Effects of Potassium Ferrate and Low-Temperature Thermal Hydrolysis Co-Pretreatment on the Hydrolysis and Anaerobic Digestion Process of Waste Activated Sludge

This study evaluated the effect of potassium ferrate(PF)and low-temperature thermal hydrolysis co-pretreatment on the promotion of sludge hydrolysis process and the impact on acid production in the subsequent anaerobic digestion process.The analytical investigations showed that co-pretreatment significantly facilitated the hydrolysis process of the sludge and contributed to the accumulation of short-chain fatty acids(SCFAs).The pretreatment conditions under the optimal leaching of organic matter from sludge were hydrothermal temperature of 75℃,hydrothermal treatment time of 12 h,and PF dosage of 0.25 g g^(−1)TSS(total suspended solids),according to the results of orthogonal experiments.By pretreatment under proper conditions,the removal rate of soluble chemical oxygen demand(SCOD)achieved 71.8%at the end of fermentation and the removal rate of total phosphorus(TP)was 69.1%.The maximum yield of SCFAs was 750.3 mg L^(−1),7.45 times greater than that of the blank group.Based on the analysis of the anaerobic digestion mechanism,it was indicated that the co-pretreatment could destroy the floc structure on the sludge surface and improve organic matter dissolving,resulting in more soluble organic substances for the acidification process.Furthermore,microbial community research revealed that the main cause of enhanced SCFAs generation was an increase in acidogenic bacteria and a reduction of methanogenic bacteria.

Utilization and recycling of low-temperature waste heat of stainless steel continuous annealing furnace

Stainless steel continuous annealing furnace is mainly used for heat treatment of hot-rolled strip steel.The combustion air will be enabled to heat to 520℃by waste heat recovery system,but the discharge temperature is still up to about 300℃.Owing to with development of global emphasis on energy conservation energy saving and discharge reduction,it's significant to lower the discharge temperature to below 200℃, for the sake of achieving rational use of waste heat resource.Through the analysis of the existing heat recovery system by this study,it is proved that mixing low temperature with flue gas in high temperature standard will increase the capacity of the flue gas and deteriorate the quality of remaining heat resource.In stead of that,increasing the combustion air temperature to 600℃on the basis of stability temperature for the prerequisite of recuperator design,and giving priority to reducing fuel consumption are the better way.The recovery and recycle of low temperature gas are also be introduced.It is demonstrated by the way of setting a secondary recuperator at the exit of the primary recuperator,and using low temperature flue gas to heat the air used for drying the strip steel,the exhuast temperature of flue gas can be reduced to lower than 200℃.At the same time,the steam required for heating air is saved,the energy reserve as high as 2 300 t of standard coal per year.

Heat Transfer and Energy Utilization of Waste Heat Recovery Device with Different Internal Component

Steel industry is high energy-consuming industry, and its waste?heat recovery is critically?important for energy utilization. In this study, pipeline bundle is used to enhance heat transfer in?waste?heat recovery device,?and?associated gas-solid heat transfer and energy utilization performance with different pipeline arrangement, pipe diameter and shape of internal component are further analyzed. The temperatures of gas and particle in device with pipeline bundle periodically fluctuate in horizontal direction, and those in staggered system distribute more uniformly than those in paralleled system. Compared with paralleled device, exergy and waste heat utilization efficiency of staggered device have been improved, and they are both higher than?those without pipeline. As pipe diameter increases, exergy and waste heat utilization efficiency first increases and then decreases, and they reach the maxima with optimal pipe diameter.?As the width of internal component keeps constant, influence of its shape on heat transfer is very little.

Technical Measures and Selections for Reducing Flue Gas Heat Loss of Large Coal-Fired Boilers

The main technologies for reducing flue gas heat loss of pulverized coal-fired boilers are introduced, and the suitability of these technologies for boiler operation and the principles for selection of these technologies are explored. The main conclusions are： 1） the non-equilibrium control over flue gas flow rates at the inlet of the air heater and the reversal rotation of the air heater rotator should be popularized as regular technologies in large boilers; 2） increasing the area of the air heater to reduce the flue gas heat loss in pulverized coal-fired boilers should be the top option and increasing the area of the economizer be the next choice; 3） low- pressure economizer technology could save energy under special conditions and should be compared with the technology of increasing economizer area in terms of technical economics when the latter is feasible; 4） the hot primary air heater is only suitable to the pnlvefizing system with a large amount of cold air mixed.

HEAVY METAL PARTITIONING IN A NUCLEAR WASTE TREATMENT PLANT

The fate of different trace elements and radio nuclides in the new ZWILAG nuclear waste treatment plant （Switzerland） has been modelled, in order to predict and check the transport behaviour of the volatile species and their distribution in the plant. Calculations show that for active waste from medicine, industry, research （MIR waste） only Zn and Cs have stable gaseous species at 1200℃. The investigations confirm the efficiency of the examined flue gas cleaning system.