Low-Temperature Sintering and Microwave DielectricProperties of Ba_2Ti_3Nb_4O_(18) Ceramics

The effects of CuO and H3BO3 additions on the low-temperature sintering,microstructure,and microwave dielectric properties of Ba2Ti3Nb4O18 ceramics were investigated.The addition of less amount of CuO （ 〈1 wt%） considerably facilitated the densification of Ba2Ti3Nb4O18 ceramics.Appropriate addition of H3BO3 （ 〈3.5 wt%） remarkably improved the microwave dielectric properties of ceramics.The addition of H3BO3 and CuO successfully reduced the sintering temperature of Ba2Ti3Nb4O18 ceramics from 1300 to 1050 ℃.Ba2Ti3Nb4O18 ceramics sintered at 1 050 ℃ for 4 h with the addition of 1.0 wt% CuO and 3.5 wt% H3BO3 exhibited good microwave dielectric properties：er=33.74,Q？f=13 812 GHz,and tf=-5.35 ppm/°C at about 5.0 GHz.

UHV/CVD Low-Temperature Si Epitaxy Used for SiGe HBT

Low-temperature-epitaxy n-type silicon layers were grown on arsenic-doped n+-type silicon substrate by using ultra-high vacuum chemical vapor deposition (UHV/CVD). The transition region thickness of the Si layers grown under different PH3 flux and different growth temperature were investigated by spreading resistance probe. Results showed that the growth temperature had remarkable influence on the arsenic diffusion from the Si substrate. The thicknesses of the transition region were 0.16 μm grown at 700 ℃ and 0.06 μm grown at 500 ℃, respectively. Moreover, the dopant profiles were very abrupt. X-ray diffraction investigation of the epitaxial Si layer showed the quality of Si layer was very high.SiG e HBT device was fabricated by using a revised double-mesa polysilicon-emitter process. Tests show that the CB-junction breakdown characteristic of the SiGe HBT is very hard, and the leakage current is only 0.3 μA under a reverse voltage of - 14.0 V. The SiGe HBT device had also good output performance, and the current gain is 60.

Boosting oxygen reduction activity and CO_(2) resistance on bismuth ferrite-based perovskite cathode for low-temperature solid oxide fuel cells below 600℃

Developing efficient and stable cathodes for low-temperature solid oxide fuel cells(LT-SOFCs) is of great importance for the practical commercialization.Herein,we propose a series of Sm-modified Bi_(0.7-x)Sm_xSr_(0.3)FeO_(3-δ) perovskites as highly-active catalysts for LT-SOFCs.Sm doping can significantly enhance the electrocata lytic activity and chemical stability of cathode.At 600℃,Bi_(0.675)Sm_(0.025)Sr_(0.3)FeO_(3-δ)(BSSF25) cathode has been found to be the optimum composition with a polarization resistance of 0.098 Ω cm^2,which is only around 22.8% of Bi_(0.7)Sr_(0.3)FeO_(3-δ)(BSF).A full cell utilizing BSSF25 displays an exceptional output density of 790 mW cm^(-2),which can operate continuously over100 h without obvious degradation.The remarkable electrochemical performance observed can be attributed to the improved O_(2) transport kinetics,superior surface oxygen adsorption capacity,as well as O_(2)p band centers in close proximity to the Fermi level.Moreover,larger average bonding energy(ABE) and the presence of highly acidic Bi,Sm,and Fe ions restrict the adsorption of CO_(2) on the cathode surface,resulting in excellent CO_(2) resistivity.This work provides valuable guidance for systematic design of efficient and durable catalysts for LT-SOFCs.

Temperature inversion enables superior stability for low-temperature Zn-ion batteries

It is challenging for aqueous Zn-ion batteries(ZIBs)to achieve comparable low-temperature(low-T)performance due to the easy-frozen electrolyte and severe Zn dendrites.Herein,an aqueous electrolyte with a low freezing point and high ionic conductivity is proposed.Combined with molecular dynamics simulation and multi-scale interface analysis(time of flight secondary ion mass spectrometry threedimensional mapping and in-situ electrochemical impedance spectroscopy method),the temperature independence of the V_(2)O_(5)cathode and Zn anode is observed to be opposite.Surprisingly,dominated by the solvent structure of the designed electrolyte at low temperatures,vanadium dissolution/shuttle is significantly inhibited,and the zinc dendrites caused by this electrochemical crosstalk are greatly relieved,thus showing an abnormal temperature inversion effect.Through the disclosure and improvement of the above phenomena,the designed Zn||V_(2)O_(5)full cell delivers superior low-T performance,maintaining almost 99%capacity retention after 9500 cycles(working more than 2500 h)at-20°C.This work proposes a kind of electrolyte suitable for low-T ZIBs and reveals the inverse temperature dependence of the Zn anode,which might offer a novel perspective for the investigation of low-T aqueous battery systems.

Enhancing performance of low-temperature processed CsPbI2Br all-inorganic perovskite solar cells using polyethylene oxide-modified TiO_(2)

CsPbX_(3)-based(X=I,Br,Cl)inorganic perovskite solar cells(PSCs)prepared by low-temperature process have attracted much attention because of their low cost and excellent thermal stability.However,the high trap state density and serious charge recombination between low-temperature processed TiO_(2)film and inorganic perovskite layer interface seriously restrict the performance of all-inorganic PSCs.Here a thin polyethylene oxide(PEO)layer is employed to modify TiO_(2)film to passivate traps and promote carrier collection.The impacts of PEO layer on microstructure and photoelectric characteristics of TiO_(2)film and related devices are systematically studied.Characterization results suggest that PEO modification can reduce the surface roughness of TiO_(2)film,decrease its average surface potential,and passivate trap states.At optimal conditions,the champion efficiency of CsPbI_(2)Br PSCs with PEO-modified TiO_(2)(PEO-PSCs)has been improved to 11.24%from 9.03%of reference PSCs.Moreover,the hysteresis behavior and charge recombination have been suppressed in PEO-PSCs.

Structure,far-infrared spectroscopy,microwave dielectric properties,and improved low-temperature sintering characteristics of tri-rutile Mg_(0.5)Ti_(0.5)TaO_(4) ceramics

In this study,tri-rutile type Mg_(0.5)Ti_(0.5)TaO_(4) ceramics were synthesized,where the structure–property relationship,especially the structural configuration and intrinsic dielectric origin of Mg_(0.5)Ti_(0.5)TaO_(4) ceramics,and the low-firing characteristics were studied.It is found that the tri-rutile structural type is unambiguously identified through the Rietveld refinement analysis,the selected area electron diffraction(SAED),and the high-resolution transmission electron microscopy(HRTEM)along the[110]zone axis.With the increase in sintering temperature,the densification and uniformity of crystal growth play important roles in regulating the microwave dielectric properties of Mg_(0.5)Ti_(0.5)TaO_(4) ceramics.Intrinsically,theoretical dielectric properties calculated by the far-infrared reflective spectra approached the experimental values,indicating the importance of structural features to dielectric properties.Furthermore,a glass additive with high matching relevance with ceramics has been developed to decrease the high sintering temperature of Mg_(0.5)Ti_(0.5)TaO_(4) ceramics,where 2–4 wt%Li_(2)O–MgO–ZnO–B_(2)O_(3)–SiO_(2)(LMZBS)glass frit was adopted to reduce the suitable temperature from 1275 to 1050℃ without significantly deteriorating the microwave dielectric characteristics.Specifically,Mg_(0.5)Ti_(0.5)TaO_(4) ceramics containing 2 wt% glass addition sintered at 1050℃for 4 h possess excellent microwave dielectric properties:dielectric constant(ε_(r))=44.3,quality factor multiplied by resonant frequency(Q×f)=23,820 GHz(f=6.2 GHz),and the temperature coefficient of resonant frequency(τ_(f))=123.2 ppm/℃.

Global optimization of process parameters for low-temperature SiN_(x) based on orthogonal experiments

Low-temperature silicon nitride(SiNx)films deposited by plasma-enhanced chemical vapor deposition(PECVD)have huge application potential in the flexible display.However,the applicability of SiNx largely depends on the film’s general properties,including flexibility,deposition rate,residual stress,elastic modulus,fracture strain,dielectric constant,refraction index,etc.Process optimization towards specific application by conventional experiment design needs lots of work due to the interaction of muti quality and process parameters.Therefore,an efficient global optimization approach for the process technology was proposed based on the Taguchi orthogonal experiment method considering muti-factor muti-responses.First of all,the Taguchi orthogonal experiment design and analysis was used to rank the influences of main process parameters on the quality characteristics,including radio frequency(RF)power,pressure,silane flow rate,ammonia flow rate and nitrogen flow rate.Then,the global optimization approach was carried out utilizing the multi-response optimizer considering the combination target of film formation rate,residual stress,dielectric constant,elastic modulus,fracture strain,refractive index.Finally,the optimal solution of the SiNx film was finally obtained and verified.

Low-temperature characteristicsof rubbers and performance testsof type 120 emergencyvalve diaphragms

Purpose–The type 120 emergency valve is an essential braking component of railway freight trains,butcorresponding diaphragms consisting of natural rubber(NR)and chloroprene rubber(CR)exhibit insufficientaging resistance and low-temperature resistance,respectively.In order to develop type 120 emergency valverubber diaphragms with long-life and high-performance,low-temperatureresistant CR and NR were processed.Design/methodology/approach–The physical properties of the low-temperature-resistant CR and NRwere tested by low-temperature stretching,dynamic mechanical analysis,differential scanning calorimetryand thermogravimetric analysis.Single-valve and single-vehicle tests of type 120 emergency valves werecarried out for emergency diaphragms consisting of NR and CR.Findings–The low-temperature-resistant CR and NR exhibited excellent physical properties.The elasticityand low-temperature resistance of NR were superior to those of CR,whereas the mechanical properties of thetwo rubbers were similar in the temperature range of 0℃–150℃.The NR and CR emergency diaphragms metthe requirements of the single-valve test.In the low-temperature single-vehicle test,only the low-temperaturesensitivity test of the NR emergency diaphragm met the requirements.Originality/value–The innovation of this study is that it provides valuable data and experience for futuredevelopment of type 120 valve rubber diaphragms.

Structural Engineering of Anode Materials for Low-Temperature Lithium-Ion Batteries:Mechanisms,Strategies,and Prospects

The severe degradation of electrochemical performance for lithium-ion batteries(LIBs)at low temperatures poses a significant challenge to their practical applications.Consequently,extensive efforts have been contributed to explore novel anode materials with high electronic conductivity and rapid Li^(+)diffusion kinetics for achieving favorable low-temperature performance of LIBs.Herein,we try to review the recent reports on the synthesis and characterizations of low-temperature anode materials.First,we summarize the underlying mechanisms responsible for the performance degradation of anode materials at subzero temperatures.Second,detailed discussions concerning the key pathways(boosting electronic conductivity,enhancing Li^(+)diffusion kinetics,and inhibiting lithium dendrite)for improving the low-temperature performance of anode materials are presented.Third,several commonly used low-temperature anode materials are briefly introduced.Fourth,recent progress in the engineering of these low-temperature anode materials is summarized in terms of structural design,morphology control,surface&interface modifications,and multiphase materials.Finally,the challenges that remain to be solved in the field of low-temperature anode materials are discussed.This review was organized to offer valuable insights and guidance for next-generation LIBs with excellent low-temperature electrochemical performance.

Advances in sodium-ion batteries at low-temperature: Challenges and strategies

With the continuing boost in the demand for energy storage,there is an increasing requirement for batteries to be capable of operation in extreme environmental conditions.Sodium-ion batteries(SIBs) have emerged as a highly promising energy storage solution due to their promising performance over a wide range of temperatures and the abundance of sodium resources in the earth's crust.Compared to lithiumion batteries(LIBs),although sodium ions possess a larger ionic radius,they are more easily desolvated than lithium ions.Fu rthermore,SIBs have a smaller Stokes radius than lithium ions,resulting in improved sodium-ion mobility in the electrolyte.Nevertheless,SIBs demonstrate a significant decrease in performance at low temperatures(LT),which constrains their operation in harsh weather conditions.Despite the increasing interest in SIBs,there is a notable scarcity of research focusing specifically on their mechanism under LT conditions.This review explores recent research that considers the thermal tolerance of SIBs from an inner chemistry process perspective,spanning a wide temperature spectrum(-70 to100℃),particularly at LT conditions.In addition,the enhancement of electrochemical performance in LT SIBs is based on improvements in reaction kinetics and cycling stability achieved through the utilization of effective electrode materials and electrolyte components.Furthermore,the safety concerns associated with SIBs are addressed and effective strategies are proposed for mitigating these issues.Finally,prospects conducted to extend the environmental frontiers of commercial SIBs are discussed mainly from three viewpoints including innovations in materials,development and research of relevant theoretical mechanisms,and intelligent safety management system establishment for larger-scale energy storage SIBs.

Low-temperatures synthesis of CuS nanospheres as cathode material for magnesium second batteries

Rechargeable magnesium batteries(RMBs),as one of the most promising candidates for efficient energy storage devices with high energy,power density and high safety,have attracted increasing attention.However,searching for suitable cathode materials with fast diffusion kinetics and exploring their magnesium storage mechanisms remains a great challenge.Cu S submicron spheres,made by a facile low-temperature synthesis strategy,were applied as the high-performance cathode for RMBs in this work,which can deliver a high specific capacity of 396mAh g^(-1)at 20 mA g^(-1) and a remarkable rate capacity of 250 m Ah g^(-1)at 1000 mA g^(-1).The excellent rate performance can be assigned to the nano needle-like particles on the surface of Cu S submicron spheres,which can facilitate the diffusion kinetics of Mg^(2+).Further storage mechanism investigations illustrate that the Cu S cathodes experience a two-step conversion reaction controlled by diffusion during the electrochemical reaction process.This work could make a contribution to the study of the enhancement of diffusion kinetics of Mg2+and the reaction mechanism of RMBs.

Ca and Sr co-doping induced oxygen vacancies in 3DOM La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)catalysts for boosting low-temperature oxidative coupling of methane

It is urgent to develop catalysts with application potential for oxidative coupling of methane(OCM)at relatively lower temperature.Herein,three-dimensional ordered macro porous(3 DOM)La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)(A_(2)B_(2)O_(7)-type)catalysts with disordered defective cubic fluorite phased structure were successfully prepared by a colloidal crystal template method.3DOM structure promotes the accessibility of the gaseous reactants(O2and CH4)to the active sites.The co-doping of Ca and Sr ions in La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)catalysts improved the formation of oxygen vacancies,thereby leading to increased density of surface-active oxygen species(O_(2)^(-))for the activation of CH4and the formation of C2products(C2H6and C2H4).3DOM La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)catalysts exhibit high catalytic activity for OCM at low temperature.3DOM La1.7Sr0.3Ce1.7Ca0.3O7-δcatalyst with the highest density of O_(2)^(-)species exhibited the highest catalytic activity for low-temperature OCM,i.e.,its CH4conversion,selectivity and yield of C2products at 650℃are 32.2%,66.1%and 21.3%,respectively.The mechanism was proposed that the increase in surface oxygen vacancies induced by the co-doping of Ca and Sr ions boosts the key step of C-H bond breaking and C-C bond coupling in catalyzing low-temperature OCM.It is meaningful for the development of the low-temperature and high-efficient catalysts for OCM reaction in practical application.

Fluidized magnetization roasting of refractory siderite-containing iron ore via preoxidation-low-temperature reduction

Magnetization roasting is one of the most effective way of utilizing low-grade refractory iron ore.However,the reduction roasting of siderite(FeCO3)generates weakly magnetic wüstite,thus reducing iron recovery via weak magnetic separation.We systematically studied and proposed the fluidized preoxidation-low-temperature reduction magnetization roasting process for siderite.We found that the maghemite generated during the air oxidation roasting of siderite would be further reduced into wüstite at 500 and 550℃due to the unstable intermediate product magnetite(Fe_(3)O_(4)).Stable magnetite can be obtained through maghemite reduction only at low temperature.The optimal fluidized magnetization roasting parameters included preoxidation at 610℃for 2.5 min,followed by reduction at 450℃for 5 min.For roasted ore,weak magnetic separation yielded an iron ore concentrate grade of 62.0wt%and an iron recovery rate of 88.36%.Compared with that of conventional direct reduction magnetization roasting,the iron recovery rate of weak magnetic separation had greatly improved by 34.33%.The proposed fluidized preoxidation-low-temperature reduction magnetization roasting process can realize the efficient magnetization roasting utilization of low-grade refractory siderite-containing iron ore without wüstite generation and is unlimited by the proportion of siderite and hematite in iron ore.

Low-temperature photothermal-induced alkyl radical release facilitates dihydroartemisinin-triggered“valve-off”starvation therapy

The high nutrient and energy demand of tumor cells compared to normal cells to sustain rapid proliferation offer a potentially auspicious avenue for implementing starvation therapy.However,conventional starvation therapy,such as glucose exhaustion and vascular thrombosis,can lead to systemic toxicity and exacerbate tumor hypoxia.Herein,we developed a new“valve-off”starvation tactic,which was accomplished by closing the valve of glucose transporter protein 1(GLUT1).Specifically,dihydroartemisinin(DHA),2,20-azobis[2-(2-imidazolin-2-yl)propane]dihydrochloride(AI),and Ink were co-encapsulated in a sodium alginate(ALG)hydrogel.Upon irradiation with the 1064 nm laser,AI rapidly disintegrated into alkyl radicals(R·),which exacerbated the DHA-induced mitochondrial damage through the generation of reactive oxygen species and further reduced the synthesis of adenosine triphosphate(ATP).Simultaneously,the production of R·facilitated DHA-induced starvation therapy by suppressing GLUT1,which in turn reduced glucose uptake.Systematic in vivo and in vitro results suggested that this radical-enhanced“valveoff”strategy for inducing tumor cell starvation was effective in reducing glucose uptake and ATP levels.This integrated strategy induces tumor starvation with efficient tumor suppression,creating a new avenue for controlled,precise,and concerted tumor therapy.

Molecular composition of low-temperature oxidation products of the heavy oil

Low-temperature oxidation(LTO)is the main reaction that affects fuel formation in the in-situ combustion process,which has important significance for the subsequent combustion propulsion and the successful extraction of crude oil.In this study,heavy oil was subjected to LTO reactions at different temperatures.Three types of reaction products with varying oxidation depths were characterized in terms of the number of oxygen atoms and the polarity of the molecule to reveal the low-temperature oxidation process of the heavy oil.Ketone compounds and acid polyoxides in the oil phase and deep oxidation products with a higher number of oxygen atoms in the coke were identified with increasing oxidation depth.The experimental results showed that the oxidation reaction of the heavy oil changed from kinetic-controlled to diffusion-controlled in the open oxidation system of the heavy oil as the oxidation depth increased.The oxidation reaction of the oil phase reached a maximum and stable value in oxygen content.The molecular compositions of the ketone compound and acid polyoxide did not change significantly with further increase in reaction temperature.The molecular compositions of the deep oxidation products with a higher number of oxygen atoms in the coke phase changed significantly.The coke precursor molecules with a lower oxygen content and condensation degree participated in the coke formation,and the oxidation reaction pathway and the complexity of the oxidation product component also increased.

Effects of Potassium Ferrate and Low-Temperature Thermal Hydrolysis Co-Pretreatment on the Hydrolysis and Anaerobic Digestion Process of Waste Activated Sludge

This study evaluated the effect of potassium ferrate(PF)and low-temperature thermal hydrolysis co-pretreatment on the promotion of sludge hydrolysis process and the impact on acid production in the subsequent anaerobic digestion process.The analytical investigations showed that co-pretreatment significantly facilitated the hydrolysis process of the sludge and contributed to the accumulation of short-chain fatty acids(SCFAs).The pretreatment conditions under the optimal leaching of organic matter from sludge were hydrothermal temperature of 75℃,hydrothermal treatment time of 12 h,and PF dosage of 0.25 g g^(−1)TSS(total suspended solids),according to the results of orthogonal experiments.By pretreatment under proper conditions,the removal rate of soluble chemical oxygen demand(SCOD)achieved 71.8%at the end of fermentation and the removal rate of total phosphorus(TP)was 69.1%.The maximum yield of SCFAs was 750.3 mg L^(−1),7.45 times greater than that of the blank group.Based on the analysis of the anaerobic digestion mechanism,it was indicated that the co-pretreatment could destroy the floc structure on the sludge surface and improve organic matter dissolving,resulting in more soluble organic substances for the acidification process.Furthermore,microbial community research revealed that the main cause of enhanced SCFAs generation was an increase in acidogenic bacteria and a reduction of methanogenic bacteria.

Low-Temperature Synthesis of Nano-AlN Based on Solid Nitrogen Source by Plasma-Assisted Ball Milling

Plasma-assisted ball milling was carried out on the Al+C3H6N6 system and Al+C_(4)H_(4)N_(4) system,respectively.The phase structure,functional groups and synthesis mechanism were analyzed by XRD and FT-IR,and the differences in the synthesis process of nano-AlN with different solid nitrogen sources were discussed.The results show that C3H6N6 has a stable triazine ring structure,and its chemical bond is firm and difficult to break,so AlN cannot be synthesized directly by solid-solid reaction at room temperature.However,there are a large number of nitrile groups(-CN)and amino groups(-NH_(2))in C_(4)H_(4)N_(4) molecules.Under the combined action of plasma bombardment and mechanical energy activation,C_(4)H_(4)N_(4) molecules undergo polycondensation and deamination,so that the ball milling tank is filled with a large number of active nitrogen-containing groups such as N=,≡N,etc.These groups and ball milling activated Al can synthesize nano-AlN at room temperature,with a conversion rate of 92%.SEM,DSC/TG analysis showed that the powder obtained by ball milling was formed by soft agglomeration of many fine primary particles about 50–80 nm.The surface morphology of the powder was loose and porous,and it had strong activity.After annealing at 800℃,the conversion rate of the Al+C_(4)H_(4)N_(4) system reached 99%.

Simultaneously removal of P and B from Si by Sr and Zr co-addition during Al–Si low-temperature solvent refining

To remove the key impurity elements,P and B,from primary Si simultaneously,Sr and Zr co-addition to Al-Si alloy systems during solvent refining has been investigated.Sr reacts with Al,Si,and P in the melt to form a P-containing Al_(2)Si_(2)Sr phase and Zr reacts with B to form a ZrB_(2) phase.In the Al-Si-Sr-Zr system,high removal fractions of P and B in the primary Si,with 84.8%-98.4%and 90.7%-96.7%,respectively,are achieved at the same time,respectively.The best removal effect is obtained in the sample with the addition of Sr-32000+Zr-3000μg·kg^(-1),and the removal fractions of P and B in the purified Si reach 98.4%and 96.1%.Compared with the Sr/Zr single-addition,the removal effects of Sr and Zr co-addition on P and B do not show a significant downward trend,indicating that the nucleation and growth of the B/P-containing impurity phases are mutually independent.Finally,an evolution model is proposed to describe the nucleation and the growth stages of Sr/Zr-containing compound phases,which reveals the interaction between the impurity phases and the primary Si.

The Application of Thermomechanical Dynamics (TMD) to the Analysis of Nonequilibrium Irreversible Motion and a Low-Temperature Stirling Engine

We applied the method of Thermomechanical Dynamics (TMD) to a low-temperature Stirling engine, and the dissipative equation of motion and time-evolving physical quantities are self-consistently calculated for the first time in this field. The thermomechanical states of the heat engine are in Nonequilibrium Irreversible States (NISs), and time-dependent thermodynamic work W(t), internal energy E(t), energy dissipation or entropy Qd(t), and temperature T(t), are precisely studied and computed in TMD. We also introduced the new formalism, Q(t)-picture of thermodynamic heat-energy flows, for consistent analyses of NISs. Thermal flows in a long-time uniform heat flow and in a short-time heat flow are numerically studied as examples. In addition to the analysis of time-dependent physical quantities, the TMD analysis suggests that the concept of force and acceleration in Newtonian mechanics should be modified. The acceleration is defined as a continuously differentiable function of Class C2 in Newtonian mechanics, but the thermomechanical dynamics demands piecewise continuity for acceleration and thermal force, required from physical reasons caused by frictional variations and thermal fluctuations. The acceleration has no direct physical meaning associated with force in TMD. The physical implications are fundamental for the concept of the macroscopic phenomena in NISs composed of systems in thermal and mechanical motion.

Formation mechanisms of Ti_(3)(Si,Al)C_(2)/Al_(2)O_(3) composites from Ti_(3)AlC_(2) and SiO via low-temperature sintering

Ti_(3)SiC_(2)/Al_(2)O_(3) composites have attracted attention due to their excellent mechanical and electromagnetic properties,but the high temperatures(≥1400℃)required for the densification of aluminum oxide(Al_(2)O_(3))leads to the decomposition of Ti_(3)SiC_(2).To address this issue,Ti_(3)(Si_(x)Al_(1−x))C2/Al_(2)O_(3)(x represents the Si content)composites were synthesized for the first time via hot-pressing(HP)sintering and current-assisted sintering(CAS)of mixed Ti_(3)AlC_(2) and silicon monoxide(SiO)powders at 1300 and 1200℃,respectively.Both approaches produced composites with x values greater than 0.9,indicating that the compositions of the prepared composites were similar to those of Ti_(3)SiC_(2)/Al_(2)O_(3) composites.The synthetic mechanism involved substitution and continuous interdiffusion of Al and Si atoms.The composite prepared by CAS at 1200℃ was compacted,whereas the composite prepared by HP had a low density.The low-temperature densification mechanism is attributed to the combined effects of amorphous SiO,liquid Al,and the high heating rates for CAS.The flexural strength and hardness of the composite prepared by CAS were also comparable to those of compacted Ti_(3)SiC_(2)/Al_(2)O_(3) composites.