Due to its low cost and natural abundance of sodium,Na-ion batteries(NIBs)are promising candidates for large-scale energy storage systems.The development of ultralow voltage anode materials is of great significance in...Due to its low cost and natural abundance of sodium,Na-ion batteries(NIBs)are promising candidates for large-scale energy storage systems.The development of ultralow voltage anode materials is of great significance in improving the energy density of NIBs.Low-voltage anode materials,however,are severely lacking in NIBs.Of all the reported insertion oxides anodes,the Na_(2)Ti_(3)O_(7) has the lowest operating voltage(an average potential of 0.3 V vs.Na^(+)/Na)and is less likely to deposit sodium,which has excellent potential for achieving NIBs with high energy densities and high safety.Although significant progress has been made,achieving Na_(2)Ti_(3)O_(7) electrodes with excellent performance remains a severe challenge.This paper systematically summarizes and discusses the physicochemical properties and synthesis methods of Na_(2)Ti_(3)O_(7).Then,the sodium storage mechanisms,key issues and challenges,and the optimization strategies for the electrochemical performance of Na_(2)Ti_(3)O_(7) are classified and further elaborated.Finally,remaining challenges and future research directions on the Na_(2)Ti_(3)O_(7) anode are highlighted.This review offers insights into the design of high-energy and high-safety NIBs.展开更多
The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Th...The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Therefore,this paper assesses the performance of a 51 kW PV solar power plant connected to a low-voltage grid to feed an administrative building in the 6th of October City,Egypt.The performance analysis of the considered grid-connected PV system is carried out using power system simulator for Engineering(PSS/E)software.Where the PSS/E program,monitors and uses the power analyzer that displays the parameters and measures some parameters such as current,voltage,total power,power factor,frequency,and current and voltage harmonics,the used inverter from the type of grid inverter for the considered system.The results conclude that when the maximum solar radiation is reached,the maximum current can be obtained from the solar panels,thus obtaining the maximum power and power factor.Decreasing total voltage harmonic distortion,a current harmonic distortion within permissible limits using active harmonic distortion because this type is fast in processing up to 300 microseconds.The connection between solar stations and the national grid makes the system more efficient.展开更多
The increasing proportion of distributed photovoltaics(DPVs)and electric vehicle charging stations in low-voltage distribution networks(LVDNs)has resulted in challenges such as distribution transformer overloads and v...The increasing proportion of distributed photovoltaics(DPVs)and electric vehicle charging stations in low-voltage distribution networks(LVDNs)has resulted in challenges such as distribution transformer overloads and voltage violations.To address these problems,we propose a coordinated planning method for flexible interconnections and energy storage systems(ESSs)to improve the accommodation capacity of DPVs.First,the power-transfer characteristics of flexible interconnection and ESSs are analyzed.The equipment costs of the voltage source converters(VSCs)and ESSs are also analyzed comprehensively,considering the differences in installation and maintenance costs for different installation locations.Second,a bilevel programming model is established to minimize the annual comprehensive cost and yearly total PV curtailment capacity.Within this framework,the upper-level model optimizes the installation locations and capacities of the VSCs and ESSs,whereas the lower-level model optimizes the operating power of the VSCs and ESSs.The proposed model is solved using a non-dominated sorting genetic algorithm with an elite strategy(NSGA-II).The effectiveness of the proposed planning method is validated through an actual LVDN scenario,which demonstrates its advantages in enhancing PV accommodation capacity.In addition,the economic benefits of various planning schemes with different flexible interconnection topologies and different PV grid-connected forms are quantitatively analyzed,demonstrating the adaptability of the proposed coordinated planning method.展开更多
A novel structure of low-voltage trigger silicon-controlled rectifiers(LVTSCRs) with low trigger voltage and high holding voltage is proposed for electrostatic discharge(ESD) protection. The proposed ESD protection de...A novel structure of low-voltage trigger silicon-controlled rectifiers(LVTSCRs) with low trigger voltage and high holding voltage is proposed for electrostatic discharge(ESD) protection. The proposed ESD protection device possesses an ESD implant and a floating structure. This improvement enhances the current discharge capability of the gate-grounded NMOS and weakens the current gain of the silicon-controlled rectifier current path. According to the simulation results, the proposed device retains a low trigger voltage characteristic of LVTSCRs and simultaneously increases the holding voltage to 5.53 V, providing an effective way to meet the ESD protection requirement of the 5 V CMOS process.展开更多
The use of entomopathogenic fungi (EF) in recent years has been highly effective against the different orders of insects considered pests of agricultural importance and their conidia have been commonly applied, but it...The use of entomopathogenic fungi (EF) in recent years has been highly effective against the different orders of insects considered pests of agricultural importance and their conidia have been commonly applied, but it has been reported that these are sensitive to the environmental conditions. For this reason, biopesticides products have been formulated based on secondary metabolites, recently. These biomolecules participate as biological control agent, such as: cyclic depsipeptides, amino acids, polyketides, polyphenols and terpenoids, affecting their morphology, life cycle and insect behavior. The use of secondary metabolites of entomopathogenic fungi opens the possibility of application in a more efficient way for the control of agricultural pests in a compatible with the environment and human health;therefore, it is important to know, analyzing the type of molecules, their effects, and their different methods of application.展开更多
Many phytochemicals and their derived metabolites produced by plants are extensively employed in commercial goods,pharmaceutical products as well as in the environmental and medicalfields.However,these secondary metabo...Many phytochemicals and their derived metabolites produced by plants are extensively employed in commercial goods,pharmaceutical products as well as in the environmental and medicalfields.However,these secondary metabolites obtained from plants are in low amounts,and it is difficult to synthesize them at the industrial level.Despite these challenges,they may be utilized for a variety of medicinal products that are either available in the market or are being researched and tested.Secondary metabolites are complex compounds that exhibit chirality.Further,under controlled conditions with elicitors,desired secondary metabolites may be produced from plant cell cultures.This review emphasizes the various aspects of secondary metabolites including their types,synthesis,and applications as medicinal products.The article aims to promote the use of plant secondary metabolites in the management and treatment of various diseases.展开更多
This study investigated the effects of upper-level descending inflow(ULDI)associated with inner-eyewall convection on the formation of the moat in tropical cyclones(TCs)with secondary eyewall formation(SEF).In our num...This study investigated the effects of upper-level descending inflow(ULDI)associated with inner-eyewall convection on the formation of the moat in tropical cyclones(TCs)with secondary eyewall formation(SEF).In our numerical experiments,a clear moat with SEF occurred in TCs with a significant ULDI,while no SEF occurred in TCs without a significant ULDI.The eyewall convection developed more vigorously in the control run.A ULDI occurred outside the inner-eyewall convection,where it was symmetrically unstable.The ULDI was initially triggered by the diabatic warming released by the inner eyewall and later enhanced by the cooling below the anvil cloud.The ULDI penetrated the outer edge of the inner eyewall with relatively dry air and prevented excessive solid-phase hydrometeors from being advected further outward.It produced extensive sublimation cooling of falling hydrometeors between the eyewall and the outer convection.The sublimation cooling resulted in negative buoyancy and further induced strong subsidence between the eyewall and the outer convection.As a result,a clear moat was generated.Development of the moat in the ongoing SEF prevented the outer rainband from moving farther inward,helping the outer rainband to symmetrize into an outer eyewall.In the sensitivity experiment,no significant ULDI formed since the eyewall convection was weaker,and the eyewall anvil developed relatively lower,meaning the formation of a moat and thus an outer eyewall was less likely.This study suggests that a better-represented simulation of inner-eyewall convective structures and distribution of the solid-phase hydrometeors is important to the prediction of SEF.展开更多
The initial shape of the secondary arc considerably influences its subsequent shape.To establish the model for the arcing time of the secondary arc and modify the single-phase reclosing sequence,theoretical and experi...The initial shape of the secondary arc considerably influences its subsequent shape.To establish the model for the arcing time of the secondary arc and modify the single-phase reclosing sequence,theoretical and experimental analysis of the evolution process of the short-circuit arc to the secondary arc is critical.In this study,an improved charge simulation method was used to develop the internal-space electric-field model of the short-circuit arc.The intensity of the electric field was used as an independent variable to describe the initial shape of the secondary arc.A secondary arc evolution model was developed based on this model.Moreover,the accuracy of the model was evaluated by comparison with physical experimental results.When the secondary arc current increased,the arcing time and dispersion increased.There is an overall trend of increasing arc length with increasing arcing time.Nevertheless,there is a reduction in arc length during arc ignition due to short circuits between the arc columns.Furthermore,the arcing time decreased in the range of 0°-90°as the angle between the wind direction and the x-axis increased.This work investigated the method by which short-circuit arcs evolve into secondary arcs.The results can be used to develop the secondary arc evolution model and to provide both a technical and theoretical basis for secondary arc suppression.展开更多
Due to a complex geological and biotic history,the Isthmus of Tehuantepec(IT),has been long recognized as a driver for the evolutionary divergence of numerous lowland and highland taxa.Widely distributed in the lowlan...Due to a complex geological and biotic history,the Isthmus of Tehuantepec(IT),has been long recognized as a driver for the evolutionary divergence of numerous lowland and highland taxa.Widely distributed in the lowlands of the American continent,the White-Tipped Dove(Leptotila verreauxi)is a polytypic species with 13 recognized subspecies.Four of these have been recorded in Mexico,and the distribution of three abuts at the IT,suggesting a contact zone.To estimate phylogenetic patterns,divergence times and genetic differentiation,we examined two mt DNA(ND2 and COI)and one n DNA(β-fibint 7)markers.We also used correlative ecological niche models(ENM)to assess whether ecological differences across the IT may have acted as a biogeographical boundary.We estimated paleodistributions during the Middle Holocene,Last Glacial Maximum and Last Interglacial,to evaluate the influence of climate changes on the distribution and demographic changes.Our results showed genetically distinct lineages that diverged approximately 2.5 million years ago.Climatic and ecological factors may have played a dual role in promoting differentiation,but also in the formation of a secondary contact zone in the southern IT.Our ecological niche comparisons indicated that the ecological niche of sympatric lineages at the IT are not identical,suggesting niches divergence;in addition,environmental niche models across the region indicated no abrupt biogeographic barriers,but the presence of regions with low suitability.These results suggest that genetic differentiation originated by a vicariant event probably related to environmental factors,favored the evolution of different ecological niches.Also,the absence of a biogeographic barrier but the presence of less suitable areas in the contact regions,suggest that secondary contact zones may be also maintained by climatic factors for the eastern group,but also by biotic interactions for the western group.展开更多
DC-DC converter-based multi-bus DC microgrids(MGs) in series have received much attention, where the conflict between voltage recovery and current balancing has been a hot topic. The lack of models that accurately por...DC-DC converter-based multi-bus DC microgrids(MGs) in series have received much attention, where the conflict between voltage recovery and current balancing has been a hot topic. The lack of models that accurately portray the electrical characteristics of actual MGs while is controller design-friendly has kept the issue active. To this end, this paper establishes a large-signal model containing the comprehensive dynamical behavior of the DC MGs based on the theory of high-order fully actuated systems, and proposes distributed optimal control based on this. The proposed secondary control method can achieve the two goals of voltage recovery and current sharing for multi-bus DC MGs. Additionally, the simple structure of the proposed approach is similar to one based on droop control, which allows this control technique to be easily implemented in a variety of modern microgrids with different configurations. In contrast to existing studies, the process of controller design in this paper is closely tied to the actual dynamics of the MGs. It is a prominent feature that enables engineers to customize the performance metrics of the system. In addition, the analysis of the stability of the closed-loop DC microgrid system, as well as the optimality and consensus of current sharing are given. Finally, a scaled-down solar and battery-based microgrid prototype with maximum power point tracking controller is developed in the laboratory to experimentally test the efficacy of the proposed control method.展开更多
With the continuous promotion of the construction of child friendly cities,the school commuting space is an important component of the construction of child friendly roads.Based on the background of child friendly cit...With the continuous promotion of the construction of child friendly cities,the school commuting space is an important component of the construction of child friendly roads.Based on the background of child friendly cities,the commuting space of 11 primary and secondary schools in Bajiao Street is analyzed through literature analysis and field research methods.Firstly,the relevant literature on school commuting space is sorted out,and the characteristics of school commuting space are summarized,including transportation,landscape,culture,leisure,and security.Secondly,the characteristics of commuting space of primary and secondary schools in Bajiao Street are analyzed from three aspects:in front of the school gate,path space,and node space.This paper aims to provide reference and guidance for the future construction of children’s walking school commuting and promote the construction of a child friendly city.展开更多
BACKGROUND As research on diabetes continues to advance,more complex classifications of this disease have emerged,revealing the existence of special types of diabetes,and many of these patients are prone to misdiagnos...BACKGROUND As research on diabetes continues to advance,more complex classifications of this disease have emerged,revealing the existence of special types of diabetes,and many of these patients are prone to misdiagnosis and underdiagnosis,leading to treatment delays and increased health care costs.The purpose of this study was to identify four causes of secondary diabetes.CASE SUMMARY Secondary diabetes can be caused by various factors,some of which are often overlooked.These factors include genetic defects,autoimmune disorders,and diabetes induced by tumours.This paper describes four types of secondary diabetes caused by Williams–Beuren syndrome,Prader–Willi syndrome,pituitary adenoma,and IgG4-related diseases.These cases deviate significantly from the typical progression of the disease due to their low incidence and rarity,often leading to their neglect in clinical practice.In comparison to regular diabetes patients,the four individuals described here exhibited distinct characteristics.Standard hypoglycaemic treatments failed to effectively control the disease.Subsequently,a series of examinations and follow-up history confirmed the diagnosis and underlying cause of diabetes.Upon addressing the primary condition,such as excising a pituitary adenoma,providing glucocorticoid supplementation,and implementing symptomatic treatments,all patients experienced a considerable decrease in blood glucose levels,which were subsequently maintained within a stable range.Furthermore,other accompanying symptoms improved.CONCLUSION Rare diseases causing secondary diabetes are often not considered in the diag-nosis of diabetes.Therefore,it is crucial to conduct genetic tests,antibody detection and other appropriate diagnostic measures when necessary to facilitate early diagnosis and intervention through proactive and efficient management of the underlying condition,ultimately improving patient outcomes.展开更多
The global obesity pandemic has resulted in a rise in the prevalence of male obesity-related secondary hypogonadism(MOSH)with emerging evidence on the role of testosterone therapy.We aim to provide an updated and prac...The global obesity pandemic has resulted in a rise in the prevalence of male obesity-related secondary hypogonadism(MOSH)with emerging evidence on the role of testosterone therapy.We aim to provide an updated and practical approach towards its management.We did a comprehensive literature search across MEDLINE(via PubMed),Scopus,and Google Scholar databases using the keywords“MOSH”OR“Obesity-related hypogonadism”OR“Testosterone replacement therapy”OR“Selective estrogen receptor modulator”OR“SERM”OR“Guidelines on male hypogonadism”as well as a manual search of references within the articles.A narrative review based on available evidence,recommendations and their practical implications was done.Although weight loss is the ideal therapeutic strategy for patients with MOSH,achievement of significant weight reduction is usually difficult with lifestyle changes alone in real-world practice.Therefore,androgen administration is often necessary in the management of hypogonadism in patients with MOSH which also improves many other comorbidities related to obesity.However,there is conflicting evidence for the appropriate use of testosterone replacement therapy(TRT),and it can also be associated with complications.This evidence-based review updates the available evidence including the very recently published results of the TRAVERSE trial and provides comprehensive clinical practice pearls for the management of patients with MOSH.Before starting testosterone replacement in functional hypogonadism of obesity,it would be desirable to initiate lifestyle modification to ensure weight reduction.TRT should be coupled with the management of other comorbidities related to obesity in MOSH patients.Balancing the risks and benefits of TRT should be considered in every patient before and during longterm management.展开更多
With the rapid development of electrical power systems,ensuring the accuracy and reliability of power transmis-sion has become particularly crucial.The secondary cable line calibrator for current transformers(CT)plays...With the rapid development of electrical power systems,ensuring the accuracy and reliability of power transmis-sion has become particularly crucial.The secondary cable line calibrator for current transformers(CT)plays an essential role in calibrating electrical power systems.It is not only related to the safe operation of the system but also directly im-pacts the accuracy of energy metering.This study aims to design and analyze an efficient CT secondary cable line calibra-tor to explore its application effects in the power system.By thoroughly analyzing the characteristics of CT secondary ca-ble lines and the design requirements of the calibrator,this paper proposes an innovative design scheme for the calibrator.This device demonstrates significant effects in enhancing the accuracy and stability of power system calibration,providing robust technical support for the optimization and upgrade of the power system.This research not only offers a theoretical basis and practical guidance for the design and application of CT secondary cable line calibrators but also contributes new ideas and methods for the precise calibration and efficient management of the power system.展开更多
With the rapid development of urban economy, distribution network construction of city is lagging behind the increment of load, and low-voltage problem has become the main complaints of the power users. Based on Pytho...With the rapid development of urban economy, distribution network construction of city is lagging behind the increment of load, and low-voltage problem has become the main complaints of the power users. Based on Python [1] scripting language, this paper develops a piece of software which can provide a friendly human-machine experience for the user, calculate the voltage of the power distribution area and propose corresponding control measures, then the paper takes the actual power distribution area to verify its effectiveness.展开更多
Scaling problems and limitations of conventional silicon transistors have led the designers to exploit novel nano-technologies. One of the most promising and feasible nano-technologies is CNT(Carbon Nanotube) based tr...Scaling problems and limitations of conventional silicon transistors have led the designers to exploit novel nano-technologies. One of the most promising and feasible nano-technologies is CNT(Carbon Nanotube) based transistors. In this paper, a high-speed and energy-efficient CNFET(Carbon Nanotube Field Effect Transistor) based Full Adder cell is proposed for nanotechnology. This design is simulated in various supply voltages, frequencies and load capacitors using HSPICE circuit simulator. Significant improvement is achieved in terms of speed and PDP(Power-Delay-Product) in comparison with other classical and state-of-the-art CMOS and CNFET-based designs, existing in the literature. The proposed Full Adder can also drive large load capacitance and works properly in low supply voltages.展开更多
Powder metallurgy is an efficient approach to fabricate varieties of high performance structure materials, function materials and special materials working under limited conditions. Research and development of new eff...Powder metallurgy is an efficient approach to fabricate varieties of high performance structure materials, function materials and special materials working under limited conditions. Research and development of new efficient technology to form high-density, high-performance and net shape parts is a key to widen application and development of powder materials. Recently, the low-voltage electromagnetic compaction (EMC) has been used by present authors to compacted copper, tin, aluminum powders and the products with 99% relative density have been acquired. In this work, the research has been extended to investigation on the density uniformity of pressed parts. The analysis results show that the density of the part compacted by low-voltage EMC decreases gradually in press direction as static compaction. But it is higher and more homogeneous. The density of the top part increases gradually from the center to the outer, which is just reversal of the bottom part. In some extent, the higher the discharging voltage is, the higher the density is and the more homogeneous the distribution is. In addition, repetitive compaction can improve the density of powder parts and the distribution uniformity.展开更多
Low-voltage electromagnetic compaction (EMC) was used to compact metal powders (Cu) and ceramic powders (TiO2) in the indirect way. It was found that the density of the metal powder parts compacted by low-voltag...Low-voltage electromagnetic compaction (EMC) was used to compact metal powders (Cu) and ceramic powders (TiO2) in the indirect way. It was found that the density of the metal powder parts compacted by low-voltage EMC varied linearly with the discharging voltage in the range investigated. But for ceramic powders, the discharging voltage has an optimal value. Under the value, the density increases as discharging voltage rises, but beyond the value the trend is reverse. The experimental results show that the density of the metal parts decreases gradually along press direction. And the density of the ceramic parts decreases with the advancement of the aspect ratio h/d (height/diameter). In addition, repetitive compaction can improve the density of both metal and ceramic parts and reduce the effects of aspect ratio on the density.展开更多
This paper is devoted to the simulation of the arc plasma in a simplified low-voltage circuit breaker chamber. Based on a group of coupled governing equations, a three-dimensional (3-D) arc plasma model is built and...This paper is devoted to the simulation of the arc plasma in a simplified low-voltage circuit breaker chamber. Based on a group of coupled governing equations, a three-dimensional (3-D) arc plasma model is built and solved by a modified commercial code. Firstly, this paper presents a solution of the stationary state of the arc plasma and discusses the distribution of some parameters throughout the chamber. Secondly, with the ferromagnetic materials included, the balance of the stationary state is broken and a transient course is calculated. In light of the simulation results, the temperature distribution sequence, the arc motion and the plasma jet are then described and analyzed in detail.展开更多
Low-voltage distribution systems in our country are mostly used in agricultural loads and household loads. The value and using time of these kinds of loads are uncontrollable, which lead to the three-phase imbalance i...Low-voltage distribution systems in our country are mostly used in agricultural loads and household loads. The value and using time of these kinds of loads are uncontrollable, which lead to the three-phase imbalance in low-voltage distribution system, and seriously affect the quality of power supply. A new type of the commutation system and an improved quantum genetic algorithm (IQGA) are proposed in the paper. At last, the rationality and the efficiency of the method are verified by a practical example.展开更多
基金supported by the National Natural Science Foundation of China (52307239,52102300,52207234)the Natural Science Foundation of Hubei Province (2022CFB1003,2021CFA025)。
文摘Due to its low cost and natural abundance of sodium,Na-ion batteries(NIBs)are promising candidates for large-scale energy storage systems.The development of ultralow voltage anode materials is of great significance in improving the energy density of NIBs.Low-voltage anode materials,however,are severely lacking in NIBs.Of all the reported insertion oxides anodes,the Na_(2)Ti_(3)O_(7) has the lowest operating voltage(an average potential of 0.3 V vs.Na^(+)/Na)and is less likely to deposit sodium,which has excellent potential for achieving NIBs with high energy densities and high safety.Although significant progress has been made,achieving Na_(2)Ti_(3)O_(7) electrodes with excellent performance remains a severe challenge.This paper systematically summarizes and discusses the physicochemical properties and synthesis methods of Na_(2)Ti_(3)O_(7).Then,the sodium storage mechanisms,key issues and challenges,and the optimization strategies for the electrochemical performance of Na_(2)Ti_(3)O_(7) are classified and further elaborated.Finally,remaining challenges and future research directions on the Na_(2)Ti_(3)O_(7) anode are highlighted.This review offers insights into the design of high-energy and high-safety NIBs.
文摘The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Therefore,this paper assesses the performance of a 51 kW PV solar power plant connected to a low-voltage grid to feed an administrative building in the 6th of October City,Egypt.The performance analysis of the considered grid-connected PV system is carried out using power system simulator for Engineering(PSS/E)software.Where the PSS/E program,monitors and uses the power analyzer that displays the parameters and measures some parameters such as current,voltage,total power,power factor,frequency,and current and voltage harmonics,the used inverter from the type of grid inverter for the considered system.The results conclude that when the maximum solar radiation is reached,the maximum current can be obtained from the solar panels,thus obtaining the maximum power and power factor.Decreasing total voltage harmonic distortion,a current harmonic distortion within permissible limits using active harmonic distortion because this type is fast in processing up to 300 microseconds.The connection between solar stations and the national grid makes the system more efficient.
基金supported by the Science and Technology Support Program of Guizhou Province([2022]General 012)the Key Science and Technology Project of China Southern Power Grid Corporation(GZKJXM20220043)。
文摘The increasing proportion of distributed photovoltaics(DPVs)and electric vehicle charging stations in low-voltage distribution networks(LVDNs)has resulted in challenges such as distribution transformer overloads and voltage violations.To address these problems,we propose a coordinated planning method for flexible interconnections and energy storage systems(ESSs)to improve the accommodation capacity of DPVs.First,the power-transfer characteristics of flexible interconnection and ESSs are analyzed.The equipment costs of the voltage source converters(VSCs)and ESSs are also analyzed comprehensively,considering the differences in installation and maintenance costs for different installation locations.Second,a bilevel programming model is established to minimize the annual comprehensive cost and yearly total PV curtailment capacity.Within this framework,the upper-level model optimizes the installation locations and capacities of the VSCs and ESSs,whereas the lower-level model optimizes the operating power of the VSCs and ESSs.The proposed model is solved using a non-dominated sorting genetic algorithm with an elite strategy(NSGA-II).The effectiveness of the proposed planning method is validated through an actual LVDN scenario,which demonstrates its advantages in enhancing PV accommodation capacity.In addition,the economic benefits of various planning schemes with different flexible interconnection topologies and different PV grid-connected forms are quantitatively analyzed,demonstrating the adaptability of the proposed coordinated planning method.
基金supported by the National Natural Science Foundation of China (Grant No. 61904110)。
文摘A novel structure of low-voltage trigger silicon-controlled rectifiers(LVTSCRs) with low trigger voltage and high holding voltage is proposed for electrostatic discharge(ESD) protection. The proposed ESD protection device possesses an ESD implant and a floating structure. This improvement enhances the current discharge capability of the gate-grounded NMOS and weakens the current gain of the silicon-controlled rectifier current path. According to the simulation results, the proposed device retains a low trigger voltage characteristic of LVTSCRs and simultaneously increases the holding voltage to 5.53 V, providing an effective way to meet the ESD protection requirement of the 5 V CMOS process.
文摘The use of entomopathogenic fungi (EF) in recent years has been highly effective against the different orders of insects considered pests of agricultural importance and their conidia have been commonly applied, but it has been reported that these are sensitive to the environmental conditions. For this reason, biopesticides products have been formulated based on secondary metabolites, recently. These biomolecules participate as biological control agent, such as: cyclic depsipeptides, amino acids, polyketides, polyphenols and terpenoids, affecting their morphology, life cycle and insect behavior. The use of secondary metabolites of entomopathogenic fungi opens the possibility of application in a more efficient way for the control of agricultural pests in a compatible with the environment and human health;therefore, it is important to know, analyzing the type of molecules, their effects, and their different methods of application.
文摘Many phytochemicals and their derived metabolites produced by plants are extensively employed in commercial goods,pharmaceutical products as well as in the environmental and medicalfields.However,these secondary metabolites obtained from plants are in low amounts,and it is difficult to synthesize them at the industrial level.Despite these challenges,they may be utilized for a variety of medicinal products that are either available in the market or are being researched and tested.Secondary metabolites are complex compounds that exhibit chirality.Further,under controlled conditions with elicitors,desired secondary metabolites may be produced from plant cell cultures.This review emphasizes the various aspects of secondary metabolites including their types,synthesis,and applications as medicinal products.The article aims to promote the use of plant secondary metabolites in the management and treatment of various diseases.
基金supported by the National Natural Science Foundation of China(Grant Nos.42192552,42192551,42150710531,42175016,and 42075072)the Shanghai Typhoon Research Fund(Grant No.TFJJ202207)the Basic Research Fund of CAMS(Grant No.2023Y010)。
文摘This study investigated the effects of upper-level descending inflow(ULDI)associated with inner-eyewall convection on the formation of the moat in tropical cyclones(TCs)with secondary eyewall formation(SEF).In our numerical experiments,a clear moat with SEF occurred in TCs with a significant ULDI,while no SEF occurred in TCs without a significant ULDI.The eyewall convection developed more vigorously in the control run.A ULDI occurred outside the inner-eyewall convection,where it was symmetrically unstable.The ULDI was initially triggered by the diabatic warming released by the inner eyewall and later enhanced by the cooling below the anvil cloud.The ULDI penetrated the outer edge of the inner eyewall with relatively dry air and prevented excessive solid-phase hydrometeors from being advected further outward.It produced extensive sublimation cooling of falling hydrometeors between the eyewall and the outer convection.The sublimation cooling resulted in negative buoyancy and further induced strong subsidence between the eyewall and the outer convection.As a result,a clear moat was generated.Development of the moat in the ongoing SEF prevented the outer rainband from moving farther inward,helping the outer rainband to symmetrize into an outer eyewall.In the sensitivity experiment,no significant ULDI formed since the eyewall convection was weaker,and the eyewall anvil developed relatively lower,meaning the formation of a moat and thus an outer eyewall was less likely.This study suggests that a better-represented simulation of inner-eyewall convective structures and distribution of the solid-phase hydrometeors is important to the prediction of SEF.
基金supported by National Natural Science Foundation of China(Nos.92066108 and 51277061)。
文摘The initial shape of the secondary arc considerably influences its subsequent shape.To establish the model for the arcing time of the secondary arc and modify the single-phase reclosing sequence,theoretical and experimental analysis of the evolution process of the short-circuit arc to the secondary arc is critical.In this study,an improved charge simulation method was used to develop the internal-space electric-field model of the short-circuit arc.The intensity of the electric field was used as an independent variable to describe the initial shape of the secondary arc.A secondary arc evolution model was developed based on this model.Moreover,the accuracy of the model was evaluated by comparison with physical experimental results.When the secondary arc current increased,the arcing time and dispersion increased.There is an overall trend of increasing arc length with increasing arcing time.Nevertheless,there is a reduction in arc length during arc ignition due to short circuits between the arc columns.Furthermore,the arcing time decreased in the range of 0°-90°as the angle between the wind direction and the x-axis increased.This work investigated the method by which short-circuit arcs evolve into secondary arcs.The results can be used to develop the secondary arc evolution model and to provide both a technical and theoretical basis for secondary arc suppression.
基金the financial support for this study by PAPIIT-UNAM grant(IN222817)to LAS-Gthe Fran?ois Vuilleumier Fund for Neotropical Bird Research from the Neotropical Ornithological Society(NOS)awarded to OJE-C。
文摘Due to a complex geological and biotic history,the Isthmus of Tehuantepec(IT),has been long recognized as a driver for the evolutionary divergence of numerous lowland and highland taxa.Widely distributed in the lowlands of the American continent,the White-Tipped Dove(Leptotila verreauxi)is a polytypic species with 13 recognized subspecies.Four of these have been recorded in Mexico,and the distribution of three abuts at the IT,suggesting a contact zone.To estimate phylogenetic patterns,divergence times and genetic differentiation,we examined two mt DNA(ND2 and COI)and one n DNA(β-fibint 7)markers.We also used correlative ecological niche models(ENM)to assess whether ecological differences across the IT may have acted as a biogeographical boundary.We estimated paleodistributions during the Middle Holocene,Last Glacial Maximum and Last Interglacial,to evaluate the influence of climate changes on the distribution and demographic changes.Our results showed genetically distinct lineages that diverged approximately 2.5 million years ago.Climatic and ecological factors may have played a dual role in promoting differentiation,but also in the formation of a secondary contact zone in the southern IT.Our ecological niche comparisons indicated that the ecological niche of sympatric lineages at the IT are not identical,suggesting niches divergence;in addition,environmental niche models across the region indicated no abrupt biogeographic barriers,but the presence of regions with low suitability.These results suggest that genetic differentiation originated by a vicariant event probably related to environmental factors,favored the evolution of different ecological niches.Also,the absence of a biogeographic barrier but the presence of less suitable areas in the contact regions,suggest that secondary contact zones may be also maintained by climatic factors for the eastern group,but also by biotic interactions for the western group.
基金supported in part by the National Natural Science Foundation of China(62173255, 62188101)Shenzhen Key Laboratory of Control Theory and Intelligent Systems,(ZDSYS20220330161800001)。
文摘DC-DC converter-based multi-bus DC microgrids(MGs) in series have received much attention, where the conflict between voltage recovery and current balancing has been a hot topic. The lack of models that accurately portray the electrical characteristics of actual MGs while is controller design-friendly has kept the issue active. To this end, this paper establishes a large-signal model containing the comprehensive dynamical behavior of the DC MGs based on the theory of high-order fully actuated systems, and proposes distributed optimal control based on this. The proposed secondary control method can achieve the two goals of voltage recovery and current sharing for multi-bus DC MGs. Additionally, the simple structure of the proposed approach is similar to one based on droop control, which allows this control technique to be easily implemented in a variety of modern microgrids with different configurations. In contrast to existing studies, the process of controller design in this paper is closely tied to the actual dynamics of the MGs. It is a prominent feature that enables engineers to customize the performance metrics of the system. In addition, the analysis of the stability of the closed-loop DC microgrid system, as well as the optimality and consensus of current sharing are given. Finally, a scaled-down solar and battery-based microgrid prototype with maximum power point tracking controller is developed in the laboratory to experimentally test the efficacy of the proposed control method.
基金National Natural Science Foundation of China(51708004)Beijing Youth Teaching Elite Team Construction Project(108051360023XN261)North China University of Technology Yuyou Talent Training Program(215051360020XN160/009).
文摘With the continuous promotion of the construction of child friendly cities,the school commuting space is an important component of the construction of child friendly roads.Based on the background of child friendly cities,the commuting space of 11 primary and secondary schools in Bajiao Street is analyzed through literature analysis and field research methods.Firstly,the relevant literature on school commuting space is sorted out,and the characteristics of school commuting space are summarized,including transportation,landscape,culture,leisure,and security.Secondly,the characteristics of commuting space of primary and secondary schools in Bajiao Street are analyzed from three aspects:in front of the school gate,path space,and node space.This paper aims to provide reference and guidance for the future construction of children’s walking school commuting and promote the construction of a child friendly city.
文摘BACKGROUND As research on diabetes continues to advance,more complex classifications of this disease have emerged,revealing the existence of special types of diabetes,and many of these patients are prone to misdiagnosis and underdiagnosis,leading to treatment delays and increased health care costs.The purpose of this study was to identify four causes of secondary diabetes.CASE SUMMARY Secondary diabetes can be caused by various factors,some of which are often overlooked.These factors include genetic defects,autoimmune disorders,and diabetes induced by tumours.This paper describes four types of secondary diabetes caused by Williams–Beuren syndrome,Prader–Willi syndrome,pituitary adenoma,and IgG4-related diseases.These cases deviate significantly from the typical progression of the disease due to their low incidence and rarity,often leading to their neglect in clinical practice.In comparison to regular diabetes patients,the four individuals described here exhibited distinct characteristics.Standard hypoglycaemic treatments failed to effectively control the disease.Subsequently,a series of examinations and follow-up history confirmed the diagnosis and underlying cause of diabetes.Upon addressing the primary condition,such as excising a pituitary adenoma,providing glucocorticoid supplementation,and implementing symptomatic treatments,all patients experienced a considerable decrease in blood glucose levels,which were subsequently maintained within a stable range.Furthermore,other accompanying symptoms improved.CONCLUSION Rare diseases causing secondary diabetes are often not considered in the diag-nosis of diabetes.Therefore,it is crucial to conduct genetic tests,antibody detection and other appropriate diagnostic measures when necessary to facilitate early diagnosis and intervention through proactive and efficient management of the underlying condition,ultimately improving patient outcomes.
文摘The global obesity pandemic has resulted in a rise in the prevalence of male obesity-related secondary hypogonadism(MOSH)with emerging evidence on the role of testosterone therapy.We aim to provide an updated and practical approach towards its management.We did a comprehensive literature search across MEDLINE(via PubMed),Scopus,and Google Scholar databases using the keywords“MOSH”OR“Obesity-related hypogonadism”OR“Testosterone replacement therapy”OR“Selective estrogen receptor modulator”OR“SERM”OR“Guidelines on male hypogonadism”as well as a manual search of references within the articles.A narrative review based on available evidence,recommendations and their practical implications was done.Although weight loss is the ideal therapeutic strategy for patients with MOSH,achievement of significant weight reduction is usually difficult with lifestyle changes alone in real-world practice.Therefore,androgen administration is often necessary in the management of hypogonadism in patients with MOSH which also improves many other comorbidities related to obesity.However,there is conflicting evidence for the appropriate use of testosterone replacement therapy(TRT),and it can also be associated with complications.This evidence-based review updates the available evidence including the very recently published results of the TRAVERSE trial and provides comprehensive clinical practice pearls for the management of patients with MOSH.Before starting testosterone replacement in functional hypogonadism of obesity,it would be desirable to initiate lifestyle modification to ensure weight reduction.TRT should be coupled with the management of other comorbidities related to obesity in MOSH patients.Balancing the risks and benefits of TRT should be considered in every patient before and during longterm management.
文摘With the rapid development of electrical power systems,ensuring the accuracy and reliability of power transmis-sion has become particularly crucial.The secondary cable line calibrator for current transformers(CT)plays an essential role in calibrating electrical power systems.It is not only related to the safe operation of the system but also directly im-pacts the accuracy of energy metering.This study aims to design and analyze an efficient CT secondary cable line calibra-tor to explore its application effects in the power system.By thoroughly analyzing the characteristics of CT secondary ca-ble lines and the design requirements of the calibrator,this paper proposes an innovative design scheme for the calibrator.This device demonstrates significant effects in enhancing the accuracy and stability of power system calibration,providing robust technical support for the optimization and upgrade of the power system.This research not only offers a theoretical basis and practical guidance for the design and application of CT secondary cable line calibrators but also contributes new ideas and methods for the precise calibration and efficient management of the power system.
文摘With the rapid development of urban economy, distribution network construction of city is lagging behind the increment of load, and low-voltage problem has become the main complaints of the power users. Based on Python [1] scripting language, this paper develops a piece of software which can provide a friendly human-machine experience for the user, calculate the voltage of the power distribution area and propose corresponding control measures, then the paper takes the actual power distribution area to verify its effectiveness.
文摘Scaling problems and limitations of conventional silicon transistors have led the designers to exploit novel nano-technologies. One of the most promising and feasible nano-technologies is CNT(Carbon Nanotube) based transistors. In this paper, a high-speed and energy-efficient CNFET(Carbon Nanotube Field Effect Transistor) based Full Adder cell is proposed for nanotechnology. This design is simulated in various supply voltages, frequencies and load capacitors using HSPICE circuit simulator. Significant improvement is achieved in terms of speed and PDP(Power-Delay-Product) in comparison with other classical and state-of-the-art CMOS and CNFET-based designs, existing in the literature. The proposed Full Adder can also drive large load capacitance and works properly in low supply voltages.
文摘Powder metallurgy is an efficient approach to fabricate varieties of high performance structure materials, function materials and special materials working under limited conditions. Research and development of new efficient technology to form high-density, high-performance and net shape parts is a key to widen application and development of powder materials. Recently, the low-voltage electromagnetic compaction (EMC) has been used by present authors to compacted copper, tin, aluminum powders and the products with 99% relative density have been acquired. In this work, the research has been extended to investigation on the density uniformity of pressed parts. The analysis results show that the density of the part compacted by low-voltage EMC decreases gradually in press direction as static compaction. But it is higher and more homogeneous. The density of the top part increases gradually from the center to the outer, which is just reversal of the bottom part. In some extent, the higher the discharging voltage is, the higher the density is and the more homogeneous the distribution is. In addition, repetitive compaction can improve the density of powder parts and the distribution uniformity.
基金the National Natural Science Foundation of China(No.50375114)State Key Laboratory of Plastic Forming Simulation and Die & Mould Technology(No.05-03)
文摘Low-voltage electromagnetic compaction (EMC) was used to compact metal powders (Cu) and ceramic powders (TiO2) in the indirect way. It was found that the density of the metal powder parts compacted by low-voltage EMC varied linearly with the discharging voltage in the range investigated. But for ceramic powders, the discharging voltage has an optimal value. Under the value, the density increases as discharging voltage rises, but beyond the value the trend is reverse. The experimental results show that the density of the metal parts decreases gradually along press direction. And the density of the ceramic parts decreases with the advancement of the aspect ratio h/d (height/diameter). In addition, repetitive compaction can improve the density of both metal and ceramic parts and reduce the effects of aspect ratio on the density.
基金The project supported by National Natural Science Foundation of China (No. 50477025)
文摘This paper is devoted to the simulation of the arc plasma in a simplified low-voltage circuit breaker chamber. Based on a group of coupled governing equations, a three-dimensional (3-D) arc plasma model is built and solved by a modified commercial code. Firstly, this paper presents a solution of the stationary state of the arc plasma and discusses the distribution of some parameters throughout the chamber. Secondly, with the ferromagnetic materials included, the balance of the stationary state is broken and a transient course is calculated. In light of the simulation results, the temperature distribution sequence, the arc motion and the plasma jet are then described and analyzed in detail.
文摘Low-voltage distribution systems in our country are mostly used in agricultural loads and household loads. The value and using time of these kinds of loads are uncontrollable, which lead to the three-phase imbalance in low-voltage distribution system, and seriously affect the quality of power supply. A new type of the commutation system and an improved quantum genetic algorithm (IQGA) are proposed in the paper. At last, the rationality and the efficiency of the method are verified by a practical example.