Photoionization Mass Spectrometric and Kinetic Modeling of Low-pressure Pyrolysis of Benzene

Pyrolysis of benzene at 30 Torr was studied from 1360 K to 1820 K in this work. Synchrotron vacuum ultraviolet photoionization mass spectrometry was employed to detect the pyroly- sis products such as radicals, isomers and polycyclic aromatic hydrocarbons, and measure their mole fraction profiles versus temperature. A low-pressure pyrolysis model of benzene was developed and validated by the experimental results. Rate of production analysis was performed to reveal the major reaction networks in both fuel decomposition and aromatic growth processes. It is concluded that benzene is mainly decomposed via H-abstraction reaction to produce phenyl and partly decomposed via unimolecular decomposition reac- tions to produce propargyl or phenyl. The decomposition process stops at the formation of acetylene and polyyne species like diacetylene and 1,3,5-hexatriyne due to their high thermal stabilities. Besides, the aromatic growth process in the low-pressure pyrolysis of benzene is concluded to initiate from benzene and phenyl, and is controlled by the even carbon growth mechanism due to the inhibited formation of C5 and C7 species which play important roles in the odd carbon growth mechanism.

Low-pressure pneumoperitoneum with abdominal wall lift in laparoscopic total mesorectal excision for rectal cancer:initial experience

AIM To evaluate the safety and feasibility of a new technology combining low-pressure pneumoperitoneum(LPP) and abdominal wall lift(AWL) in laparoscopic total mesorectal excision(TME) for rectal cancer.METHODS From November 2015 to July 2017,26 patients underwent laparoscopic TME for rectal cancer using LPP(6-8 mm Hg) with subcutaneous AWL in Qilu Hospital of Shandong University,Jinan,China.Clinical data regarding patients' demographics,intraoperative monitoring indices,operation-related indices andpathological outcomes were prospectively collected.RESULTS Laparoscopic TME was performed in 26 cases(14 anterior resection and 12 abdominoperineal resection) successfully,without conversion to open or laparoscopic surgery with standard-pressure pneumoperitoneum.Intraoperative monitoring showed stable heart rate,blood pressure and paw airway pressure.The mean operative time was 194.29 ± 41.27 min(range:125-270 min) and 200.41 ± 20.56 min(range:170-230 min) for anterior resection and abdominoperineal resection,respectively.The mean number of lymph nodes harvested was 16.71 ± 5.06(range:7-27).There was no positive circumferential or distal resection margin.No local recurrence was observed during a median follow-up period of 11.96 ± 5.55 mo(range:5-23 mo).CONCLUSION LPP combined with AWL is safe and feasible for laparoscopic TME.The technique can provide satisfactory exposure of the operative field and stable operative monitoring indices.

Process Optimization for AZ91 Mg-alloy Low-pressure EPC Process

The influence of a key process variable on the mold filling characteristics of AZ91 Mg-alloy was studied in the low pressure EPC process.The applied flow quantity of insert gas from 1 to 5 m~3/h associated with the pressurizing rate in the low pressure EPC casting process was considered for rectangle and L-shape plate casting. The experimental results show that there is an optimal flow quantity of insert gas for good mold filling characteristics in AZ91 Mg-alloy low-pressure EPC process. The optimal flow quantity of insert gas for the specimens is 3 to 4 m~3/h. Either less or higher than the optimal flow quantity of insert gas would lead to misrun defects or folds, blisters and porosity defects. The practice of hub casting confirmed that the low-pressure EPC process with an optimal processing variable exemplified as 4 m~3/h gas flow quantity was capable of producing complicated magnesium castings without misrun defects.

Numerical simulation and analysis of lithium plasma during low-pressure DC arc discharge

Alkali metal DC arc discharge has the characteristics of easy ionization,low power consumption,high plasma temperature and ionization degree,etc,which can be applied in aerospace vehicles in various ways.In this paper,we calculate the physical property parameters of lithium vapor,one of the major alkali metals,and analyze the discharge characteristics of lithium plasma with the magnetohydrodynamic(MHD)model.The discharge effects between constant current and voltage sources are also compared.It is shown that the lithium plasma of DC arc discharge has relatively high temperature and current density.The peak temperature can reach tens of thousands of K,and the current density reaches 6 x 107 A m 2.Under the same rated power,the plasma parameters of the constant voltage source discharge are much higher than those of the constant current source discharge,which can be used as the preferred discharge mode for aerospace applications.

An Experimental and Numerical Study on the Cleaning of Pleated Bag Filters Using Low-Pressure Pulsed-Jets

Pulsed-jet cleaning is recognized as the most efficient method to regenerate bag dust collectors traditionally used in industrial processes to control the emission of particulates.In this study,non-woven needle felt filter bags with and without a film coating material have been analyzed considering different geometries(different number N of pairs of pleated filter bag sides)in the frame of dedicated low-pressure pulsed-jet cleaning experiments.The flow structure inside the bag and the response characteristics of its wall have also been analyzed numerically through a computational fluid-dynamics/structural-dynamics(CFD-CSD)unidirectional fluid-solid coupling method.As shown by the experiments,the peak pressure(P_(0))on the wall of the filter bag with N=8 and 12 is higher,which indicates dust can be removed more effectively in these cases.The peak pressure on the wall increases first and then decreases along the direction of the bag length,while the peak pressure of the pleated filter bag with nonwoven needled felt film coating is greater than that without film coating.A comprehensive analysis of the time variation of acceleration,deformation,strain,stress and other factors,has led to the conclusion that the pleated filter bag with N=12 would be the optimal choice.

The mechanism study of low-pressure air plasma cleaning on large-aperture optical surface unraveled by experiment and reactive molecular dynamics simulation

Low-pressure air plasma cleaning is an effective method for removing organic contaminants on large-aperture optical components in situ in the inertial confinement fusion facility.Chemical reactions play a significant role in plasma cleaning,which is a complex process involving abundant bond cleavage and species generation.In this work,experiments and reactive molecular dynamics simulations were carried out to unravel the reaction mechanism between the benchmark organic contaminants of dibutyl phthalate and air plasma.The optical emission spectroscopy was used to study the overall evolution behaviors of excited molecular species and radical signals from air plasma as a reference to simulations.Detailed reaction pathways were revealed and characterized,and specific intermediate radicals and products were analyzed during experiments and simulation.The reactive species in the air plasma,such as O,HO_(2)and O_(3)radicals,played a crucial role in cleaving organic molecular structures.Together,our findings provide an atomic-level understanding of complex reaction processes of low-pressure air plasma cleaning mechanisms and are essential for its application in industrial plasma cleaning.

Effect of Low-pressure Carbonation on the Heat Inactivation and Cytoplasmic Acidification of Saccharomyces cerevisiae

Effect of low-pressure carbonation （LPC） on heat inactivation of Saccharomyces cerevisiae was investigated. The cell suspension was carbonated at 1 MPa and 4℃ for 15 min and subsequently heated from 51 to 61 ℃ and 5 s to 5 min （heating with LPC）. As a control experiment, cell suspension was heat-treated under atmospheric pressure without LPC （heating）. The inactivation ratio of heating at 53℃ and 55℃ for l rain with LPC was approximately 1 log order higher than heating alone. Extending heating time to 5 min did not widen the difference in the inactivation ratio between heating with LPC and heating alone at both heating temperatures. At 57℃, the difference in inactivation ratio increased from 1 to 2.5 log order with extending treatment time from 5 to 15 s. The results suggested that the enhanced inactivation effect by LPC was obtained at the higher temperature with short time treatment than the lower temperature with longer time treatment. Under fluorescence microscope observation of LPC-treated cell stained with LysoSensor probe, it seemed that LPC was hardly able to acidify the cytoplasm ofS. cerevisiae. It is considered that the ability orS. cerevisiae ceils to keep their cytoplasmic pH during LPC resulted in the inferior increase in heat inactivation ratio by LPC as compared with bacteria in the previous studies.

Neutrons in a nanosecond low-pressure discharge in deuterium

Stable neutron generation with a yield of ~1.2×10^(4) neutrons per pulse was obtained during d(d,n)^(3)He reaction initiated by the high-voltage nanosecond discharge in a gap with a potential tungsten cylinder(anode)and a grounded deuterated zirconium plate(cathode)filled with deuterium at a pressure of ~10^(2) Pa.Estimated duration of the neutron pulse was ~1.5 ns.Less intensive neutron emission was registered without deuterated plate.Splashing of material of the tungsten electrode was observed during the high-voltage nanosecond discharge in the deuterium,hydrogen,helium and argon at pressures of 10^(2)-10^(4) Pa.

A LOW-PRESSURE AND ONE-STEP METHOD FOR THE SYNTHESIS OF ALKYLIDYNETRICOBALT NONACARBONYL CLUSTERS:RCCo_8(CO)_9

Metal clusters RCCo_3(CO)_9(R-H,C1,Br,CH_3,Ph) were prepared in 18.8-57.3% yields from the reaction of cobalt(Ⅱ)salt and RCX_a under mild PTC conditions(latm CO,25℃).The cobalt salt was reduced to Co(CO)_4 in the presence of Na_3S_2O_4.

Simulation of propagation of the HPM in the low-pressure argon plasma

The propagation of the high-power microwave（HPM） with a frequency of 6 GHz in the lowpressure argon plasma was studied by the method of fluid approximation.The two-dimensional transmission model was built based on the wave equation,the electron drift-diffusion equations and the heavy species transport equations,which were solved by means of COMSOL Multiphysics software.The simulation results showed that the propagation characteristic of the HPM was closely related to the average electron density of the plasma.The attenuation of the transmitted wave increased nonlinearly with the electron density.Specifically,the growth of the attenuation slowed down as the electron density increased uniformly.In addition,the concrete transmission process of the HPM wave in the low-pressure argon plasma was given.

Microstructure and Properties of Low-pressure Cold Sprayed Al-based Composite Coatings on Magnesium Alloy Surface

Pure Al and Al-30%Al_(2)O_(3)composite coatings are prepared on the surface of AZ31B magnesium alloy by low-pressure cold spraying.The morphology and structure of the coatings are analyzed by scanning electron microscope (SEM),energy dispersive spectroscopy (EDS),and X-ray diffraction (XRD),and the effects of the addition of Al_(2)O_(3)on the microstructure of the Al-based coatings are discussed.The mechanical properties and corrosion resistance of the coatings are fully evaluated by the micro-hardness tester,electronic tensile machine,and electrochemical workstation.The results show that the coating structure is more uniform and denser,and the porosity is significantly reduced after the addition of Al_(2)O_(3).The interfaces between the coatings and the magnesium alloy substrate are distinct,and the coatings and the substrate are mechanically combined.Compared with the pure Al coating,the microhardness of the Al-Al_(2)O_(3)composite coating is increased to 61.1 HV_(0.2),and the bonding strength reaches above 53.1 MPa.The self-corrosion potential of the two coatings is higher than that of the magnesium alloy,and the self-corrosion current density is significantly lower than that of the magnesium alloy substrate.The Al-based coatings prepared by low-pressure cold spraying have high hardness,good bonding strength,and good corrosion resistance,which can be used for the repair and protection of magnesium alloy structural parts.

Experimental Study on Ammonia Co-Firing with Coal for Carbon Reduction in the Boiler of a 300-MW Coal-Fired Power Station

To reduce CO_(2) emissions from coal-fired power plants,the development of low-carbon or carbon-free fuel combustion technologies has become urgent.As a new zero-carbon fuel,ammonia(NH_(3))can be used to address the storage and transportation issues of hydrogen energy.Since it is not feasible to completely replace coal with ammonia in the short term,the development of ammonia-coal co-combustion technology at the current stage is a fast and feasible approach to reduce CO_(2) emissions from coal-fired power plants.This study focuses on modifying the boiler and installing two layers of eight pure-ammonia burners in a 300-MW coal-fired power plant to achieve ammonia-coal co-combustion at proportions ranging from 20%to 10%(by heat ratio)at loads of 180-to 300-MW,respectively.The results show that,during ammonia-coal co-combustion in a 300-MW coal-fired power plant,there was a more significant change in NO_(x) emissions at the furnace outlet compared with that under pure-coal combustion as the boiler oxygen levels varied.Moreover,ammonia burners located in the middle part of the main combustion zone exhibited a better high-temperature reduction performance than those located in the upper part of the main combustion zone.Under all ammonia co-combustion conditions,the NH_(3) concentration at the furnace outlet remained below 1 parts per million(ppm).Compared with that under pure-coal conditions,the thermal efficiency of the boiler slightly decreased(by 0.12%-0.38%)under different loads when ammonia co-combustion reached 15 t·h^(-1).Ammonia co-combustion in coal-fired power plants is a potentially feasible technology route for carbon reduction.

Numerical Simulation of Combustion in 660MWTangentially Fired Pulverized Coal Boiler on Ultra-Low Load Operation

In this paper,the combustion conditions in the boiler furnace of a 660 MWtangential fired pulverized coal boiler are numerically simulated at 15%and 20%rated loads,to study the flexibility of coal-fired power units on ultra-low load operation.The numerical results show that the boiler can operate safely at 15%and 20%ultra-low loads,and the combustion condition in the furnace is better at 20%load,and the tangent circles formed by each characteristic section in the furnace are better,and when the boiler load is decreased to 15%,the tangent circles in the furnace begin to deteriorate.The average flue gas temperature of different areas of the furnace shows that when the boiler furnace operates under ultra-low load conditions,the average smoke temperature of the cold ash hopper at 20%load is basically the same as the average smoke temperature at 15%load;in the burner area,the average smoke temperature of the cold ash hopper at 20%load is about 50 K higher than that at 15%load;in the burned out area,the average smoke temperature of the cold ash hopper at 20%load is slightly higher than that at 15%load.The average temperature of flue gas in the furnace showed a tendency to increase rapidly with the height of the furnace,then slow down and fluctuate the temperature in the burner area,and finally increase slightly in the burnout area due to the further combustion of combustible components to release heat,and then began to decrease.

Optimizing Two-Phase Flow Heat Transfer:DCS Hybrid Modeling and Automation in Coal-Fired Power Plant Boilers

In response to escalating challenges in energy conservation and emission reduction,this study delves into the complexities of heat transfer in two-phase flows and adjustments to combustion processes within coal-fired boilers.Utilizing a fusion of hybrid modeling and automation technologies,we develop soft measurement models for key combustion parameters,such as the net calorific value of coal,flue gas oxygen content,and fly ash carbon content,within theDistributedControl System(DCS).Validated with performance test data,thesemodels exhibit controlled root mean square error(RMSE)and maximum absolute error(MAXE)values,both within the range of 0.203.Integrated into their respective automatic control systems,thesemodels optimize two-phase flow heat transfer,finetune combustion conditions,and mitigate incomplete combustion.Furthermore,this paper conducts an in-depth exploration of the generationmechanismof nitrogen oxides(NOx)and low oxygen emission reduction technology in coal-fired boilers,demonstrating a substantial reduction in furnace exit NOx generation by 30%to 40%and the power supply coal consumption decreased by 1.62 g/(kW h).The research outcomes highlight the model’s rapid responsiveness,enabling prompt reflection of transient variations in various economic indicator parameters.This provides a more effective means for real-time monitoring of crucial variables in coal-fired boilers and facilitates timely combustion adjustments,underscoring notable achievements in boiler combustion.The research not only provides valuable and practical insights into the intricacies of two-phase flow heat transfer and heat exchange but also establishes a pioneering methodology for tackling industry challenges.

Numerical Calculations and Cold Tests for Flow Fields of a 220t/h Retrofitted Oil-Boiler

In this paper, cold simulation experiments and numerical calculations are conducted to predict 3 D flow field aerodynamics for an oil furnace after being retrofitted due to its fuel variation. K ε model and SIMPLE program under body fit coordination (BFC) system, in which TTM non orthogonal method is used to control the irregular geometric boundary, are adopted to solve the control equations. Model tests are conducted to check the calculation results, showing that they are in agreement with each other. Three different alternatives with different side window locations are also calculated to optimize the designs. The field retrofitting results show that the combination of cold tests with numerical calculations has prosperous application in retrofitting or renewing medium and small boilers.

Three-Dimensional Dynamic Modeling of a Tangentially Fired Utility Boiler Furnace

The tangentially fired utility boiler furnace is divided into several sections. The dynamic mathematical models for each section are presented. In the combustion zone, three dimensional model is used, while for the upper sections, lumped parameter model is used instead. With the combination of different models, we can get detailed distributions of gas velocity, temperature, chemical species, heat flux, etc. in the furnace, but with less CPU time. The radiation through the interfaces of each section is cons...

Modeling and Simulation Study on Reverse Swirl of Secondary Air in Large Tangentially Fired Boiler

Based on the porosity method and the improved non uniform QUICK scheme, this paper describes a three dimensional computer simulation to predict the flow characteristics in a tangentially fired boiler. The model is applied to a 600?MW boiler modeling under different operating conditions of reverse swirl of secondary air. The numerical results achieve reasonable agreement with experimental data. The calculated results of flow field, the pressure distribution, the relative diameter of tangential circle, angular momentum flux in furnace and the velocity distribution index in horizontal gas pass are analyzed in detail. And then the effects of the reverse swirl of secondary air on flue gas imbalance are discussed. Finally a reasonable operating condition of the reverse swirl of secondary air is presented.

Neural network approach to predicting mercury emission from utility boiler

The feasibility of using an ANN method to predict the mercury emission and speciation in the flue gas of a power station under un-tested combustion/operational conditions is evaluated. Based on existing field testing datasets for the emissions of three utility boilers, a 3-layer back-propagation network is applied to predict the mercury speciation at the stack. The whole prediction procedure includes： collection of data, structuring an artificial neural network （ANN） model, training process and error evaluation. A total of 59 parameters of coal and ash analyses and power plant operating conditions are treated as input variables, and the actual mercury emissions and their speciation data are used to supervise the training process and verify the performance of prediction modeling. The precision of model prediction （ root- mean-square error is 0. 8 μg/Nm3 for elemental mercury and 0. 9 μg/Nm3 for total mercury） is acceptable since the spikes of semi- mercury continuous emission monitor （SCEM） with wet conversion modules are taken into consideration.

Analysis of Prese nt Operating Situati on of Large Size Coal-F ired Utility Boilers

Large size utility boilers develop rapidly in China, both their reliability and economics have reached better level. The operating situations of various existing boilers on the basis of different coals are analyzed, it is held that, the notable energy imbalance of furnace exit, ever existing in the tangential firing boilers has been solved, with comparatively lower NOX emission concentration of gained. The higher NOX emission concentration and furnace slagging etc. problems existing in wall firing boilers are notable. The comprehensive analysis shows that, it is appropriate to choose lower furnace volume heat release rate and higher flame height in the type selection design of boilers, and sufficient margin should be kept in the selection of coal pulverizing mills.

Characteristics of Phosphorus Adsorption with Boiler Slag and Process Optimization

[Objective] This study aimed to investigate the characteristics of phosphorus adsorption on boiler slag and optimize the adsorption process. [Method] Boiler slag was used as an adsorbent in the single-grade adsorption process to dispose the rural domestic sewage. During the course, phosphorus adsorption kinetics and thermodynamics, adsorption operating curve and the minimum boiler slag dosage were analyzed and calculated. [Result] Langmuir adsorption isotherm could be applied to describe the absorption of phosphorus with boiler slag, and the absorption kinetics was confirmed with the pseudo second-order equation. The maximum absorption quantity and the initial absorption rate increased with the rise of temperature, reaching up to 0.159 1 mg/g and 0.169 8 mg/(g·min) respectively at 40 ℃. Thermodynamic variables ΔG0<0 and ΔH0>0 indicated that the entire process was a spontaneous endothermic reaction, and high temperature would facilitate the reaction of absorption. In the single grade adsorption, the minimum adsorbent dosage decreased as the temperature rose; at 40 ℃ the optimum mass ratio of boiler slag to wastewater was 3.31 kg/m3. [Conclusion] The adsorption process with boiler slag as adsorbent is an economical and effective approach for treating rural domestic sewage.