Co-doped BaFe_(2)As_(2) Josephson junction fabricated with a focused helium ion beam

Josephson junction plays a key role not only in studying the basic physics of unconventional iron-based superconductors but also in realizing practical application of thin-film based devices,therefore the preparation of high-quality iron pnictide Josephson junctions is of great importance.In this work,we have successfully fabricated Josephson junctions from Co-doped BaFe_(2)As_(2)thin films using a direct junction fabrication technique which utilizes high energy focused helium ion beam(FHIB).The electrical transport properties were investigated for junctions fabricated with various He^(+)irradiation doses.The junctions show sharp superconducting transition around 24 K with a narrow transition width of 2.5 K,and a dose correlated foot-structure resistance which corresponds to the effective tuning of junction properties by He^(+)irradiation.Significant J_c suppression by more than two orders of magnitude can be achieved by increasing the He^(+)irradiation dose,which is advantageous for the realization of low noise ion pnictide thin film devices.Clear Shapiro steps are observed under 10 GHz microwave irradiation.The above results demonstrate the successful fabrication of high quality and controllable Co-doped BaFe_(2)As_(2)Josephson junction with high reproducibility using the FHIB technique,laying the foundation for future investigating the mechanism of iron-based superconductors,and also the further implementation in various superconducting electronic devices.

The Electrocatalytic Performance of Rare Earth Ion Doped Co_(0.2)Ni_(0.8)-MOF-74 Catalyst for Nitrogen Reduction

We took Co_(0.2)Ni_(0.8)-MOF-74 with bimetallic synergistic effect as the basic material,and selected rare earth ions Ho,Gd,and Er with ion radii close to Co and Ni as the research objects for doping.The influence of rare earth ion doping amount and doping type on the eNRR performance of the catalyst was explored.The experimental results show that the ammonia yield rate and Faraday efficiency doped with Co_(0.2)Ni_(0.8)-MOF-0.5Ho are the highest,reaching 1.28×10^(-10)mol·s^(-1)·cm^(-2)/39.8%,which is higher than the1.12×10^(-10)mol·s^(-1)·cm^(-2)/32.2%of Co_(0.2)Ni_(0.8)-MOF-74,and is about 14.3%/23.7%higher than that without doping,respectively.And the stability of Co_(0.2)Ni_(0.8)-MOF-0.5 Ho is good(after 80 hours of continuous testing,the current density did not significantly decrease).This is mainly due to doping,which gives Co_(0.2)Ni_(0.8)-MOF-74 a larger specific surface area and catalytic active sites.The catalyst doped at the same time has more metal cation centers,which increases the electron density of the metal centers and enhances the corresponding eNRR performance.

Progress in doping and crystal deformation for polyanions cathode based lithium-ion batteries

Polyanion-based materials are considered one of the most attractive and promising cathode materials for lithiumion batteries(LIBs)due to their good stability,safety,cost-effectiveness,suitable voltages,and minimal environmental impact.However,these materials suffer from poor rate capability and low-temperature performance owing to limited electronic and ionic conductivity,which restricts their practical applicability.Recent developments,such as coating material particles with carbon or a conductive polymer,crystal deformation through the doping of foreign metal ions,and the production of nanostructured materials,have significantly enhanced the electrochemical performances of these materials.The successful applications of polyanion-based materials,especially in lithium-ion batteries,have been extensively reported.This comprehensive review discusses the current progress in crystal deformation in polyanion-based cathode materials,including phosphates,fluorophosphates,pyrophosphates,borates,silicates,sulfates,fluorosilicates,and oxalates.Therefore,this review provides detailed discussions on their synthesis strategies,electrochemical performance,and the doping of various ions.

Effect of Mn-doping on performance of Li_3V_2(PO_4)_3/C cathode material for lithium ion batteries

Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galvanostatic charge /discharge and electrochemical impedance spectroscopy（EIS）. The XRD study shows that a small amount of Mn2＋-doped does not alter the structure of Li3V2（PO4）3/C materials, and all Mn2＋-doped samples are of pure single phase with a monoclinic structure （space group P21/n）. The XPS analysis indicates that valences state of V and Mn are ＋3 and ＋2 in Li3V1.94Mn0.09（PO4）3/C, respectively, and the citric acid in raw materials was decomposed into carbon during calcination, and residual carbon exists in Li3V1.94Mn0.09（PO4）/C. The results of electrochemical measurements show that Mn2＋-doping can improve the cyclic stability and rate performance of these cathode materials. The Li3V1.94Mn0.09（PO4）3/C cathode material shows the best cyclic stability and rate performance. For example, at the discharge current density of 40 mA/g, after 100 cycles, the discharge capacity of Li3V1.94Mn0.09（PO4）3/C declines from initial 158.8 mA·h/g to 120.5 mA·h/g with a capacity retention of 75.9%; however, that of the Mn-undoed sample declines from 164.2 mA·h/g to 72.6 mA·h/g with a capacity retention of 44.2%. When the discharge current is increased up to 1C, the intial discharge capacity of Li3V1.94Mn0.09（PO4）3/C still reaches 146.4 mA·h/g, and the discharge capacity maintains at 107.5 mA·h/g after 100 cycles. The EIS measurement indicates that Mn2＋-doping with a appropriate amount of Mn2＋ decreases the charge transfer resistance, which is favorable for the insertion/extraction of Li＋.

Synthesis and characterization of LiFePO_4 coating with aluminum doped zinc oxide

Aluminum doped zinc oxide （AZO）, as an electrically conductive material, was applied to coating on the surface of olivine-type LiFePO4 synthesized by solid-state method. The charge-discharge test results show that the rate performance and low-temperature performance of LiFePO4 are greatly improved by the surface treatment. Even at 20C rate, the discharge specific capacity of 100.9 mA.h/g was obtained by the AZO-coated LiFePO4 at room temperature. At -20 ℃, the discharge specific capacity at 0.2C for un-coated LiFePO4 and the coated one are 50.3 mA.h/g and 119.4 mA.h/g, respectively. It should be attributed to the electrically conductive AZO-coating which increases the electronic conductivity of LiFePO4. Furthermore, the surface-coating increases the tap-density of LiFePO4. The results indicate that the AZO-coated LiFePO4 is a good candidate of cathode material for applying in lithium power batteries.

Nitrogen and Phosphorus Dual-Doped Multilayer Graphene as Universal Anode for Full Carbon-Based Lithium and Potassium Ion Capacitors

Lithium/potassium ion capacitors(LICs/PICs) have been proposed to bridge the performance gap between high-energy batteries and high-power capacitors.However,their development is hindered by the choice,electrochemical performance,and preparation technique of the battery-type anode materials.Herein,a nitrogen and phosphorus dual-doped multilayer graphene(NPG) material is designed and synthesized through an arc discharge process,using low-cost graphite and solid nitrogen and phosphorus sources.When employed as the anode material,NPG exhibits high capacity,remarkable rate capability,and stable cycling performance in both lithium and potassium ion batteries.This excellent electrochemical performance is ascribed to the synergistic effect of nitrogen and phosphorus doping,which enhances the electrochemical conductivity,provides a higher number of ion storage sites,and leads to increased interlayer spacing.Full carbon-based NPG‖LiPF6‖active carbon(AC) LICs and NPG‖KPF6‖AC PICs are assembled and show excellent electrochemical performance,with competitive energy and power densities.This work provides a route for the large-scale production of dual-doped graphene as a universal anode material for high-performance alkali ion batteries and capacitors.

Characterization of metal doped-titanium dioxide and behaviors on photocatalytic oxidation of nitrogen oxides

A series of nanosized ion-doped TiO2 catalysts with different ion content （between 0.1 at.% and 1.0 at.%） have been prepared by wet impregnation method and investigated with respect to their behavior for UV photocatalytic oxidation of nitric oxide. The catalytic activity was correlated with structural, electronic and surface examinations of the catalysts using X-ray diffraction analysis （XRD）, ultraviolet-visible （UV-Vis） absorption spectroscopy, transmission electron microscopy （TEM）, energy disperse spectrometer （EDS） and high resolution-transmission electron microscopy （HR-TEM） techniques. An enhancement of the photocatalytic activity was observed for Zn2＋ doping catalyst ranged from 0.1 at.% to 1.0 at.% which was attributed to the lengthened lifetime of electrons and holes. The improvement in photocatalytic activity could be also observed with the low doping concentration of Cr^3＋ （0.1 at.%）. However, the doping of Fe^3＋, Mo^6＋, Mn^2＋ and the high doping concentration of Cr^3＋ had no contribution to photocatalytic activity of nitric oxide.

Rare Earth Elements-Doped LiCoO_2 Cathode Material for Lithium-Ion Batteries

Some compounds of LiCo 1- x RE x O 2 (RE=rare earth elements and x =0.01～0.03) were prepared by doping rare earth elements to LiCoO 2 via solid state synthesis. The microstructure characteristics of the LiCo 1- x RE x O 2 were investigated by XRD. It was found that the lattice parameters c are increased and the lattice volumes are enlarged compared to that of LiCoO 2. Moreover, the performance of LiCo 1- x RE x O 2 as the cathode material in lithium ion battery is improved, especially LiCo 1- x Y x O 2 and LiCo 1- x La x O 2. The initial charge/discharge capacities of LiCo 0.99 Y 0.01 O 2 and LiCo 0.99 La 0.01 O 2 are 174/154 (mAh·g -1 ) and 159/149 (mAh·g -1 ) respectively, while those for LiCoO 2 working in the same way are only 139/131 (mAh·g -1 ).

Photocatalytic degradation of Rhodamine B under visible light with Nd-doped titanium dioxide films

Microporous titanium dioxide films were prepared by the sol-gel methods on glass substrates, using tetrabutyl titanate as source material. In order to absorb the visible light and increase the photocatalytic activities, different concentrations of neodymium ions (Nd/Ti molar ratio was 0.5%, 0.7%, 0.9%, and 1.1% respectively) were added into the sol. X-ray diffraction (XRD), X-ray photoelectron spectros-copy (XPS), and atom force microscopy (AFM) were applied to characterize the modified films. A kind of typical textile industry pollutant (Rhodamine B) was used to evaluate the photocatalytic activities of the films under visible light. The results showed that the activities of the films were improved by doping Nd ions into the sol.

Ribbon-like Cu doped V6O13 as Cathode Material for High-performance Lithium Ion Batteries

Ribbon-like Cu doped V6O（13） was synthesized via a simple solvothermal approach followed by heat treatment in air.As an cathode material for lithium ion battery,the ribbon-like Cu doped V6O（13 ）electrode exhibited good capacity retention with a reversible capacity of over 313 m Ah·g^-1 for up to 50 cycles at 0.1C,as well as a high charge capacity of 306 m Ah·g^-1 at a high current rate of 1 C,in comparison to undoped V6O（13 ）electrode（267 m Ah·g^-1 at 0.1C and 273 m Ah·g^-1 at 1 C）.The high rate capability and better cycleability of the doped electrode can be attributed to the influence of the Cu ions on the mophology and the electronic conductivity of V6O（13） during the lithiation and delithiation process.

Nitrogen doping and graphitization tuning coupled hard carbon for superior potassium-ion storage

Hard carbon material is one of the most promising anode materials for potassium ion batteries(PIBs)due to its distinct disordered and non-expandable framework.However,the intrinsically disordered microarchitecture of hard carbon results in low electric conductivity and poor rate capability.Herein,nitrogendoped and partially graphitized hard carbons(NGHCs)derived from commercial coordination compound precursor-ethylenediaminetetraacetic acid(EDTA)disodium cobalt salt hydrate are designed and prepared as high-performance PIBs anode materials.By means of a facile annealing method,nitrogen elements and graphitic domains can be controllably introduced to NGHCs.The resulting NGHCs show structural merits of mesoporous construction,nitrogen doping and homogeneous graphitic domains,which ensures fast kinetics and electron transportation.Applying in anode for PIBs,NGHCs exhibit robust rate capability with high reversible capacity of 298.8 m Ah g^-1 at 50 m A g^-1,and stable cycle stability of 137.6 mAh g^-1 at 500 m A g^-1 after 1000 cycles.Moreover,the ex situ Raman spectra reveal a mixture"adsorption-intercalation mechanism"for potassium storage of NGHCs.More importantly,full PIBs by pairing with perylenetetracarboxylic dianhydride(PTCDA)cathode demonstrate the promising potential of practical application.In terms of commercial precursor,facile synthesis and long cycle lifespan,NGHCs represent a brilliant prospect for practical large-scale applications.

Rare earth doped CaCu_3Ti_4O_(12) electronic ceramics for high frequency applications

Ca1-xRxCu3Ti4O12(R=La,Y,Gd;x=0,0.1,0.2,0.3) electronic ceramics were fabricated by conventional solid-state reaction method.The microstructure and dielectric properties as well as impedance behavior were carefully investigated.XRD results showed that the secondary phases with the general formula R2Ti2O7 existed at grain boundaries of rare earth doped ceramics,which inhibited abnormal grain growth.The dielectric constant decreased from 4×105 in pure CaCu3Ti4O12(CCTO) ceramics to 2×103 with rare earth doping....

Prolonging charge-separation states by doping lanthanide-ions into {001}/{101} facets-coexposed TiO_(2) nanosheets for enhancing photocatalytic H_(2) evolution

Ultrathin TiO_(2)nanosheets with coexposed{001}/{101}facets have attracted considerable attention because of their high photocatalytic activity.However,the charge-separated states in the TiO_(2)nanosheets must be extended to further enhance their photocatalytic activity for H_(2)evolution.Herein,we present a successful attempt to selectively dope lanthanide ions into the{101}facets of ultrathin TiO_(2)nanosheets with coexposed{001}/{101}facets through a facile one-step solvothermal method.The lanthanide doping slightly extended the light-harvesting region and markedly improved the charge-separated states of the TiO_(2)nanosheets as evidenced by UV-vis absorption and steady-state/transient photoluminescence spectra.Upon simulated sunlight irradiation,we observed a 4.2-fold enhancement in the photocatalytic H_(2)evolution activity of optimal Yb^(3+)-doped TiO_(2)nanosheets compared to that of their undoped counterparts.Furthermore,when Pt nanoparticles were used as cocatalysts to reduce the H_(2)overpotential in this system,the photocatalytic activity enhancement factor increased to 8.5.By combining these results with those of control experiments,we confirmed that the extended charge-separated states play the main role in the enhancement of the photocatalytic H_(2)evolution activity of lanthanide-doped TiO_(2)nanosheets with coexposed{001}/{101}facets.

Theoretic and Experimental Studies on Titania Nanotube Doped with Ag Metal Ions

The electronic state density and energy bands of Ag-doped anatase TiO2 are studied by WIEN2k software package based on DFT. The calculation results show that the band-gap of anatase titania became bigger after doping with Ag metal ions. The band-gap transfers from 2.04 to 2.5 eV, but a new energy band appears among the forbidden band after the Ag atom substitution. The interband width of Ag-TiO2 is 0.17 eV, which is located at –0.07 eV; more excitation and jump routes are opened for the electrons. The lowest excitation energy can achieve 1.2 eV, which may allow the photons with lower energy （at longer wavelength, such as visible light） to be absorbed. Ag ions are implanted into the titania nanotube sample by MEVVA （Metal Vapor Vacuum Arc） implanter. The photo-electrochemical response and photo-degradation experiment of titania nanotube samples implanted with Ag ions are tested under UV and visible light; the results indicated that the performance of implanted titania naotubes is enhanced both under UV and visible light; it is worth mentioning that the photocurrent density can reach 0.145 mA/cm2 under visible light, which is 181 times higher than those of pure TiNT, and the k value of degradation methyl orange can obtain 0.30 h-1, which is 71 times higher than that of pure TiNT. All the experimental results are consistent well with the theoretic ones.

Surface modification and characterization of F-Co doped spinel LiMn_2O_4

Spinel LiCo0.09Mn1.91O3.92F0.08 as cathode material was modified with LiCoO2 by the sol-gel method, and the crystal structure, morphology and electrochemical performance were characterized with XRD, SEM, EDS, AAS and charge-discharge test in this paper. The results show that a good clad coated on parent material can be synthesized by the sol-gel method, and the materials with modification have perfect spinel structure. LiCo0.09Mn1.91O3.92F0.08 materials coated by LiCoO2 improve the stability of crystal structure and decrease the dissolution of Mn into electrolyte. With the LiCoO2 content increasing, the specific capacity and cycle performance of samples are improved. The capacity loss is also suppressed distinctly even at 55 ℃.

Synthesis and Characterization of CaF_2 Nanoparticles with Different Doping Concentrations of Er^(3+)

Calcium fluoride nanoparticles with various amounts of erbium ion dopants were prepared by CTAB/C_4 H_9OH/C_7H_(16)/H_2O reverse micro-emulsion method.The nanoparticles were studied by X-ray diffraction(XRD),transmission electron microscopy(TEM),fourier transform infrared spectroscopy(FTIR),absorption and fluorescence spectra.The XRD patterns indicate a typical cubic fluorite structure and no other impurities.TEM results show the synthesized particles having uniform grain size and without agglomeration.FTIR spectra reveal that there are some amounts of-OH,NO_3^-and other organic functional groups on the particle surfaces before the annealing process.Many absorption peaks and bands are present in the absorption spectra,corresponding to the rich energy levels of erbium ion.The Red-Shift of absorption bands and Blue-Shift of fluorescence peaks can be attributed to the weakened energy level split as a result of the decrease in crystal field strength.

Realization of conformal doping on multicrystalline silicon solar cells and black silicon solar cells by plasma immersion ion implantation

Emitted multi-crystalline silicon and black silicon solar cells are conformal doped by ion implantation using the plasma immersion ion implantation （PⅢ） technique. The non-uniformity of emitter doping is lower than 5 %. The secondary ion mass spectrometer profile indicates that the PⅢ technique obtained 100-rim shallow emitter and the emitter depth could be impelled by furnace annealing to 220 nm and 330 nm at 850 ℃ with one and two hours, respectively. Furnace annealing at 850 ℃ could effectively electrically activate the dopants in the silicon. The efficiency of the black silicon solar cell is 14.84% higher than that of the mc-silicon solar cell due to more incident light being absorbed.

Preparation and Properties of Lanthanum Trivalent Ion Doped TiO_2 Nanopowders by Liquid Plasma Spray

The lanthanum trivalent ion doped TiO2 nanopowders were prepared by liquid plasma spray with solution of titanium tetra-tert-butoxide and alcohol as feedstock and La(NO3)3·6H2O as doping component. The photocatalytic activity of samples at different doping concentrations in photocatalytic degradation of methyl orange was discussed. The powders were characterized by Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD), and the effect of doped ion on the pattern, phase composition and crystallite sizes were analyzed. The results indicated that lanthanum trivalent ion doped TiO2 nanopowders could be prepared by liquid plasma spray. Lanthanum trivalent ion doping increased the photocatalytic activity of TiO2 greatly, the optimal doping concentration was 0.5%. The doped powders were the mixture of anatase phase and rutile phase. The contents of anatase phase decreased firstly and then increased with an increase in the contents of lanthanum trivalent ion. Doping lanthanum trivalent ion could make the TiO2 nanopowders uniform and reduced its particle size.

Nitrogen and fluorine co-doped TiO_(2)/carbon microspheres for advanced anodes in sodium-ion batteries: High volumetric capacity, superior power density and large areal capacity

Fast charging and high volumetric capacity are two of the critical demands for sodium-ion batteries(SIBs).Although nanostructured materials achieve outstanding rate performance,they suffer from low tap density and small volumetric capacity.Therefore,how to realize large volumetric capacity and high tap density simultaneously is very challenging.Here,N/F co-doped TiO_(2)/carbon microspheres(NF- TiO_(2)/C)are synthesized to achieve both of them.Theoretical calculations reveal that N and F co-doping increases the contents of oxygen vacancies and narrows the bandgaps of TiO_(2) and C,improving the electronic conductivity of NF- TiO_(2)/C.Furthermore,NF- TiO_(2)/C exhibits the high binding energy and low diffusion energy barrier of Na+,significantly facilitating Na+storage and Na+diffusion.Therefore,NF- TiO_(2)/C offers a high tap density(1.51 g cm^(-3)),an outstanding rate performance(125.9 mAh g^(-1) at 100 C),a large volumetric capacity(190 mAh cm^(-3) at 100 C),a high areal capacity(4.8 mAh cm^(-2))and an ultra-long cycling performance(80.2%after 10,000 cycles at 10 C)simultaneously.In addition,NF- TiO_(2)/C||Na_(3)V_(2)(PO_(4))_(3) full cells achieve an ultrahigh power density of 25.2 kW kg^(-1).These results indicate the great promise of NF- TiO_(2)/C as a high-volumetric-capacity and high-power-density anode material of SIBs.

Reduced graphene oxide doping flower-like Fe_(7)S_(8) nanosheets for high performance potassium ion storage

Finding easy-to-operate strategy to obtain anode material with well-designed structure and excellent electrochemical performance is necessary to promote the development of the future potassium-ion batteries(PIBs).In this work,we synthesized reduced graphene oxide doping flower-like Fe_(7)S_(8) nanosheets electrode materials using one-step hydrothermal strategy.The rGO@Fe_(7)S_(8) composite is composed of homogeneous Fe_(7)S_(8) and reduced graphene oxide thin nanosheets.This unique structure not only promotes the penetration of electrolyte and increases the conductive of the pure Fe_(7)S_(8) electrode materials,but also relieves the volume expansion of K^(+) during charge/discharge process.When applied this interesting anode electrode for PIBs,the rGO@Fe_(7)S_(8) exhibits excellent electrochemical performance.It delivers a high reversible specific capacity of 445 mAh g^(-1) at 50 mA g^(-1),excellent rate performance(284 mAhg^(-1)at 500 mA g^(-1) and 237 mAh g^(-1) at 1000 mA g^(-1)),and a high cycling stability at 100 mA g^(-1)(maintained 355 mAh g^(-1) after 300 cycles).