Low-temperature sintering and microwave dielectric properties of Li_2MgTi_3O_8 ceramics doped with BaCu(B_2O_5)

The influences of BaCu（B2O5） （BCB） addition on sintering, microstructure and microwave dielectric properties of Li2MgTi308 ceramics were investigated using X-ray diffractometry, scanning electron microscopy and microwave dielectric measurements. The experimental results show that a small amount of BaCu（B2O5） addition can effectively reduce the sintering temperature to 900℃, and induce only a limited degradation of the microwave dielectric properties. Typically, the best microwave dielectric properties of er24.5, Q×f =24 622 GHz, rf=4.2×10-6℃ -1 are obtained for 1.0% BCB-doped Li2MgTi3O8 ceramics sintered at 900℃ for 3 h. The BCB-doped Li2MgTi3O8 ceramics can be compatible with Ag electrode, which may be a strong candidate for low temperature co-fired ceramics applications.

Low-Temperature Sintering and Microwave DielectricProperties of Ba_2Ti_3Nb_4O_(18) Ceramics

The effects of CuO and H3BO3 additions on the low-temperature sintering,microstructure,and microwave dielectric properties of Ba2Ti3Nb4O18 ceramics were investigated.The addition of less amount of CuO （ 〈1 wt%） considerably facilitated the densification of Ba2Ti3Nb4O18 ceramics.Appropriate addition of H3BO3 （ 〈3.5 wt%） remarkably improved the microwave dielectric properties of ceramics.The addition of H3BO3 and CuO successfully reduced the sintering temperature of Ba2Ti3Nb4O18 ceramics from 1300 to 1050 ℃.Ba2Ti3Nb4O18 ceramics sintered at 1 050 ℃ for 4 h with the addition of 1.0 wt% CuO and 3.5 wt% H3BO3 exhibited good microwave dielectric properties：er=33.74,Q？f=13 812 GHz,and tf=-5.35 ppm/°C at about 5.0 GHz.

Influences of divalent ion substitution on the magnetic and dielectric properties of W-type barium ferrite

Saturation magnetization,magneto-crystalline anisotropy field,and dielectric properties are closely related to microwave devices applied at different frequencies.For regulating the magnetic and dielectric properties of W-type barium ferrites,single-phase BaMe_(2)Fe_(16)O_(27)(Me=Fe,Mn,Zn,Ni,Co) with different Me ions were synthesized by the high-temperature solid-state method.The saturation magnetization(Ms) range from 47.77 emu/g to 95.34 emu/g and the magnetic anisotropy field(H_a) range from 10700.60 Oe(1 Oe=79.5775 A·m^(-1)) to 13739.57 Oe,depending on the type of cation substitution in the hexagonal lattice.The dielectric permittivity and dielectric loss decrease with increasing frequency of the AC electric field in the low-frequency region,while they almost remain constant in the high-frequency region.The charac teristics of easy regulation and preparation make it a potential candidate for use in microwave device applications.

Achieving Synergistic Improvement in Dielectric and Energy Storage Properties of All-Organic Poly(Methyl Methacrylate)-Based Copolymers Via Establishing Charge Traps

How to achieve synergistic improvement of permittivity(ε_(r))and breakdown strength(E_(b))is a huge challenge for polymer dielectrics.Here,for the first time,theπ-conjugated comonomer(MHT)can simultaneously promote theε_(r)and E_(b)of linear poly(methyl methacrylate)(PMMA)copolymers.The PMMA-based random copolymer films(P(MMA-co-MHT)),block copolymer films(PMMA-b-PMHT),and PMMA-based blend films were prepared to investigate the effects of sequential structure,phase separation structure,and modification method on dielectric and energy storage properties of PMMA-based dielectric films.As a result,the random copolymer P(MMA-coMHT)can achieve a maximumε_(r)of 5.8 at 1 kHz owing to the enhanced orientation polarization and electron polarization.Because electron injection and charge transfer are limited by the strong electrostatic attraction ofπ-conjugated benzophenanthrene group analyzed by the density functional theory(DFT),the discharge energy density value of P(MMA-co-PMHT)containing 1 mol%MHT units with the efficiency of 80%reaches15.00 J cm^(-3)at 872 MV m^(-1),which is 165%higher than that of pure PMMA.This study provides a simple and effective way to fabricate the high performance of polymer dielectrics via copolymerization with the monomer of P-type semi-conductive polymer.

Fatigue Resistance of RCA Modified Asphalt Based on Dielectric Properties

In order to study the anti-fatigue performance of RCA modified asphalt (RMA),the performance of RMA and 90#matrix asphalt with different modifier content were measured by asphalt penetration,ductility,softening point,Brookfield viscosity,rheological index,infrared spectrum and dielectric constant test.This paper discusses the changes of asphalt basic indexes,fatigue properties and asphalt components based on dielectric properties under different modifier contents,and analyzes the grey correlation degree between components and asphalt pavement performance indexes.The results show that the optimum content of RCA modifier is 16.7%of the asphalt quality according to the penetration,ductility,softening point,Brockfield viscosity,viscosity temperature curve and fatigue life.In the phase angle-strain curve,there is disorder in the latter part of the curve.According to the strain (ε_(d)) corresponding to the disorder point,a new fatigue failure criterion is proposed and proved.Based on the new asphalt fatigue failure criterion,the fatigue prediction model of asphalt mixture is improved,and the fatigue life predicted by the improved fatigue model is compared with the fatigue life obtained by four-point bending fatigue test.The results show that the proposed new asphalt fatigue failure criterion is reasonable,and the fatigue life predicted by the improved asphalt mixture fatigue prediction model is accurate.The research method of classifying asphalt components based on dielectric properties is simple and effective,and the components have a high correlation with the road performance of base asphalt and modified asphalt.

Paraelectric Doping Simultaneously Improves the Field Frequency Adaptability and Dielectric Properties of Ferroelectric Materials:A Phase-Field Study

Recent years,the polarization response of ferroelectrics has been entirely studied.However,it is found that the polarization may disappear gradually with the continually applied of electric field.In this paper,taking K0.48Na0.52NbO3(KNN)as an example,it was demonstrated that the residual polarization began to decrease when the electric field frequency increased to a certain extent using a phase-field methods.The results showed that the content of out-of-plane domains increased first and then decreased with the increase of applied electric field frequency,the maximum polarization disappeared at high frequencies,and the hysteresis loop became elliptical.In order to further study the abnormal changes of hysteresis loops of ferroelectrics under high electric field frequency,we analyzed the hysteresis loop and dielectric response of solid solution 0.1SrTiO_(3)-0.9K_(0.48)Na_(0.52)NbO_(3).It was found that the doped hysteresis loop maintained its shape at higher frequency and the dielectric constant increased.This kind of doping has a higher field frequency adaptability,which has a key guiding role in improving the dielectric properties of ferroelectric thin films and expanding the frequency application range of ferroelectric nano memory。

Solid-state impedance spectroscopy studies of dielectric properties and relaxation processes in Na_(2)O–V_(2)O_(5)–Nb_(2)O_(5)–P_(2)O_(5) glass

Solid-state impedance spectroscopy(SS-IS)was used to investigate the influence of structural modifications resulting from the addition of Nb2O5 on the dielectric properties and relaxation processes in the quaternary mixed glass former(MGF)system 35Na_(2)O–10V_(2)O_(5)–(55-x)P_(2)O_(5)–xNb_(2)O_(5)(x=0–40,mol%).The dielectric parameters,including the dielectric strength and dielectric loss,are determined from the frequency and temperature-dependent complex permittivity data,revealing a significant dependence on the Nb2O5 content.The transition from a predominantly phosphate glass network(x<10,region I)to a mixed niobate–phosphate glass net-work(10≤x≤20,region II)leads to an increase in the dielectric parameters,which correlates with the observed trend in the direct-cur-rent(DC)conductivity.In the predominantly niobate network(x≥25,region III),the highly polarizable nature of Nb5+ions leads to a fur-ther increase in the dielectric permittivity and dielectric strength.This is particularly evident in Nb-40 glass-ceramic,which contains Na_(13)Nb_(35)O_(94) crystalline phase with a tungsten bronze structure and exhibits the highest dielectric permittivity of 61.81 and the lowest loss factor of 0.032 at 303 K and 10 kHz.The relaxation studies,analyzed through modulus formalism and complex impedance data,show that DC conductivity and relaxation processes are governed by the same mechanism,attributed to ionic conductivity.In contrast to glasses with a single peak in frequency dependence of imaginary part of electrical modulus,M″(ω),Nb-40 glass-ceramic exhibits two distinct contributions with similar relaxation times.The high-frequency peak indicates bulk ionic conductivity,while the additional low-fre-quency peak is associated with the grain boundary effect,confirmed by the electrical equivalent circuit(EEC)modelling.The scaling characteristics of permittivity and conductivity spectra,along with the electrical modulus,validate time-temperature superposition and demonstrate a strong correlation with composition and modification of the glass structure upon Nb_(2)O_(5) incorporation.

Destruction of Gaseous Styrene with a Low-Temperature Plasma Induced by a Tubular Multilayer Dielectric Barrier Discharge

The destruction of gaseous styrene was studied using a low-temperature plasma induced by tubular multilayer dielectric barrier discharge（DBD）.The results indicate that the applied voltage,gas flow rate,inlet styrene concentration and reactor configuration play important roles in styrene removal efficiency （ηstyrene） and energy yield（EY）.Values of ηstyrene and EY reached 96%and 15567 mg/kWh when the applied voltage,gas flow rate,inlet styrene concentration and layers of quartz tubes were set at 10.8 kV,5.0 m/s,229 mg/m^3 and 5 layers,respectively.A qualitative analysis of the byproducts and a detailed discussion of the reaction mechanism are also presented.The results could facilitate industrial applications of the new DBD reactor for waste gas treatment.

Effect of temperature on dielectric property and microwave heating behavior of low grade Panzhihua ilmenite ore

The permittivity of low grade Panzhuhua ilmenite ore at 2.45 GHz in the temperatures from 20 ℃ up to 100 ℃ was measured using the technology of open-ended coaxial sensor combined with theoretical computation. The results show that both the real （ε′） and imaginary （ε′） part of complex permittivity （ε′-jε′） of the ilmenite significantly increase with temperature. The loss tangent （tanδ） is a quadratic function of temperature, and the penetration depth of ilmenite decreases with temperature increase from 20 ℃to 100 ℃ The increase of the sample temperature under microwave radiation displays a nonlinear relationship between the temperature （T） and microwave heating time （t）. The positive feedback interaction between complex permittivity and sample temperature amplifies the interaction between ilmenite and the microwave radiation. The optimum dimensions for uniform heat deposition vary from 10 cm to 5 cm （about two power penetration depths） in a sample being irradiated from both sides in a 2.45 GHz microwave field when temperature increases from room temperature to 100 ℃

Influence of pyrolysis temperature on structure and dielectric properties of polycarbosilane derived silicon carbide ceramic

β-SiC ceramic powders were obtained by pyrolyzing polycarbosilane in vacuum at 800-1200 °C. The β-SiC ceramic powders were characterized by TGA/DSC, XRD and Raman spectroscopy. The dielectric properties of β-SiC ceramic powders were investigated by measuring their complex permittivity by rectangle wave guide method in the frequency range of 8.2-18 GHz. The results show that both real part ε′ and imaginary part ε″ of complex permittivity increase with increasing pyrolysis temperature. The mechanism was proposed that order carbon formed at high temperature resulted in electron relaxation polarization and conductance loss, which contributes to the increase in complex permittivity.

Dielectric properties and temperature increase characteristics of zinc oxide dust from fuming furnace

Cavity perturbation method was used to determine the dielectric properties （ε′,ε″, and tanδ） of zinc oxide dust in different apparent densities. The process was conducted to study the microwave-absorption properties of zinc oxide dust and the feasibility of microwave roasting zinc oxide dust to remove fluorine and chlorine. The dielectric constant, dielectric loss, and loss tangent were proportional to the apparent density of zinc oxide dust. The effects of sample mass and microwave power on the temperature increase characteristics under the microwave field were also studied. The results show that the apparent heating rate of the zinc oxide dust increases with the increase in microwave roasting power and decreases with the increase in the sample mass. The temperature of the samples reaches approximately 800 ＆#176;C after microwave treatment for 8 min, which indicates that the zinc oxide dust has strong microwave-absorption ability.

Dielectric properties and phase transitions of La_2O_3- and Sb_2O_3-doped barium strontium titanate ceramics

The dielectric properties and phase transition characteristics of La2O3- and Sb2O3-doped barium strontium titanate ceramics prepared by solid state route were investigated. The microstructure was identified by X-ray diffraction method and scanning electron microscope was also employed to observe the surface morphologies. It is found that （La,Sb）-codoped barium strontium titanate ceramics exhibit typical perovskite structure and the average grain size decreases dramatically with increasing the content of Sb2O3. Both La3＋ ions and Sb3＋ ions occupy the A-sites in perovskite lattice. The dielectric constant and dielectric loss of barium strontium titanate based ceramics are obviously influenced by La2O3 as well as Sb2O3 addition content. The tetragonal-cubic phase transition of La2O3 modified barium strontium titanate ceramics is of second order and the Curie temperature shifts to lower value with increasing the La2O3 doping content. The phase transition of （La,Sb）-codoped barium strontium titanate ceramics diffuses and the deviation from Curie-Weiss law becomes more obvious with the increase in Sb2O3 concentration. The temperature corresponding to the dielectric constant maximum of （La,Sb）-codoped barium strontium titanate ceramics decreases with increasing the Sb2O3 content, which is attributed to the replacement of host ions by the Sb3＋ ions.

Study on the Dielectric Properties of Chemical Vapor Deposited Diamond Film

Aim To study the dielectric properties of diamond film. Methods Dielectric properties (the frequency dependenCe of conductance, permittivity, and loss factor) of diamond film preped by DC are plasma jet chemical vapor deposition (CVD) were studied. Resuls Dielectric properties of CVD diamond fAn depend mainly on its polycrystalline nature, and the presence of non-diamond disordered graphitic regions and impurities between diamond grains of the film. Annealing at 500℃ leads to the removal of greater part of disordered graphitic regions, but am not remove all disordered graphitic regions and impurities. Conclusion Much work nab to be done tO prepare or post-treat diamond films before using CVD diamond as a substrate for electronic devices.

Microwave dielectric properties and compatibility with silver of low-fired Li_2MgTi_3O_8 ceramics with Li_2O-MgO-B_2O_3 frit

The effects of Li2O-MgO-B2O3 （LMB） glass additive on the sintering characteristics, phase purity, microstructure, and microwave dielectric properties of Li2MgTi3O8 ceramics were investigated. The experimental results demonstrate that the addition of LMB glass effectively lowers the sintering temperature of Li2MgTi3O8 ceramic from 1025 ℃ to 875 ℃ and induces no obvious degradation of the microwave dielectric properties. Typically, the 1.5%LMB glass-added Li2MgTi3O8 ceramic sintered at 875 ℃ for 4 h shows excellent microwave dielectric properties of Q×f=45403 GHz, εr=25.9 and τf≈0 ℃-1. The dielectric ceramic exhibits stability against the reaction with the Ag electrode, which indicates that the ceramics could be applied in multilayer microwave devices requiring low firing temperatures.

Dielectric and piezoelectric properties of(Li,Ce) modified NaBi_5Ti_5O_(18) composite ceramics

Nominal （Li0.5Ce0.5）x（Na0.5Bi0.5）（1-x）Na0.5Bi4.5Ti5O18 composite ceramics were fabricated using conventional solid-state reaction method. The coexistence of bismuth layer-structured phase and perovskite phase was determined in these ceramics using XRD technique. At room temperature, the x=0.11 sample showed the largest piezoelectric constant, d33, of about 26.5 pC/N and the largest electromechanical coupling factor, kt, of about 30%. Even after annealing at 500 ℃, the value of d33 was still about 19 pC/N, in x=0.08-0.11 samples. Moreover these composite ceramics showed low temperature coefficients of dielectric constant and high electrical resistivity in the temperature region of 450-550 ℃. These results indicated that （Li, Ce） modified NaBi5Ti5O18 composite ceramics were promising piezoelectric materials for high-temperature applications.

Crystallization and dielectric properties of lead-free glass-ceramic composites with Gd_2O_3 addition

Lead-free glass-ceramic composites in barium sodium niobate silica system with Gd2O3 addition were synthesized through melt-casting fol-lowed by controlled crystallization technique. Crystallization and dielectric properties of the Gd2O3 adding glass-ceramic composites were investigated. With the increase in the concentration of Gd2O3, the glass transition temperature and the crystallization temperature of the pre-cursor glass shift towards the higher temperature. The crystallization behavior that occurred during the heat treatment procedure leads to the enhancement of dielectric constant. All the three compositions of glass-ceramic composites exhibit ferroelectricity when tested at room tem-perature. Both the values of the remanent polarization and coercive field are enhanced regularly with the gradual increase in the concentration of Gd2O3 additive under the same testing field.

Dielectric Properties of Polytetrafluoroethylene/CaCu_3Ti_4O_(12) Composites

Polymer-based composite was investigated by embedding calcium copper titanate(CaCu_3Ti_4O_(12); CCTO) fillers into polytetrafluoroethylene(PTFE) matrix. The dielectric performances of the composite were investigated within the frequency range from 100 Hz to 1 MHz. It is indicated that dielectric permittivity(ε) and dielectric loss(tanδ) increase gradually as the filler content increases. Dielectric permittivity for the composite with 50 vol% CCTO filler loading is 33.5, approximately 16 times higher than that of pure PTFE(ε = 2.1) at 100 Hz. As the frequency increases, the dielectric loss decreases rapidly and reaches stability, and then remains low when the frequency rises to 1 MHz. The values for dielectric permittivity and dielectric loss in the microwave frequency(8-13 GHz) are lower than that in low frequency of 10 kHz for the composites because of different polarization modes. Several theoretical models were implemented to compare the experimental results with the theoretical calculations and the modified Lichtenecker equation was found to fit the best.

Influence of particle size and temperature on the dielectric properties of CoFe_2O_4 nanoparticles

The objective of this study was to establish the dielectric properties of CoFe2O4 nanoparticles with particle sizes that varied from 28.6 to 5.8 nm. CoFe2O4 nanoparticles were synthesized using a chemical coprecipitation method. The particle sizes were calculated accord-ing to the Scherrer formula using X-ray diffraction （XRD） peaks, and the particle size distribution curves were constructed by using field-emission scanning electron microscopy （FESEM） images. The dielectric permittivity and loss tangents of the samples were determined in the frequency range of 1 kHz to 1 MHz and in the temperature range of 300 to 10 K. Both the dielectric permittivity and the loss tangent were found to decrease with increasing frequency and decreasing temperature. For the smallest CoFe2O4 nanoparticle size, the dielectric per-mittivity and loss tangent exhibited their highest and lowest values, respectively. This behavior is very useful for materials used in devices that operate in the microwave or radio frequency ranges.

Optimized growth and dielectric properties of barium titanate thin films on polycrystalline Ni foils

Barium titanate（BTO） thin films were deposited on polycrystalline Ni foils by using the polymer assisted deposition（PAD） technique.The growth conditions including ambient and annealing temperatures were carefully optimized based on thermal dynamic analysis to control the oxidation processing and interdiffusion.Crystal structures,surface morphologies,and dielectric performance were examined and compared for BTO thin films annealed under different temperatures.Correlations between the fabrication conditions,microstructures,and dielectric properties were discussed.BTO thin films fabricated under the optimized conditions show good crystalline structure and promising dielectric properties with εr～ 400 and tan δ 〈 0.025 at 100 kHz.The data demonstrate that BTO films grown on polycrystalline Ni substrates by PAD are promising in device applications.

Dielectric Properties of Porous Reaction-boned Si_3N_4 Ceramics with Controlled Porosity and Pore Size

This paper presents the microwave dielectric properties of reaction bonded porous silicon nitride ceramics with variant porosity and pore size, which were prepared by adding pore-forming agent grains into the silicon powders. The experimental results show that the dielectric constant and the dielectric loss of the samples reduce evidently with increasing porosity in the sample. When the porosity is constant, the dielectric constant and the dielectric loss of the ceramics decrease visibly as the pore size increases. Among all the obtained samples, the minimum dielectric constant is about 2.4.