The effects of rare earth elements on the microstructure and properties ofmagnesium alloy AM60B alloy were studied. Different proportions of rare earth elements were added toAM60B and the tensile tests were carried ou...The effects of rare earth elements on the microstructure and properties ofmagnesium alloy AM60B alloy were studied. Different proportions of rare earth elements were added toAM60B and the tensile tests were carried out under different temperatures. The experimental resultsshow that at room temperature the tensile strength of AM60B can be improved with the addition ofrare earth elements. The ductility of which at room or elevated temperature (120 deg C) can also beimproved, and the ductility is to some extent in proportion with the amount of rare earth elements.The ductility at 120 deg C is better than that at room temperature. The microstructure graphsdemonstrate that appropriate amount of rare earth elements (0.1 percent-0.2 percent, mass fraction)can fine AM60B's grain and improve its ductility.展开更多
Under the cold-chamber high pressure die casting （HPDC） process, samples were produced with AM60B magnesium alloy to investigate the microstructure characteristics of the eutectics, especially focusing on the consti...Under the cold-chamber high pressure die casting （HPDC） process, samples were produced with AM60B magnesium alloy to investigate the microstructure characteristics of the eutectics, especially focusing on the constitution, morphology and distribution of the eutectics over cross section of the castings. Attentions were also paid to study the effect of heat treatment on the eutectics in the die castings. Based on experimental analysis using optical microscopy （OM）, X-ray diffraction （XRD）, scanning electron microscopy （SEM） and energy-dispersive spectroscopy （EDS）, it was determined that fully divorced eutectics consisting of c^-Mg and l%MglzA112 appeared at the grain boundary of the primary c^-Mg in the as-cast microstructure. Islands and networks of β-Mg17Al12 phase were observed in the central region of the castings, while the β-Mg17Al12 phase revealed a more dispersed and granular morphology on the surface layer. The two phases ratio β/α in the central region of the castings was approximately 10%, which was higher than that on the surface layer. Besides, the defect bands contained a higher percentage of the eutectics than the adjacent regions. After aging treatment （T6）, only α-Mg phase was detected by XRD in the AM60B magnesium alloy, though a small amount of precipitated β-MgITAI12 phase was observed at the grain boundary. In contrast to the microstructure of die cast AZ91D magnesium alloy under the same T0 heat treatment, no discontinuous precipitation of the β-MgITAI12 phase was observed in AMO0B magnesium alloy die castings.展开更多
基金The program is financially supported by National Key Basic Research and Development Program of China "973"(No 2000067202).]
文摘The effects of rare earth elements on the microstructure and properties ofmagnesium alloy AM60B alloy were studied. Different proportions of rare earth elements were added toAM60B and the tensile tests were carried out under different temperatures. The experimental resultsshow that at room temperature the tensile strength of AM60B can be improved with the addition ofrare earth elements. The ductility of which at room or elevated temperature (120 deg C) can also beimproved, and the ductility is to some extent in proportion with the amount of rare earth elements.The ductility at 120 deg C is better than that at room temperature. The microstructure graphsdemonstrate that appropriate amount of rare earth elements (0.1 percent-0.2 percent, mass fraction)can fine AM60B's grain and improve its ductility.
基金the financial support of the National High Technology Research and Development Program of China (Grant No. 2009AA03Z114)the Ministry of Science and Technology of China (Grant Nos. 2011ZX04014-052, 2011BAE22B02 and 2010DFA72760)
文摘Under the cold-chamber high pressure die casting （HPDC） process, samples were produced with AM60B magnesium alloy to investigate the microstructure characteristics of the eutectics, especially focusing on the constitution, morphology and distribution of the eutectics over cross section of the castings. Attentions were also paid to study the effect of heat treatment on the eutectics in the die castings. Based on experimental analysis using optical microscopy （OM）, X-ray diffraction （XRD）, scanning electron microscopy （SEM） and energy-dispersive spectroscopy （EDS）, it was determined that fully divorced eutectics consisting of c^-Mg and l%MglzA112 appeared at the grain boundary of the primary c^-Mg in the as-cast microstructure. Islands and networks of β-Mg17Al12 phase were observed in the central region of the castings, while the β-Mg17Al12 phase revealed a more dispersed and granular morphology on the surface layer. The two phases ratio β/α in the central region of the castings was approximately 10%, which was higher than that on the surface layer. Besides, the defect bands contained a higher percentage of the eutectics than the adjacent regions. After aging treatment （T6）, only α-Mg phase was detected by XRD in the AM60B magnesium alloy, though a small amount of precipitated β-MgITAI12 phase was observed at the grain boundary. In contrast to the microstructure of die cast AZ91D magnesium alloy under the same T0 heat treatment, no discontinuous precipitation of the β-MgITAI12 phase was observed in AMO0B magnesium alloy die castings.
