Improvement in corrosion resistance of magnesium coating with cerium treatment

Corrosion protection afforded by a magnesium coating treated in cerium salt solution on steel substrate was investigated using open circuit potential, polarization curves, and electrochemical impedance spectroscopy （EIS） in 0.005 M sodium chloride solution （NaCl）. The morphology of the surface was characterized by scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, and X-ray diffraction （XRD）. The cerium treated coating was obtained by immersion in CeCl3 solution. The results showed that the corrosion resistance of the treated magnesium coating was improved. The corrosion potential of the treated coating was found to be nobler than that of the untreated magnesium coating and the corrosion current decreased significantly. Impedance results showed that the cerium treatment increased corrosion protection. The improvement of anti-corrosion properties was attributed to the formation of cerium oxides and hydroxides that gave rise to a physical barrier effect.

Preparation and Corrosion Resistance of Magnesium Coatings by Magnetron Sputtering Deposition

Magnesium coatings were fabricated on stainless steel substrates (1Cr11Ni2W2MoV) by a plane magnetron sputtering technique. The argon pressure and the substrate condition (including temperature and the substrate was rotated or fixed) were varied in order to evaluate the influence of the parameters on the crystal orientation and morphology of the coating. The corrosion behavior of the coatings in 1 wt pct NaCI solution was studied by electrochemical methods. The results showed that all coatings exhibited preferred orientation (002) as the argon pressure increased from 0.2 to 0.4 Pa. The morphologies of the coatings varied with the argon pressure and with whether the substrate was rotated or fixed. The open circuit potential of the coatings was more positive than that of cast AZ91D magnesium alloy. However, the immersion test in 1 wt pct NaCI solution showed that the corrosion rates of the coatings were higher than that of cast AZ91D magnesium alloy.

Uniform nanoplating of metallic magnesium film on titanium dioxide nanotubes as a skeleton for reversible Na metal anode

To meet the low-cost concept advocated by the sodium metal anode,this paper reports the use of a pulsed electrodeposition technology with ionic liquids as electrolytes to achieve uniform nanoplating of metallic magnesium films at around 20 nm on spaced titanium dioxide(TiO_(2))nanotubes(STNA-Mg).First,the sodiophilic magnesium metal coating can effectively reduce the nucleation overpotential of sodium metal.Moreover,three-dimensional STNA can limit the volume expansion during sodium metal plating and stripping to achieve the ultrastable deposition and stripping of sodium metals with a high Coulombic efficiency of up to 99.5%and a small voltage polarization of 5 mV in symmetric Na||Na batteries.In addition,the comparative study of sodium metal deposition behavior of STNA-Mg and STNA-Cu prepared by the same route further confirmed the advantage of magnesium metal to guide sodium metal growth.Finally,the prepared STNA-Mg-Na metal anode and commercial sodium vanadium phosphate cathode were assembled into a full cell,delivering a discharge capacity of 110.2 mAh·g^(-1)with a retention rate of 95.6%after 110 cycles at 1C rate.

Review on the phosphate-based conversion coatings of magnesium and its alloys

Magnesium(Mg)and its alloys are lightweight as well as biocompatible and possess a high strength-to-weight ratio,making them suitable for many industries,including aerospace,automobile,and medical.The major challenge is their high susceptibility to corrosion,thereby limiting their usability.The considerably lower reduction potential of Mg compared to other metals makes it vulnerable to galvanic coupling.The oxide layer on Mg offers little corrosion resistance because of its high porosity,inhomogeneity,and fragility.Chemical conversion coatings(CCs)belong to a distinct class because of underlying chemical reactions,which are fundamentally different from other types of coating.Typically,a CC acts as an intermediate sandwich layer between the base metal and an aesthetic paint.Although chromate CCs offer superior performance compared to phosphate CCs,yet still they release carcinogenic hexavalent chromium ions(Cr^(6+));therefore,their use is prohibited in most European nations under the Registration,Evaluation,Authorization and Restriction of Chemicals legislation framework.Phosphate-based CCs are a cost-effective and environment-friendly alternative.Accordingly,this review primarily focuses on different types of phosphate-based CCs,such as zinc,calcium,Mg,vanadium,manganese,and permanganate.It discusses their mechanisms,current status,pretreatment practices,and the influence of various parameters-such as pH,temperature,immersion time,and bath composition-on the coating performance.Some challenges associated with phosphate CCs and future research directions are also elaborated.

Controlling the rate of degradation of Mg using magnesium fluoride and magnesium fluoride-magnesium phosphate duplex coatings

The thin and porous Fluoride Conversion Coating FCC with many cracks could not offer a significant improvement in corrosion resistance for Mg. Magnesium phosphate coating improves the corrosion resistance of Mg, good bioactivity, promotes cell viability and cyto-compatibility and exhibits antibacterial activity. However, rapid dissolution in Mg in acidic magnesium phosphate containing solutions leads to the development of an inhomogeneous coating. The present study attempts to prevent the excessive dissolution of Mg by forming a fluoride conversion coating as a pre-treatment in the first stage followed by deposition of magnesium phosphate coating in the second stage to develop magnesium fluoride-magnesium phosphate duplex coatings. The morphological features, structural characteristics, nature of functional groups, corrosion behavior in Hanks’ balanced salt solution and bioactivity in simulated body fluid are assessed to ascertain the suitability of the magnesium fluoride-magnesium phosphate duplex coating in controlling the rate of degradation of Mg and improving its bioactivity using uncoated Mg and fluoride conversion coated Mg as reference. The findings of the study reveal that the magnesium fluoride-magnesium phosphate duplex coating could offer an excellent corrosion resistance and improve the bioactivity of Mg.

Fabrication and Evaluation of a Bioactive Sr–Ca–P Contained Micro-Arc Oxidation Coating on Magnesium Strontium Alloy for Bone Repair Application

Considering the compatibility between degradation and bioactivity of magnesium-based implants for bone repair, micro-arc oxidation is used to modify the magnesium alloy surface in aqueous electrolytes, allowing strontium, calcium, and phosphorus to be incorporated into the coating. The thickness, composition, morphology and phase of this Sr-Ca-P containing coating are characterized by scanning electron microscopy equipped with energy dispersive X-ray spectrometer and X-ray diffraction. The in vitro and in vivo degradation of the coating is evaluated by immersion test, electrochemical test and implantation test. Moreover, the cytocompatibility is tested with osteoblast cell according to ISO 10993. The results show that St, Ca and P elements are incorporated into the oxide coating, and a refined structure with tiny discharging micro-pores is observed on the surface of the coating. The Sr-Ca-P coating possesses a better corrosion resistance in vitro and retards the degradation in vivo. Such coating is expected to have significant medical applications on orthopedic implants and bone repair materials.

In Situ Aluminum Alloy Coating on Magnesium by Hot Pressing

In the present study, pure magnesium was in situ coated with pre-alloyed Al–Cu–Mg alloy through hot pressing. The produced samples were characterized by means of hardness, wear properties and microstructure characterization. A ball-on-disk test was used to determine the dry sliding wear characteristics of the compacts. The results showed that the hot pressing technique has been successfully applied for producing magnesium parts with compatible wear resistance and hardness to aluminum. The in situ coating of Al on Mg by hot pressing resulted in an increase in hardness of about 30% compared with the pure Mg substrate. The wear rate and friction coefficient of the samples decreased with Al coating and increased with an increase in the applied load during the wear tests, compared with the uncoated material.

Biofunctional magnesium coated Ti6Al4V scaffold enhances osteogenesis and angiogenesis in vitro and in vivo for orthopedic application

The insufficient osteogenesis and osseointegration of porous titanium based scaffold limit its further application.Early angiogenesis is important for scaffold survival.It is necessary to develop a multifunctional surface on titanium scaffold with both osteogenic and angiogenic properties.In this study,a biofunctional magnesium coating is deposited on porous Ti6Al4V scaffold.For osseointegration and osteogenesis analysis,in vitro studies reveal that magnesium-coated Ti6Al4V co-culture with MC3T3-E1 cells can improve cell proliferation,adhesion,extracellular matrix(ECM)mineralization and ALP activity compared with bare Ti6Al4V cocultivation.Additionally,MC3T3-E1 cells cultured with magnesium-coated Ti6Al4V show significantly higher osteogenesisrelated genes expression.In vivo studies including fluorochrome labeling,micro-computerized tomography and histological examination of magnesium-coated Ti6Al4V scaffold reveal that new bone regeneration is significantly increased in rabbits after implantation.For angiogenesis studies,magnesium-coated Ti6Al4V improve HUVECs proliferation,adhesion,tube formation,wound-healing and Transwell abilities.HUVECs cultured with magnesium-coated Ti6Al4V display significantly higher angiogenesis-related genes(HIF-1αand VEGF)expression.Microangiography analysis reveal that magnesium-coated Ti6Al4V scaffold can significantly enhance the blood vessel formation.This study enlarges the application scope of magnesium and provides an optional choice to the conventional porous Ti6Al4V scaffold with enhanced osteogenesis and angiogenesis for further orthopedic applications.

Surface Modification on Biodegradable Magnesium Alloys as Orthopedic Implant Materials to Improve the Bio-adaptability:A Review

Magnesium （Mg） and its alloys as a novel kind of biodegradable material have attracted much funda- mental research and valuable exploration to develop its clinical application, Mg alloys degrade too fast at the early stage after implantation, thus commonly leading to some problems such as osteolysis, early fast mechanical loss, hydric bubble aggregation, gap formation between the implants and the tissue. Surface modification is one of the effective methods to control the degradation property of Mg alloys to adapt to the need of organism. Some coatings with bioactive elements have been developed, especially for the micro-arc oxidation coating, which has high adhesion strength and can be added with Ca, P, and Sr elements. Chemical deposition coating including bio-mimetic deposition coating, electro-deposition coating and chemical conversion coating can provide good anticorrosion property as well as better bioactivity with higher Ca and P content in the coating. From the biodegradation study, it can be seen that surface coating protected the Mg alloys at the early stage providing the Mg alloy substrate with lower degra-dation rate. The biocompatibility study showed that the surface modification could provide the cell and tissue stable and weak alkaline surface micro-environment adapting to the cell adhesion and tissue growth. The surface modification also decreased the mechanical loss at the early stage adapting to the load- bearing requirement at this stage. From the interface strength between Mg alloys implants and the surrounding tissue study, it can be seen that the surface modification improved the bio-adhesion of Mg alloys with the surrounding tissue, which is believed to be contributed to the tissue adaptability of the surface modification. Therefore, the surface modification adapts the biodegradable magnesium alloys to the need of hiodegradation, biocompatibility and mechanical loss property. For the different clinical application, different surface modification methods can be provided to adapt to the clinical requirements for the Mg alloy implants.

Corrosion resistance of a superhydrophobic micro-arc oxidation coating on Mg-4Li-1Ca alloy

A micro-arc oxidation（MAO）/zinc stearate（ZnSA） composite coating was fabricated via MAO processing and subsequent sealing with electrodeposition of a superhydrophobic ZnSA. The surface morphologies,chemical composition and corrosion resistance of the coatings were investigated using field-emission scanning electron microscopy, Fourier transform infrared, X-ray diffraction and electrochemical and hydrogen evolution measurements. Results indicated that the MAO coating was efficiently sealed by the following superhydrophobic ZnSA coating. The MAO/ZnSA composite coating significantly enhanced the corrosion resistance of Mg alloy Mg-4 Li-1 Ca due to its superhydrophobic function. Additionally, corrosion mechanism was suggested and discussed for the composite coating.

Plasma electrolytic oxidation of the magnesium alloy MA8 in electrolytes containing TiN nanoparticles

The formation of protective multifunctional coatings on magnesium alloy MA8 using plasma electrolyt- ic oxidation （PEO） in an electrolytic system containing nanosized particles of titanium nitride was investigated. Electrochemical and mechanical properties of the obtained layers were examined. It was established that microhardness of the coating with the nanoparticle concentration of 3 gl-1 increased twofold （4.2 ± 0.5 GPa）, while wear resistance decreased （4.97 × 10-6 mm3 N-1 m-1）, as compared to re- spective values for the PEO-coating formed in the electrolyte without nanoparticles （2.1 ± 0.3 GPa, 1.12 × 10.5 mm3 N-1 m-1）.