thruster

The influences of the low-emissive graphite segmented electrode t）laeed near the channel exit on the discharge characteristics of a Hall thruster are studied using the particle- in-cell method. A two-dimensional physical model is established according to the Hall thruster discharge channel configuration. The effects of electrode length on the potential, ion density, electron temperature, ionization rate and discharge current are investigated. It is found that, with tile increasing of the segmented electrode length, the equipotential lines bend towards the channel exit. and approximately parallel to the wall at the channel surface, the radial velocity and radial flow of ions are increased, and the electron temperature is also enhanced. Due to the conductive characteristic of electrodes, the radial electric field and the axial electron conductivity near the wall are enhanced, and the probability of the electron-atom ionization is reduced, which leads to the degradation of the ionization rate in the discharge channel. However, the interaction between electrons and the wall enhances the near wall conductivity, therefore the discharge current grows along with the segmented electrode length, and the performance of the thruster is also affected.

Low-frequency oscillations in Hall thrusters

In this paper, we summarize the research development of low-frequency oscillations in the last few decades. The findings of physical mechanism, characteristics and stabilizing methods of low-frequency oscillations are discussed. It shows that it is unreasonable and incomplete to model an ionization region separately to analyze the physical mechanism of low-frequency oscillations. Electro-dynamics as well as the formation conditions of ionization distribution play an important role in characteristics and stabilizing of low-frequency oscillations. Understanding the physical mechanism and characteristics of low- frequency oscillations thoroughly and developing a feasible method stabilizing this instability are still important research subjects.

Effect of the Hollow Cathode Heat Power on the Performance of an Hall-Effect Thruster

Effect of the hollow cathode heat power on the performance of a Hall-effect thruster is investigated. The variations in the Hall-effect thruster＇s performance （thrust, specific impulse and anode efficiency） with the hollow cathode heat power was obtained from the analysis of the experimental data. Through an analysis on the coupling relationship between the electrons emitted from the hollow cathode and the environmental plasma, it was found that the heat power would affect the electron emission of the emitter and the space potential of the coupling zone, which would lead to a change in the effective discharge voltage. The experimental data agree well with the results of calculation which can be used to explain the experimental phenomena.

Simulation study on the influence of magnetic field in the near-anode region on anode power deposition of ATON-type Hall thruster

The highest deposition of power and temperature is always near the cusp of the ATON-type Hall thruster.This shows that when there are electrons gathering at the cusp,the distribution of heat load will be uniform,which will potentially damage the reliability.Therefore,we optimize the magnetic field near the anode.We changed the magnetic field characteristics in the near-anode region with an additional magnetic screen,and performed numerical simulation with particle-incell simulation.The simulation results show that the magnetic field of the thruster with the additional magnetic screen can alleviate the over-concentration of power deposition on the anode and reduce the power deposition in the anode by 20%,while ensuring that the overall magnetic field characteristics do not change significantly.

Effect of Anode Magnetic Shield on Magnetic Field and Ion Beam in Cylindrical Hall Thruster

Numerical simulation of the effect of the anode magnetic shielding on the magnetic field and ion beam in a cylindrical Hall thruster is presented. The results show that after the anode is shielded by the magnetic shield, the magnetic field lines near the anode surface are obviously convex curved, the ratio of the magnetic mirror is enhanced, the width of the positive magnetic field gradient becomes larger than that without the anode magnetic shielding, the radial magnetic field component is enhanced, and the discharge plasma turbulence is reduced as a result of keeping the original saddle field profile and the important role the other two saddle field profiles play in restricting electrons. The results of the particle in cell （PIC） numerical simulation show that both the ion number and the energy of the ion beam increase after the anode is shielded by the magnetic shield. In other words, the specific impulse of the cylindrical Hall thruster is enhanced.

Effect of low-frequency oscillation on performance of Hall thrusters

In this paper, a direct connection between the discharge current amplitude and the thruster performance is established by varying solely the capacitance of the filter unit of the Hall thrusters. To be precise, the variation characteristics of ion current, propellant utilization efficiency, and divergence angle of plume at different low-frequency oscillation amplitudes are measured. The findings demonstrate that in the case of the propellant in the discharge channel just meets or falls below the full ionization condition, the increase of low-frequency oscillation amplitude can significantly enhance the ionization degree of the neutral gas in the channel and increase the thrust and anode efficiency of thruster. On the contrary, the increase in the amplitude of low-frequency oscillation will lead to increase the loss of plume divergence, therefore the thrust and anode efficiency of thruster decrease.

Experimental and numerical investigation of a Hall thruster with a chamfered channel wall

A discharge channel with a chamfered wall not only has application in the design of modern Hall thrusters, but also exists where the channel wall is eroded, and so is a common status for these units. In this paper, the laws and mechanisms that govern the effect of the chamfered wall on the performance of a Hall thruster are investigated. By applying both experimental measurement and particle-in-cell simulation, it is determined that there is a moderate chamfer angle that can further improve the optimal performance obtained with a straight channel. This is because the chamfering of the wall near the channel exit can enhance ion acceleration and effectively reduce ion recombination on the wall, which is favorable to the promotion of the thrust and efficiency. However, the chamfer angle should not be too large; otherwise, both the density of the propellant gas and the distribution of the plasma potential in the channel are influenced, which is undesirable for efficient propellant utilization and beam concentration. Therefore, it is suggested that the chamfer shape of the channel wall is an important factor that must be carefully considered in the design of Hall thrusters.

Effect of Magnetic Mirror on the Asymmetry of the Radial Profile of Near-Wall Conductivity in Hall Thrusters

Considering the actual magnetic field configuration in a Hall thruster, the effect of magnetic mirror on the radial profile of near-wall conductivity （NWC） is studied in this paper. The plasma electron dynamic process is described by the test particle method. The Monte Carlo scheme is used to solve this model. The radial profile of electron mobility is obtained and the role of magnetic mirror in NWC is analysed both theoretically and numerically. The numerical results show that the electron mobility peak due to NWC is inversely proportional to the magnetic mirror ratio and the asymmetry of electron mobility along the radial direction gets greater when the magnetic mirror is considered. This effect indicates that apart from the disparity in the magnetic field strength, the difference in the magnetic mirror ratio near the inner and outer walls would actually augment the asymmetry of the radial profile of NWC in Hall thrusters.

Particle-in-cell simulation for effect of anode temperature on discharge characteristics of a Hall effect thruster

Propellant gas flow has an important impact on the ionization and acceleration process of Hall effect thrusters （HETs）. In this paper, a particle-in-cell numerical method is used to study the effect of the anode temperature, i.e., the flow speed of the propellant gas, on the discharge characteristics of a HET. The simulation results show that, no matter the magnitude of the discharge voltage, the calculated variation trends of performance parameters with the anode temperature are in good agreement with the experimental ones presented in the literature. Further mechanism analysis indicates that the magnitude of the electron temperature is responsible for the two opposing variation laws found under different discharge voltages. When the discharge voltage is low, the electron temperature is low, and so is the intensity of the propellant ionization; the variation of the thruster performance with the anode temperature is thereby determined by the variation of the neutral density that affects the propellant utilization efficiency. When the discharge voltage is high, the electron temperature is large enough to guarantee a high degree of the propellant utilization no matter the magnitude of the anode temperature. The change of the thruster performance with the anode temperature is thus dominated by the change of the electron temperature and consequently the electron-neutral collisions as well as the electron cross-field mobility that affect the current utilization efficiency.