As the size of satellites scales down, low-power and compact propulsion systems such as the pulsed plasma thruster(PPT) are needed for stabilizing these miniature satellites in orbit. Most PPT systems are operated at ...As the size of satellites scales down, low-power and compact propulsion systems such as the pulsed plasma thruster(PPT) are needed for stabilizing these miniature satellites in orbit. Most PPT systems are operated at 2 J or more of discharge energy. In this work, the performance of a PPT with a side-fed, tongue-flared electrode configuration operated within a lower discharge energy range of 0.5-2.5 J has been investigated. Ablation and charring of the polytetrafluoroethylene propellant surface were analyzed through field-effect scanning electron microscopy imaging and energy-dispersive X-ray spectroscopy. When the discharge energy fell below 2 J, inconsistencies occurred in the specific impulse and the thrust efficiency due to the measurement of the low mass bit. At energy ≥2 J, the performance parameters are compared with other PPT systems of similar configuration and discussed in depth.展开更多
The destruction of gaseous styrene was studied using a low-temperature plasma induced by tubular multilayer dielectric barrier discharge(DBD).The results indicate that the applied voltage,gas flow rate,inlet styrene...The destruction of gaseous styrene was studied using a low-temperature plasma induced by tubular multilayer dielectric barrier discharge(DBD).The results indicate that the applied voltage,gas flow rate,inlet styrene concentration and reactor configuration play important roles in styrene removal efficiency (ηstyrene) and energy yield(EY).Values of ηstyrene and EY reached 96%and 15567 mg/kWh when the applied voltage,gas flow rate,inlet styrene concentration and layers of quartz tubes were set at 10.8 kV,5.0 m/s,229 mg/m^3 and 5 layers,respectively.A qualitative analysis of the byproducts and a detailed discussion of the reaction mechanism are also presented.The results could facilitate industrial applications of the new DBD reactor for waste gas treatment.展开更多
Atmospheric pressure low-temperature plasma is a promising tool in biomedicine applications including blood coagulation,bacterial inactivation,sterilization,and cancer treatment,due to its high chemical activity and l...Atmospheric pressure low-temperature plasma is a promising tool in biomedicine applications including blood coagulation,bacterial inactivation,sterilization,and cancer treatment,due to its high chemical activity and limited thermal damage.It is of great importance to develop portable plasma sources that are safe to human touch and suitable for outdoor and household operation.In this work,a portable and rechargeable low-temperature plasma spark discharge device(130 mm×80 mm×35 mm,300 g)was designed.The discharge frequency and plume length were optimized by the selection of resistance,capacitance,electrode gap,and ground electrode aperture.Results show that the spark plasma plume is generated with a length of 12 mm and a frequency of 10 Hz at a capacitance of 0.33μF.resistance of 1 MΩ,electrode gap of 2 mm,and ground electrode aperture of 1.5 mm.Biological tests indicate that the plasma produced by this device contains abundant reactive species,which can be applied in plasma biomedicine,including daily sterilization and wound healing.展开更多
The discharge morphology of pulsed dielectric barrier discharge(PDBD) plays important roles in its applications. Here, we systematically investigated the effects of the voltage amplitude,discharge gap, and O_(2)conten...The discharge morphology of pulsed dielectric barrier discharge(PDBD) plays important roles in its applications. Here, we systematically investigated the effects of the voltage amplitude,discharge gap, and O_(2)content on the PDBD morphology, and revealed the possible underlying mechanism of the U-shaped formation. First, the morphological evolution under different conditions was recorded. A unique U-shaped region appears in the middle edge region when the gap is larger than 2 mm, while the entire discharge region remains columnar under a 2 mm gap in He PDBD. The width of the discharge and the U-shaped region increase with the increase in voltage, and decrease with the increase of the gap and O_(2)content. To explain this phenomenon,a two-dimensional symmetric model was developed to simulate the spatiotemporal evolution of different species and calculate the electric thrust. The discharge morphology evolution directly corresponds to the excited-state atomic reduction process. The electric thrust on the charged particles mainly determines the reaction region and strongly influences the U-shaped formation.When the gap is less than 2 mm, the electric thrust is homogeneous throughout the entire region,resulting in a columnar shape. However, when the gap is larger than 2 mm or O_(2)is added, the electric thrust in the edge region becomes greater than that in the middle, leading to the U-shaped formation. Furthermore, in He PDBD, the charged particles generating electric thrust are mainly electrons and helium ions, while in He/O_(2)PDBD those that generate electric thrust at the outer edge of the electrode surface are mainly various oxygen-containing ions.展开更多
The discharge characteristics and mechanism of sub-millimeter pulsed dielectric barrier discharge in atmosphericpressure helium are investigated experimentally and theoretically, demonstrating that when the discharge ...The discharge characteristics and mechanism of sub-millimeter pulsed dielectric barrier discharge in atmosphericpressure helium are investigated experimentally and theoretically, demonstrating that when the discharge gap distance is reduced from 1.00 mm to 0.20 mm, the discharge ignition time is reduced to approximately 40 ns and discharge intensity is enhanced in terms of the discharge optical emission intensity and density of the plasma species,(energetic electrons with energy above 8.40 e V). The simulated results show that as the discharge gap distance is further reduced to 0.10 mm,the number of energetic electrons decreases, which is attributable to the contraction of plasma bulk regime and reduction of electron density in the discharge bulk. Conversely, the proportion of energetic electrons to the total electrons in the discharge monotonically increases as the discharge gap distance is reduced from 1.00 mm to 0.10 mm. It is proposed that a gap distance of 0.12 mm is optimal to achieve a high concentration and proportion of energetic electrons in sub-millimeter pulsed atmosphere dielectric barrier discharge.展开更多
Improving energy efficiency in plasma NO removal is a critical issue.When the surface dielectric barrier discharge(SDBD)device is considered as a combination of multiple plasma actuators,the induced plasma aerodynamic...Improving energy efficiency in plasma NO removal is a critical issue.When the surface dielectric barrier discharge(SDBD)device is considered as a combination of multiple plasma actuators,the induced plasma aerodynamic effect cannot be ignored,which can affect the mass transfer,then affect the chemical reactions.Five SDBD devices with different electrode arrangements are studied for NO conversion.They correspond to different flow patterns.We find that the energy efficiency in an SDBD device with a common structure(Type 1)is 28%lower than that in SDBD devices with a special arrangement(Types 2–5).Two reasons may explain the results.First,fewer active species are produced in Type 1 because the development of discharge is hindered by the mutually exclusive electric field forces caused by the symmetrically distributed charged particles.Second,the plasma wind induced by the plasma actuator can enhance the mass and heat transfer.The mixing of reactants and products is better in Types 2–5 than Type 1 due to higher turbulence kinetic energy.展开更多
High-voltage pulse discharge(HVPD)rock fragmentation controls a plasma channel forming inside the rock by adjusting the electrical parameters,electrode type,etc.In this work,an HVPD rock fragmentation test platform wa...High-voltage pulse discharge(HVPD)rock fragmentation controls a plasma channel forming inside the rock by adjusting the electrical parameters,electrode type,etc.In this work,an HVPD rock fragmentation test platform was built and the test waveforms were measured.Considering the effects of temperature,channel expansion and electromagnetic radiation,the impedance model of the plasma channel in the rock was established.The parameters and initial values of the model were determined by an iterative computational process.The model calculation results can reasonably characterize the development of the plasma channel in the rock and estimate the shock wave characteristics.Based on the plasma channel impedance model,the temporal and spatial distribution characteristics of the radial stress and tangential stress in the rock were calculated,and the rock fragmentation effect of the HVPD was analyzed.展开更多
Surface hydrophilicity improvement of titanium(Ti)is of great significance for the applications of the important biomaterial.In this study,efficient hydrophilicity on the Ti surface is improved by an air plasma jet ge...Surface hydrophilicity improvement of titanium(Ti)is of great significance for the applications of the important biomaterial.In this study,efficient hydrophilicity on the Ti surface is improved by an air plasma jet generated by a microhollow cathode discharge(MHCD)geometry.Elementary discharge aspects of the plasma jet and surface characteristics of the Ti surface are investigated by varying dissipated power(P_(d)).The results show that the plasma jet can operate in a pulsed mode or a continuous mode,depending on P_(d).The plume length increases with Pdand air flow rate increasing.By optical emission spectroscopy,plasma parameters as a function of Pdare investigated.After plasma treatment,water contact angel(WCA)of the Ti sample decreases to a minimum value of 15°with Pdincreasing.In addition,the surface topography,roughness,and content of chemical composition are investigated by scanning electron microscopy(SEM),atomic force microscopy(AFM),and x-ray photoelectron spectroscopy(XPS)with Pdincreasing.The results show that Ti-O bond and O-H group on the Ti surface are beneficial to the improvement of the hydrophilicity of Ti surface.展开更多
To understand the characteristics of the plasma sheath within small tubes,a 2D numerical model of He discharge within dielectric tubes is developed.During plasma propagation for a tube diameter of 0.05 mm,the sheath t...To understand the characteristics of the plasma sheath within small tubes,a 2D numerical model of He discharge within dielectric tubes is developed.During plasma propagation for a tube diameter of 0.05 mm,the sheath thickness in the plasma head is almost equal to the tube radius.It decreases rapidly to several micrometers at an axial distance of 0.05 mm behind the plasma head,and then slightly increases and saturates at the axial position far behind the plasma head.A plasma-gas sheath surrounding the central plasma column is observed for a tube diameter equal to or greater than 0.8 mm.It is replaced by a plasma-wall sheath for smaller tubes.With the decrease in the tube diameter,the sheath thickness far behind the plasma head decreases while the ion flux increases significantly.However,when O_(2)gas with a proportion of 2%is added,both the sheath thickness and ion flux decrease.展开更多
Antibiotic contamination adversely affects human health and ecological balance.In this study,gasliquid underwater discharge plasma was employed to simultaneously degrade three antibiotics,sulfadiazine(SDZ),tetracyclin...Antibiotic contamination adversely affects human health and ecological balance.In this study,gasliquid underwater discharge plasma was employed to simultaneously degrade three antibiotics,sulfadiazine(SDZ),tetracycline(TC),and norfloxacin(NOR),to address the growing problem of antibiotic contaminants in water.The effects of various parameters on the antibiotic degradation efficiency were evaluated,including the discharge gas type and flow rate,the initial concentration and pH of the solution,and the discharge voltage.Under the optimum parameter configuration,the average removal rate of the three antibiotics was 54.0% and the energy yield was 8.9 g(kW·h)-1after 5 min treatment;the removal efficiency was 96.5% and the corresponding energy yield was4.0 g(kW·h)-1 after 20 min treatment.Reactive substance capture and determination experiments indicated that ·OH and O3 played a vital role in the decomposition of SDZ and NOR,but the role of reactive substances in TC degradation was relatively less significant.展开更多
An experimental system was established to explore the plasma flow control effect for helicopter rotors in hover mode.With the plasma actuator applied at the leading edge of the rotor blades,alternating current dielect...An experimental system was established to explore the plasma flow control effect for helicopter rotors in hover mode.With the plasma actuator applied at the leading edge of the rotor blades,alternating current dielectric barrier discharge(AC-DBD) plasma actuation was generated by a sinusoidal AC high-voltage generator.By direct force measurement,the influence of actuation parameters on the aerodynamic performance of the rotor was investigated at a tip Reynolds number of 1.7 × 105.AC-DBD actuation can delay the blade stall to more than 3° with a 20%increase of about in the thrust coefficient at the post-stall pitch.At a constant motor power driving the rotor,AC-DBD actuation could reduce the rotor’s torque at the stalled pitch and increase the rotational speed of the rotor.Also,AC-DBD actuation could maintain a relatively high hover efficiency of the rotor at large collective pitches.In a wide range of actuation parameters,AC-DBD plasma actuation could improve the rotor’s aerodynamic performance at large blade pitches.High-speed photography of the tuft motion on the blade’s upper surface showed that AC-DBD plasma actuation could promote the reattachment of the blade’s separation flow.展开更多
We report five types of patterns with square symmetry,including three novel types obtained by inserting a specially designed grid photonic crystal(PC)into a dielectric barrier discharge system.They are studied using a...We report five types of patterns with square symmetry,including three novel types obtained by inserting a specially designed grid photonic crystal(PC)into a dielectric barrier discharge system.They are studied using an intensified charge-coupled device camera and photomultiplier tubes.The three novel types of patterns are a square pattern with one structure,a square superlattice pattern with four sublattices and a(1/4)K_(grid)(K_(grid)is the basic wave vector of the grid),and another square pattern with a complex inversion discharge sequence.From the application viewpoint,the five types of patterns can be used as plasma photonic crystals(PPCs).Their band diagrams under a transverse-magnetic wave simulated by the finite element method show that there are a large number of band gaps.Compared with the original PC with only a unidirectional band gap,the five types of PPCs have tunable and omnidirectional band gaps,which is very important in controlling the propagation of electromagnetic waves in the mm-wave region.The experimental results enrich the pattern types in the dielectric barrier discharge system and provide a method for obtaining PPCs with symmetry controllability and bandgap tunability.展开更多
A self-consistent fluid model is developed to investigate the radial distributions of dusty plasma parameters in a DC glow discharge,in which the extended fluid approach of plasma particles and the transport equations...A self-consistent fluid model is developed to investigate the radial distributions of dusty plasma parameters in a DC glow discharge,in which the extended fluid approach of plasma particles and the transport equations of dust particles are coupled.The electrical interaction between charged dust particles is considered in the model.The time evolution of radial distributions of dust density,plasma density,the radial component of electric field and the forces acting on dust particles when dust density tends to be stable,are obtained and analyzed under different discharge currents and dust particle radii.It is shown that the dust density structure is determined mainly by the radial electrostatic force,thermophoretic force and ion drag force in the discharge tube,and both discharge current and dust particle radius have an obvious effect on the transport processes of dust particles.The dust particles gather in the central region of the discharge tube for low discharge current and small dust radius,then dust voids are formed and become wider when the discharge current and dust radius increase.The plasma parameters in the dust gathering region are obviously affected by the dust particles due to the charging processes of electrons and ions to the dust surface.展开更多
Efficient sterilization by a plasma photocatalytic system(PPS)requires strong synergy between plasma and photocatalyst to inactivate microorganisms while suppressing the formation of secondary pollutants.Here,we repor...Efficient sterilization by a plasma photocatalytic system(PPS)requires strong synergy between plasma and photocatalyst to inactivate microorganisms while suppressing the formation of secondary pollutants.Here,we report that a PPS constructed from a needle array corona discharge and Au/TiO2plasmonic nanocatalyst could remarkably improve the sterilization of Escherichia coli(E.coli)and alleviate formation of the discharge pollutant O3.At 6 kV,the combination of corona discharge and Au/TiO2achieves sterilization efficiency of 100%within an exposure time of 5 min.At 5 kV and an exposure time of 8 min,the presence of Au/TiO2improves sterilization efficiency of the corona discharge from 73%to 91%and reduces the O3concentration from 0.38 to 0.04 ppm,whereas the presence of TiO2reduces the sterilization efficiency and O3concentration to 66%and 0.17 ppm,respectively.The Au/TiO2in the PPS enables a uniform corona discharge,enhances the interaction between plasma,E.coli and nanocatalysts,and suppresses the formation of O3.Further,the Au/TiO2can be excited by ultraviolet-visible light emitted from the plasma to generate electron-hole pairs,and thus contributes to the formation of reactive radicals and the oxidative inactivation of E.coli.The PPS constructed from a needle array corona discharge and Au-based plasmonic nanocatalyst provides a promising approach for developing high-efficiency sterilization techniques.展开更多
Sulfamethoxazole(SMX)is an antibiotic and widely present in aquatic environments,so it presents a serious threat to human health and sustainable development.A dielectric barrier discharge(DBD)plasma jet was utilized t...Sulfamethoxazole(SMX)is an antibiotic and widely present in aquatic environments,so it presents a serious threat to human health and sustainable development.A dielectric barrier discharge(DBD)plasma jet was utilized to degrade aqueous SMX,and the effects of various operating parameters(working gas,discharge power,etc)on SMX degradation performance were studied.The experimental results showed that the DBD plasma jet can obtain a relatively high degradation efficiency for SMX when the discharge power is high with an oxygen atmosphere,the initial concentration of SMX is low,and the aqueous solution is under acidic conditions.The reactive species produced in the liquid phase were detected,and OH radicals and O3were found to play a significant role in the degradation of SMX.Moreover,the process of SMX degradation could be better fitted by the quasi-first-order reaction kinetic equation.The analysis of the SMX degradation process indicated that SMX was gradually decomposed and 4-amino benzene sulfonic acid,benzene sulfonamide,4-nitro SMX,and phenylsulfinyl acid were detected,and thus three possible degradation pathways were finally proposed.The mineralization degree of SMX reached 90.04%after plasma treatment for 20 min,and the toxicity of the solution fluctuated with the discharge time but eventually decreased.展开更多
Tri-electrode sliding discharge(TED)plasma actuators are formed by adding a direct current(DC)exposed electrode to conventional dielectric barrier discharge(DBD)plasma actuators.There are three TED modes depending on ...Tri-electrode sliding discharge(TED)plasma actuators are formed by adding a direct current(DC)exposed electrode to conventional dielectric barrier discharge(DBD)plasma actuators.There are three TED modes depending on the polarity and amplitude of the DC supply:DBD discharge,extended discharge and sliding discharge.This paper evaluates the electrical,aerodynamic and mechanical characteristics of a TED plasma actuator based on energy analysis,particle image velocimetry experiments and calculations using the Navier-Stokes equation.The flow control performances of different discharge modes are quantitatively analyzed based on characteristic parameters.The results show that flow control performance in both extended discharge and sliding discharge is more significant than that of DBD,mainly because of the significantly higher(up to 141%)body force of TED compared with DBD.However,conductivity loss is the primary power loss caused by the DC polarity for TED discharge.Therefore,power consumption can be reduced by optimizing the dielectric material and thickness,thus improving the flow control performance of plasma actuators.展开更多
Atmospheric fluorocarbon plasma plays an important role in the surface modification of insulating materials like polymers.The existing fluorocarbon plasma is usually generated by dielectric barrier discharge,which has...Atmospheric fluorocarbon plasma plays an important role in the surface modification of insulating materials like polymers.The existing fluorocarbon plasma is usually generated by dielectric barrier discharge,which has a low concentration of reactive species and may cause insufficient surface fluorination.This work attempts to develop an atmospheric fluorocarbon plasma jet using a coaxial transmission line resonator by microwave discharge with locally enhanced electric field and high density.The gas temperature is reduced by pulse modulation technology.Three kinds of working gases,pure CF_(4),Ar/CF_(4)and He/CF_(4),are utilized to generate the atmospheric microwave fluorocarbon plasma jet.The discharge images,optical emission spectra,electron densities and gas temperatures are studied experimentally.The results show that the Ar/CF_(4)plasma jet has the best comprehensive performance,such as strong discharge intensity and controllable gas temperature.The electron density of the Ar/CF_4plasma jet has a magnitude of 10~(20)m^(-3),indicating a higher density than that of the frequently used dielectric barrier discharge.With the other conditions unchanged,the gas temperature at the end of the Ar/CF_(4)plasma jet can be reduced from 410.2 to 347.3 K by decreasing the duty cycle of the modulated pulse from 0.5 to 0.1.Thence,the microwave Ar/CF_(4)plasma jet is considered to be a promising fluorocarbon plasma source for surface fluorination of polymers.展开更多
The paper presents comparative kinetic characteristics of the decomposition of 2,4-dichlorophenol in a dielectric barrier discharge and a combined plasma-catalytic process. Vermiculite containing 5% zirconium was used...The paper presents comparative kinetic characteristics of the decomposition of 2,4-dichlorophenol in a dielectric barrier discharge and a combined plasma-catalytic process. Vermiculite containing 5% zirconium was used as a catalyst. The destruction processes of 2,4-DCP proceed efficiently, the degree of decomposition increases in the combined plasma-catalytic process by a factor of 1.33 and reaches 80%. The experimental results were processed according to the first-order kinetic law (R<sup>2</sup> > 0.97), according to which the effective constants (0.36 ± 0.04) and (0.51 ± 0.03) s<sup>-1</sup> and the decomposition rates of 2,4-DCP (106 and 123 μmol/l·s) when treating model solutions without a catalyst and with vermiculite + Zr 5%, respectively, and the energy costs are 0.012 and 0.017 molecules/100eV. The main decomposition products present in the solution have been determined to be carboxylic acids, aldehydes, the contribution of which does not exceed 2%, as well as chloride ions, and in the gas phase they are carbon dioxide and molecular chlorine (the share of which does not exceed 1.5% of total chlorine content in the system).展开更多
The killing logarithms index in killing a vegetative form in an explosure of about 90s and a spore in an explosure of about 120s, by using a low-temperature plasma produced by dielectric barrier discharge (DBD), rea...The killing logarithms index in killing a vegetative form in an explosure of about 90s and a spore in an explosure of about 120s, by using a low-temperature plasma produced by dielectric barrier discharge (DBD), reached 5. The speed in killing the strains tested, by using a low-temperature plasma, was the highest with E. Coli, then S. Aureus and B. Subtilis var niger spore. The results of the scanning electron microscope showed that the low-temperature plasma destroyed the outer structure of the bacteria and that the vegetative form was more susceptible to the inactivation effect of the low-temperature plasma than was the spore. This indicated that the effects of the high voltage and high velocity particle flow, in plasma, penetrating through the outer structure of the bacteria might play a dominant role during the inactivation of the bacteria.展开更多
Direct exposure of samples to the active species of air generated by a One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) has been used to etch and to increase the surface energy of metallic surfaces, photoresist, ...Direct exposure of samples to the active species of air generated by a One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) has been used to etch and to increase the surface energy of metallic surfaces, photoresist, polymer films, and nonwoven fab- rics. The OAUGDP is a non-thermal plasma with the classical characteristics of a DC normal glow discharge that operates in air (and other gases) at atmospheric pres- sure. Neither a vacuum system nor batch processing is necessary. A wide range of applications to metals, photoresist, films, fabrics, and polymeric webs can be accom- modated by direct exposure of the workpiece to the plasma in parallel-plate reactors. This technolopy is simple, it produces effects that can be obtained in no other way at one atmosphere; it generates minimal pollutants or unwanted by-products; and it is suitable for individual sample or online treatment of metallic surfaces, wafers, films, and fabrics. Early exposures of solid materials to the OAUGDP required minutes to produce rela- tively small increases of surface energy. These durations appeared too long for com- mercial application to fast-moving webs. Recent improvements in OAUGDP gas com- position, power density, plasma quality, recireulating gas flow, and impedance match- ing of the power supply to the parallel plate plasma reactor have made it possible to raise the surface energy of a variety of polymeric webs (PP, PET PE etc.) to levels of 60 to 70 dynes/cm with one second of exposure. In air plasmas, the high surface ener- gies are not durable, and fall to 50 dynes/cm after periods of weeks to months. Here, we report the exposure of metallic surfaces, photoresist, polymeric films, and nonwo- ven fabrics made of PP and PET to an impedance matched parallel plate OAUGDP for durations ranging from one second to several tens of seconds. Data will be re- ported on the surface energy, wettability, wickability, and aging effect of polymeric films and fabrics as functions of time of exposure, and time after exposure; the rate and uniformity of photoresist etching; and the production of sub-micron structures by OAUGDP etching at one atmosphere.展开更多
基金supported by the Ministry of Science,Technology and Innovation,Malaysia(MOSTI)(No.04-02-12-SF0339)。
文摘As the size of satellites scales down, low-power and compact propulsion systems such as the pulsed plasma thruster(PPT) are needed for stabilizing these miniature satellites in orbit. Most PPT systems are operated at 2 J or more of discharge energy. In this work, the performance of a PPT with a side-fed, tongue-flared electrode configuration operated within a lower discharge energy range of 0.5-2.5 J has been investigated. Ablation and charring of the polytetrafluoroethylene propellant surface were analyzed through field-effect scanning electron microscopy imaging and energy-dispersive X-ray spectroscopy. When the discharge energy fell below 2 J, inconsistencies occurred in the specific impulse and the thrust efficiency due to the measurement of the low mass bit. At energy ≥2 J, the performance parameters are compared with other PPT systems of similar configuration and discussed in depth.
基金supported by Key Project of Science and Technology Commission of Shanghai Municipality(No.13231201903)National Key Technology R&D Program of China(No.2011BAJ07B04)
文摘The destruction of gaseous styrene was studied using a low-temperature plasma induced by tubular multilayer dielectric barrier discharge(DBD).The results indicate that the applied voltage,gas flow rate,inlet styrene concentration and reactor configuration play important roles in styrene removal efficiency (ηstyrene) and energy yield(EY).Values of ηstyrene and EY reached 96%and 15567 mg/kWh when the applied voltage,gas flow rate,inlet styrene concentration and layers of quartz tubes were set at 10.8 kV,5.0 m/s,229 mg/m^3 and 5 layers,respectively.A qualitative analysis of the byproducts and a detailed discussion of the reaction mechanism are also presented.The results could facilitate industrial applications of the new DBD reactor for waste gas treatment.
基金supported by National Natural Science Foundation of China(Nos.51677083 and 51377075)Postgraduate Research and Practice Innovation Program of Jiangsu Province(SJCX18_0340)
文摘Atmospheric pressure low-temperature plasma is a promising tool in biomedicine applications including blood coagulation,bacterial inactivation,sterilization,and cancer treatment,due to its high chemical activity and limited thermal damage.It is of great importance to develop portable plasma sources that are safe to human touch and suitable for outdoor and household operation.In this work,a portable and rechargeable low-temperature plasma spark discharge device(130 mm×80 mm×35 mm,300 g)was designed.The discharge frequency and plume length were optimized by the selection of resistance,capacitance,electrode gap,and ground electrode aperture.Results show that the spark plasma plume is generated with a length of 12 mm and a frequency of 10 Hz at a capacitance of 0.33μF.resistance of 1 MΩ,electrode gap of 2 mm,and ground electrode aperture of 1.5 mm.Biological tests indicate that the plasma produced by this device contains abundant reactive species,which can be applied in plasma biomedicine,including daily sterilization and wound healing.
基金financial support from the Interdisciplinary Fund of the Wuhan National High Magnetic Field Center (No. WHMFC202101)。
文摘The discharge morphology of pulsed dielectric barrier discharge(PDBD) plays important roles in its applications. Here, we systematically investigated the effects of the voltage amplitude,discharge gap, and O_(2)content on the PDBD morphology, and revealed the possible underlying mechanism of the U-shaped formation. First, the morphological evolution under different conditions was recorded. A unique U-shaped region appears in the middle edge region when the gap is larger than 2 mm, while the entire discharge region remains columnar under a 2 mm gap in He PDBD. The width of the discharge and the U-shaped region increase with the increase in voltage, and decrease with the increase of the gap and O_(2)content. To explain this phenomenon,a two-dimensional symmetric model was developed to simulate the spatiotemporal evolution of different species and calculate the electric thrust. The discharge morphology evolution directly corresponds to the excited-state atomic reduction process. The electric thrust on the charged particles mainly determines the reaction region and strongly influences the U-shaped formation.When the gap is less than 2 mm, the electric thrust is homogeneous throughout the entire region,resulting in a columnar shape. However, when the gap is larger than 2 mm or O_(2)is added, the electric thrust in the edge region becomes greater than that in the middle, leading to the U-shaped formation. Furthermore, in He PDBD, the charged particles generating electric thrust are mainly electrons and helium ions, while in He/O_(2)PDBD those that generate electric thrust at the outer edge of the electrode surface are mainly various oxygen-containing ions.
基金Project supported by the National Natural Science Foundation of China (Grant Nos.12175036 and 11875104)。
文摘The discharge characteristics and mechanism of sub-millimeter pulsed dielectric barrier discharge in atmosphericpressure helium are investigated experimentally and theoretically, demonstrating that when the discharge gap distance is reduced from 1.00 mm to 0.20 mm, the discharge ignition time is reduced to approximately 40 ns and discharge intensity is enhanced in terms of the discharge optical emission intensity and density of the plasma species,(energetic electrons with energy above 8.40 e V). The simulated results show that as the discharge gap distance is further reduced to 0.10 mm,the number of energetic electrons decreases, which is attributable to the contraction of plasma bulk regime and reduction of electron density in the discharge bulk. Conversely, the proportion of energetic electrons to the total electrons in the discharge monotonically increases as the discharge gap distance is reduced from 1.00 mm to 0.10 mm. It is proposed that a gap distance of 0.12 mm is optimal to achieve a high concentration and proportion of energetic electrons in sub-millimeter pulsed atmosphere dielectric barrier discharge.
基金supported by the National Natural Science Foundation of China(60906053,61204069,61274118,61306144,61504079,and 11605112)Scientific and Innovative Action Plan of Shanghai(15DZ1160800 and 17XD1702400)China Postdoctoral Science Foundation(2016 M601595).
文摘Improving energy efficiency in plasma NO removal is a critical issue.When the surface dielectric barrier discharge(SDBD)device is considered as a combination of multiple plasma actuators,the induced plasma aerodynamic effect cannot be ignored,which can affect the mass transfer,then affect the chemical reactions.Five SDBD devices with different electrode arrangements are studied for NO conversion.They correspond to different flow patterns.We find that the energy efficiency in an SDBD device with a common structure(Type 1)is 28%lower than that in SDBD devices with a special arrangement(Types 2–5).Two reasons may explain the results.First,fewer active species are produced in Type 1 because the development of discharge is hindered by the mutually exclusive electric field forces caused by the symmetrically distributed charged particles.Second,the plasma wind induced by the plasma actuator can enhance the mass and heat transfer.The mixing of reactants and products is better in Types 2–5 than Type 1 due to higher turbulence kinetic energy.
基金support of National Natural Science Foundation of China(No.52177144)。
文摘High-voltage pulse discharge(HVPD)rock fragmentation controls a plasma channel forming inside the rock by adjusting the electrical parameters,electrode type,etc.In this work,an HVPD rock fragmentation test platform was built and the test waveforms were measured.Considering the effects of temperature,channel expansion and electromagnetic radiation,the impedance model of the plasma channel in the rock was established.The parameters and initial values of the model were determined by an iterative computational process.The model calculation results can reasonably characterize the development of the plasma channel in the rock and estimate the shock wave characteristics.Based on the plasma channel impedance model,the temporal and spatial distribution characteristics of the radial stress and tangential stress in the rock were calculated,and the rock fragmentation effect of the HVPD was analyzed.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51977057 and 11875121)the Natural Science Foundation of Hebei Province,China(Grant Nos.A2020201025 and A2022201036)+2 种基金the Natural Science Interdisciplinary Research Program of Hebei University,China(Grant Nos.DXK201908 and DXK202011)the Postgraduate’s Innovation Fund Project of Hebei Province,China(Grant Nos.CXZZBS2019023 and CXZZBS2019029)the Post-graduate’s Innovation Fund Project of Hebei University,China(Grant Nos.HBU2021ss063,HBU2021bs011,and HBU2022bs004)。
文摘Surface hydrophilicity improvement of titanium(Ti)is of great significance for the applications of the important biomaterial.In this study,efficient hydrophilicity on the Ti surface is improved by an air plasma jet generated by a microhollow cathode discharge(MHCD)geometry.Elementary discharge aspects of the plasma jet and surface characteristics of the Ti surface are investigated by varying dissipated power(P_(d)).The results show that the plasma jet can operate in a pulsed mode or a continuous mode,depending on P_(d).The plume length increases with Pdand air flow rate increasing.By optical emission spectroscopy,plasma parameters as a function of Pdare investigated.After plasma treatment,water contact angel(WCA)of the Ti sample decreases to a minimum value of 15°with Pdincreasing.In addition,the surface topography,roughness,and content of chemical composition are investigated by scanning electron microscopy(SEM),atomic force microscopy(AFM),and x-ray photoelectron spectroscopy(XPS)with Pdincreasing.The results show that Ti-O bond and O-H group on the Ti surface are beneficial to the improvement of the hydrophilicity of Ti surface.
基金supported by National Natural Science Foundation of China(No.51977110)。
文摘To understand the characteristics of the plasma sheath within small tubes,a 2D numerical model of He discharge within dielectric tubes is developed.During plasma propagation for a tube diameter of 0.05 mm,the sheath thickness in the plasma head is almost equal to the tube radius.It decreases rapidly to several micrometers at an axial distance of 0.05 mm behind the plasma head,and then slightly increases and saturates at the axial position far behind the plasma head.A plasma-gas sheath surrounding the central plasma column is observed for a tube diameter equal to or greater than 0.8 mm.It is replaced by a plasma-wall sheath for smaller tubes.With the decrease in the tube diameter,the sheath thickness far behind the plasma head decreases while the ion flux increases significantly.However,when O_(2)gas with a proportion of 2%is added,both the sheath thickness and ion flux decrease.
基金supported by the Key R&D Plan of Anhui Province(No.201904a07020013)Collaborative Innovation Program of Hefei Science Center,CAS(No.CX2140000018)the Funding for Joint Lab of Applied Plasma Technology(No.JL06120001H)。
文摘Antibiotic contamination adversely affects human health and ecological balance.In this study,gasliquid underwater discharge plasma was employed to simultaneously degrade three antibiotics,sulfadiazine(SDZ),tetracycline(TC),and norfloxacin(NOR),to address the growing problem of antibiotic contaminants in water.The effects of various parameters on the antibiotic degradation efficiency were evaluated,including the discharge gas type and flow rate,the initial concentration and pH of the solution,and the discharge voltage.Under the optimum parameter configuration,the average removal rate of the three antibiotics was 54.0% and the energy yield was 8.9 g(kW·h)-1after 5 min treatment;the removal efficiency was 96.5% and the corresponding energy yield was4.0 g(kW·h)-1 after 20 min treatment.Reactive substance capture and determination experiments indicated that ·OH and O3 played a vital role in the decomposition of SDZ and NOR,but the role of reactive substances in TC degradation was relatively less significant.
文摘An experimental system was established to explore the plasma flow control effect for helicopter rotors in hover mode.With the plasma actuator applied at the leading edge of the rotor blades,alternating current dielectric barrier discharge(AC-DBD) plasma actuation was generated by a sinusoidal AC high-voltage generator.By direct force measurement,the influence of actuation parameters on the aerodynamic performance of the rotor was investigated at a tip Reynolds number of 1.7 × 105.AC-DBD actuation can delay the blade stall to more than 3° with a 20%increase of about in the thrust coefficient at the post-stall pitch.At a constant motor power driving the rotor,AC-DBD actuation could reduce the rotor’s torque at the stalled pitch and increase the rotational speed of the rotor.Also,AC-DBD actuation could maintain a relatively high hover efficiency of the rotor at large collective pitches.In a wide range of actuation parameters,AC-DBD plasma actuation could improve the rotor’s aerodynamic performance at large blade pitches.High-speed photography of the tuft motion on the blade’s upper surface showed that AC-DBD plasma actuation could promote the reattachment of the blade’s separation flow.
基金supported by National Natural Science Foundation of China(No.12075075)the Natural Science Foundation of Hebei Province, China(Nos.2020201016 and A2018201154)。
文摘We report five types of patterns with square symmetry,including three novel types obtained by inserting a specially designed grid photonic crystal(PC)into a dielectric barrier discharge system.They are studied using an intensified charge-coupled device camera and photomultiplier tubes.The three novel types of patterns are a square pattern with one structure,a square superlattice pattern with four sublattices and a(1/4)K_(grid)(K_(grid)is the basic wave vector of the grid),and another square pattern with a complex inversion discharge sequence.From the application viewpoint,the five types of patterns can be used as plasma photonic crystals(PPCs).Their band diagrams under a transverse-magnetic wave simulated by the finite element method show that there are a large number of band gaps.Compared with the original PC with only a unidirectional band gap,the five types of PPCs have tunable and omnidirectional band gaps,which is very important in controlling the propagation of electromagnetic waves in the mm-wave region.The experimental results enrich the pattern types in the dielectric barrier discharge system and provide a method for obtaining PPCs with symmetry controllability and bandgap tunability.
基金supported by the Stable-Support Scientific Project of China Research Institute of Radiowave Propagation(No.132101W07)National Natural Science Foundation of China(No.12105251)National Key Laboratory Foundation Electromagnetic Environment(Nos.A382101001,A382101002 and A152101731-C02).
文摘A self-consistent fluid model is developed to investigate the radial distributions of dusty plasma parameters in a DC glow discharge,in which the extended fluid approach of plasma particles and the transport equations of dust particles are coupled.The electrical interaction between charged dust particles is considered in the model.The time evolution of radial distributions of dust density,plasma density,the radial component of electric field and the forces acting on dust particles when dust density tends to be stable,are obtained and analyzed under different discharge currents and dust particle radii.It is shown that the dust density structure is determined mainly by the radial electrostatic force,thermophoretic force and ion drag force in the discharge tube,and both discharge current and dust particle radius have an obvious effect on the transport processes of dust particles.The dust particles gather in the central region of the discharge tube for low discharge current and small dust radius,then dust voids are formed and become wider when the discharge current and dust radius increase.The plasma parameters in the dust gathering region are obviously affected by the dust particles due to the charging processes of electrons and ions to the dust surface.
基金National Natural Science Foundation of China(Nos.52041001,21808024)Natural Science Foundation of Liaoning Province(No.2020-MS-126)Special Foundation for Key Fields of Colleges and Universities in Guangdong Province(No.2021ZDZX4094)。
文摘Efficient sterilization by a plasma photocatalytic system(PPS)requires strong synergy between plasma and photocatalyst to inactivate microorganisms while suppressing the formation of secondary pollutants.Here,we report that a PPS constructed from a needle array corona discharge and Au/TiO2plasmonic nanocatalyst could remarkably improve the sterilization of Escherichia coli(E.coli)and alleviate formation of the discharge pollutant O3.At 6 kV,the combination of corona discharge and Au/TiO2achieves sterilization efficiency of 100%within an exposure time of 5 min.At 5 kV and an exposure time of 8 min,the presence of Au/TiO2improves sterilization efficiency of the corona discharge from 73%to 91%and reduces the O3concentration from 0.38 to 0.04 ppm,whereas the presence of TiO2reduces the sterilization efficiency and O3concentration to 66%and 0.17 ppm,respectively.The Au/TiO2in the PPS enables a uniform corona discharge,enhances the interaction between plasma,E.coli and nanocatalysts,and suppresses the formation of O3.Further,the Au/TiO2can be excited by ultraviolet-visible light emitted from the plasma to generate electron-hole pairs,and thus contributes to the formation of reactive radicals and the oxidative inactivation of E.coli.The PPS constructed from a needle array corona discharge and Au-based plasmonic nanocatalyst provides a promising approach for developing high-efficiency sterilization techniques.
基金supported jointly by National Natural Science Foundation of China(Nos.U20A20372,51807046,51777206)the Natural Science Foundation of Anhui Province(Nos.2108085MD136,1908085MA29)。
文摘Sulfamethoxazole(SMX)is an antibiotic and widely present in aquatic environments,so it presents a serious threat to human health and sustainable development.A dielectric barrier discharge(DBD)plasma jet was utilized to degrade aqueous SMX,and the effects of various operating parameters(working gas,discharge power,etc)on SMX degradation performance were studied.The experimental results showed that the DBD plasma jet can obtain a relatively high degradation efficiency for SMX when the discharge power is high with an oxygen atmosphere,the initial concentration of SMX is low,and the aqueous solution is under acidic conditions.The reactive species produced in the liquid phase were detected,and OH radicals and O3were found to play a significant role in the degradation of SMX.Moreover,the process of SMX degradation could be better fitted by the quasi-first-order reaction kinetic equation.The analysis of the SMX degradation process indicated that SMX was gradually decomposed and 4-amino benzene sulfonic acid,benzene sulfonamide,4-nitro SMX,and phenylsulfinyl acid were detected,and thus three possible degradation pathways were finally proposed.The mineralization degree of SMX reached 90.04%after plasma treatment for 20 min,and the toxicity of the solution fluctuated with the discharge time but eventually decreased.
基金the National Natural Science Foundation of China(Grant Nos.12175177 and 61971345)the Foundation for Key Laboratories of National Defense Science and Technology of China(Grant No.614220120030810)。
文摘Tri-electrode sliding discharge(TED)plasma actuators are formed by adding a direct current(DC)exposed electrode to conventional dielectric barrier discharge(DBD)plasma actuators.There are three TED modes depending on the polarity and amplitude of the DC supply:DBD discharge,extended discharge and sliding discharge.This paper evaluates the electrical,aerodynamic and mechanical characteristics of a TED plasma actuator based on energy analysis,particle image velocimetry experiments and calculations using the Navier-Stokes equation.The flow control performances of different discharge modes are quantitatively analyzed based on characteristic parameters.The results show that flow control performance in both extended discharge and sliding discharge is more significant than that of DBD,mainly because of the significantly higher(up to 141%)body force of TED compared with DBD.However,conductivity loss is the primary power loss caused by the DC polarity for TED discharge.Therefore,power consumption can be reduced by optimizing the dielectric material and thickness,thus improving the flow control performance of plasma actuators.
基金partly supported by National Natural Science Foundation of China(Nos.52207147 and 52177126)the Anhui Provincial Natural Science Foundation(Nos.2208085QE168 and 2108085ME180)the Anhui Provincial Natural Science Research Project of Higher Education(No.2022AH050301)。
文摘Atmospheric fluorocarbon plasma plays an important role in the surface modification of insulating materials like polymers.The existing fluorocarbon plasma is usually generated by dielectric barrier discharge,which has a low concentration of reactive species and may cause insufficient surface fluorination.This work attempts to develop an atmospheric fluorocarbon plasma jet using a coaxial transmission line resonator by microwave discharge with locally enhanced electric field and high density.The gas temperature is reduced by pulse modulation technology.Three kinds of working gases,pure CF_(4),Ar/CF_(4)and He/CF_(4),are utilized to generate the atmospheric microwave fluorocarbon plasma jet.The discharge images,optical emission spectra,electron densities and gas temperatures are studied experimentally.The results show that the Ar/CF_(4)plasma jet has the best comprehensive performance,such as strong discharge intensity and controllable gas temperature.The electron density of the Ar/CF_4plasma jet has a magnitude of 10~(20)m^(-3),indicating a higher density than that of the frequently used dielectric barrier discharge.With the other conditions unchanged,the gas temperature at the end of the Ar/CF_(4)plasma jet can be reduced from 410.2 to 347.3 K by decreasing the duty cycle of the modulated pulse from 0.5 to 0.1.Thence,the microwave Ar/CF_(4)plasma jet is considered to be a promising fluorocarbon plasma source for surface fluorination of polymers.
文摘The paper presents comparative kinetic characteristics of the decomposition of 2,4-dichlorophenol in a dielectric barrier discharge and a combined plasma-catalytic process. Vermiculite containing 5% zirconium was used as a catalyst. The destruction processes of 2,4-DCP proceed efficiently, the degree of decomposition increases in the combined plasma-catalytic process by a factor of 1.33 and reaches 80%. The experimental results were processed according to the first-order kinetic law (R<sup>2</sup> > 0.97), according to which the effective constants (0.36 ± 0.04) and (0.51 ± 0.03) s<sup>-1</sup> and the decomposition rates of 2,4-DCP (106 and 123 μmol/l·s) when treating model solutions without a catalyst and with vermiculite + Zr 5%, respectively, and the energy costs are 0.012 and 0.017 molecules/100eV. The main decomposition products present in the solution have been determined to be carboxylic acids, aldehydes, the contribution of which does not exceed 2%, as well as chloride ions, and in the gas phase they are carbon dioxide and molecular chlorine (the share of which does not exceed 1.5% of total chlorine content in the system).
文摘The killing logarithms index in killing a vegetative form in an explosure of about 90s and a spore in an explosure of about 120s, by using a low-temperature plasma produced by dielectric barrier discharge (DBD), reached 5. The speed in killing the strains tested, by using a low-temperature plasma, was the highest with E. Coli, then S. Aureus and B. Subtilis var niger spore. The results of the scanning electron microscope showed that the low-temperature plasma destroyed the outer structure of the bacteria and that the vegetative form was more susceptible to the inactivation effect of the low-temperature plasma than was the spore. This indicated that the effects of the high voltage and high velocity particle flow, in plasma, penetrating through the outer structure of the bacteria might play a dominant role during the inactivation of the bacteria.
文摘Direct exposure of samples to the active species of air generated by a One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) has been used to etch and to increase the surface energy of metallic surfaces, photoresist, polymer films, and nonwoven fab- rics. The OAUGDP is a non-thermal plasma with the classical characteristics of a DC normal glow discharge that operates in air (and other gases) at atmospheric pres- sure. Neither a vacuum system nor batch processing is necessary. A wide range of applications to metals, photoresist, films, fabrics, and polymeric webs can be accom- modated by direct exposure of the workpiece to the plasma in parallel-plate reactors. This technolopy is simple, it produces effects that can be obtained in no other way at one atmosphere; it generates minimal pollutants or unwanted by-products; and it is suitable for individual sample or online treatment of metallic surfaces, wafers, films, and fabrics. Early exposures of solid materials to the OAUGDP required minutes to produce rela- tively small increases of surface energy. These durations appeared too long for com- mercial application to fast-moving webs. Recent improvements in OAUGDP gas com- position, power density, plasma quality, recireulating gas flow, and impedance match- ing of the power supply to the parallel plate plasma reactor have made it possible to raise the surface energy of a variety of polymeric webs (PP, PET PE etc.) to levels of 60 to 70 dynes/cm with one second of exposure. In air plasmas, the high surface ener- gies are not durable, and fall to 50 dynes/cm after periods of weeks to months. Here, we report the exposure of metallic surfaces, photoresist, polymeric films, and nonwo- ven fabrics made of PP and PET to an impedance matched parallel plate OAUGDP for durations ranging from one second to several tens of seconds. Data will be re- ported on the surface energy, wettability, wickability, and aging effect of polymeric films and fabrics as functions of time of exposure, and time after exposure; the rate and uniformity of photoresist etching; and the production of sub-micron structures by OAUGDP etching at one atmosphere.