Effects of fluid recirculation on mass transfer from the arterial surface to flowing blood

The effect of disturbed flow on the mass trans- fer from arterial surface to flowing blood was studied nu- merically, and the results were compared with that of our previous work. The arterial wall was assumed to be vis- coelastic and the blood was assumed to be incompressible and non-Newtonian fluid, which is more close to human arte- rial system. Numerical results indicated that the mass trans- fer from the arterial surface to flowing blood in regions of disturbed flow is positively related with the wall shear rates and it is significantly enhanced in regions of disturbed flow with a local minimum around the reattachment point which is higher than the average value of the downstream. There- fore, it may be implied that the accumulation of cholesterol or lipids within atheromatous plaques is not caused by the reduced efflux of cholesterol or lipids, but by the infiltration of the LDL （low-density lipoprotein） from the flowing blood to the arterial wall.

Design of fan beam optical sensor and its application in mass flow rate measurement of pneumatically conveyed solids

The fan-beam optical sensor is made up of many semiconductor lasers and detectors fixed around the wall alternately at a cross section of pneumatically conveying pipe. When the sensor works, a scanning light source emits a 50° lamellar fan-beam through the gas-solid two phase flow, and the projection data resulting extinction effect of solid particles are detected at the same time. With the projection data, the flow rate mass can be calculated, and then the flow image can be reconstructed. In this paper, the design of the sensor including spatial arrangement of the structural parts, basic principle and measurement sensitivity distribution are introduced. The mathematical measurement model of solid mass flow rate is presented together with the testing results.

A New Method for Measurement of Helium Mass Flow Rate in the Cryogenic System of TORE SUPRA

The TORE SUPRA Tokamak was built by EURATOM-CEA association. The NbTi conductor of superconducting coils is inserted in a tight enclosure filled with pressurized superfluid helium of 0.125 MPa at 1.8 K. The thick casing is cooled to 4.5 K by 1.8 MPa in 4.5 K supercritical helium circulation. Around this thick casing, a 80 K thermal shield protects the parts at very low temperatures from the thermal radiation, which is cooled by pressurized helium at 80 K and 1.8 MPa. A new measurement method for helium mass flow rate of 80 K shield and 4.5 K casing is described in this paper. The commissioning was done on the two helium loops of the cryoplant: the supercritical 4.5 K thick casing and 80 K shields. The purpose is to improve control of the 4.5 K and 80 K refrigeration loops.

Lumped Parameter Mass Flow Rate and Pressure Control Characteristics Model for High-Speed Pneumatic PWM on/off Valve

Aiming at solving the problem of strong coupling characteristic of the key parameters of high-speed pneumatic pulse width modulation( PWM) on / off valve, a general lumped parameter mathematical model based on the valves time periods was well developed. With this model,the mass flow rate and dynamic pressure characteristics of constant volumes controlled by high-speed pneumatic PWM on /off valves was well described. A variable flow rate coefficient model was proposed to substitute for the constant one used in most of the prior works to investigate PWM on /off valves' dynamical pressure response, and a formula for disclosing the inherent relationship among the PWM command signal,static mass flow rate,and sonic conductance of the valve was newly derived.Finally,an extensive set of analytical experimental comparisons were implemented to verify the validity of the proposed mathematica model. With the proposed model, PWM on /off valves' characteristics,such as mass flow rate,step pressure response of the valve control system,mean pressure and ripple amplitude,not only in the linear range,but also in the nonlinear range can be wel predicted; Good agreement between measured and calculated results was obtained,which proved that the model is helpful for designing a control strategy in a closed loop control system.

MASS FLOW RATE INDUCED BY COMBINED ROOF SOLAR COLLECTOR AND VERTICAL STACK IN A HOT HUMID CLIMATE

This paper presents the investigation of solar induced ventilation that utilizes roof solar collector and vertical stack. Three prototypes, namely A, B and C, were developed based on preliminary experimental work. They were then used in simulation study with the objective of determining the prototype that was able to induce the highest mass flow rate. The validation of simulation modelling against experiment indicated a good agreement between these two results. The findings showed that prototype A induced the highest mass flow rate. However, prototype C, which had obstructions at the stack outlets, was more appropriate for application in Malaysia due to various prevailing wind directions. In addition, the findings also indicated that besides solar radiation, the mass flow rate induced by the prototypes was also influenced by the local wind direction, the inlet and outlet positions as well as the outlet design. In summary, the findings highlighted the potential application of the proposed solar induced ventilation in a hot and humid climate.

Impact of well placement and flow rate on production efficiency and stress field in the fractured geothermal reservoirs

Geothermal energy has gained wide attention as a renewable alternative for mitigating greenhouse gas emissions.The advancements in enhanced geothermal system technology have enabled the exploitation of previously inaccessible geothermal resources.However,the extraction of geothermal energy from deep reservoirs poses many challenges due to high‐temperature and high‐geostress conditions.These factors can significantly impact the surrounding rock and its fracture formation.A comprehensive understanding of the thermal–hydraulic–mechanical(THM)coupling effect is crucial to the safe and efficient exploitation of geothermal resources.This study presented a THM coupling numerical model for the geothermal reservoir of the Yangbajing geothermal system.This proposed model investigated the geothermal exploitation performance and the stress distribution within the reservoir under various combinations of geothermal wells and mass flow rates.The geothermal system performance was evaluated by the criteria of outlet temperature and geothermal productivity.The results indicate that the longer distance between wells can increase the outlet temperature of production wells and improve extraction efficiency in the short term.In contrast,the shorter distance between wells can reduce the heat exchange area and thus mitigate the impact on the reservoir stress.A larger mass flow rate is conducive to the production capacity enhancement of the geothermal system and,in turn causes a wider range of stress disturbance.These findings provide valuable insights into the optimization of geothermal energy extraction while considering reservoir safety and long‐term sustainability.This study deepens the understanding of the THM coupling effects in geothermal systems and provides an efficient and environmentally friendly strategy for a geothermal energy system.

Experimental Analysis of the Flow Characteristics of an Adjustable Critical-Flow Venturi Nozzle

The response of an adjustable critical-flow Venturi nozzle is investigated through a set indoor experiments aimed to determine the related critical flow rate,critical pressure ratio,and discharge coefficient.The effect of a variation in the cone displacement and liquid content on the critical flow characteristics is examined in detail and it is shown that the former can be used to effectively adjust the critical flow rate.The critical pressure ratio of the considered nozzle is above 0.85,and the critical flow control deviation of the gas flow is within±3%.Liquid flow can reduce the gas critical mass flow rate accordingly,especially for the cases with larger liquid volume and lower inlet pressure.The set of results and conclusions provided are intended to support the optimization of steam injection techniques in the context of heavy oil recovery processes.

A Numerical Simulation of Air Flow in the Human Respiratory System Based on Lung Model

The lung is an important organ that takes part in the gas exchange process. In the study of gas transport and exchange in the human respiratory system, the complicated process of advection and diffusion (AD) in airways of human lungs is considered. The basis of a lumped parameter model or a transport equation is modeled during the inspiration process, when oxygen enters into the human lung channel. The quantitative measurements of oxygen are detached and the model equation is solved numerically by explicit finite difference schemes. Numerical simulations were made for natural breathing conditions or normal breathing conditions. The respiratory flow results for the resting conditions are found strongly dependent on the AD effect with some contribution of the unsteadiness effect. The contour of the flow rate region is labeled and AD effects are compared with the variation of small intervals of time for a constant velocity when breathing is interrupted for a negligible moment.

Numerical Study of Fluid Flow over Bundle Tubes

In this paper, a bank of tubes containing a flowing fluid which is immersed in a cross flow second medium of fluid with different temperature has been studied numerically using computational fluid dynamics. Laminar steady flow with a low Reynolds number has been studied in this work. Inlet mass flow rate and the bulk temperature are known and numerical method has been implemented to study the convective heat transfer to investigate the temperature and flow fields. Effects of different inlet bulk temperatures and mass flow rates have been investigated on temperature and pressure variations.

Effects of bleed hole size on supersonic boundary layer bleed mass flow rate

The bleed hole diameter,depth,and boundary layer thickness are key design parameters of a supersonic bleed system.The evolution trend of single-hole bleed flow coefficient with the ratio of boundary layer thickness to bleed hole diameter and the ratio of bleed hole depth to diameter is investigated by numerical simulations under choking and non-choking conditions.The results show that the subsonic leading edge of the circular hole and the subsonic part of the boundary layer are the main factors causing lateral flow of the bleed hole.The effect of diameter on bleed mass flow rate is due to the viscous effect which reduces the effective diameter.The larger the ratio of displacement thickness to bleed hole diameter,the more obvious the viscous effect is.The depth affects bleed flow rate by changing the opening and closing states of the separation zone.When a certain depth is reached,the development of the boundary layer reduces the effective captured stream tube and thus reduces the bleed mass flow rate.The main objective of the study is to obtain the physical mechanism of the bleed hole size parameters affecting the bleed mass flow rate,and to provide theoretical guidance for the selection of the size of bleed holes in the design of a porous arrays bleed system in hypersonic inlets.

Influences of mass flow rate on heat and mass transfer performances of water sublimator combined with fluid loop

For spacecraft working in vacuum environment, sublimator is an effective heat rejection approach to reject system's peak heat load, and supplement spacecraft radiation heat rejection. For a spacecraft active fluid loop thermal control system combined with sublimator, waste heat generated from multi-point distributed heat sources could be collected by the fluid loop efficiently. However, the heat and mass transfer performances of the sublimator combined with fluid loop have not been adequately studied in previous research, especially for the influences of the heat load. Since work fluid mass flow rate is the main factor affecting heat load of the fluid loop, this context experimentally studied influences of the fluid loop mass flow rate on sublimator start-up transient characteristics, including heat transfer performances, response time, and work stability. Results indicated that the fluid loop mass flow rate affected the sublimator heat and mass transfer performances obviously, but the heat rejection ability is not always increase with the increasing of the fluid loop mass flow rate. In addition, we obtained the condition to judge whether there is a positive correlation between heat rejection ability and fluid loop mass flow rate.

Cathode erosion site distributions in an applied-field magnetoplasmadynamic thruster

Erosion can influence cathode life,and is thus considered to be one of the main factors limiting the application of applied-field magnetoplasmadynamic thrusters.In this paper,erosion sites on graphite cathodes are studied so as to identify the influence of applied magnetic field and the ratio of propellant mass flow rate supplied from cathode and anode.The experiment results show that the application of applied magnetic field can significantly reduce the erosion rate of the cathode compared to that without magnetic field.The erosion sites on the cathode vary with the relative position of the convergent-divergent magnetic field,and are mainly distributed in the divergent part of the field.The erosion sites on the cathodes are found to be related to the propellant supply.The decreasing anode mass flow rate enlarges the range of erosion.These results are much helpful for the analysis of cathode erosion site location since they provide evidences of erosion mechanisms and point out the directions for further research.

Effects of Geometric Parameters on Performance of Rectangular Submerged Inlet for Aircraft

To improve the comfortability and safety of aircraft,the demand of rectangular submerged inlets(RSIs)with low resistance is proposed to increase the inlet flow rate of ram air. A theoretical model is built to numerically analyze the effects of geometric parameters on the inlet mass flow rate of RSIs. The geometric parameters in question here encompass the aspect ratio of 2—4,the ramp angle of 6°—7°,the characteristic parameter of the throat of 0.20 —0.30,the ramp length of 939—1 337 mm,and the cone angle of 0° —3°. Simulation results demonstrate that the mass flow rate(MFR)is positively correlated with the aspect ratio,ramp angle,ramp length,and cone angle,and negatively correlated with characteristic parameter of the throat. Within the range of the geometric parameters considered,the RSI with the aspect ratio of 3,the ramp angle of 6°,the characteristic parameter of the throat of 0.20,the ramp length of 1 337 mm,and the cone angle of 3° obtains the largest MFR value of about 2.251 kg/s.

Large Eddy Simulation of Micro-Particles Transport with Different Mass Flow Rate in Turbulent Planar Jet Flow

The motion of micro-particles with different mass flow rate in the planer turbulent jet flow has been simulated, using LES method to obtain the flow vorticity evolution and Lagrangian method to track micro-particles. The re- suits showed that when the flow rate is small, the particles more likely to present in the vortex periphery, the dis- tribution pattern is similar to the flow pattern. When the flow rate is high, some particles will escape from the mo- tion region to the original static region, so that in the jet region, particles are relatively evenly distributed. When the flow field is full developed, the particles average concentration in the y direction affected by the mass flow rate relative slightly, the normalized mean particles concentrations at different flow rate were similar to Gaussian shape.

Experiments on an Open-Loop Cycle Carbon Dioxide Refrigeration System

An open loop cycle carbon dioxide(CO2)refrigeration system is established,and the cooling performances of high-pressure CO2 under different storage conditions(25℃,30℃,and 35℃)are investigated.Moreover,the experimental mass flow rates of CO2 are compared with the theoretical values at different conditions and refrigeration capacities.The results indicate that the storage condition of CO2 has a significant impact on the refrigeration performance,and the mass flow rate of CO2 increases with the increasing storage temperature in a given refrigeration capacity.

Optimal Design of Two-Chamber Gas Distributor with CFD Approach

Computational fluid dynamics( CFD) is used to investigate a new type of two-chamber natural gas distributor,which has a natural gas inlet and nine nozzle outlets. The uniformity at the outlet of distributor is practice proven to have significant degree influence on its comprehensive performance. To improve the uniformity at the nozzles of the gas distributor,CFD modeling with the RNG k-ε turbulence model is undertaken to understand the mass flow rate of nozzles with reference to different length of chambers and the most optimal length is obtained. The internal flow pattern of the natural gas distributor is analyzed. It is found that the local maximum deviation of the nozzle outflow rate increases with the increase of chambers length when the length is more than 64 mm. The results provide useful suggestions for the optimal design of two-chamber natural gas distributor.

DOUBLE LOOP ACTIVE VIBRATION CONTROL OF PNEUMATIC ISOLATOR WITH TWO SEPARATE CHAMBERS

A newly designed pneumatic spring with two separate chambers is promoted and double-loop active control is introduced to overcome the following drawbacks of passive pneumatic isolation： ① The low frequency resonances introduced into the system; ② Conflict between lower isolation frequency and stiffness high enough to limit quasi-static stroke;③ Inconsistent isolation level with different force load. The design of two separate chambers is for the purpose of tuning support frequency and force independently and each chamber is controlled by a different valve. The inner one of double-loop structure is pressure control, and in order to obtain good performance, nonlinearities compensation and motion flow rate compensation （MFRC） are added besides the basic cascade compensation, and the influence of tube length is studied. The outer loop has two functions： one is to eliminate the resonance caused by isolation support and to broaden the isolation frequency band by payload velocity feedback and base velocity feed forward, and the other is to tune support force and support stiffness simultaneously and independently, which means the support force will have no effect on support stiffness. Theoretical analysis and experiment results show that the three drawbacks are overcome simultaneously.

Theoretical and Experimental Investigations of Solar Heating Systems at Specified Output Conditions of Hot Water

The theoretical analysis discussed in this work is a suitable mathematical tool by which the performance of the proposed collector can be predicted. The obtained experimental results coincide with the obtained theoretical data obtained from the devised computer program. Controlled output temperature can be obtained from the proposed system. The performance of the tested collector under the proposed intermittent flow conditions overcomes that of the conventional thermosyphone flow collector.

Numerical Study of Conjugate Heat Transfer for Cooling the Circuit Board

In this paper, a 3D model of a flat circuit board with a heat generating electronic chip mounted on it has been studied numerically. The conjugate heat transfer including the conduction in the chip and convection with the surrounding fluid has been investigated numerically. Computational fluid dynamics using the finite volume method has been used for modeling the conjugate heat transfer through the chip and the circuit board. Conjugate heat transfer has broad applications in engineering and industrial applications in design of cooling off electronic components. Effects of various inlet velocities have been studied on the heat transfer variation and temperature of the circuit board. Numerical results show that the temperature of the chip reduces as the velocity of the inlet fluid flow increases.

Structure of low-head two-phase flow in flat nozzlesduring outflow of the liquid into rarefied medium

Outcomes of experimental researches of the low-pressure adiabatic flow of the boiling liquid through two-dimensional Laval nozzles in a vacuum atmosphere were adduced.Requirements of critical conditions of flow were determined.Structural forms of a stream were investigated and their connection with crisis of flow was shown.It was established periodic non-stationary macrostructures of a stream which was stipulated by the rotational gear of origin of a vapor phase.